Effects of Supporting Electrolytes on Spectroelectrochemical and Electrochromic Properties of Polyaniline‐poly(styrene sulfonic acid) and Poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid)‐based Electrochromic Device

Electrochromic devices are fabricated by using polyaniline (PANI) doped with poly(styrene sulfonic acid) (PSS) as coloring electrodes, poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid) (PEDOT‐PSS) as complementary electrodes, and hybrid polymer electrolytes as gel electrolytes. The device based on LiClO₄‐based electrolyte (weight ratio of PMMA:PC:LiClO₄ = 0.7:1.1:0.3) shows the highest optical contrast and coloration efficiency (333 cm²/C) after 1200 cycles in these devices, and the color changes from pale yellow (?0.5 V) to dark blue (+2.5 V). The spectroelectrochemical and electrochromic switching properties of electrochromic devices are investigated, the maximum optical contrast (ΔT%) of electrochromic device for ITO|PANI‐PSS‖PMMA‐PC‐LiClO₄‐SiO₂‖PEDOT‐PSS|ITO are 31.5% at 640 nm, and electrochromic device based on LiClO₄‐based electrolyte with SiO₂ shows faster response time than that based on LiClO₄‐based electrolyte without SiO₂.     

Performance of gelled-type dye-sensitized solar cells associated with glass transition temperature of the gelatinizing polymers

Poly(methyl acrylate) (PMA), poly(vinyl acetate) (PVAc) and poly(n-isopropylacrylamide) (PNIPAAm) with their respective T_g of 6, 32, and 145 °C were employed to gel the LiI/I₂/tertiary butylpyridine electrolyte system for preparation of the gelled-type dye-sensitized solar cells (DSSC). The light-to-electricity conversion efficiencies of DSSCs gelled by PMA, PVAc, and PNIPAAm were 7.17%, 5.62%, and 3.17%, respectively under simulated AM 1.5 sunlight irradiation, implying that utilizing the polymer of lower T_g to gel the electrolytes leaded to better performance of the DSSCs. Their short-circuit current density and IPCE also showed the similar trend. Electrochemical impedance spectroscopy of the gelled DSSCs revealed that utilizing the polymer of lower T_g resulted in lower impedance associated with the Nernstian diffusion within the electrolytes. The results were consistent with the observation that the molar conductivity of gelled electrolytes was higher as the polymer of lower T_g was applied, which can be justified by Vogel-Tammann-Fulcher (VTF) equation.     

Ionic conductivity and compatibility studies of blends of poly(methyl methacrylate) and poly(propylene glycol) complexed with LICF3SO3

Stable to atmospheric moisture, adhesive and transparent polymer electrolytes have been prepared by blending poly(methyl methacrylate) (PMMA) with poly(propylene glycol)-425/LiCF₃SO₃ complexes. The blending of the polymers has been achieved by a method developed in our laboratory: free radical polymerization of methylmethacrylate in the polyether/salt matrix. A series of polymer blend complexes varying in PMMA content (up to 20% by weight) and oxygen/metal ratios (25, 16, and 8) have been synthesized and their properties studied. All the samples prepared in this study were found to be optically clear unlike the higher molecular weight poly(propylene glycol)-2000 (PPG-2000) system which required a minimum salt concentration to compatibilize a specific amount of PMMA with PPG. The mechanisms by which the salt holds the otherwise incompatible polymers together in a single phase have been investigated by FT-IR. Our studies show a weak coupling of the ether oxygens in the PPG with the ester groups of the PMMA through the lithium cations. Discrete changes has been observed in the FT-IR spectrum of PMMA when doped with the lithium salt hitherto unnoticed with other dopants. Gel permeation chromatography results of the PMMA samples isolated from the solid electrolytes indicate the molecular weight to vary between 43000 and 121000 with relatively narrow distributions, 1.6?2.0. The ionic conductivities of the polymer blend electrolytes were fairly high (10^?5 S/cm) at room temperature. The PMMA neither significantly influenced the T_g of the blend complexes nor effected the ionic conductivities drastically. The ionic conductivity as a function of temperature followed the empirical Vogel-Tammann-Fulcher equation. The blending of PMMA with PPG/LiCF₃SO₃ complexes was found to impart good adhesiveness to the solid electrolytes while making them stable to atmospheric moisture. © 1992 John Wiley & Sons, Inc.     

High ionic conductive PVDF-based fibrous electrolytes

The high ionic conductive polymer electrolytes were prepared based on poly(vinylidenefluoride) (PVDF) fibers modified via preirradiation grafting poly(methyl methacrylate) (PMMA). In these polymer electrolytes, the PVDF fibers served as the supporting phase providing dimensional stability, and PMMA acted as the gel phase helping for the trapping liquid electrolyte and substituting the nonconductive PVDF phase to provide contact with electrodes well thus increasing conductive area. The modified PVDF fibrous membranes were used as a polymer electrolyte in lithium ion battery after they were activated by uptaking 1 M LiPF₆/ethylene carbonate–dimethyl carbonate (1:1 vol) liquid electrolyte, which showed a much higher room-temperature ionic conductivity than the pristine PVDF fibrous membrane. The LiCoO₂-mesocarbon microbead coin cells containing the dual-phase fibrous membrane (degree of graft, 111.8%) demonstrated excellent rate performance, and the cell still retained about 86% of discharge capacity at 4C rate, as compared to that at 0.1C rate. The prototype cell showed good cycle performance.     

Ionic transport in P(VDF-HFP)-PMMA-LiCF3SO3-(PC + DEC)-SiO2 composite gel polymer electrolyte

Composite gel polymer electrolytes composed of poly(vinylidene fluoride-co-hexafluoropropylene) P(VDF-HFP) and polymethylmethacrylate PMMA polymers, PC + DEC as plasticizer and LiCF₃SO₃ as salt and fumed silica as filler have been synthesized by solvent casting technique with varying plasticizer-filler ratio systematically. Films of thickness in the range of 40-70 μm were characterized by a.c. impedance measurements in the temperature range 303 K to 373 K. Addition of filler to the polymer electrolyte was found to result in an enhancement of the ionic conductivity. A maximum electrical conductivity of ∼1 × 10⁻³ S/cm at 303 K and ∼2.1 × 10⁻³ S/cm at 373 K has been achieved with the dispersion of the SiO₂. FTIR spectral studies confirmed the polymer-salt interaction. XRD patterns exhibit the increased amorphicity in the blended composite gel polymer electrolytes. Scanning electron micrograph shows the dispersion of SiO₂ particle in the polymer electrolyte.     

Review on gel polymer electrolytes for lithium batteries

This paper reviews the state-of-art of polymer electrolytes in view of their electrochemical and physical properties for the applications in lithium batteries. This review mainly encompasses on five polymer hosts namely poly(ethylene oxide) (PEO), poly(acrylonitrile) (PAN), poly(methyl methacrylate) (PMMA), poly(vinylidene fluoride) (PVdF) and poly(vinylidene fluoride-hexafluoro propylene) (PVdF-HFP) as electrolytes. Also the ionic conductivity, morphology, porosity and cycling behavior of PVdF-HFP membranes prepared by phase inversion technique with different non-solvents have been presented. The cycling behavior of LiMn₂O₄/polymer electrolyte (PE)/Li cells is also described.     

Electrical and Structural Properties of Poly (Methyl Methacrylate) Doped Potassium Iodide (KI) Solid Polymer Electrolyte

A high-conducting salt-doped polymer electrolyte layer has been created here for use in photocell technologies. The solution casting method is used to produce ion conducting film where poly (methyl methacrylate) (PMMA) is used as the host polymer and potassium iodide (KI) as the dopant. The conductivity and amorphic increases of the polymer electrolytes with the addition of salt concentrations helps in the enhancement of the charge transfer properties. Using electrochemical impedance spectroscopy (EIS), ionic conductivity is evaluated where maximum conductivity is 3.99 × 10⁻⁶ S cm^-1 at 20 wt% KI concentration. Polarized optical microscopy (POM) shows the reduction in crystallinity by salt doping, while Fourier transforms infrared spectroscopy (FTIR) shows the complexation as well as composite nature of the film. Ionic transference number (t_ion) measurement shows the predominantly ionic nature of this polymer electrolyte.     

Investigations on poly(methyl methacrylate)-poly(ethylene oxide) hybrid polymer electrolytes with dioctyl phthalate, dimethyl phthalate and diethyl phthalate as plasticizers

Plasticizers can be used to change the mechanical and electrical properties of polymer electrolytes by reducing the degree of crystallinity and lowering the glass transition temperature. The transport properties of gel-type ionic conducting membranes consisting of poly(ethylene oxide) (PEO), poly(methyl methacrylate) (PMMA), LiClO₄ and dioctyl phthalate, diethyl phthalate or dimethyl phthalate (DMP) are studied. The polymer films are characterized by X-ray diffraction, Fourier transform infrared and impedance spectroscopic studies. It is found that the addition of DMP as the plasticizer in the PEO-PMMA-LiClO₄ polymer complex favours an enhancement in ionic conductivity. The maximum conductivity value obtained for the solid polymer electrolyte film at 305 K is 3.529×10^{– 4} S cm^–1. Electronic Publication     

The network gel polymer electrolyte based on poly(acrylate-co-imide) and its transport properties in lithium ion batteries

Poly (acrylate-co-imide)-based gel polymer electrolytes are synthesized by in situ free radical polymerization. Infrared spectroscopy confirms the complete polymerization of gel polymer electrolytes. The ionic conductivity of gel polymer electrolytes are measured as a function of different repeating EO units of polyacrylates. An optimal ionic conductivity of the poly (PEGMEMA₁₁₀₀-BMI) gel polymer electrolyte is determined to be 4.8 × 10^–3 S/cm at 25 °C. The lithium transference number is found to be 0.29. The cyclic voltammogram shows that the wide electrochemical stability window of the gel polymer electrolyte varies from −0.5 to 4.20 V (vs. Li/Li⁺). Furthermore, we found the transport properties of novel gel polymer electrolytes are dependent on the EO design and are also related to the rate capability and the cycling ability of lithium polymer batteries. The relationship between polymer electrolyte design, lithium transport properties and battery performance are investigated in this research.     

A novel sandwiched membrane as polymer electrolyte for application in lithium-ion battery

A novel kind of sandwiched polymer membrane was prepared, which consists of two outer layers of electrospun poly(vinyl difluoride) (PVDF) fibrous films and one inner layer of poly(methyl methacrylate) (PMMA) film. Its characteristics were investigated by scanning electron microscopy and X-ray diffraction. The membrane can easily absorb non-aqueous electrolyte to form gelled polymer electrolytes (GPEs). The resulting gelled polymer electrolytes had a high ionic conductivity up to 1.93 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 4.5 V (vs. Li/Li⁺). It is of great potential application in polymer lithium-ion batteries.     

Electrochemical investigation of gel polymer electrolytes based on poly(methyl methacrylate) and dimethylacetamide for application in Li-ion batteries

In the present work, gel polymer electrolytes (GPEs) were prepared using poly(methyl methacrylate) (PMMA), lithium perchlorate (LiClO₄) and dimethylacetamide as a plasticizer. Solution-casting technique was used to fabricate GPEs containing different weight percentage of PMMA. The degree of crystallinity of GPE samples was studied by X-ray diffraction (XRD) analysis. Fourier transform infrared (FT-IR) spectroscopy was applied to study the level of interactions between lithium salt and PMMA in the prepared GPEs. Electrochemical properties were studied by electrochemical impedance spectroscopy, linear sweep voltammetry and DC polarization techniques. Lithium ion conductivity of GPEs was determined by calculating the bulk resistance of polymer electrolytes from Nyquist plot. Increasing PMMA content of GPEs resulted in an improvement in the electrochemical potential window from 4.2 to 4.5 V. The highest lithium transference number (0.42) and also the best electrochemical properties were obtained for GPE containing 0.75 M LiClO₄ and 10 wt% PMMA. Scanning electron microscopy images of the optimized GPE showed a porous and heterogeneous surface structure which is desirable for application in Li-ion batteries.     

Solid polymer electrolytes X: Preparation and characterizations of polyether–siloxane,organic–inorganic,hybrid nanocomposites complexed with lithium perchlorate

Organic–inorganic hybrid nanocomposites of poly(ethylene glycol)/siloxane were obtained via the sol–gel approach. In these composites, nanometric siloxane heterogeneity was embedded into a polymer matrix with a covalent bond at the interfaces. The ²⁹Si magic-angle spinning (MAS) spectrum exhibited a high degree of condensation through the relative abundance of T⁰ [RSi(OR)₃], T¹ [RSi(OR)₂(OSi)], T² [RSi(OR)(OSi)₂], and T³ [RSi(OSi)₃] silicone nuclei. The effect of lithium salt concentration on ionic interaction, conductivity, and thermal properties of these composite electrolytes were investigated by Fourier transform infrared spectroscopy, DSC, thermogravimetric analysis, alternating current impedance, and solid-state ⁷Li MAS NMR measurements. These observations indicated that the different types of complexes by the interactions of Li⁺ and ClO ions are formed within a hybrid host, and the formation of transient crosslinks between Li⁺ ions and the ether oxygens results in an increased glass-transition temperature of the polyether segment and decomposed rate of composite electrolyte. ⁷Li MAS NMR measurements revealed the changes in line shape of lithium resonances with different LiClO₄ contents, suggesting that a significant degree of ionic association is present in the polymer-salt complexes. The behavior of ion transport in these composite electrolytes was correlated with the interactions between ions and polymer host. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1928–1937, 2004     

Interfacial stability of compatibilizers dictated by the thermodynamic interactions in an immiscible system and the effects of micelles on the crystallization of PLLA

Poly(L-lactic acid) (PLLA) is blended with three acrylonitrile-butadiene-styrene (ABS) materials and compatibilized by a kind of poly(methyl methacrylate) (PMMA)-type reactive comb (RC) polymer (RC). The compatibilization efficiency is found to be dictated by the thermodynamic interactions between PMMA-type compatibilizers and ABS materials. For one type of ABS, which is composed of methyl methacrylate (MMA), styrene (St), acrylonitrile (AN), and butadiene (BD), the MMA component of ABS is able to strengthen the interaction between the PMMA-type compatibilizers and the ABS phase and thus the obtained compatibilized PLLA/ABS blends display a fine cocontinuous morphology and excellent mechanical properties. For the other two ABS materials, which are constituted by St, AN, and BD, it has been found that the PMMA-type compatibilizers are pulled out from the interface to form micelles in the PLLA phase, on account of the weakening interactions between ABS and PMMA-type compatibilizers. The thus formed micelles can interact with the crystallization of PLLA and the melting temperature (T_m) of PLLA is split into a lower and a higher peak firstly, compared to the T_m of neat PLLA, then significantly decrease to lower temperature, with increasing the amount of micelles in the PLLA phase. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 372–382     

Plasticized polymer electrolyte membranes based on PEO/PVdF-HFP for use as an effective electrolyte in lithium-ion batteries

Plasticized polymer electrolytes were prepared using poly(ethylene oxide)(PEO)/poly(vinylidene fluoridehexafluoro propylene)(PVd F-HFP) with lithium perchlorate(Li Cl O4) and different plasticizers. XRD and FTIR spectroscopic techniques were used to characterize the structure and the complexation of plasticizer with the host polymer matrix. The role of interaction between polymer hosts and plasticizer on conductivity is discussed using the results of alternating current(a.c.) impedance studies. TG-DTA and SEM were used for thermal and physical characterizations. Maximum ionic conductivity(3.26 × 10~(-4) S·cm~(-1)) has been observed for ethylene carbonate(EC)-based polymer electrolytes. Electrochemical performance of the plasticized polymer electrolyte is evaluated in LiFePO_4/plasticized polymer electrolytes(PPEs)/Li coin cell. Good performance with low capacity fading on charge discharge cycling is demonstrated.     

Effect of ion content in ionomer on the ion conductivity of polymer electrolytes based on the P(MMA-co-LiMA)/PEG/LiCF3SO3 blend

We have prepared polymer electrolytes composed of poly(methyl methacrylate-co-lithium methacrylate) ionomer (P(MMA-co-LiMA)), low molecular weight PEG, and LiCF₃SO₃ salt. The ion groups in P(MMA-co-LiMA) could enhance the miscibility between the MMA units and PEG in the polymer electrolytes. This miscibility enhancement made the pathway of ion transport less tortuous, and consequently led to the increase in ion conductivity. The maximum ambient ion conductivities in these systems were measured to be in the range of 10⁻⁴–10⁻⁵ S/cm. The polymer electrolytes became transparent at the higher ion content owing to the enhanced miscibility. The mechanical stability of the polymer electrolytes was also improved through the introduction of ion groups into the PMMA. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 991–997, 1998     

Thermal and electrochemical characteristics of plasticized polymer electrolytes based on poly(acrylonitrile-co-methyl methacrylate)

The thermal and electrochemical characteristics of plasticized polymer electrolytes composed of poly(acrylonitrile-co-methyl methacrylate) [P(AN-co-MMA)], a plasticizer [a mixture of ethylene carbonate and propylene carbonate], and LiCF₃SO₃ were investigated. The incorporation of a MMA unit into the matrix polymer was effective for an increase in the compatibility between the matrix polymer and the plasticizer. The comparative investigation of the interfacial resistance of the Li/polymer electrolyte/Li cell for the PAN-based and the P(AN-co-MMA)-based polymer electrolytes showed that the MMA unit could improve the stability of the polymer electrolyte toward the Li electrode, which is probably due to the enhanced adhesion of the polymer electrolyte to the Li electrode. Received: 14 July 1997 / Accepted: 14 May 1998     

STUDIES OF THE CRYSTALLIZATION BEHAVIOR IN THE CRYSTALLINE/AMORPHOUS POLYMER BLENDS: POLY(ETHYLENE OXIDE)/POLY(METHYL METHACRYLATE) AND POLY(ETHYLENE OXIDE)/POLY(VINYL ACETATE)

The crystallization process of poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA)and PEO/poly(vinyl acetate) (PVAc) blends has been characterized by Fourier Transform Infrared(FTIR) spectra in conjunction with Differential Scanning Calorimeter (DSC) measurements. Thecrystallinity of PEO varies consistently with PEO content in PEO/PVAc blends and the PEO/PMMAblends containing 50 wt% or less PMMA. For the PEO/PMMA blends containing 60 wt% ormore PMMA, the crystallinity of PEO decreases more than PEO content but develops with crystal-lization time. These results can be explained in terms of difference between the crystallization tem-perature (T_c) and glass transition temperature (T_g) of the blends as a function of content of amorphouscomponent.     

Effect of nanoscale CeO<Subscript>2</Subscript> on PVDF-HFP-based nanocomposite porous polymer electrolytes for Li-ion batteries

New poly (vinylidenefluoride-co-hexafluoro propylene) (PVDF-HFP)/CeO₂-based microcomposite porous polymer membranes (MCPPM) and nanocomposite porous polymer membranes (NCPPM) were prepared by phase inversion technique using N-methyl 2-pyrrolidone (NMP) as a solvent and deionized water as a nonsolvent. Phase inversion occurred on the MCPPM/NCPPM when it is treated by deionized water (nonsolvent). Microcomposite porous polymer electrolytes (MCPPE) and nanocomposite porous polymer electrolytes (NCPPE) were obtained from their composite porous polymer membranes when immersed in 1.0 M LiClO₄ in a mixture of ethylene carbonate/dimethyl carbonate (EC/DMC) (v/v = 1:1) electrolyte solution. The structure and porous morphology of both composite porous polymer membranes was examined by scanning electron microscope (SEM) analysis. Thermal behavior of both MCPPM/NCPPM was investigated from DSC analysis. Optimized filler (8 wt% CeO₂) added to the NCPPM increases the porosity (72%) than MCPPM (59%). The results showed that the NCPPE has high electrolyte solution uptake (150%) and maximum ionic conductivity value of 2.47 × 10⁻³ S cm⁻¹ at room temperature. The NCPPE (8 wt% CeO₂) between the lithium metal electrodes were found to have low interfacial resistance (760 Ω cm²) and wide electrochemical stability up to 4.7 V (vs Li/Li⁺) investigated by impedance spectra and linear sweep voltammetry (LSV), respectively. A prototype battery, which consists of NCPPE between the graphite anode and LiCoO₂ cathode, proves good cycling performance at a discharge rate of C/2 for Li-ion polymer batteries.     

Synthesis and characterization of a new network polymer electrolyte containing polyether in the main chains and side chains

A new network polymer electrolyte matrix with polyether in the side chains and main chains was synthesized by the azo-macroinitiator method and urethane reaction. The macroinitiator, polymer and network polymer were confirmed by Fourier-transform infrared (FT-IR) spectroscopy and ¹H NMR. FT-IR was also used to study the environment of lithium ions doped in these network polymer electrolytes. Three important groups are considered: N-H, carbonyl, and ether groups. The thermal properties of the polymer electrolytes were measured by differential scanning calorimetry and thermogravimetric analysis. The T_g value of this polymer is less than that of a general comb-like polymer. Added lithium ions interact with the oxygen atoms on ether groups, causing the T_g of the polymer electrolyte to increase. Moreover, the interaction between lithium ions and ether groups decreases the decomposition temperature of the polymer. The conductivity measured by AC impedance reached a maximum of 10⁻⁴ S cm⁻¹. A plot of conductivity vs. temperature fit the Vogel-Tamman-Fulcher equation, indicating that ionic mobility in this network polymer electrolyte is coupled to segmental chain movements.     

A Perovskite Electrolyte That Is Stable in Moist Air for Lithium‐Ion Batteries

Solid‐oxide Li⁺ electrolytes of a rechargeable cell are generally sensitive to moisture in the air as H⁺ exchanges for the mobile Li⁺ of the electrolyte and forms insulating surface phases at the electrolyte interfaces and in the grain boundaries of a polycrystalline membrane. These surface phases dominate the total interfacial resistance of a conventional rechargeable cell with a solid–electrolyte separator. We report a new perovskite Li⁺ solid electrolyte, Li_0.38Sr_0.44Ta_0.7Hf_0.3O_2.95F_0.05, with a lithium‐ion conductivity of σ_Li=4.8×10^?4 S cm^?1 at 25 °C that does not react with water having 3≤pH≤14. The solid electrolyte with a thin Li⁺‐conducting polymer on its surface to prevent reduction of Ta⁵⁺ is wet by metallic lithium and provides low‐impedance dendrite‐free plating/stripping of a lithium anode. It is also stable upon contact with a composite polymer cathode. With this solid electrolyte, we demonstrate excellent cycling performance of an all‐solid‐state Li/LiFePO₄ cell, a Li‐S cell with a polymer‐gel cathode, and a supercapacitor.