高强铝合金的动态拉伸断裂行为实验研究

采用不同的冲击加载方式对棒材铝合金(2024-T4、7075-T6)进行动态拉伸断裂实验研究.单轴动态拉伸加载下7075 T6的初始屈服应力与断裂应变明显高于2024 T4,但三点弯曲和层裂实验中,2024 T4表现出更好的抗裂纹扩展与层裂失效能力.断口扫描电镜分析发现:2024-T4中孔洞或裂纹主要成核于晶内强化相,形成穿晶断裂,而7075-T6部分孔洞或裂纹在晶界成核增长形成沿晶断裂,部分孔洞或裂纹在晶内强化相周成核形成穿晶断裂.     

拉伸应力区的声速测量、层裂强度和断裂密度

1 引言 在层裂的实验研究中,目前尚无法直接测量发生在材料内部的动态断裂过程。通常采用测量自由面速度剖面,推演出材料层裂特性的方法。在计算材料发生断裂时的拉伸应力即层裂强度时,需要知道拉伸应力即负压下的声速。测量负压下的声速比测量冲击压缩下的声速要困难得多。仅仅从自由面速度剖面并不能计算出负压声速,因为通常无法确定材料中应力由压应力转变为拉伸应力的“位置”、发生层裂的位置以及时间。能否通过特别的实验设计,确定发生这些过程的时一空位置,进而获得负压声速,一直是实验研究者企求解决的问题。下面介绍两种测量负压声速的实验装置设计和计算负压声速、层裂强度和断裂密度的方法,是这方面研究工作的尝试。     

应力波在多层膜状材料中衰减特性的实验研究

脉冲载荷作用下,多层膜状材料衰减应力波的特性及其规律研究在工程结构设计中具有重要意义。本文采用分离式Hopkinson压杆(以下简称SHPB)装置,从实验角度对多层石英布和多层"石英布+聚酯铝膜"两种不同结构类型膜状材料衰减应力波特性进行研究。分析了透射应力波及应力冲量随多层膜状厚度变化的关系。通过对实验数据的拟合,给出了多层膜状衰减应力波能力和材料厚度以及材料结构的数学表征。研究结果表明,两种不同结构的多层膜状材料应力波衰减随厚度的变化关系都遵循指数衰减规律,而具有"多层石英布+聚酯铝膜"叠层结构的材料对应力波的衰减能力略强于单一多层石英布材料。本研究可作为工程应用多层膜状材料衰减应力波的实验依据。     

轴向冲击载荷作用下锥壳中弹性应力波传播的计算和实验研究

本文利用有限元分析和模型实验研究了在轴向冲击载荷作用下,锥壳中弹性应力波的传播、计算和实验结果表明,结构中存在着弹性纵波和弹性弯曲波的传播,它们传播的速度各不相同,使壳面承受不同的应力状态;讨论了纵波和弯曲波随壳面的衰减;实验指出,由于边界的影响,即使纵波的反射也会产生新的反射弯曲波沿锥面传播。     

辛方法和弹性圆柱壳在内外压和轴向冲击下的动态屈曲

针对有内压或外压的弹性圆柱壳在轴向冲击载荷耦合作用下的动态屈曲问题,构造哈密顿体系,在辛空间中将临界载荷和动态屈曲模态归结为辛本征值和本征解问题,从而形成一种辛方法。该方法直接得到非轴对称的屈曲模态。数值结果给出了圆柱壳问题的临界载荷和屈曲模态以及一些规律。     

Enhanced fracture energy and effects of temperature at spalling in ceramics: continuum damage modelling

Summary Enhanced fracture energy losses at spalling and the temperature dependence of the spalling strength of alumina ceramic bars are analysed on the basis of the experimental tests conducted both in room temperature and within the temperature range up to 1500°C at strain rates of some 500 s⁻¹. The experimental method and the measurements are first shortly outlined. The mechanical response of ceramic bars is modelled then as a heterogeneous distribution of brittle-elastic mesoelements undergoing continuum damage at the known strain history, corresponding to that registered in the experiments. The mesoelements are characterised by the values of initial damage randomly fluctuating within a given band-width superposed on a deterministic distribution, which corresponds to the fabrication conditions of the ceramic bars. The model has been tested in the evaluation of room-temperature experiments, its parameters: the average value of the initial damage, Young's modulus of the undamaged material and the energy absorption capacity in continuum damage are taken from the calibration fitting the experimental data. The registered energy losses at spalling, which exceed the static values of fracture energy by almost an order of magnitude, can be explained thus by the enhancement of the dissipation due to bulk damage, which is computed on the basis of the above parameters. The temperature change of the Young's modulus of the matrix material is taken as corresponding to the measured change of the uniaxial wave velocity in the bar, and corrected by the temperature change of the mass density. The analysis of the model shows that the drop in the spalling strength of the specimens with the increase of the temperature is phenomenologically related to the falling energy absorption capacity within the continuum damage mechanism. An explanation of this phenomenon is attempted, based on the grain-size-related mechanisms of the microfracture from pre-existing intergranular flaws distributed over the bulk of ceramics. Received 7 May 1999; accepted for publication 14 June 1999     

水中冲击波与弹性薄板耦合作用的研究

对水中冲击波与弹性薄板的流固耦合作用进行了研究,建立了实验装置。利用全息干涉法定量测量了水中动态流场,并测出受水中冲击波作用的弹性薄板在不同时刻的变形,得出相应的全息干涉条纹图。同时利用有限元法对水中冲击波与弹性薄板的流固耦合问题进行了数值计算。研究结果表明,用实验方法能够较好地模拟水中冲击波与弹性结构的耦合作用,用有限元法计算水中冲击波传播问题是可行的。     

A study of the in situ transverse tensile lamina strength and the classical solution of the opening mode crack in a 0/90/0 laminate

In this paper, the classical solution of the opening mode crack in the 90° layer of 0/90/0 laminates has been determined by means of Fourier transformations and the procedure of Copson for a pair of dual integral equations. The fracture behavior and the in situ transverse strength of the 90° layer have been quantitatively studied in graphite/epoxy laminates, based on the solution obtained above. The results show that the stress intensity factor of this kind of laminates, which is different from that of a single unidirectional 90° layer, decreases with the increase in thicknessb, or modulusE _L orG _LT of the 0° layer and also decreases with the decrease in the thickness of the 90° layer. So the lamination effect manifests itself and thein situ transverse strength of the 90° layer is thereby enchanced. The theoretical calculations agree with the experimental data presented by D.L. Flaggs. Supported by National Natural Science Fundation of China.     

饱和水泥试样被爆炸激波损伤破碎的尺度研究

利用水中爆炸冲击波使水泥试样损伤破坏,模拟爆炸采油时激波使岩石损伤开裂的现象。实验获得了适合本实验条件的激波峰压衰减规律pm8.2(W1/3/R)1.46,得知压碎区尺度为集中装药特征尺度的2～5倍、拉伸损伤区尺度为集中装药特征尺度的20～30倍,激波使水泥试样破碎、拉裂的能量占总能量的2%～7%。     

黄土和砂土岩中填实爆炸辐射弹性波的对比研究

研究地下爆炸弹性区的震动特性,关键是获得场地介质与爆炸能量耦合作用下辐射弹性波的实验参数。对于不易加工成大尺寸模型的砂土岩,为研究其填实爆炸下辐射弹性波的特征,采用0.125 g TNT微型炸药球作为爆炸源,以塑性区可置换的?1 370 mm×1 200 mm黄土样品作为提供应力波传播路径的载体,用波阻抗近似相等的重塑黄土和砂土岩样品分别作为源区介质,对比分析了两种介质中微药量填实爆炸辐射的弹性波传播特征。实验结果表明:在测试范围内,两种介质中填实爆炸激发的弹性应力波粒子速度(位移)峰值的衰减规律、波形的主频变化规律一致;砂土岩中爆炸辐射的弹性波粒子速度(位移)峰值整体高于黄土、粒子速度波形的半高宽和主频低于黄土;砂土岩中爆炸耦合的向外传播的弹性波能量比黄土大。实测结果反映,黄土和砂土岩中填实爆炸弹性波能量耦合强度的差别。     

Propagation of wave at the boundary surface of transversely isotropic thermoelastic material with voids and isotropic elastic half-space

The purpose of this research is to study the effect of voids on the surface wave propagation in a layer of a transversely isotropic thermoelastic material with voids lying over an isotropic elastic half-space. The frequency equation is derived after developing a mathematical model for welded and smooth contact boundary conditions. The dispersion curves giving the phase velocity and attenuation coefficient via wave number are plotted graphically to depict the effects of voids and anisotropy for welded contact boundary conditions. The specific loss and amplitudes of the volume fraction field, the normal stress, and the temperature change for welded contact are obtained and shown graphically for a particular model to depict the voids and anisotropy effects. Some special cases are also deduced from the present investigation.     

垂直断层破碎带对Rayleigh波传播与场地地震动反应的影响

采用基于时域粘弹性人工边界的Rayleigh波输入方法,对具有不同宽度、不同剪切波速的垂直断层破碎带的场地进行了Rayleigh波作用下的动力时程反应分析,研究了垂直断层的宽度与剪切波速变化对Rayleigh波传播及场地地震动反应的影响。计算结果表明:在Rayleigh波入射一侧的中远场地表面,断层宽度与剪切波速的变化对地面峰值位移反应影响很小;在Rayleigh波入射一侧的断层角点以及距角点较近处,随着断层宽度的增大或剪切波速的减小,峰值位移反应均增大;在另一侧中远场地面的峰值位移反应随着断层宽度的增大或剪切波速的减小而减小,且水平位移峰值减小的程度略大于竖向位移峰值。由此可以看到,软弱的断层破碎带对通过的Rayleigh波有削弱作用,且破碎带越宽或剪切波速越小削弱作用越明显。     

基于第二类四边形面积坐标的弹性力学纯弯解及MacNeal局限定理的破解

为了提高有限元的性能,弹性力学的解析解(齐次方程的通解)常常可用作有限元的试探函数。然而单元自由度数与完备的直角坐标解析解个数并不匹配,不完备的试函数会导致单元有方向依赖性。利用新型局部自然坐标——第二类四边形面积坐标QACM-II(S,T),给出了平面问题对应任意方向纯弯曲状态的应力函数解析解,即S3和T3的线性组合,并推导出了这两组应力函数对应的应力、应变和位移解析解。之后,利用QACM-II表示的解析解构造了非对称的平面4节点8自由度单元USQ4,该单元可以同时通过常应力/应变分片检验和纯弯测试,从而破解了MacNeal局限定理对平面低阶单元的限制。     

THE NEW CRITERIA OF ELASTIC AND FATIGUE FAILURE IN THE COMPONENT OF COMPLEX STRESS STATES

In this paper, a total criterion on elastic and fatigue failure in complex stress, that is, octahedral stress strength theory on dynamic and static states on the basis of studying modern and classic strength theories. At the same time, an analysis of an independent and fairly comprehensive theoretical system is set up. It gives generalized failure factor by 36 materials and computative theory of the 11 states of complex stresses on a point, and derives the operator equation on generalized allowable strength and a computative method for a total equation can be applied to dynamic and static states. It is illustrated that the method has a good exactness through computation of eight examples of engineering. Therefore, the author suggests applying it to engineering widely.