Experimental Investigation on Mechanical Behavior of Coarse Marble Under Six Different Loading Paths

A series of triaxial compression experiments were preformed for the coarse marble samples under different loading paths by the rock mechanics servo-controlled testing system. Based on the experimental results of complete stress-strain curves, the influence of loading path on the strength and deformation failure behavior of coarse marble is made a detailed analysis. Three loading paths (Paths I–III) are put forward to confirm the strength parameters (cohesion and internal friction angle) of coarse marble in accordance with linear Mohr-Coulomb criterion. Compared among the strength parameters, two loading paths (i.e. Path II by stepping up the confining pressure and Path III by reducing the confining pressure after peak strength) are suggested to confirm the triaxial strengths of rock under different confining pressures by only one sample, which is very applicable for a kind of rock that has obvious plastic and ductile deformation behavior (e.g. marble, chalk, mudstone, etc.). In order to investigate re-fracture mechanical behavior of rock material, three loading paths (Paths IV–VI) are also put forward for flawed coarse marble. The peak strength and deformation failure mode of flawed coarse marble are found depending on the loading paths (Paths IV–VI). Under lower confining pressures, the peak strength and Young’s modulus of damage sample (compressed until post-peak stress under higher confining pressure) are all lower compared with that of flawed sample; moreover mechanical parameter of damage sample is lower for the larger compressed post-peak plastic deformation of coarse marble. However under higher confining pressures (e.g. σ ₃?=?30 MPa), the axial supporting capacity and elastic modulus of damage coarse marble (compressed until post-peak stress under lower confining pressure) is not related to the loading path, while the deformation modulus and peak strain of damage sample depend on the difference of initial confining pressure and post-peak plastic deformation. The friction among crystal grains determines the strength behavior of flawed coarse marble under various loading paths. In the end, the effect of loading path on failure mode of intact and flawed coarse marble is also investigated. The present research provides increased understanding of the fundamental nature of rock failure under different loading paths.     

Experimental investigation on strength and failure behavior of pre-cracked marble under conventional triaxial compression

Fractures in natural rocks have an important effect on the strength and failure behavior of rock mass, which are often evaluated in rock engineering practice. The theoretical evaluation of mechanical behavior of fractured rock mass has no satisfactory answer due to the role of confining pressure and crack geometry. Therefore, in this paper, conventional triaxial compression experiments were carried out to study the strength and failure behavior of marble samples with two pre-existing closed cracks in non-overlapping geometry. Based on the experimental results of a number of triaxial compression tests, the effect of crack coalescence on the axial supporting capacity and deformation property were investigated with different confining pressures. The results show that intact samples and flawed samples (marble with pre-existing cracks) have different deformation properties after peak stress, which change from brittleness to plasticity and ductility with the increase of confining pressure. The peak strength and failure mode are found depending not only on the geometry of flaw, but also on the confining pressure. The strength of flawed samples shows distinct non-linear behavior, which is in a better agreement with non-linear Hoek–Brown criterion than linear Mohr–Coulomb criterion. For a kind of rock that has been evaluated as a Hoek–Brown material, a new evaluation criterion is put forward by adopting optimal approximation polynomial theory, which can be used to confirm more precisely the strength parameters (cohesion and internal friction angle) of flawed samples. For intact samples, the marble leads to typical shear failure mode with a single fracture surface under different confining pressures, while for flawed samples, under uniaxial compression and a lower confining pressure (σ₃ = 10 MPa), tests for coarse and medium marble (the coarse and medium refer to the grain size) exhibit three basic failure modes, i.e., tensile mode, shear mode, and mixed mode (tensile and shear). Shear mode is associated with lower strength behavior. However, under higher confining pressures (σ₃ = 30 MPa), for coarse marble, the axial supporting capacity is not related to the geometry of flaw. The friction among crystal grains determines the strength behavior of coarse marble. For medium marble, the failure mode and deformation behavior are dependent on the crack coalescence in the sample. The present research provides increased understanding of the fundamental nature of rock failure under conventional triaxial compression.     

含水率和围压对安家岭泥岩峰后力学特性影响的试验研究

为分析含水率和围压对泥岩峰后力学特性的影响,从山西安家岭矿取泥岩,制成不同含水率的5组试样,在YAW2000电液伺服试验机上开展了三轴试验,获得了不同含水率泥岩试样三轴全程应力应变曲线,使用激光共聚焦显微镜观测了泥岩增水过程中微观结构变化。利用试验结果,分析了围压和含水率对泥岩峰值强度、残余强度、弹性模量、破坏应变和脆性模量的影响规律和泥岩增水过程中微观结构的变化规律。引入脆性模量系数和强度退化指数来描述围压对泥岩峰后强度退化过程和残余强度的影响,与FLAC中的SS模型结合,建立了考虑围压影响的泥岩应变软化力学模型,模拟了围压对泥岩应变软化行为的影响。研究结果表明:(1)随着围压增加,泥岩的峰值强度、偏应力峰值、破坏应变和残余强度都增长,峰后强度降低速率趋缓,强度退化指数和脆性模量系数可以较好地描述围压对泥岩残余强度和峰后强度退化过程的影响。(2)泥岩增水过程中,岩样内微裂隙及尺寸增长,泥岩的力学性质劣化。随着含水率增加,泥岩的弹性模量、峰值强度和残余强度降低,破坏应变增长。含水率与泥岩的弹性模量、峰值强度和破坏应变之间近似服从线性关系。(3)本文基于脆性模量系数的岩石应变软化模型能较好地描述三轴压缩泥岩的全程变形行为。     

动静荷载作用下岩石裂纹扩展应力阈值识别

压缩荷载作用下岩石裂纹扩展应力阈值的识别是理解岩石渐进破坏过程和分析岩石宏观破坏机制的重要基础。对大理岩、粗花岗岩和细花岗岩开展了单轴压缩和动态冲击试验,引入岩石裂纹轴向应变和裂纹径向面积应变两个参数,根据岩石单轴压缩破坏时裂纹径向面积应变曲线斜率的不同,把以上三种岩石分成类型Ⅰ（大理岩）和类型Ⅱ（粗花岗岩和细花岗岩）岩石。研究表明,对于类型Ⅰ和类型Ⅱ岩石,分别利用其裂纹轴向应变和裂纹轴向应变刚度曲线特征点能准确识别出岩石在静态压缩荷载下裂纹稳定扩展应力σ_sd、裂纹不稳定扩展应力σ_usd以及裂纹相互贯通应力σ_ct,证明了仅利用轴向应变数据就可对类型Ⅰ和类型Ⅱ岩石静荷载下应力阈值进行识别。而后将裂纹轴向应变法推广至动态冲击荷载下岩石的应力阈值识别,解决了动态冲击压缩载荷作用下试样难以进行裂纹扩展应力阈值识别的问题。与静态荷载下岩石的裂纹扩展应力阈值不同,在动态冲击荷载下,岩石裂纹稳定扩展应力与峰值强度的比值有所减小,裂纹不稳定扩展应力和裂纹相互贯通应力阈值相等,且与峰值强度的比值也有所减小,岩石产生更多的贯通裂纹,试样破坏时破碎程度更高。

     

砂岩峰后卸除围压过程的渗透性试验研究

为了探讨煤层开采引起的围岩卸除围压过程中砂岩渗透性的变化规律,本文用数控瞬态渗透法在电液伺服岩石力学试验系统MTS815.02上进行了砂岩试样的渗透特性试验。得出了试样峰前渗透系数-应变与应力-应变的关系曲线,以及在峰后保持轴向应变一定卸除围压过程中试样的渗透系数-围压与主应力差-围压的关系曲线;对试验砂岩在变形破坏过程中渗透性变化规律进行了总结,重点分析了其峰后卸除围压过程中渗透性的变化规律;并对试验砂岩峰后渗透系数与有效围压关系进行了拟合,得出了拟合方程式,为煤层开采引起的围岩体应力场与渗流场耦合问题提供参考。     

高低温加载对大理岩力学特性影响的试验研究

许多工程（如采矿、隧道掘进、地热开采等）都涉及到岩石损伤及破碎问题．传统的岩石损伤破碎技术,如爆破法、水射流法、机械掘进法等均面临着一系列问题,利用岩石的热损伤性质辅助机械破岩有望实现安全、高效破岩的目的．大理岩是一种典型的硬岩,常见许多工程之中,因此本文以大理岩为研究对象,首先将均质性较好的大理岩试样加热至不同温度(20~1000 °C)后放入液氮中进行急速冷处理,然后对其进行了系列的物理力学性质测试．试验结果表明：处理后密度、纵波波速、抗拉强度、单轴抗压强度(UCS)和弹性模量整体上都随温度的上升而下降;当加热温度在100 °C之前,大理岩表现出一定的热硬化现象,即随着温度升高,其UCS、纵波波速以及弹性变形模量均增大;UCS变化的阈值温度为400 °C左右,一旦温度超过400 °C,UCS迅速下降,其速率达到了9 MPa/100 °C,当温度超过500 °C弹性模量迅速下降,其速率达到7.00 GPa/100 °C,表明岩样抵抗变形能力减弱．整体上,热加载降低了大理岩的脆性,使其在单轴作用下的破坏模式由脆性破坏逐渐转化为弹塑性破坏．     

频繁动力扰动对围压卸载中高储能岩体的动力学影响

基于冬瓜山铜矿深部巷道围岩开挖过程中面临的高应力和频繁爆破扰动问题,利用改进的SHPB动静组合加载系统,开展了频繁动力扰动对围压卸载中高储能岩体动力学影响的研究。研究结果表明,围压卸载中的矽卡岩受到动力扰动时,其动态峰值应力和弹性模量随动力扰动次数非线性变化。围压卸载中的高储能矽卡岩受到动力扰动时会释放能量。轴压促使岩样内微裂隙轴向发育,造成岩样抵抗动力扰动能力减弱;围压减缓岩样内微裂隙轴向发育,造成岩样抵抗动力扰动能力增强。动力扰动对微裂隙扩展有促进作用,使围压卸载中的岩样由拉伸破坏向剪切破坏转变。     

砂岩破坏特性与能量耗散的试验研究1)

通过三轴卸荷试验,探究了不同路径下卸荷速率对砂岩力学特性及破坏过程中的能量耗散的影响。试验结果表明在全过程应力-应变曲线的弹性阶段,轴向变形起主导作用,弹塑性阶段,环向应变的增加值大于轴向应变增加值。在围压卸荷阶段,卸荷速率越小,卸荷阶段的应变折合柔度越大,此时岩样的变形不充分,呈现明显的脆性破坏。恒主应力差路径下的耗散能大于恒轴压路径下的耗散能的35%,卸荷速率越大,岩样的弹性应变能越小。     

动力荷载对围压卸载下岩石动态变形模量的影响

利用SHPB岩石动静组合加载实验系统,研究在不同轴压水平下围压以1 MPa/s速率卸载至预加值50%时矽卡岩受频繁冲击作用的动态变形模量变化规律。实验结果表明：高轴压促使岩石内部微裂纹萌发与扩展,降低了岩石抵抗外部冲击的能力。围压的侧向约束阻碍岩石内部裂纹的横向扩展,但在围压卸载时会加剧岩石内部的损伤,这是由于高轴压下,围压卸载导致岩石内部应力重新分布。轴压与围压卸载共同影响着冲击作用下的岩石动态变形模量,通过岩样在冲击荷载下的能量耗散分析岩石动态变形模量的变化规律,有助于了解深部岩体开挖的破坏机制。

     

泥岩损伤特性试验研究

以南京长江三桥地基中的泥岩为对象,对泥岩进行三轴试验。试验结果表明：随着侧压的增大,破坏荷载增大,塑性变形明显增大,岩石破坏后,残余强度随侧压增大而提高。在此基础上研究分析了泥岩微元强度服从Weibull分布,泥岩微元体破坏服从莫尔-库仑岩石强度判据时的损伤软化参数与围压的关系特征。结合岩石破裂过程应力 应变全过程曲线,讨论了初始损伤特性,分析结果表明：泥岩初始损伤时的主应力差对数随围压增大而增大,两者呈线性关系; 分析了泥岩损伤变量随主应力差变化关系,结果表明泥岩损伤变量与主应力差呈双曲线数学关系,通过对双曲线模型作线性化处理,结合试验数据采用回归分析法确定模型参数,分析结果发现F 0随围压的增大而增大,而m则随压的增大而减小,反映泥岩随围压的增大,脆性度降低。     

花岗岩破坏过程能量演化机制与能量屈服准则

为了明确岩石破坏的能量演化特性，结合单轴实验和颗粒流程序获得花岗岩的细观力学参数，进行不同应力状态的花岗岩实验，研究不同围压下花岗岩破坏过程的能量演化机理并推导能量屈服准则。获得以下主要结论:花岗岩破坏过程中低围压下内部损伤出现较早而高围压较晚，表明低围压花岗岩内部损伤是渐进发展过程，而高围压下内部损伤一旦出现便快速发展破坏；高围压花岗岩峰值前一定应变范围弹性应变能基本保持不变，吸收的能量全部转化为耗散能，表明高围压破坏时花岗岩内部损伤程度严重；弹性应变能经历不断积累并达到弹性储能极限而后减小的变化过程，而弹性储能极限与围压之间存在线性变化规律，因此高围压下岩体开挖卸荷时极易诱发大量弹性应变能的急剧释放，引起围岩失稳甚至发生岩爆；花岗岩峰值破坏时的能量比与围压无关，为一定值；基于能量原理导出了能量屈服准则，该准则包含岩性参数和所有主应力，能够综合反映岩石破坏影响因素。     

A micro–macro method for predicting the shear strength of brittle rock under compressive loading

Microcracks have great significance for shear strength of brittle rock in compression. A major challenge of this area is to establish the correlation of microcracks and macroscopic shear strength. A new micro–macro method is presented to predict the shear strength of brittle rock in compression. This method incorporates the microcrack model suggested by Ashby, Mohr–Coulomb failure criterion and a crack-strain relation. This crack–strain relation is presented to link the crack growth and axial strain by combining the micro and macro definitions from rock damage. The shear strength and stress–strain relationship of Jinping marble are theoretically investigated in detail. The rationality of this suggested method is verified by using the experimental results founded on Jinping marble. Effects of the initial microcrack size, friction coefficient and confining pressure on internal friction angle, cohesion, and shear strength are also discussed.     

复杂加载下混凝土的弹塑性本构模型

混凝土材料在不同应力路径下或复杂加载条件下会表现出差异性显著的应力应变关系,在小幅循环加载条件下,其应力应变关系会表现出类似于弹性变形的滞回曲线.在不同应力水平下,混凝土的应力应变关系以及破坏特性都具有静水压力相关特点,即随着静水压力增大,各向异性强度特性弱化.此外,混凝土受压及受拉破坏机理不同,因而对应于混凝土硬化损伤亦有不同,即可分为受压硬化损伤,受拉硬化损伤及两者的混合硬化损伤类型.基于Hsieh模型,对该模型进行了三点改进.（1）针对小幅循环加载下混凝土无塑性变形的试验规律,而模型中在应力水平较低的循环加载条件下始终存在塑性变形的预测问题,采用在边界面模型框架下,设置了应力空间的弹性域,初始屈服面与后续临界状态屈服面几何相似的假定.（2）基于广义非线性强度准则将原模型采用变换应力方法将其推广为三维弹塑性本构模型,采用变换后模型可合理的考虑不同应力路径对于子午面以及偏平面上静水压力效应形成的影响,并避免了边界面应力点奇异问题.（3）分别对拉压两种加载损伤模式建议了相应的硬化参数表达式,可分别用于描述上述加载中产生的应变软化及强度退化行为.基于多种加载路径模拟表明:所建立的三维弹塑性本构模型可合理地用于描述混凝土的一般应力应变关系特性.      

考虑围压效应的冻结砂土动态本构模型研究

为描述主动围压作用下冻结砂土的动态力学特性,通过在朱-王-唐模型的非线性体上串联塑性体,建立了能够考虑围压效应的冻结砂土动态损伤本构模型;分析了损伤参数对应力-应变曲线特征、屈服点、峰值应力和峰值应变的影响规律,基于冻结砂土动力学试验数据确定了模型参数;通过将模型和试验数据进行对比,并对不同试验条件下模型的预测误差进行分析,验证了模型的适用性和准确性。结果表明,损伤参数对应力-应变曲线弹性阶段和屈服点无明显影响,而对塑性阶段和破坏阶段的影响较为显著,本构模型预测的应力-应变曲线与试验结果具有较好的一致性。模型能够预测围压引起冻结砂土塑性阶段占比大和屈服点明显的特征,且能够描述围压对冻结砂土动态强度的增强效应;不同负温和主动围压条件下,模型对峰值应力和屈服强度的预测效果优于峰值应变和屈服应变。     

Loading rate and confining pressure effect on dilatancy,acoustic emission,and failure characteristics of fissured rock with two pre-existing flaws

Investigating the dilatancy, acoustic emission and failure characteristics of fissured rock are significant to ensure their geotechnical stability. In this paper, the uniaxial and triaxial compression experiments with AE monitoring under different loading rates were carried out on fissured rock specimens with the same geometrical distribution of two pre-existing flaws. The dilatancy and AE activity of these specimens were discussed, and the effects of the confining pressure and loading rate on the mechanical parameters and failure characteristics were analyzed. The results show that the exponential strength criterion is more suitable than the Mohr–Coulomb strength criterion to characterize the strength characteristics of fissured rock. The crack evolution and failure characteristics of fissured rock specimens are more complicated than those of intact rock specimens. The failure characteristics of the fissured rock follow the tensile shear coalescence model, crack branching occurs with increasing the loading rate, and the multi-section coalescence model is verified with increasing the confining pressure. The phenomena of stress drop and yield platform usually occur after the dilatancy onset, the specimen does not fail instantaneously, and the propagation and coalescence of cracks cause a sharp increase in the AE signals, circumferential strain, and volumetric strain.     

高温花岗岩遇水快速冷却后力学性质实验研究1)

通过对高温加热-遇水快速冷却后的花岗岩试样进行单轴和三轴实验,研究了800°C内高温花岗岩遇水快速冷却后的力学性质随温度和围压的变化规律。实验结果表明：(1)400°C为高温加热-遇水快速冷却对花岗岩力学性质影响的阈值;(2)同一温度条件下,峰值偏应力、峰值应变随围压的增大而增大;弹性模量随围压的增大先增大后减小;(3)单轴实验中,温度低于400°C时,岩样表现为复合破坏,随着温度的升高破坏形式转变为拉破坏;三轴实验中,岩样整体上表现为剪切破坏。     

恒定动载下高温水冷后玄武岩的动力特性及本构模型

为研究地应力、地温和动力扰动下岩石的动力特性,利用带围压的分离式霍普金森压杆装置,对常温（25 ℃）和经历不同高温水冷（100、300、450和600 ℃）后的玄武岩试样开展了恒定动载下不同围压等级（2、4和6 MPa）的动态压缩实验,借助静态力学实验及微观实验的测试结果,分别探讨了温度和围压对玄武岩动态力学特性及破坏特征的影响规律,并基于Weibull分布理论,构建了恒定动载下高温水冷后玄武岩的动态本构模型。结果表明：3组围压下,玄武岩的动态峰值应力、弹性模量均存在温度劣化效应,且围压越高,温度劣化效应越显著;常温和经历100~600 ℃高温水冷后玄武岩的动态峰值应力、弹性模量均存在围压强化效应,但该围压强化效应在600 ℃时有所减弱。围压一定时,随着温度的升高,试样的破碎程度不断加剧;温度一定时,随着围压的升高,试样的破碎程度逐渐降低。所建立的玄武岩动态本构模型与实验结果具有较好的一致性,可用于预测玄武岩在高温水冷和主动围压耦合作用下的动态力学行为,从而为地下资源开发及地下工程防护提供理论支持。

     

饱水对煤层顶板砂岩单轴压缩破坏能量影响的分析

为研究饱水对砂岩力学参数和能量特征的影响,利用RMT-150B岩石力学系统对煤层顶板砂岩自然和饱水试样进行单轴压缩试验。试验结果表明:饱水对砂岩试样的强度和变形参数均有不同程度的影响,软化系数为0.79,弹性模量降幅为5.25%,变形模量降幅为5.92%;饱水后砂岩试样峰值前吸收能量、可释放弹性能和耗散能均有不同程度降低,吸收能量降幅36.8%,可释放弹性能降幅为34.4%,耗散能降幅为57.7%;饱水后砂岩储蓄能量的能力有较大减弱,脆性减弱,塑性明显增强;饱水砂岩试样压缩过程中积蓄可释放能难以使试样滑移破坏,仍需要吸收部分能量使试样逐步失稳破坏;饱水对砂岩试样压缩过程吸收能量、可释放能量比例关系的影响较小,而对耗散能比例关系的影响较大;自然状态下砂岩试样峰值前相同应变条件下吸收能量、可释放能均明显高于饱水试样对应能量值;深部巷道位置确定和支护设计时应充分考虑水对巷道围岩弱化的影响,对于完整坚硬围岩采用高压注水软化可有效防止冲击地压发生和减缓灾害程度。     

基于Lemaitre原理改进砂岩蠕变损伤模型研究

以煤矿巷道围岩（砂岩）为研究对象,采用MTS815.02岩石力学试验系统,对流固耦合蠕变过程中孔隙水压力作用机制展开研究,以伯格斯模型为基础,基于Lemaitre原理建立改进的伯格斯非线性蠕变损伤模型,可以得到如下主要结论：当围压越大,岩石蠕变最后一级荷载作用持续时间越长,相对经历衰减蠕变和稳定蠕变时间越长;且由最终一级破坏蠕变变形值可知,孔隙水压较小时,蠕变变形量相对较大,此时围压增大提升了岩石延性特性,但是孔隙水压增大却削弱了围压作用,由于孔隙水压使得岩石力学性能劣化,因而减少了岩石在破坏时蠕变变形量;随后基于Lemaitre原理建立的伯格斯非线性损伤蠕变模型,可以较好地描述岩石的衰减蠕变、稳定蠕变与加速蠕变阶段;且试验曲线与拟合曲线吻合度高,验证了本文所建立损伤流变模型的合理性．     

考虑裂隙间相互作用情况下围压卸荷过程应力应变关系

岩体的稳定性和变形特性主要决定于裂隙，同时裂隙间的相互作用对岩体的稳定和变形产生显著的影响。裂隙岩体在加载和卸荷条件下的力学特性有显著的区别。为此本文首次利用位错模型法结合叠加原理研究在围压卸荷条件下裂隙间的相互作用对岩体的变形的影响问题。文中推导了考虑裂隙间的相互作用情况下裂隙岩体围压卸荷过程的应力应变关系及应力强度因子表达式，且进行了数值计算。