Temperature and concentration quenching of mid-IR photoluminescence in iron doped ZnSe and ZnS laser crystals

Concentration dependences of the mid-IR kinetic of luminescence at ⁵E?⁵T₂ transition in Fe:ZnSe and Fe:ZnS laser samples were studied in 14–300 K temperature ranges. Radiation lifetime in Fe:ZnSe samples measured using low doped samples with iron concentration 0.1×10¹⁸ cm^?3 was estimated to be 57 μs. The magnetic susceptibility for higher doped (C_Fe=38 and 112×10¹⁸ cm^?3) Fe:ZnSe samples was found to consist of a paramagnetic Curie–Weiss behavior arising from the weakly interacting Fe²⁺ ions and a diamagnetic ZnSe contribution plus a temperature-independent, field-dependent contribution possibly arising from very small amounts of aggregated Fe.     

Effect of Li-substitution on piezoelectric and ferroelectric properties of (Bi0.92Na0.92−xLix)0.5Ba0.06Sr0.02TiO3 lead-free ceramics

New lead-free ceramics (Bi_0.92Na_0.92−xLi_x)_0.5Ba_0.06Sr_0.02TiO₃ have been fabricated by a conventional ceramic technique and their electrical properties have been studied. X-ray diffraction studies reveal that Li⁺, Ba²⁺ and Sr²⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure. The partial substitution of Li⁺ for Na⁺ increases the remanent polarization P_r of the ceramics. Because of the large P_r and low coercive field E_c, the ceramics with x = 0.075–0.125 exhibit excellent piezoelectric properties: d₃₃ = 189–235 pC/N, k_p = 33.6–36.3% and k_t = 51.6–54.3%. The ceramics exhibit relaxor behaviors after the substitution of Li⁺ for Na⁺. Our results also suggest that polar and non-polar phases may coexist in the ceramics at temperatures above the depolarization temperature T_d.     

Structural and electrochemical properties of layered lithium nitridocuprates Li3 − xCuxN

We report a systematic study of the layered lithium nitridocuprates Li_3 ? xCu_xN with 0.1 ≤ x ≤ 0.39. The structural data obtained from experimental XRD patterns, Rietveld refinements and unit cell parameters calculation vs x, indicate that copper (I) substitute interlayer lithium ions in the parent nitride Li₃N to form the Li_3 ? xCu_xN compound without any Li vacancy in the Li₂N^? layer. Electrochemical results report Li insertion into the corresponding layered structures cannot take place in the 1.2/0.02 V voltage range as in the case of lithium into nitridonickelates and nitridocobaltates. However, in the initial charge process of Li_3 ? xCu_xN at 1.4 V leading to a specific capacity higher than 1000 mA h/g, the oxidation of copper and nitride ions is probably involved inducing a strong structural disordering process. As a consequence a new rechargeable electrochemical system characterized by discharge–charge potential of ≈ 0.3 V/1.2 V appears from the second cycle. Cycling experiments 0.02 V voltage/0.02 V range induce a complete destruction of the layered host lattice and the presence of Cu₃N in the charge state suggests a conversion reaction. The capacity recovered in the 1.4/0.02 V range practically stabilizes around 500 mA h/g after 20 cycles.     

Electro-optic coefficients of a non-congruent lithium niobate fabricated by vapour transport equilibration: Composition effect

Composition effect on electro-optic (EO) properties of a LiNbO₃ (LN) single-crystal has been investigated in a Li₂O-content range of 47.0–49.95 mol%. Some non-congruent LN crystals with different Li₂O-contents were prepared by performing Li-deficient or Li-rich vapour transport equilibration treatments on as-grown congruent LN crystals. Unclamped EO coefficients γ₁₃ and γ₃₃ of these samples were measured by a Mach–Zehnder interferometric method. The measurements show that in the Li-deficient regime both γ₁₃ and γ₃₃ increase by ～8% as Li₂O-content decreases from the congruent 48.6 mol% to the 47.0 mol% in the Li-deficient regime. The feature is desired for the EO application of the Li-deficient crystal. In the near-stoichiometric regime, both γ₁₃ and γ₃₃ reveal a non-monotonic dependence. As the Li₂O-content increases from the 48.6 mol%, the EO coefficient decreases. Around Li₂O-content 49.5 mol%, a minimum is reached. After that, the EO coefficient recovers slowly. At the stoichiometric composition, it recovers to a value close to that at the congruent point. Comparison shows that different crystal growth methods give rise to different defect structure features and hence different composition effects.     

Lithium naphthalocyanine as a new molecular radical probe for electron paramagnetic resonance oximetry

A new lithium naphthalocyanine dye aggregate [Li₂Nc][LiNc] is reported as a potential electron paramagnetic resonance (EPR) oximetry probe for accurate measurement of oxygen concentration in biological systems. The Li₂Nc is diamagnetic; however, the LiNc molecule has an unpaired electron and hence is paramagnetic. The aggregate shows a strong and single line EPR signal that is non-saturating at normal EPR power levels. An oxygen-dependent peak-to-peak EPR spectral width ranging from 0.51 G (at pO₂: 0 mmHg) to 26.2 G (at pO₂: 760 mmHg) has been observed. The application of this probe has been demonstrated in the measurement of arterial and venous oxygen tensions in a rat.     

Ho:LaF3 single crystal as potential material for 2 μm and 2.9 μm lasers

Optical properties of a Ho-doped LaF₃ single crystal have been detailed investigated as a promising material for 2 μm and 2.9 μm lasers for the first time. Judd–Ofelt theory was applied to analyze the absorption spectrum to determine the J–O intensity parameters Ω_t(t=2,4,6), based on which the emission probabilities, branching ratio and radiative lifetime for the as-grown crystal were all calculated. The stimulated emission cross-sections of the ⁵I₇ → ⁵I₈ and ⁵I₆ → ⁵I₇ transitions were obtained by using the Fuchtbauer–Ladenburg method. The gain cross-section for 2 μm emission becomes positive once the population inversion level reaches 30%. The Ho:LaF₃ crystal shows long fluorescence lifetime of ⁵I₇ manifold (25.81 ms) as well as ⁵I₆ manifold (10.37 ms) compared with other Ho³⁺-doped crystals. It can be proposed that the Ho:LaF₃ crystal may be a promising material for 2 μm and 2.9 μm laser applications.     

Photo-luminescence properties of Cu and Ag doped Li2B4O7 single crystals at low temperatures

UV excited photo luminescence from Li₂B₄O₇:Cu and Li₂B₄O₇:Cu, Ag single crystals has been investigated in the temperature range from 77 K to 300 K. An excitation band having a doublet structure at 240 nm and 262 nm was observed for the emission at 370 nm that corresponds to ¹A_1g→¹E_g and ¹A_1g→¹T_2g crystal field components of the 3d¹⁰→3d⁹4s¹ transition of Cu⁺. The relative intensity of these components and their temperature dependence provide a measure of the off-center displacement of the Cu⁺ ground state in the crystal lattice site. The co-doped Ag plays a role of a sensitizer when doped with Cu and increases the overall emission as the emission between Ag states lies in the excitation region of Cu states. The 370 nm emission in both the crystals slightly decreases with temperature; however a sudden increase in the intensity around 264 K was observed.     

UV–visible absorption spectrum determination of optical energy gaps of α and β lithium nitrides

It is well known that a high pressure can induce α–β phase transformation of lithium nitride (Li₃N). However, this work demonstrated that a reverse phase transformation of Li₃N from β to α could occur when it was subjected to heat-treatment at 500 °C in vacuum. Furthermore, the optical properties of α and β lithium nitrides were evaluated by UV–visible spectra. The optical energy gaps (E_g) of α and β lithium nitrides, which were determined from the derivative UV–visible spectra, are 1.81±0.01 and 2.14±0.01 eV, respectively.     

White-light generation through Ce3+/Mn2+-codoped and Eu2+-doped Ba1.2Ca0.8SiO4 T-phase phosphors

Hexagonal Ba_1.20Ca_0.8?2x?ySiO₄:xCe³⁺,xLi⁺,yMn²⁺ phosphors exhibit two emission bands peaking near 400 and 600 nm from the allowed f–d transition of Ce³⁺ ions and the forbidden ⁴T₁–⁶A₁ transition of Mn²⁺ ions, respectively. The strong interaction between Ce³⁺/Mn²⁺ ions is investigated in terms of energy transfer, crystal field effect, and microstructure by varying their concentrations. They show a higher quenching temperature of 250 °C than that of a commercially used (Ba,Sr)₂SiO₄:Eu²⁺ phosphor (150 °C). Finally, mixtures of these phosphors with green-emissive Ba_1.20Ca_0.70SiO₄:0.10Eu²⁺ are tested and yielded correlated color temperatures from 3500 to 7000 K, and color rendering indices up to 95%.     

Optical spectroscopy and laser parameters of Zn2+/Er3+/Yb3+-tridoped LiNbO3 crystal

The Zn/Er/Yb:LiNbO₃ and Er/Yb:LiNbO₃ crystals were grown by the Czochralski technique. The laser characteristics of 1.54 μm emission were predicted based on the Judd–Ofelt theory, and the intensity parameters Ω_t (Ω₂=7.23×10^?20 cm², Ω₄=3.15×10^?20 cm² and Ω₆=1.43×10^?20 cm²) were obtained. The stimulated emission cross sections (σ_em) at 1.54 μm emission in Zn/Er/Yb:LiNbO₃ were calculated based on the McCumber theory and the Füchtbauer–Ladenburg theory. The gain cross section spectrum of Zn/Er/Yb:LiNbO₃ crystal was also investigated. Under 980 nm excitation, a lenghthening lifetime of 1.54 μm emission and an enhancement of green upconversion emission were observed for Zn/Er/Yb:LiNbO₃ crystal. The studies on the power pump dependence and the upconversion mechanism suggested that both green and red upconversion emissions were populated via the three-photon process, and Zn²⁺ ion tridoping increases the probability of cross relaxation process between the two neighboring Er³⁺ ions.     

Luminescence of Eu2+–vc− dipoles and their associates in CsI:Eu crystals

Spectral-kinetics properties of photo-scintillation excited with single light pulses of a nitrogen laser (λ=337.1 nm, t_1/2=5 ns, Q=1 mJ) have been studied in CsI:Eu crystals at temperature within 80–300 K. It is found that the exponential decay of 463 nm emission band has a time constant which grows from 0.85 μs at 78 K to 1.6 μs at 380 K. Such an anomalous temperature behavior of 463 nm emission decay kinetics is discussed in terms of the crystal thermal expansion. It has been proposed that 463 nm emission is caused by a cluster center consisting of three dipoles Eu²⁺v_c^? bounded with each other in a hexagon. Owing to the exchange resonance in the cluster, the energy passes from an excited dipole to a non-excited one and the distance between them gets longer due to thermal expansion of the crystal.     

The photoluminescence properties of TiO2-sheathed ZnSe nanowires

ZnSe nanowires have been synthesized by thermal evaporation of ZnSe powders on gold-coated Al₂O₃(0 0 0 1) substrates and then sheathed with TiO₂ by sputtering. Our results show that sheathing Zn nanowires with thin TiO₂ layers can significantly enhance the photoluminescence (PL) emission intensity. XPS analysis results suggest that the PL enhancement is attributed to increases in the concentrations of deep levels such as oxygen and titanium interstitials as well as the density of interface states. The PL emission of ZnSe nanowires is also enhanced by thermal annealing. Annealing in an argon atmosphere is more efficient in enhancing the PL emission than annealing in an oxygen atmosphere.     

Structure dependent luminescence characterization of green–yellow emitting Sr2SiO4:Eu2+ phosphors for near UV LEDs

This paper reports on the luminescence properties of mixtures of α- and β-(Sr_0.97Eu_0.03)₂SiO₄ phosphors. These phosphors were prepared by 3 different synthesis techniques: a modified sol–gel/Pechini method, a co-precipitation method and a combustion method. The structural and optical properties of these phosphors were compared to those of solid state synthesized powders. The emission spectra consist of a weak broad blue band centered near 460 nm and a strong broad green–yellow band centered between 543 and 573 nm depending on the crystal structure. The green–yellow emission peak blue-shifts as the amount of β phase increases and the photoluminescence emission intensity and quantum efficiency of the mixed phase powders is greater than those of predominant α-phase powders when excited between 370 and 410 nm. Thus, (Sr_1?xEu_x)₂SiO₄ with larger proportion of the β phase are more promising candidates than single α-phase powders for use as a green–yellow emitting phosphor for near UV LED applications. Finally the phosphors prepared by the sol–gel/Pechini method, which have larger amount of β phase, have a higher emission intensity and quantum efficiency than those prepared by co-precipitation or combustion synthesis.     

Visible luminescence of nanocrystalline AlN:Er thin film by co-deposition of AlN,Er, and SiO2

We report a visible luminescence of Er³⁺ ions in an amorphous-nanocrystalline AlN:Er thin film prepared by co-deposition using AlN, Er, and SiO₂ targets. A PL emission spectrum of Er³⁺ in the AlN:Er film annealed at 750 °C showed a strong bluish green emission of Er³⁺ in the amorphous-nanocrystalline AlN:Er thin film, which is attributed to the intra-4fEr³⁺ transitions of ²H_11/2 → ⁴I_15/2 and ⁴F_7/2 → ⁴I_15/2. It was found that crystallite diameters were between 3 and 5 nm by high-resolution transmission electron microscopy. The occurrence of the strong Er³⁺ emission in the annealed AlN:Er thin film with a mixture of amorphous and nanocrystalline phases may be contributed to an increase in the number of excitation Er³⁺ centers and a presence of oxygen related to Er³⁺ excitation and recombination process in the AlN:Er thin film.     

Peculiarities of luminescent properties of cerium doped YAG transparent nanoceramics

Optical and luminescence properties of transparent nanosized cerium doped Y₃Al₅O₁₂ (YAG:Ce) ceramics have been studied. YAG:Ce nanoceramics were obtained by means of low temperature and high pressure (LTHP) sintering method. Nanoceramic samples were sintered in the 2–8 GPa pressure range, whereas Ce³⁺ concentration was varied in the 0.5–5 at. % range. It is shown that, in contrast to the single crystal, a strong rise of absorption coefficient was detected already at wavelength shorter than 400 nm in all nanoceramic samples studied. Furthermore, in nanoceramic samples unusual UV emission band near 3.1 eV was observed, which is not observed in the YAG:Ce single crystal. High pressure applied during nanoceramics sintering leads to significant changes in their optical and luminescence properties.     

Oxygen non-stoichiometry and electrical conductivity of Pr2−xSrxNiO4±δ with x = 0–0.5

Oxygen non-stoichiometry and electrical conductivity of the Pr_2−xSr_xNiO_4±δ series with x = 0.0–0.5 were investigated in Ar/O₂ (pO₂ = 2.5 to 21 000 Pa) within a temperature range of 20–1000 °C. The equilibrium values of oxygen non-stoichiometry and electrical conductivity of these nickelates were determined as functions of temperature and oxygen partial pressure (pO₂). The nickelates with x = 0–0.5 appear to be p-type semiconductors in the investigated temperature and pO₂ ranges. The nickelates with x = 0.3–0.5 show very feebly marked pO₂ dependencies of the conductivity. Pr_1.7Sr_0.3NiO_4±δ shows the anomalies of the conductivity versus oxygen partial pressure which can be related to the orthorhombic–tetragonal crystal structure transformations. The conductivity of the Pr_2−xSr_xNiO_4±δ samples correlates with the average oxidation state of the nickel cations. The samples with x = 0.5 have the highest nickel oxidation state (≈ 2.5+), the highest [Ni³⁺]/[Ni²⁺] ratio close to 1 and show the highest conductivity (≈ 120 S/cm) in the whole pO₂ and temperature ranges investigated.     

Characteristics of pulse plated CdxZn1−xSe films

Cd_xZn_1−xSe films (0 ⩽ x ⩽ 1) were deposited for the first time by the pulse plating technique at different duty cycles in the range 6–50% at room temperature from an aqueous bath containing zinc sulphate, cadmium sulphate and selenium oxide. To the author’s knowledge this is the first report on pulse plated Cd_xZn_1−xSe films. The deposition potential was −0.9 V (SCE). The as deposited films exhibited cubic structure. Composition of the films was estimated by Energy Dispersive Analysis of X-ray studies. X-ray photoelectron spectroscopy studies indicated the binding energies corresponding to Zn(2p_3/2), Cd(3d_5/2 and 3d_3/2) and Se(3d_5/2 and 3d_3/2). Optical band gap of the films varied from 1.72 to 2.70 eV as the composition varied from CdSe to ZnSe side. Atomic force microscopy studies indicated grain size in the range of 20–150 nm.     

Structure and magnetic properties of 300-nm-thick FePt films with Hf underlayer

Structure, microstructure, magnetic properties of 300-nm-thick FePt films with 10-nm-thick Hf underlayer have been studied. The experimental results showed that the very thin Hf underlayer could promote the ordering at reduced temperatures by facilitating the nucleation of the order phase, leading to refined grain size and magnetic domain size. Therefore, the permanent magnetic properties of FePt films were enhanced. (BH)_max and H_c of FePt films were greatly enhanced from 5.0–21.0 MGOe and 1.4–11.0 kOe for single layer to 10.2–23.6 MGOe and 4.5–13.2 kOe for Hf-underlayered films annealed in T_a region of 400–600 °C, respectively. Nevertheless, the severe interdiffusion between the Hf and FePt layers at T_a=800 °C resulted in the decreased S, coarsened surface morphology, grain and magnetic domain sizes, and therefore the slightly decreased (BH)_max to 18.0 MGOe.     

Crystal growth and structural properties of the spinel-type Li1 + xMn2 − xO4 (x = 0.10, 0.14)

Single crystals of the lithium-rich lithium manganese oxide spinels Li_1 + xMn_2 − xO₄ with x = 0.10 and 0.14 have been successfully synthesized in high-temperature molten chlorides at 1023 K. The single-crystal X-ray diffraction study confirmed the cubic Fd3¯m space group and the lattice parameters of a = 8.2401(9) Å for x = 0.10 and a = 8.2273(10) Å for x = 0.14 at 300 K, respectively. The crystal structures have been refined to the conventional values R = 3.7% for x = 0.10 and R = 3.1% for x = 0.14, respectively. Low-temperature single-crystal X-ray diffraction experiments revealed that these single crystal samples showed no phase transition between 100 and 300 K. The electron-density distribution images in these compounds by the single-crystal MEM analysis clearly showed strong covalent bonding features between the Mn and O atoms due to the Mn–3d and O–2p interaction.     

TL and OSL studies on lithium borate single crystals doped with Cu and Ag

Lithium borate (LBO) single crystals doped with Cu and Ag (0.25 mol% each) (Li₂B₄O₇:Cu,Ag) are grown by the Czochralski method. The thermoluminescence readout on Li₂B₄O₇:Cu,Ag crystals showed three glow peaks at～375, 441 and 516 K for the heating rate of 1  K/s. The thermoluminescence sensitivity of the grown Li₂B₄O₇:Cu,Ag single crystals is found to be 5 times TLD-100 and a linear dose response in the range 1 mGy to 1 kGy. The glow curve deconvolution reveals nearly first order kinetics for all the three peaks with trap depths 0.77, 1.25 and 1.34 eV respectively and corresponding frequency factors 1.6×10⁹, 1.3×10¹³ and 6.8×10¹¹ s^?1. The continuous wave optically stimulated luminescence (CW-OSL) measurements were performed on the LBO:Cu,Ag single crystals using blue light stimulation. The traps responsible for the three thermoluminescence peaks in Li₂B₄O₇:Cu,Ag are found to be OSL sensitive. The qualitative correlation between TL peaks and CW-OSL response is established. The photoluminescence studies show that in case of co-doping of Ag in LBO:Cu the emission at 370 nm in Cu states dominates over the transitions in Ag states implying doping of Ag plays a role as sensitizer when co-doped with Cu and increases overall emission.