Origin of visible-light-driven photocatalysis: A comparative study on N/F-doped and N-F-codoped TiO2 powders by means of experimental characterizations and theoretical calculations

An overall comparative study was carried out on N-doped, F-doped, and N-F-codoped TiO₂ powders (NTO, FTO, NFTO) synthesized by spray pyrolysis in order to elucidate the origin of their visible-light-driven photocatalysis. The comparisons in their experimentally obtained characteristics were based on the analysis of XPS, UV-Vis, PL, NH₃-TPD and ESR spectra. The comparisons in their theoretically predicted properties were based on the analysis of the calculated electronic structures. As the results, N-doping into TiO₂ resulted in not only the improvement in visible-light absorption but also the creation of surface oxygen vacancies. F-doping produced several beneficial effects including the creation of surface oxygen vacancies, the enhancement of surface acidity and the increase of Ti³⁺ ions. Doped N atoms formed a localized energy state above the valence band of TiO₂, whereas doped F atoms themselves had no influence on the band structure. The photocatalytic tests indicated that the NFTO demonstrated the highest visible-light activity for decompositions of both acetaldehyde and trichloroethylene. This high activity was ascribed to a synergetic consequence of several beneficial effects induced by the N-F-codoping.     

The preparation and characterization of La doped TiO2 nanoparticles and their photocatalytic activity

In this paper, pure and La doped TiO₂ nanoparticles with different La content were prepared by a sol-gel process using Ti (OC₄H₉)₄ as raw material, and also were characterized by XRD, TG-DTA, TEM, XPS, DRS and Photoluminescence (PL) spectra. We mainly investigated the effects of calcining temperature and La content on the properties and the photocatalytic activity for degrading phenol of as-prepared TiO₂ samples, and also discussed the relationships between PL spectra and photocatalytic activity as well as the mechanisms of La doping on TiO₂ phase transformation. The results showed that La³⁺ did not enter into the crystal lattices of TiO₂ and was uniformly dispersed onto TiO₂ as the form of La₂O₃ particles with small size, which possibly made La dopant have a great inhibition on TiO₂ phase transformation; La dopant did not give rise to a new PL signal, but it could improve the intensity of PL spectra with a appropriate La content, which was possibly attributed to the increase in the content of surface oxygen vacancies and defects after doping La; La doped TiO₂ nanoparticles calcined at 600°C exhibited higher photocatalytic activity, indicating that 600°C was an appropriate calcination temperature. The order of photocatalytic activity of La doped TiO₂ samples with different La content was as following: 1>1.5>3>0.5>5>0 mol%, which was the same as the order of their PL intensity, namely, the stronger the PL intensity, the higher the photocatalytic activity, demonstrating that there were certain relationships between PL spectra and photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions.     

Mesoporous interstitial and substitutional nitrogen-containing titanium dioxide photocatalysts prepared by acid-assisted sol–gel procedure

Two different types of nitrogen-containing TiO₂ were synthesized via an acid-modified sol–gel method. Yellow-colored interstitial and white substitutional nitrogen-containing TiO₂ powders were characterized by means of X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller specific surface area and Barrett–Joyner–Halenda pore size distribution analyses, scanning electron microscopy, transmission electron microscopy and UV–vis absorption spectroscopy. The band gaps of interstitial and substitutional nitrogen-containing TiO₂ ceramics were estimated from UV–vis spectroscopy data to be 2.6 and 2.8 eV, respectively. Prepared substitutional nitrogen-containing TiO₂ featured steep light absorption edge with an approximately parallel characteristic to that in pure TiO₂. This fact is due to band-to-band visible light absorption ability of substitutional nitrogen-containing TiO₂. The photocatalytic properties of the produced nitrogen-containing TiO₂ samples were compared for the degradation of Direct Red 28 azo dye. Further studies were also devised to compare the catalytic efficiency of the nitrogen-containing TiO₂ powders with the pure TiO₂ synthesized via the similar sol–gel method. The produced nitrogen-containing TiO₂ samples revealed superior photocatalytic properties in comparison with pure TiO₂ due to their remarkable band gap narrowing, surface oxygen vacancies and much more surface defects. The results also revealed that the substitutional nitrogen-containing TiO₂ is the most effective photocatalyst under ultraviolet and visible light irradiation.     

Vapor-thermal preparation of highly crystallized TiO2 powder and its photocatalytic activity

Nanocrystalline anatase TiO₂ powder photocatalysts were synthesized by a vapor-thermal method using tetrabutyl titanate as precursor at a temperature range from 120 to 200 °C. The as-synthesized products were characterized by X-ray diffraction, N₂ adsorption-desorption measurement, transmission electron microscopy, high resolution transmission electron microscopy, Fourier transform infrared spectra, Raman spectra, and their photocatalytic activity was evaluated by photocatalytic oxidation decomposition of acetone in air. The results showed that reaction temperature greatly affected the microstructures and photocatalytic activity of the samples. With increasing reaction temperature and time, the average crystalline size of TiO₂ particles increased and their crystallization enhanced, while the specific surface area of the products decreased. The TiO₂ powders obtained at a temperature range from 150 to 200 °C for 10 h showed good photocatalytic activity and were greatly higher than that of Degussa P-25.     

Effect of nitrogen-doping temperature on the structure and photocatalytic activity of the B,N-doped TiO2

B,N-TiO₂ photocatalysts were synthesized by boron doping firstly and subsequently nitrogen doping in NH₃ at variable temperatures. The effects of the nitrogen doping temperature on the structure and photocatalytic activity of the B,N-codoped TiO₂ were investigated. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis diffuse reflectance spectrum (DRS), electron paramagnetic resonance (EPR) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activity was evaluated with photocatalytic degradation of methyl orange dye (MO) under visible light and UV-visible light irradiation. The results suggested that the boron and nitrogen can be incorporated into the TiO₂ lattice either interstitially or substitutionally or both, while the Ti-O-B-N structure plays a vital role in photocatalytic activity in visible light region. The optimal nitrogen doping temperature is 550 °C. Higher temperature may form many oxygen vacancies and Ti³⁺ species, resulting in the decrease of photocatalytic activity in visible light.     

Effects of Calcination on the Physical and Photocatalytic Properties of TiO<Subscript>2</Subscript> Powders Prepared by Sol–Gel Template Method

TiO₂ powders were prepared by sol–gel template method and calcined under different conditions. XRD, BET and TEM were used to characterize the TiO₂ powders obtained. The photocatalytic activity of TiO₂ was investigated by the degradation of methyl orange. It was found that TiO₂ powder has the highest photocatalytic activity at a calcination temperature of 673 K. The effects of physical properties such as surface area, crystallinity and crystal phase on the photocatalytic activity of TiO₂ were discussed.     

Surface properties and photocatalytic activity of nanocrystalline titania films

In this work the efficiency and physicochemical details of a thin film produced by help of a microwave assisted sol gel technique is compared to different commercial powders (Degussa P25 and Hombikat UV100) deposited on glass substrates. Furthermore, a supercritical produced TiO₂ powder (SC 134) was included in the comparison.The prepared TiO₂ films were characterized using XRD, XPS, AFM, DSC and DLS. The photocatalytic activity was determined using stearic acid as a model compound. Investigation of the prepared films showed that the Degussa P25 film and the sol–gel film were the most photocatalytic active films. The activity of the films was found to be related to the crystallinity of the TiO₂ film and the amount of surface area and surface hydroxyl groups. Based on the XPS investigation of the films before and after UV irradiation it was suggested that the photocatalytic destruction of organic matter on TiO₂ films proceeds partly through formation of hydroxyl radicals which are formed from surface hydroxyl groups created by interactions between adsorbed water and vacancies on the TiO₂ surface. Furthermore a correlation between the amount of OH groups on the surface of the different TiO₂ films and the photocatalytic activity was found.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

Controlled crystal phase and particle size of loaded-TiO2 using clinoptilolite as support via hydrothermal method for degradation of crystal violet dye in aqueous solution

TiO₂-supported clinoptilolites (TiO₂/clinoptilolites) were successfully synthesized with controlled crystal phase and particle size via hydrothermal method to enhance photocatalytic performance of TiO₂. The effects of various parameters including temperature, acidity and concentration of Ti-containing solutions on the particle size, crystal phase and agglomeration of TiO₂ supported on clinoptilolite were investigated thoroughly by characterizations of X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscope (SEM), transmission electron microscope (TEM), BET isotherm, UV–visible (UV–vis) spectrophotometer and Malvern zetasizer. The results demonstrate that increasing temperature and strengthen acidity are beneficial to enhance the crystallinity and particle size of supported TiO₂. Increase in acidity also leads to more uniform distribution of TiO₂ on the surface of clinoptilolite. The TiO₂ nano-crystals deposited on the surface of clinoptilolite, exhibit rutile or anatase phase, strongly depending on the preparation procedure. The resultant TiO₂/clinoptilolites could be used as photo-catalysts for the degradation of crystal violet (CV) dye in aqueous solution, showing a higher photo-catalytic activity with 89% degradation within 100 min. The effect of operational parameters, such as pH values of reaction media, dose of used catalyst, and concentration of CV dye on the CV degradation performance were investigated, in which the kinetics of CV dye degradation was found to follow the pseudo-first order kinetic model.     

金红石相TiO2纳米棒的氢化处理及其光催化活性

以钛酸四丁酯为钛源,通过盐酸调制的水热法制备出了具有棒状结构的金红石相纳米TiO₂,并进一步进行高温氢化处理. 采用X射线衍射（XRD）,透射电镜（TEM）,紫外-可见-近红外漫反射（UV-Vis-NIR DRS）,电子顺磁共振（EPR）和表面光伏（SPS）等测试手段对样品进行表征,以气相乙醛和液相苯酚为目标污染物考察催化剂的光催化活性. 结果表明：随着高温氢化处理时间的延长,TiO₂样品的可见光吸收逐渐增强,其颜色逐渐由白色转变成灰色,这主要与引入的Ti³⁺/氧空位缺陷有关. 表面光电压谱和羟基自由基测试表明,适当时间的氢化处理有利于光生电荷的分离. 在光催化氧化降解气相乙醛和液相苯酚过程中,经适当时间氢化处理的样品表现出高的可见光催化活性. 并且可见光催化活性的规律与紫外光下的是一致的. 这是因为氢化处理后在导带底下方引入了缺陷能级,拓展了可见光响应. 过度的氢化处理会在TiO₂导带下方引入较低的缺陷能级,使光生电荷的复合加剧,导致光催化活性降低.     

Building surface defects by doping with transition metal on ultrafine TiO2 to enhance the photocatalytic H2 production activity

Inefficient charge separation and limited light absorption are two critical issues associated with high-efficiency photocatalytic H₂ production using TiO₂. Surface defects within a certain concentration range in photocatalyst materials are beneficial for photocatalytic activity. In this study, surface defects (oxygen vacancies and metal cation replacement defects) were induced with a facile and effective approach by surface doping with low-cost transition metals (Co, Ni, Cu, and Mn) on ultrafine TiO₂. The obtained surface-defective TiO₂ exhibited a 3–4-fold improved activity compared to that of the original ultrafine TiO_2. In addition, a H₂ production rate of 3.4 μmol/h was obtained using visible light (λ > 420 nm) irradiation. The apparent quantum yield (AQY) at 365 nm reached 36.9% over TiO₂-Cu, significantly more than the commercial P25 TiO₂. The enhancement of photocatalytic H₂ production activity can be attributed to improved rapid charge separation efficiency and expanded light absorption window. This hydrothermal treatment with transition metal was proven to be a very facile and effective method for obtaining surface defects.     

Characterization, activity and mechanisms of a visible light driven photocatalyst: Manganese and iron co-modified TiO2 nanoparticles

An attempt was made to prepare Mn,Fe-codoped nanostructured TiO₂ photocatalyst for visible light assisted degradation of an azo dye (methylene blue) in aqueous solutions by a sol-gel process. The asprepared nanoparticles were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS) and photoluminescence spectra (PL) techniques. The photocatalytic activity of Mn,Fe-codoped TiO₂ catalyst was evaluated by measuring degradation rates of methylene blue (MB) under visible light. The results showed that doping with the manganese and iron ions significantly enhanced the photocatalytic activity for MB degradation under visible light irradiation. This was ascribed to the fact that a small amount of manganese and iron dopants simultaneously increased MB adsorption capacity and separation efficiency of electron-hole pairs. The results of DRS showed that Mn,Fe-codoped TiO₂ had significant absorption between 400 and 500 nm, which increased with the increase of manganese ion content. It is found that the stronger the PL intensity, the higher the photocatalytic activity. This could be explained by the points that PL spectra mainly resulted from surface oxygen vacancies and defects during the process of PL, while surface oxygen vacancies and defects could be favorable in capturing the photoinduced electrons during the process of photocatalytic reactions, so that the recombination of photoinduced electrons and holes could be effectively inhibited.     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

熔融盐法制备富氧空位TiO2纳米片及其光催化性能

氧空位缺陷对半导体材料性能的积极作用引起人们越来越多的关注。本文中,以TiCl4在三氟乙酸中的水解产物为前驱体,通过一步熔融盐法成功合成了具有富氧空位的蓝色TiO2纳米片。由于熔融盐低的氧分压,使前驱体在煅烧过程中消耗了TiO2中的晶格氧从而产生大量的氧空位和Ti3+。紫外-可见漫反射光谱测试表明,蓝色TiO2纳米片的带隙宽度减小至2.69eV,光吸收范围从紫外光区拓宽到可见光区。所制备的蓝色TiO2纳米片表现出优异的光催化活性,在全光谱照射下,对若丹明B的光降解速率是纯TiO2的47.3倍。同时,形成的晶格氟掺杂能有效地稳定氧空位,极大地提高了光生载流子的分离效率。本工作为在半导体氧化物材料内构建氧空位提供了新的思路。     

The Influence of Defects on Mo‐Doped TiO2 by First‐Principles Studies

TiO₂ doped with transition metals shows improved photocatalytic efficiency. Herein the electronic and optical properties of Mo‐doped TiO₂ with defects are investigated by DFT calculations. For both rutile and anatase phases of TiO₂, the bandgap decreases continuously with increasing Mo doping level. The 4d electrons of Mo introduce localized states into the forbidden band of TiO₂, and this shifts the absorption edge into the visible‐light region and enhances the photocatalytic activity. Since defects are universally distributed in TiO₂ or doped TiO₂, the effect of oxygen deficiency due to oxygen vacancies or interstitial Mo atoms is systemically studied. Oxygen vacancies associated with the Mo dopant atoms or interstitial Mo will reduce the spin polarization and magnetic moment of Mo‐doped TiO₂. Moreover, oxygen deficiency has a negative impact on the improved photocatalytic activity of Mo‐doped TiO₂. The current results indicate that substitutional Mo, interstitial Mo, and oxygen vacancy have different impacts on the electronic/optical properties of TiO₂ and are suited to different applications.     

A sol–gel combustion synthesis method for TiO<Subscript>2</Subscript> powders with enhanced photocatalytic activity

TiO₂ photocatalytic powders were synthesized by a sol–gel combustion synthesis method in which urea was used as the fuel and titanyl nitrate was used as the oxidizer. Various fuel-to-oxidizer ratios were studied for their effects on the combustion phenomena and the properties of the synthesized TiO₂. The fuel-to-oxidizer ratio was found to determine the maximum combustion temperature, which in turn affects the specific surface area, crystallite size, and weight fraction of anatase phase of the synthesized TiO₂. The synthesized TiO₂ all contain carbonaceous species and are either pure anatase or anatase–rutile mixed phase in crystalline structure. The photocatalytic activity of the TiO₂ was found to correlate to a certain degree with the specific surface area, crystallite size, weight fraction of anatase phase, and visible and IR absorbances. The mixed phase TiO₂ shows a higher photocatalytic activity than the pure anatase phase TiO₂ when containing a small fraction (<~25 wt%) of rutile phase but a lower phoyocatalytic activity when containing a large fraction (>~25 wt%) of rutile phase. The synthesized TiO₂ all show higher photocatalytic activity than Degussa P25 TiO₂. The enhanced photocatalytic activity was attributed mainly to sensitization by the carbonaceous species and larger amounts of hydroxyl group adsorbed on the TiO₂ surface.     

Correlation of the Catalytic Activity for Oxidation Taking Place on Various TiO2 Surfaces with Surface OH Groups and Surface Oxygen Vacancies

Three catalytic oxidation reactions have been studied: The ultraviolet (UV) light induced photocatalytic decomposition of the synthetic dye sulforhodamine B (SRB) in the presence of TiO₂ nanostructures in water, together with two reactions employing Au/TiO₂ nanostructure catalysts, namely, CO oxidation in air and the decomposition of formaldehyde under visible light irradiation. Four kinds of TiO₂ nanotubes and nanorods with different phases and compositions were prepared for this study, and gold nanoparticle (Au‐NP) catalysts were supported on some of these TiO₂ nanostructures (to form Au/TiO₂ catalysts). FTIR emission spectroscopy (IES) measurements provided evidence that the order of the surface OH regeneration ability of the four types of TiO₂ nanostructures studied gave the same trend as the catalytic activities of the TiO₂ nanostructures or their respective Au/TiO₂ catalysts for the three oxidation reactions. Both IES and X‐ray photoelectron spectroscopy (XPS) proved that anatase TiO₂ had the strongest OH regeneration ability among the four types of TiO₂ phases or compositions. Based on these results, a model for the surface OH group generation, absorption, and activation of molecular oxygen has been proposed: The oxygen vacancies at the bridging O^2? sites on TiO₂ surfaces dissociatively absorb water molecules to form OH groups that facilitate adsorption and activation of O₂ molecules in nearby oxygen vacancies by lowering the absorption energy of molecular O₂. A new mechanism for the photocatalytic formaldehyde decomposition with the Au/TiO₂ catalysts is also proposed, based on the photocatalytic activity of the Au‐NPs under visible light. The Au‐NPs absorb the light owing to the surface plasmon resonance effect and mediate the electron transfers that the reaction needs.     

Synthesis and photocatalytic activity for water-splitting reaction of nanocrystalline mesoporous titania prepared by hydrothermal method

Nanocrystalline mesoporous TiO₂ was synthesized by hydrothermal method using titanium butoxide as starting material. XRD, SEM, and TEM analyses revealed that the synthesized TiO₂ had anatase structure with crystalline size of about 8 nm. Moreover, the synthesized titania possessed a narrow pore size distribution with average pore diameter and high specific surface area of 215 m²/g. The photocatalytic activity of synthesized TiO₂ was evaluated with photocatalytic H₂ production from water-splitting reaction. The photocatalytic activity of synthesized TiO₂ treated with appropriate calcination temperature was considerably higher than that of commercial TiO₂ (Ishihara ST-01). The utilization of mesoporous TiO₂ photocatalyst with high crystallinity of anatase phase promoted great H₂ production. Furthermore, the reaction temperature significantly influences the water-splitting reaction.     

Facile preparation of visible-light-sensitive sulfur–nitrogen-codoped titanium dioxide

S–N-codoped TiO₂ powders have been synthesized through a facile one-step sol–gel method by using tetrabutyltitanate and thiourea as precursors. The S–N-codoped TiO₂ treated at 500 °C showed the highest photocatalytic activity for degrading methylene blue under visible light irradiation. XRD, XPS and UV–vis studies revealed that the high visible-light photocatalytic activity of the doped TiO₂ may originate from the synergetic effect of sulfur and nitrogen codoping into TiO₂.     

Microwave‐Hydrothermal Preparation and Visible‐Light Photoactivity of Plasmonic Photocatalyst Ag‐TiO2 Nanocomposite Hollow Spheres

Visible‐light‐driven plasmonic photocatalyst Ag‐TiO₂ nanocomposite hollow spheres are prepared by a template‐free chemically‐induced self‐transformation strategy under microwave‐hydrothermal conditions, followed by a photochemical reduction process under xenon lamp irradiation. The prepared samples are characterized by using scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, N₂ adsorption‐desorption isotherms, X‐ray photoelectron spectroscopy, UV/Vis and Raman spectroscopy. Production of ?OH radicals on the surface of visible‐light illuminated TiO₂ was detected by using a photoluminescence method with terephthalic acid as the probe molecule. The photocatalytic activity of as‐prepared samples was evaluated by photocatalytic decolorization of Rhodamine B (RhB) aqueous solution at ambient temperature under visible‐light irradiation. The results show that the surface plasmon absorption band of the silver nanoparticles supported on the TiO₂ hollow spheres was red shifted, and a strong surface enhanced Raman scattering effect for the Ag‐TiO₂ nanocomposite sample was observed. The prepared nanocomposite hollow spheres exhibits a highly visible‐light photocatalytic activity for photocatalytic degradation of RhB in water, and their photocatalytic activity is higher than that of pure TiO₂ and commercial Degussa P25 (P25) powders. Especially, the as‐prepared Ag‐TiO₂ nanocomposite hollow spheres at the nominal atomic ratio of silver to titanium ( R ) of 2 showed the highest photocatalytic activity, which exceeds that of P25 by a factor of more than 2.