催化剂对纳米聚团床法制备的纳米碳材料形貌的影响

 在纳米聚团床中用催化化学气相沉积法批量制备了碳纳米管，研\r\n究了过渡金属催化剂对碳纳米管形貌和产量的影响．实验结果表明，含\r\n铁催化剂的活性较低，产率较低，但产品质量较好；含镍催化剂的活性\r\n较高，产率较高，但产品质量较差；在钴催化剂作用下发现了一种新型\r\n的针状纳米碳材料．用含载体较少的铁催化剂可以得到纯度较高且微观\r\n结构较好的碳纳米管，但产率较低；不含任何载体的纯镍催化剂则不能\r\n得到碳纳米管．适宜的催化剂组成、催化剂活性点的均匀分布和裂解速\r\n度的控制等构成了纳米聚团床大批量制备碳纳米管技术的关键．     

硝基苯加氢合成对氨基酚用负载铂催化剂的制备

 用甲醛还原沉积法制备了活性炭负载的铂催化剂（Pt／AC）和不\r\n同载体负载的铂催化剂，并考察了催化剂对硝基苯加氢制备对氨基酚反\r\n应的催化性能．结果表明，还原Pt（Ⅳ）的甲醛用量是影响催化剂性能\r\n的关键因素，甲醛必须过量而且存在一个最佳值．增加催化剂的铂负载\r\n量，不能有效提高加氢反应速度，反而易降低对氨基酚选择性；低铂负\r\n载量催化剂具有较高的活性、选择性及稳定性．XPS和TEM表征结果表明\r\n，金属铂集中分布于活性炭颗粒外部，其颗粒大小介于2～12nm间．炭\r\n载体催化剂的活性和选择性明显高于金属氧化物载体催化剂．掺入适量\r\n的Mg可显著提高Pt／AC催化剂的活性和选择性．     

纳米二氧化锆催化剂上一氧化碳加氢合成异丁烯

 考察了纳米ZrO2的制备方法及Al2O3和KOH助剂的添加对ZrO2催化\r\nCO加氢合成异丁烯反应的影响．纳米ZrO2的制备方法对ZrO2的物理性质\r\n和催化性能有较大的影响．用超临界流体干燥法干燥并在流动N2气氛中\r\n焙烧制得的ZrO2催化剂对异丁烯具有较高的选择性．Al2O3和KOH助剂表\r\n现出非常优良的助剂效应，在大幅度提高催化剂对i－C4烃选择性的同\r\n时保持了和ZrO2同样高的催化活性．催化剂的酸碱性表征结果表明，酸\r\n碱性对催化剂的催化性能影响很大，催化剂上适宜的酸碱数量和酸碱比\r\n例是影响其催化CO加氢合成异丁烯性能的非常重要的因素．     

钼催化剂上甲醇直接气相羰基化活性与吸附的关系

 制备了一系列非负载的钼催化剂，考察了催化剂上甲醇直接气相\r\n羰化活性与反应物及产物吸附的关系．结果发现，催化剂的制备方法对\r\n甲醇直接气相羰化活性的影响很明显，以纯二硫化钼试剂制备的催化剂\r\n，甲醇转化率与羰化产物乙酸甲酯的选择性最低；以三氧化钼气相还原\r\n硫化制备的催化剂，其羰化活性较低；以钼酸铵溶液经硫化铵溶液或硫\r\n化氢气体硫化制得的催化剂，其性能明显优于前两种，尤以钼酸铵经硫\r\n化铵溶液硫化制得的催化剂的性能最佳．催化剂的羰化活性明显依赖于\r\n催化剂的吸附性能，羰化活性高的催化剂不仅吸附CO的量大，而且对甲\r\n醇和乙酸甲酯的吸附量也明显较大．     

氧化铝负载钌基氨合成催化剂的制备条件及载体改性

 利用等体积浸渍法制备了氧化铝负载钌基氨合成催化剂．考察了\r\n氢氧化铝的焙烧温度，催化剂的还原温度，助剂K、Ba和Sm的添加，以\r\n及用MgO和BaO改性氧化铝载体等对催化剂活性的影响．通过XRD，N2物\r\n理吸附和CO2化学吸附等方法表征了载体的物相结构、比表面积和表面\r\n碱性．研究结果表明，氧化铝表面碱性随着氢氧化铝焙烧温度的升高而\r\n增大是催化剂活性升高的主要原因，载体比表面积的降低对催化剂活性\r\n的影响相对较小．助剂K、Ba和Sm的加入显著地提高了催化剂的活性，\r\n同时助剂Ba和Sm还减弱了强吸附氢对氮吸附的抑制作用，明显提高了催\r\n化剂的高压活性．用MgO改性氧化铝载体降低了其比表面积，但是显著\r\n地提高了载体的表面碱性和催化剂的活性．BaO改性的氧化铝载体的比\r\n表面积、表面碱性及其负载的钌基催化剂的活性随着BaO含量的增加先\r\n升高后降低，当BaO摩尔含量为7．7％时，催化剂活性最高．     

制备条件对Al1P1.30Ti0.30Si0.17体系催化剂性能的影响

 从制备催化剂的原料、沉淀剂种类、铝沉淀物终点的pH值、水量\r\n及原料的加入顺序等方面考察了制备条件对AlP1．30－Ti0．30Si0．1\r\n7体系的结构及催化性能的影响．结果表明，以自制新鲜氢氧化铝为铝\r\n源，以硅溶胶为硅源，以钛酸丁酯为钛源，以氨水为沉淀剂，在pH＝6\r\n．2，c（Al3＋）＝0．64mol／L（V（H2O）＝200ml）的条件下，采用\r\n通常的沉淀方法可制备出性能优良的催化剂．催化剂的酸性是影响其催\r\n化性能的主要因素，主产物选择性与酸强度有关，酸强度高的催化剂具\r\n有较低的主产物选择性；催化剂的活性与其孔径及表面酸量有关；催化\r\n剂中的B酸中心是反应可能的活性中心．     

Ni含量及预硫化对NiW/γ-Al2O3催化剂上噻吩加氢脱硫反应活性的影响

 采用连续流动微反装置考察了活性组分Ni／（Ni＋W）原子比及\r\n预硫化条件对NiW／γ－Al2O3催化剂噻吩加氢脱硫（HDS）反应活性的\r\n影响．用X射线光电子能谱和电镜微区元素分析方法对硫化态催化剂进\r\n行了表征．结果表明，催化剂的组成、硫化方法、硫化度和反应条件等\r\n都能影响NiW／γ－Al2O3催化剂的HDS反应活性．对于在较低温度（30\r\n0℃）下硫化的催化剂，当反应温度较低（260～290℃）时，最佳Ni／\r\n（Ni＋W）原子比为0．50，而当反应温度较高（330～360℃）时，最佳\r\nNi／（Ni＋W）原子比为0．23．当催化剂在300～450℃下硫化时，其噻\r\n吩HDS反应活性随硫化温度升高而增大，表明硫化度较高的催化剂具有\r\n较高的HDS反应活性．     

非均相催化一步合成碳酸二苯酯的研究 Ⅰ.载体制备方法对催化剂性能的影响

 采用溶胶－凝胶法、共沉淀法和冷冻干燥法，制备了LaxMnyPbz\r\nO复合型金属氧化物载体，并以PdCl2或Na2PdCl4的水溶液为浸渍液，通\r\n过浸渍方法制得固相催化剂，用于一步合成碳酸二苯酯．用XRD，TEM及\r\nSEM对载体及催化剂进行了表征．结果表明，三种载体的主要物相皆为\r\nLa0．3Mn0．5PbO，溶胶－凝胶法制得的载体及催化剂的粒径分布较好\r\n，空隙率较大，活性组分分散度较高；溶胶－凝胶法制得的催化剂的催\r\n化性能较好，碳酸二苯酯选择性可高于99．5％．     

正丁烷氧化制顺酐流化床催化剂的性能

 考察了前驱体制备过程中水合肼／五氧化二钒摩尔比（以下简记\r\n为n（N2H4）／n（V2O5））对催化剂性能的影响．由较高的n（N2H4）\r\n／n（V2O5）比制得的催化剂，其（VO）2P2O7相含量较多，正丁烷转化\r\n率较高．随着n（N2H4）／n（V2O5）比的减小，δ－VOPO4相的含量逐\r\n渐增多，正丁烷转化率随之升高；而顺酐选择性开始时升高，达到最大\r\n值后逐渐降低．在n（N2H4）／n（V2O5）＝0．34时制备的催化剂最佳\r\n，在丁烷浓度为4．0％、空速为500h－1及反应温度为420℃的反应条件\r\n下，顺酐收率可达49．74％．本文中细粒床催化剂有较大的操作弹性．     

过渡金属对Pd/γ-Al2O3催化剂活性的影响

 利用分步等体积浸渍的方法，从蒽醌法生产双氧水的角度，制备\r\n了系列氢化催化剂．同时，利用TPR，XRD和TEM等技术，考察了第4周期\r\n过渡金属对Pd／γ－Al2O3催化剂活性的影响．结果表明，铁系元素和\r\n锌助剂有利于钯在载体上的分散，提高了Pd的催化活性，使氢化效率提\r\n高5％～16％，抗失活能力增强．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.