可燃气体中激波聚焦的点火特性

数值模拟了二维平面激波从抛物面上反射在可燃气体中聚焦的过程,研究了形 成爆轰波的点火特性. 对理想化学当量比氢气/空气混合气体,在初始压强20kPa的条件下, 马赫数2.6-2.8的激波聚焦能产生两个点火区：第1个点火区是反射激波会聚引起的,第 2个点火区是由入射激波在抛物面上发生马赫反射引起的. 这种条件下流场中会出现爆燃转 爆轰,起爆点分别分布在管道壁面、抛物反射面和第2点火区附近. 起爆机理分别为激波管 道壁面反射、点火诱导激波的抛物面反射和点火诱导的激波与第2点火区产生的爆燃波的相 互作用. 不同的点火和起爆过程导致了不同的流场波系结构,同时影响了爆轰波传播的波动 力学过程.     

用环形激波聚焦实现爆轰波直接起爆的数值模拟

利用基元反应模型和有限体积法对环形激波在可燃气体中聚焦实现爆轰波直接起爆进行了数值模拟。研究结果表明，标准状态下的氢气-空气混合气体在马赫数为3.1以上的环形激波聚焦产生的高温高压区作用下会诱发可燃气体的直接起爆形成爆轰波，爆轰波与激波和接触间断相互作用产生了复杂的波系结构；爆轰波爆点位置在对称轴上并不是固定的点，而是随着初始激波马赫数的变化而发生移动；可燃气体初始温度和压力对起爆临界马赫数都有影响，但是初始温度的影响大得多。     

圆球诱发斜爆轰波的数值研究

斜爆轰发动机是飞行器在高马赫数飞行条件下的一种新型发动机,具有结构简单、成本低和比冲高等优点.但是斜爆轰发动机的来流马赫数范围广,来流条件复杂,为实现斜爆轰波的迅速、可靠引发,采用钝头体来诱发.利用Euler方程和氢氧基元反应模型,对超声速氢气/空气混合气体中圆球诱导的斜爆轰流场进行了数值研究.不同于楔面诱发的斜爆轰波,球体首先会在驻点附近诱发正激波/爆轰波,然后在稀疏波作用下发展为斜激波/爆轰波.模拟结果显示,经过钝头体压缩的预混气体达到自燃温度后,会出现两种流场:当马赫数较低时,由于稀疏波的影响,燃烧熄灭,钝头体下游不会出现燃烧情况;而当马赫数较高时,燃烧阵面能传到下游.分析表明,当钝头体的尺度较小时,驻点附近的能量不足以诱发爆轰波,只会形成明显的燃烧带与激波非耦合结构;当钝头体的尺度较大时,流场中不会出现燃烧带与激波的非耦合现象,且这一特征与马赫数无关.通过调整球体直径,获得了激波和燃烧带部分耦合的燃烧流场结构,这一流场结构在楔面诱发的斜爆轰波中并不存在,说明稀疏波与爆轰波面的相互作用是决定圆球诱发斜爆轰波的关键.     

Detonation and deflagration initiation at the focusing of shock waves in combustible gaseous mixture

Abstract. Detonation and deflagration initiation under focusing conditions in a lean hydrogen-air mixture was experimentally investigated. The experiments were carried out in a shock tube equipped with the laser schlieren system and pressure transducers. Two-dimensional wedges (53° and 90°), semi-cylinder and parabola, were used as the focusing elements. The peculiarities of mild and strong ignition inside the reflector cavity were visualized. A hydrogen-nitrogen mixture was taken for comparison between reactive and inert mixture. It was found that mild ignition inside the reflector cavity can lead to detonation initiation outside the cavity. Schlieren pictures of the process were obtained and the dependence of the distance of detonation initiation on Mach number of the incident shock wave was established. Received 30 August 1999 / Accepted 23 February 2000     

高速弹丸诱导斜爆轰激波结构实验研究

斜爆轰推进系统在高超声速推进领域具有广阔的应用前景,其释热迅速、比冲高、燃烧室结构简单的优点吸引研究人员的持续关注.然而,斜爆轰的地面试验同时涉及到高速试验环境模拟、燃料与氧化剂混合、高温燃烧流场结构测量等技术难点,当前国内外系统的试验研究仍然十分有限,难以支撑斜爆轰发动机的研制.为了研究自持传播的斜爆轰激波结构与波面流动特性,基于爆轰驱动二级轻气炮开展了高速弹丸诱导斜爆轰实验研究,使用直径30 mm球头圆柱形弹丸发射进入充满氢/氧可燃混合气体的实验舱中以起爆斜爆轰波,并采用两种阴影技术对实验流动结构进行测量.实验中在不同速度、不同充气压力下观察到三种弹丸诱导激波结构,即激波诱导燃烧、弹丸起爆爆轰波和相对弹丸驻定的斜爆轰波,实验舱充气压力下降则会造成爆轰横波尺度增加与波面流动失稳.实验中,斜爆轰激波角与理论分析结果吻合较好,弹丸气动不稳定带来较大的弹丸攻角会对激波角测量带来一定偏差.通过对斜爆轰波波面法向传播速度的测量发现,随着远离弹丸,斜爆轰传播速度由弹丸飞行速度衰减至接近实验气体CJ速度,弹丸速度的降低会加速斜爆轰波传播速度的衰减.     

斜爆轰的多波结构及其稳定性研究进展

斜爆轰是气相爆轰物理的一个重要研究方向,在航空航天新型动力领域有重要的潜在应用价值.作为激波诱导的高速燃烧, 斜爆轰波可以简化为包含能量添加的间断面.然而, 斜爆轰流动中往往涉及激波、湍流等多种的流体力学现象,它们和燃烧放热耦合在一起, 导致流动和燃烧机理非常复杂. 一方面,斜爆轰波具有的多尺度和非线性的特征, 理论研究难以深入; 另一方面,爆轰波流场高温、高压、高速的特点, 又给实验研究带来了很大的困难.过去20年, 主要借助数值方法,研究者对斜爆轰波开展了系统的模拟和分析,在诸多方面取得了明显的进展.本文首先介绍了理想情况下的起爆区波系结构和波面稳定性研究进展;其次着眼于推进系统的问题,关注了非均匀来流效应以及斜爆轰波与稀疏波的作用;最后对未来的研究工作提出一些建议.      

Supersonic flow of combustible gas mixture past sphere with account for ignition delay time

Assume an axisymmetric blunt body or a symmetric profile is located in a uniform supersonic combustible gas mixture stream with the parameters M₁, p₁, and T₁. A detached shock is formed ahead of the body and the mixture passing through the, shock is subjected to compression and heating. Various flow regimes behind the shock wave may be realized, depending on the freestream conditions. For low velocities, temperatures, or pressures in the free stream, the mixture heating may not be sufficient for its ignition, and the usual adiabatic flow about the body will take place. In the other limiting case the temperature behind the adiabatic shock and the degree of gas compression in the shock are so great that the mixture ignites instantaneously and burns directly behind the shock wave in an infinitesimally thin zone, i. e., a detonation wave is formed. The intermediate case corresponds to the regime in which the width of the reaction zone is comparable with the characteristic linear dimension of the problem, for example, the radius of curvature of the body at the stagnation point.The problem of supersonic flow of a combustible mixture past a body with the formation of a detonation front has been solved in [1, 2]. The initial mixture and the combustion products were considered perfect gases with various values of the adiabatic exponent .These studies investigated the effect of the magnitude of the reaction thermal effect and flow velocity on the flow pattern and the distribution of the gasdynamic functions behind the detonation wave.In particular, the calculations showed that the strong detonation wave which is formed ahead of the sphere gradually transforms into a Chapman-Jouguet wave at a finite distance from the axis of symmetry. For planar flow in the case of flow about a circular cylinder it is shown that the Chapman-Jouguet regime is established only asymptotically, i. e., at infinity.This result corresponds to the conclusions of [3, 4], in which a theoretical analysis is given of the asymptotic behavior of unsteady flows with planar, spherical, and cylindrical detonation waves.Available experimental data show that in many cases the detonation wave does not degenerate into a Chapman-Jouguet wave as it decays, bur rather at some distance from the body it splits into an adiabatic shock wave and a slow combustion front.The position of the bifurcation point cannot be determined within the framework of the zero thickness detonation front theory [1], and for the determination of the location of this point we must consider the structure of the combustion zone in the detonation wave. Such a study was made with very simple assumptions in [5].The present paper presents a numerical solution of the problem of combustible mixture flow about a sphere with a very simple model for the structure of the combustion zone, in which the entire flow behind the bow shock wave consists of two regions of adiabatic flow-an induction region and a region of equilibrium flow of products of combustion separated by the combustion front in which the mixture burns instantaneously. The solution is presented only for subsonic and transonic flow regions.     

Transition of plane overdriven detonation wave to the Chapman-Jouguet regime

The asymptotic laws of behavior for plane, cylindrical, and spherical infinitely thin detonation waves were found in [1, 2] for increasing distance from an igniting source in those cases in which the waves changed into Chapman-Jouguet waves as they decayed. It was shown that the plane overdriven detonation wave approaches the Chapman-Jouguet regime asymptotically, while the transition of the cylindrical or spherical strong detonation wave into the Chapman-Jouguet wave may occur at a finite distance from the initiation source.Similar conclusions are valid for the propagation of stationary steadystate detonation waves which arise with flow of combustible gas mixtures past bodies.However, numerous experiments [3, 4] on firing bodies in a detonating gas show that the overdriven detonation wave which forms ahead of the body decays and decomposes into an ordinary compression shock and a slow combustion front. To establish why the wave does not make the transition to the Chapman-Jouguet regime, in the following we consider the propagation of a plane detonation wave and account for finite chemical reaction rates. We use the very simple two-front model (ordinary shock wave and following flame front). Conditions are found for which transition to the Chapman-Jouguet regime does not occur. We first consider the propagation of an unsteady plane wave and then the steady plane wave. It is found that for all the mixtures used in these experiments transition to the Chapman-Jouguet regime is not possible within the framework of the assumed model.     

Numerical simulation of shock wave focusing over parabolic reflectors

The problem of a plane shock wave that propagates in an air media and then is reflected from a parabolic concave reflector and focuses at some region is considered. The shock focusing can greatly magnify the pressure and the temperature. The purpose of this study is to numerically simulate the shock focusing process of the reflection of shock waves from the parabolic reflectors with different depths and to analyze their associated flow fields in detail. The present solver developed is to solve the Euler equations using an improved, implicit, upwind Total Variation Diminishing scheme in a finite-volume approach. The effects of reflectors with different depths and of the incident shock Mach numbers on shock focusing are investigated. The real-gas effect is taken into account through a proper correction of the specific heat ratio of air, when high temperature occurs due to shock focusing.     

A high-speed photographic study of the transition from deflagration to detonation wave

Experiments were conducted to investigate the DDT process of the oxyhydrogen gas in the rectangular detonation tube of 3 m long. The repeated obstacle was installed near the ignition plug and the effects of the obstacle on the DDT process were investigated. The behaviour of the combustion and detonation wave were visualized utilizing Imacon high-speed camera with the aid of Schlieren optics. As a result, DDT process was visualized, i.e. (i) multiple shock waves were induced by the expanding combustion wave, because the combustion flame played a role as a piston and compressed the unburned gases. (ii) The acceleration of the combustion wave was occurred and the distance between the shock wave and the combustion flame became shorter. (iii) Eventually, the local explosion was occurred and cause overdriven detonation wave to propagate at the velocity of about 3 kms⁻¹. An abridged version of this paper was presented at the 15th Int. Colloquium on the Dynamics of Explosions and Reactive Systems at Boulder, Colorado, from July 30 to August 4, 1995     

Distinctive features of galloping detonation in a supersonic combustible-mixture flow under an inert gas layer

The problem of detonation initiation in a supersonic flow of a stoichiometric propane-air mixture occupying partially or completely the cross-section of a plane channel is considered. The initiation in the flow is produced by a step or a wall completely cutting off the flow. The study is conducted within the framework of one-stage combustion kinetics. A numerical method based on the Godunov scheme is employed. The critical conditions for detonation formation are determined in terms of the oncoming flow velocity. A previously unknown mechanism of detonation propagation is found; it is related with the presence of the combustible mixture in the wall layer under an inert gas layer. It is due to the formation of a complicated wave structure of the flow characterized by the penetration of a shock wave formed in the inert gas layer into a combustible mixture layer ahead of the detonation wave with the result that the latter layer is heated and ignited. The process as a whole is periodic in nature, as distinct from the conventional cellular detonation in a homogeneous fluid. Many problems arise in connection with the use of detonation in engines and other power plants. The most important among them are detonation excitation and stabilization in combustion chambers. The detonation initiation within a layer under conditions of unbounded space and a fluid at rest was experimentally investigated in [1]. In the case of a combustion chamber bounded in the transverse direction, some new effects accompanying the detonation might be expected.     

激波聚焦诱导点火和爆轰的数值研究

以二维轴对称多组分Euler方程为基础，采用非正交结构化网格和改进的波传播算法，模拟了激波在抛物形反射壁面聚焦反射诱导点火和爆轰的过程，描述了其流场形态。讨论了预混气组成、入射激波强度及反射壁面形状对点火和爆轰的影响。结果表明，激波在抛物形反射壁面顶点处聚焦反射可形成局部高温高压区域，该区域在一定条件下可点燃预混气甚至形成爆轰，其中低稀释剂浓度的预混气、较大的入射激波Mach数和较深的反射壁面有利于可燃预混气形成爆轰。     

Detonation initiation developing from the Richtmyer–Meshkov instability

Detonation initiation resulting from the Richtmyer–Meshkov instability is investigated numerically in the configuration of the shock/spark-induced-deflagration interaction in a combustive gas mixture. Two-dimensional multi-species Navier–Stokes equations implemented with the detailed chemical reaction model are solved with the dispersion-controlled dissipative scheme. Numerical results show that the spark can create a blast wave and ignite deflagrations. Then, the deflagration waves are enhanced due to the Richtmyer–Meshkov instability, which provides detonation initiations with local environment conditions. By examining the deflagration fronts, two kinds of the initiation mechanisms are identified. One is referred to as the deflagration front acceleration with the help of the weak shock wave, occurring on the convex surfaces, and the other is the hot spot explosion deriving from the deflagration front focusing, occurring on the concave surfaces. The project supported by the National Natural Science Foundation of China (90205027 and 10632090).     

Numerical studies of shock focusing induced by reflection of detonation waves within a hemispherical implosion chamber

The initiation and the propagation of detonation waves in a hemispherical chamber and the imploding shock waves that are the reflected detonation waves at the chamber wall are numerically investigated. The effects of the boundary layer and the non-uniformity of the flow field induced by the detonation wave on the imploding shock stability are examined. It is found that the effect of the boundary layer separation on the chamber wall has the strongest effect on the implosion focus.     

Uncertainty analysis of deflagration-to-detonation run-up distance

Three methods were adopted to estimate the deflagration-to-detonation run-up distance in a smooth tube, which comprise (1) the measurement of the propagation speed of pressure or combustion waves compared with the C–J detonation speed, (2) the time of the onset of detonation by the emission of visible light and the trajectory of pressure wave or combustion waves, and (3) the trajectory intersection with the presence of retonation wave. A nonstationary cross-correlation technique was applied to evaluate the uncertainty in estimating the run-up distance. Evaluation of the pressure wave (pressure wave speed or the pressure wave trajectory) appears to be more suitable to determine the deflagration-to-detonation run-up distance. PACS 47.40.-x Communicated by Z. Jiang     

氢氧燃烧及爆轰驱动激波管

分析并观察了沿驱动段轴向分布多火塞燃烧驱动段的性能．提出主膜处同一管截面均匀分布三火花塞引燃的点火方法．用这种点火方法驱动产生的入射激波强度重复性较高,激波后气流速度、温度和压力的定常性亦大大改善,可满足气动试验实际要求．提出在驱动段尾端串接卸爆段来消除爆轰波反射高压,从而可使反向爆轰驱动段用来产生高焓高密度试验气流．这种反向爆轰驱动产生的入射激波重复性高,激波衰减弱．在主膜处的收缩段产生的反射波可缓解爆轰波后跟随的稀疏波的不利影响,从而使前向爆轰驱动具有实用性．在产生的入射激波强度相同条件下,前向爆轰驱动所需的爆轰驱动段可爆混合气初始压力可较反向爆轰低近一个量级．     

可燃气体中激波与障碍物作用在下游形成爆轰波的数值研究

对平面激波和单个矩形障碍物作用的过程进行了数值模拟,研究了反射产生的上行爆轰波在下游可燃气体中形成爆轰波的过程。数值结果表明,下游爆轰波形成过程主要有2种模式:爆轰波直接绕射和绕射波在上壁面反射,这和已有的实验结果是一致的。通过研究下游爆轰波的形成过程受入射激波马赫数、混合气体的压力和管道尺度的影响,分析了上游爆轰波向下游传播的波动力学过程,讨论了2种形成过程的作用规律和控制因素,阐明了下游爆轰波的形成规律。     

Initiation of gaseous detonation by a high speed body

The investigation of detonation initiated by the passage of a high speed body is presented. The following experiments are carried out for mixture of C₂H₂ + 2.5 O₂ passed by a hemispherical or blunt cylinder with velocity ranging from 800 to 1400 m/s. A new mechanism of the transformation of shock waves to detonation waves is observed at near-critical regimes. The analytical correlation between the aerodynamical characteristics of high speed body and the physico-chemical parameters of explosive mixture is proposed as the initiation criterion of gaseous detonation. Analytical and experimental data agree well with each other.This article was processed using Springer-Verlag T_EX Shock Waves macro package 1.0 and the AMS fonts, developed by the American Mathematical Society.     

气相爆轰波绕射流场显示研究

采用基于红宝石激光器（波长694.3 nm）的纹影系统,对气相爆轰波绕射进行了初步的流场显示研究。采用单色激光和合适半带宽（15 nm）的滤光片,有效地消除了爆轰波自发光对流场显示的影响。合理设置激光器同步控制系统的触发延时,得到了序列的爆轰波阵面纹影照片。结果表明:图像清晰地显示了爆轰波阵面的诱导激波、横波及化学反应区。当爆轰波在左尖点处绕射,受稀疏波作用,诱导激波与化学反应区明显分离,导致爆轰波衰减为爆燃。分离的诱导激波和折皱的化学反应区在纹影图上清晰可见。诱导激波在垂直支管右壁面反射,诱导二次起爆。畸变爆轰波在水平和垂直支管中均发生马赫反射。提高初压,爆轰波受分叉口几何属性的影响减小,畸变爆轰波在水平和垂直支管下游较易恢复为自持爆轰波。