The state energy and the displacements of the potential minima of the 2Ag− state in all-trans-β-carotene as determined by fluorescence spectroscopy

The fluorescence spectrum of all-trans-β-carotene was recorded at 170 K. The 1B_u⁺ → 1A_g⁻ fluorescence exhibited clear vibrational structures constituting a mirror image with those of the 1B_u⁺ ← 1A_g⁻ absorption, and the deconvolution of the entire spectrum identified the 2A_g⁻(0) → 1A_g⁻(0) transition at 14 500 cm⁻¹. The displacements of the 1B_u⁺ and 2A_g⁻ potential minima along ν₁ and ν₂ (the CC stretching and C–C stretching normal coordinates, respectively) were determined to be 1.2 and 0.9, and 1.6 and 1.5, respectively. Thus, much larger potential displacements in the 2A_g⁻ state than in the 1Bu⁺ state have been shown.     

Impact of Fe3+ on UV absorption of K2Al2B2O7 crystals

K₂Al₂B₂O₇ (KABO) is a new nonlinear optical crystal capable of laser harmonic generation in the UV range. However, abnormal UV absorption prevents its application in effectively generating UV light with wavelength shorter than 300 nm. The transmittance spectra of the grown crystals show distinct absorption bands at 216 nm and 264 nm. It is observed that the UV absorption is strongly correlated with iron impurity at a parts per million (ppm) level. Furthermore, electron paramagnetic resonance (EPR) spectra of the absorbing crystals show a strong signal at g = 2.00 position corresponding to a Fe³⁺ center. A new crystal growth method which reduces the iron content has been proposed and results show that the new KABO crystal is free from the Fe³⁺ UV absorptions.     

Electronic structure and Raman spectroscopy study of dibarium magnesium orthoborate,Ba2Mg(BO3)2

The samples of dibarium magnesium orthoborate Ba₂Mg(BO₃)₂ were synthesized by solid-state reaction. The X-ray diffraction (XRD) patterns and Raman spectra of the samples were collected. Electronic structure and vibrational spectroscopy of Ba₂Mg(BO₃)₂ were systematically investigated by first principle calculation. A direct band gap of 4.4 eV was obtained from the calculated electronic structure results. The top valence band is constructed from O 2p states and the low conduction band mainly consists of Ba 5d states. Raman spectra for Ba₂Mg(BO₃)₂ polycrystalline were obtained at ambient temperature. The factor group analysis results show the total lattice modes are 5E_u + 4A_2u + 5E_g + 4A_1g + 1A_2g + 1A_1u, of which 5E_g + 4A_1g are Raman-active. Furthermore, we obtained the Raman active vibrational modes as well as their eigenfrequencies using first-principle calculation. With the assistance of the first-principle calculation and factor group analysis results, Raman bands of Ba₂Mg(BO₃)₂ were assigned as E_g (42 cm⁻¹), A_1g (85 cm⁻¹), E_g (156 cm⁻¹), E_g (237 cm⁻¹), A_1g (286 cm⁻¹), E_g (564 cm⁻¹), A_1g (761 cm⁻¹), A_1g (909 cm⁻¹), E_g (1165 cm⁻¹). The strongest band at 928 cm⁻¹ in the experimental spectrum is assigned to totally symmetric stretching mode of the BO₃ units.     

Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Optimization of parameters of sampling and determination of reduced sulfur compounds using cryogenic capture and gas chromatography in tropical urban atmosphere

Reduced sulfur compounds, RSCs (H₂S, COS, CH₃SH, CH₃SCH₃, CS₂ and CH₃S₂CH₃) play a role in global cycle and acid rain formation. At trace levels RSCs in air are difficult to collect, store and analyze because of their highly adsorptive and reactive properties. This work optimizes parameters of sampling and instrumental determination of RSCs for urban measurements. The method used is based on cryogenic sampling and gas chromatography provided with a cryofocusing trap and flame photometric detection.Greater sampling efficiency was obtained with liquid argon as freezing fluid and air flow rate of 150 mL min^? 1 for two hours. Best results have been obtained with preconcentration for 3 min and injection volume of 3 ml. For H₂S, CH₃SH and CH₃S₂CH₃ the method showed a precision of 89%, limit of detection of 0.10 µg m^? 3 and limit of quantification 0.3 µg m^? 3. For CH₃SCH₃ and CS₂ the corresponding values were 89%, 0.15 µg m^? 3 and 0.5 µg m^? 3 and for COS were 75%, 0.18 µg m^? 3 and 0.8 µg m^? 3 respectively. Sampling efficiency varied between 70–80% for all the RSCs. Accuracy of H₂S from field measurements obtained with parallel measurements using a continuous monitor varied between 88 and 98%. The optimized methodology proved to be suitable for field measurements in urban tropical atmospheres with different characteristics.     

Macroporous Co3O4 platelets with excellent rate capability as anodes for lithium ion batteries

This paper reports the microwave-assisted synthesis of Co₃O₄ nanomaterials with different morphologies including nanoparticles, rod-like nanoclusters and macroporous platelets. The new macroporous platelet-like Co₃O₄ morphology was found to be the best suitable for reversible lithium storage properties. It displayed superior cycling performances than nanoparticles and rod-like nanoclusters. More interestingly, excellent high rate capabilities (811 mAh g^?1 at 1780 mA g^?1 and 746 mAh g^?1 at 4450 mA g^?1) were observed for macroporous Co₃O₄ platelet. The good electrochemical performance could be attributed to the unique macroporous platelet structure of Co₃O₄ materials.     

Jahn–Teller coupling and the influence of strain in Tg and Eg ground and excited states – A ligand field and DFT study on halide MIIIX6 model complexes [M = TiIII–CuIII; X = F−, Cl−]

In contrast to well established experimental results of vibronic coupling effects in octahedral dⁿ complexes with E_g ground states (Cu²⁺, Ag²⁺; Cr²⁺, Mn³⁺ etc.), not much useful material is available for the Jahn–Teller (JT) effect in orbital triplet ground states. The present study is concerned with this deficiency, providing data for octahedral halide model complexes with 3dⁿ cations – in particular for Ti^III, V^III and high-spin Co^III, Ni^III with T_2g and T_1g ground states, which involve, to first-order, solely splitting of the π-antibonding t_2g MOs. Besides experimental results – structural and spectroscopic, mainly from d–d spectra – data from computations are needed for a quantitative treatment of the T_g ? (?_g + τ_2g) vibronic interaction as well as in the E_g ? ?_g coupling case (Mn^III, low-spin Ni^III); DFT was the method of choice, if only critically selected outcomes are utilised. The theoretical bases of the treatment are the dⁿ ligand field matrices in O_h, extended by the inclusion of lower-symmetry distortion parameters, and the conventional theory of vibronic coupling. Caution is needed when classifying the effects of interelectronic repulsion; DFT does not reproduce the magnitudes of the Racah parameters B, C, as deduced from the d–d spectra, properly – the presumed reasons are analysed. DFT even allows one to deduce reliable vibronic coupling constants via the analysis of orbitally degenerate excited states (Cr^III, ⁴A_2g ground state). The group-theoretical analysis of the interaction with the JT-active ?_g and τ_2g modes yields D_4h, D_3d and D_2h as the possible distortion symmetries in the case of a T_g ground state. The DFT-calculations give clear evidence, that the D_4h stationary points represent the absolute minima in the T_g ? (?_g + τ_2g) potential surface – in agreement with experiment, where available. For the first time, vibronic coupling constants, characterising JT splitting of ground and excited T_g states, can be presented for trivalent 3dⁿ cations in octahedral halide ligand fields. They turn out to be smaller by a factor of almost 3 in comparison to those, which determine the coupling in σ-antibonding e_g MOs.The tetragonal splitting of T_g states is typically only small, around 0.1 eV, and suggests that strain influences from a specific ligand arrangement and/or the presence of different ligands may modify the potential surface considerably. We have studied such effects via compounds A^IM^IIIF₄, where an elastic strain induced by the host structure, and a binding strain, due to the simultaneous existence of (largely) terminal and of bridging ligands, are active. A novel strain model, in its interplay with JT coupling, is proposed and applied – using energies from the d–d spectra, structural results and data from DFT.Chloride complexes are only known for Ti^III to Fe^III; the rather small electronegativity already of Co^III suggests a reducing ligand-to-metal (3dⁿ) electron transfer for n ≥ 6. Similarly, the low-lying ligand-to-metal charge transfer bands in the d–d spectra of the Cu^IIIF₆^3? complex and the reduced T_g ? ?_g coupling strength suggest a pronounced covalency of the Cu^III–F, and, even more distinctly, of the Cu^III–O bond, which is of interest for superconductivity. The Ni^IIIF₆^3? polyhedron possesses a low-spin configuration in the elpasolite structure. The spectroscopic evidence and the DFT data indicate, that the minimum positions of the alternative _a²A_1g(_a²E_g) and _a⁴A_2g (_a⁴T_1g) potential curves are only ≤0.02 eV apart, giving rise to interesting high-spin/low-spin phenomena. It is the strong E_g ? ?_g as compared to the T_1g ? ?_g coupling, which finally stabilises a spin-doublet ground state in D_4h.We think, that the selected class of solids is unique particularly for the study of Jahn–Teller coupling in T ground states, with model character for other systems. In our overview a procedure is sketched, which uses reliable computational results (here from DFT) for supplementing incomplete experimental data, and presents – on a semiquantitative scale – convincing statements, consistent with chemical intuition. It is also a pleading for ligand field theory, which rationalises d-d spectra in terms of chemical bonding; though the latter spectra provide frequently only rather coarse information, their assistance in the energy analysis is crucial.     

Selective extraction of traffic-related antimony compounds for speciation analysis by graphite furnace atomic absorption spectrometry

Most traffic-related antimony air pollutants are derived from brake dust. Brake dust contains Sb₂S₃, used as a friction material in brake pads, and its high-temperature oxidation products, Sb₂O₃ or Sb₂O₄. Systematic investigations were carried out to find the most selective leaching conditions for these substances. First, solubility experiments of the pure potential compounds mentioned above were carried out. Then, the leaching of these compounds from home-made artificial dusts previously spiked with these compounds at the trace level was investigated. A 0.5 mol L^?1 citric acid solution proved to leach the whole Sb₂O₃ content while extracting less than 10% Sb₂S₃ and no Sb₂O₄ at all. It was found that Sb₂O₃ and Sb₂S₃ traces were soluble in a 6 mol L^?1 HCl solution, quantitatively and selectively. Graphite furnace atomic absorption spectrometry and hydride generation graphite furnace atomic absorption spectrometry methods were developed to determine the Sb content of the extracts. The proposed method proved to be applicable to settled dust containing traffic-related Sb compounds. The detection limits were 1.2 and 0.3 μg g^?1 for leaching by citric acid and HCl solution, respectively, which were adequate for Sb content determination in the urban dust studied. The reproducibility of the method expressed as relative standard deviation was about 7%. The results showed that the concentration of leachable Sb was 40 μg g^?1 in the settled dust of Budapest, about half of which corresponded to Sb₂O₃. The Sb₂O₄ content calculated as the difference of total and leachable fraction was about 10% with high uncertainty.     

Electrodeposited PbO2 thin film on Ti electrode for application in hybrid supercapacitor

PbO₂ thin films were prepared by pulse current technique on Ti substrate from Pb(NO₃)₂ plating solution. The hybrid supercapacitor was designed with PbO₂ thin film as positive electrode and activated carbon (AC) as negative electrode in the 5.3 M H₂SO₄ solution. Its electrochemical properties were determined by cyclic voltammetry (CV), charge–discharge test and electrochemical impedance spectroscopy (EIS). The results revealed that the PbO₂/AC hybrid supercapacitor exhibited large specific capacitance, high-power and stable cycle performance. In the potential range of 0.8–1.8 V, the hybrid supercapacitor can deliver a specific capacitance of 71.5 F g^?1 at a discharge current density of 200 mA g^?1(4 mA cm^?2) when the mass ratio of AC to PbO₂ was three, and after 4500 deep cycles, the specific capacitance remains at 64.4 F g^?1, or 32.2 Wh Kg^?1 in specific energy, and the capacity only fades 10% from its initial value.     

A Raman spectroscopic study of the mineral coquandite Sb6O8(SO4)·(H2O)

Raman spectra of coquandite Sb₆O₈(SO₄)·(H₂O) were studied, and related to the structure of the mineral. Raman bands observed at 970, 990 and 1007 cm^?1 and a series of overlapping bands are observed at 1072, 1100, 1151 and 1217 cm^?1 are assigned to the SO₄^2? ν₁ symmetric and ν₃ antisymmetric stretching modes respectively. Raman bands at 629, 638, 690, 751 and 787 cm^?1 are attributed to the SbO stretching vibrations. Raman bands at 600 and 610 cm^?1 and at 429 and 459 cm^?1 are assigned to the SO₄^2? ν₄ and ν₂ bending modes. Raman bands at 359 and 375 cm^?1 are assigned to O–Sb–O bending modes. Multiple Raman bands for both SO₄^2? and SbO stretching vibrations support the concept of the non-equivalence of these units in the coquandite structure.     

A Raman spectroscopic study of the antimonite mineral peretaite Ca(SbO)4(OH)2(SO4)2·2H2O

Raman spectra of mineral peretaite Ca(SbO)₄(OH)₂(SO₄)₂·2H₂O were studied, and related to the structure of the mineral. Raman bands observed at 978 and 980 cm^?1 and a series of overlapping bands observed at 1060, 1092, 1115, 1142 and 1152 cm^?1 are assigned to the SO₄^2? ν₁ symmetric and ν₃ antisymmetric stretching modes. Raman bands at 589 and 595 cm^?1 are attributed to the SbO symmetric stretching vibrations. The low intensity Raman bands at 650 and 710 cm^?1 may be attributed to SbO antisymmetric stretching modes. Raman bands at 610 cm^?1 and at 417, 434 and 482 cm^?1 are assigned to the SO₄^2? ν₄ and ν₂ bending modes, respectively. Raman bands at 337 and 373 cm^?1 are assigned to O–Sb–O bending modes. Multiple Raman bands for both SO₄^2? and SbO stretching vibrations support the concept of the non-equivalence of these units in the peretaite structure.     

Characterization,EPR and photoluminescence studies of LiAl5O8:Cr phosphors

Red emitting Cr³⁺ doped LiAl₅O₈ powder phosphor was prepared by combustion route using corresponding metal nitrates and urea in a single step. The prepared powder was characterized by X-ray diffraction and surface area measurements were carried out by Brunauer–Emmet–Teller adsorption isotherms. The electron paramagnetic resonance spectrum in the low field regions is typical for isolated Cr³⁺ ions whereas the resonance signal in the high field region with g = 1.95 is due to exchange coupled Cr³⁺–Cr³⁺ pairs. The optical studies show two broad and intense bands characteristic of Cr³⁺ ions in distorted octahedral symmetry. The photoluminescence spectrum gives a narrow red emission at 710 nm corresponding to ²E_g → ⁴A_2g transition upon excitation of 562 nm. The crystal field parameter (Dq), Racah inter-electronic repulsion parameters (B and C) and nephelauxetic parameters have been evaluated and discussed.     

Bi2O3 deposited on highly ordered mesoporous carbon for supercapacitors

A simple route has been employed to prepare nanosized Bi₂O₃ deposited on highly ordered mesoporous carbon. The electrochemical measurements reveal that, by loading only 10% Bi₂O₃ on the mesoporous carbon, the specific capacitance of the composite is improved by 62%, with the maximum value reaching 232 F g^?1 at a sweep rate of 5 mV s^?1. The specific capacitance of Bi₂O₃ is calculated and reaches 1305 F g^?1 at 1 mV s^?1. It is found that the mass transfer in the framework of the crystalline oxide is still difficult in spite of its nanosize, as evidenced by the decline of the specific capacitance of the Bi₂O₃ with the increase of the sweep rate. The cyclic life of composite materials is also measured and the capacitance only declines 21% after 1000 cycles.     

EPR and optical absorption studies of Cu2+ doped bis (glycinato) Mg (II) monohydrate single crystals

Electron paramagnetic resonance (EPR) study of Cu²⁺ doped bis (glycinato) Mg (II) monohydrate single crystals is carried out at room temperature. Copper enters the lattice substitutionally and is trapped at two magnetically inequivalent sites. The observed spectra are fitted to a spin-Hamiltonian of rhombic symmetry with the following values of the parameters: Cu²⁺ (I), g_x = 2.1577 ± 0.0002, g_y = 2.2018 ± 0.0002, g_z = 2.3259 ± 0.0002, A_x = (87 ± 2) × 10^?4 cm^?1, A_y = (107 ± 2) × 10^?4 cm^?1, A_z = (141 ± 2) × 10^?4 cm^?1; Cu ²⁺ (II), g_x = 2.1108 ± 0.0002, g_y = 2.1622 ± 0.0002, g_z = 2.2971 ± 0.0002, A_x = (69 ± 2) × 10^?4 cm^?1, A_y = (117 ± 2) × 10^?4 cm^?1and A_z = (134 ± 2) × 10^?4 cm^?1. The ground state wave function of the Cu²⁺ ion in this lattice is evaluated to be predominantly |x² ? y². The g-factor anisotropy is also calculated and compared with the experimental value. With the help of the optical absorption study, the nature of bonding in the complex is discussed.     

Nano TiO2-based preconcentration for the speciation analysis of inorganic selenium by using ion chromatography with conductivity detection

A simple, sensitive, and cost-effective analytical method was developed for the speciation analysis of inorganic selenium by combining a nano-TiO₂ preconcentration with an ion chromatography-conductivity detection (IC-CD) system. The experimental conditions for the simultaneous adsorption and desorption of Se(IV) and Se(VI) were carefully investigated. Under the established optimum condition, the Se(IV) and Se(VI) ions could been simultaneously adsorbed onto the nano-TiO₂ surface at pH 4.0, and then effectively desorbed by 0.1 M sodium hydroxide eluent. The adsorption process was fast and reached adsorption equilibrium within 10 min. The nano-TiO₂ also exhibited high adsorption capacity with 11.3 mg g^? 1 for Se(IV) and 8.34 mg g^? 1 for Se(VI). The enrichment factors for Se(IV) and Se(VI) were calculated to be 39 and 30, respectively, with sample volume of 50 mL. The detection limits (3σ) were 0.8 μg L^? 1 for Se(IV) and 0.4 μg L^? 1 for Se(VI), which were sensitive enough for the routine analysis of water and drink samples. The relative standard deviation was calculated to be < 4% (n = 6) for detection of 30 μg L^? 1 Se(IV) and 30 μg L^? 1 Se(VI). The results of the present work confirmed that our developed nano-TiO₂-IC-CD method could be applied for the detection of inorganic selenium species in tap water and drink samples with good recoveries in the range of 82%–108%.     

Li2ZnTi3O8 nanorods: A new anode material for lithium-ion battery

Spinel Li₂ZnTi₃O₈ nanorods were first synthesized using titanate nanowires as a precursor. The synthesized nanorods are highly crystalline and used as an anode material in a rechargeable Li-ion battery. A large capacity of 220 mA h g^? 1 was kept after 30 cycles at a current density of 0.1 A g^? 1, which is close to the theoretic capacity. The electrochemical measurements indicate that the anode material made of spinel Li₂ZnTi₃O₈ nanorods displayed a highly reversible capacity and excellent cycling stability.     

Spectroscopic properties of RBiBO4 (R = Ca,Sr) glasses doped with TiO2

Transparent glasses, melt quenching derived, containing 10RO·20Bi₂O₃·(70 ? x)B₂O₃·xTiO₂ [R = Ca, Sr] with x = 0, 0.5, 1.0 wt% were characterized by X-ray powder diffraction. Physical and spectroscopic properties viz., density, absorption, emission, electron paramagnetic resonance (EPR) and FTIR were investigated. The absorption band around 823 nm in pure glass samples is attributed to the electronic transition of ³P₀ to ³P₂ of Bi⁺ radicals. A small absorption hump centered around 609 nm is found in all doped glasses due to ²T_2g to ²E_g transition of octahedral Ti³⁺ ions. The emission results revealed that all the samples exhibit a broad emission band covering entire visible-light range, with λ_ex = 360 nm, centered 470–520 nm corresponds to electronic transition of ³P₁ to ¹S₀ of Bi³⁺ ions, therefore the present materials can be potentially used as tunable or full-color display systems. And a strong emission around 706 nm with λ_ex = 514 nm due to transition of ²P_3/2 to ²P_1/2 of Bi²⁺ ions. In SrO mixed glasses Ti⁴⁺ ions effect the environment of Bi³⁺ ion symmetry units from C₂ to C_3i. A small EPR signal (at room temperature) is observed in titanium doped glasses due to Ti³⁺ ions. In both the series with increase of TiO₂ concentration BO₄ units are gradually converted into BO₃ units and new cross linkages are formed, like B–O–Ti, Bi–O–Ti at the expense of B–O–B bonds.     

Synthesis of Co-containing mesoporous carbon foams using a new cobalt-oxo cluster as a precursor

A novel trinuclear cobalt-oxo cluster 2[Co₃O(Ac)₆(H₂O)₃]·H₂O (Co-OXO) has been obtained and characterized by X-ray single-crystal diffraction and elemental analysis. The structure of Co-OXO displays 3D supramolecular networks through hydrogen bonds and generates boron nitride (bnn) topology. Co-OXO was further used as a precursor to synthesize Co-containing mesoporous carbon foams (Co-MCFs), which exhibit highly ordered mesostructure with specific surface area of 614 m² g^?1 and uniform pore size of 2.7 nm. Charge–discharge tests show that the specific discharge capacitance of Co-MCFs is 7% higher than that of the MCFs at the current density of 100 mA g^?1, and 26% higher than that of MCFs at the current density of 3 A g^?1. The electrochemical behaviors of Co-MCFs are obviously improved due to the improved wettability, increased graphitization degree and the pseudo-capacitance through additional faradic reactions arising from cobalt.     

Temperature dependent Raman study of SB → SC transition in liquid crystalline compound N-(4-n-pentyloxybenzylidene)-4′-heptylaniline (5O.7)

Temperature dependent Raman study of C–H in-plane bending mode (～1163 cm^?1 and ～1190 cm^?1) and C–C stretching mode of phenyl ring (～1571 cm^?1 and ～1594 cm^?1) of N-(4-n-pentyloxybenzylidene)-4′-heptylaniline (5O.7) has been done. Vibrational assignment and potential energy distribution (PED) of individual modes have been calculated employing density functional theory (DFT) for the first time. The S_B → S_C transition is nicely depicted in the variation of the linewidth of the ～1163 cm^?1 band and the peak position of ～1594 cm^?1 band with temperature. Because of a small amount of charge density transfer from the core part to the alkyl chain region, the ～1163 cm^?1 band shifts towards lower wavenumber side whereas the ～1190 cm^?1 band towards higher wavenumber side at S_B → S_C transition. The ～1571 cm^?1 and ～1594 cm^?1 bands are assigned as 8a and 8b modes, whose relative intensity variation with temperature gives the evidence of increased possibility of C–H bending motion of the linking group and the C–C stretching of the alkyl chain in S_C phase.     

High capacity and excellent cyclability of vanadium (IV) oxide in lithium battery applications

A VO₂ · 0.43H₂O powder with a flaky particle morphology was synthesized via a hydrothermal reduction method. It was characterized by scanning electron microscopy, electron energy loss spectroscopy, and thermogravimetric analysis. As an electrode material for rechargeable lithium batteries, it was used both as a cathode versus lithium anode and as an anode versus LiCoO₂, LiFePO₄ or LiNi_0.5Mn_1.5O₄ cathode. The VO₂ · 0.43H₂O electrode exhibits an extraordinary superiority with high capacity (160 mAh g^?1), high energy efficiency (95%), excellent cyclability (142.5 mAh g^?1 after 500 cycles) and rate capability (100 mAh g^?1 at 10 C-rate).