高效膜色谱的发展和应用

对新兴的高效膜色谱的基质材料、膜形态、分离机理以及应用进行了综述,并对其用于对映体分离作了展望。共７６篇。     

SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30 wt%)、SPEEK/SPES-C(30 wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7 cm2·s-1数量级上,远小于Nation[R]115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20 wt%)共混膜电导率超过Nation[R]115膜;温度大于110℃时,SPEEK/SPES-C(30 wt%)共混膜电导率与Nafion[R]115膜相当,达到0.11 S·cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.     

LaCo(1-x)Ni(x)O(3) with Improved Electrical Conductivity

To determine the applicability of LaCo(1-x)Ni(x)O(3) in a conductive material for electrical wiring, the dependence of the electronic transport property on the Ni content is investigated via Hall effect measurements, Rietveld analyses, and band-structure calculations. Ni doping (50 mol %) into the Co sites realizes a high electrical conductivity of 1.9 × 10(3) S/cm, which is an unexpectedly high value for a LaCo(1-x)Ni(x)O(3) system, at room temperature due to the high carrier concentration of 2.2 × 10(22) cm(-3) and the small effective mass of 0.1 m(e). In addition, the high electrical conductivity is maintained from room temperature to 900 °C; that is, the temperature coefficient of the conductivity is smaller than that of standard metals. Thus, the results indicate that LaCo(0.5)Ni(0.5)O(3) is suitable as a conductive material for electrical wiring at high temperatures in air.     

Water-Soluble Polypeptides with Elongated, Charged Side Chains Adopt Ultra-Stable Helical Conformations

Water-soluble polypeptides adopting α-helical conformations with unprecedented high helicities were obtained by elongating the charge-containing side chains of the constituent amino acids to allow the terminal charges to be situated distally from the peptide backbone. Poly(γ-(4-aminoethylthiopropoxyl)-benzyl-(L)-glutamate) (PAOBLG-AET) with a charge-peptide backbone distance of 17 σ-bonds exhibited a remarkably high helical content (81%) at a degree of polymerization as low as 10. The helical conformations of these short polypeptides were very stable against various harsh, protein-denaturing conditions, such as extreme pH, high temperature, and high salt or urea concentrations.     

Mesoporous TiO2 core-shell spheres composed of nanocrystals with exposed high-energy facets: facile synthesis and formation mechanism

A facile new method that combines electrospray and hydrothermal treatment is used to prepare mesoporous core-shell TiO(2) spheres with high specific surface areas and high pore volumes. Interestingly, the resulting TiO(2) spheres are composed of anatase TiO(2) nanocrystals with exposed step-like {001} and smooth {010} facets. The percentage of exposed {001} facets can be adjusted by changing the experimental parameters used in the electrospray and hydrothermal treatment processes, such as the contents of poly(N-vinyl-2-pyrrolidone) and acetic acid. The combination of high specific surface area (>100 m(2) g(-1)), high pore volume (>0.30 cm(3) g(-1)), useful pore size (10-15 nm), spherical core-shell structure, and exposed high energy facets makes these TiO(2) spheres an important candidate for use in many photoelectrochemical applications. The formation mechanism of the mesoporous TiO(2) spheres is also studied. The great advantage of this method is that interesting and complicated mesoporous superstructures can be prepared using electrospray technology.     

Highly diastereoselective heterogeneously catalyzed hydrogenation of enamines for the synthesis of chiral beta-amino acid derivatives

Pure (Z)-enamines readily prepared from beta-ketoesters and amides using (S)-phenylglycine amide were hydrogenated with very high diastereoselectivities (up to 200:1) using heterogeneous catalysis. Hydrogenolytic cleavage of the (S)-phenylglycine amide afforded the corresponding chiral beta-aminoesters and amides. The high geometrical purity of the (Z)-enamine and a simple activation procedure for the PtO2 catalyst are essential in achieving high selectivity.     

Application of capillary electrophoresis in peptide research.

Comparison of high performance liquid chromatograms (HPLC) with capillary electrophoresis shows the latter to be superior in many cases owing to rapid separation, high resolution and high sensitivity. This is demonstrated with two examples (i) the isolation of natural peptides from bovine tissue and (ii) characterization of a synthetic peptide mixture with the natural sequence (fragment) of the human immunodeficiency virus (HIV) transmembrane glycoprotein gp 41 env.     

Catalytic asymmetric intramolecular hydroamination of alkynes in the presence of a catalyst system consisting of Pd(0)-methyl Norphos (or tolyl Renorphos)-benzoic acid

Enantiomerically pure methyl Norphos (A), tolyl Norphos (B), CF(3) Norphos (C), methyl Renorphos (D), and tolyl Renorphos (E) were synthesized and used as chiral bisphosphine ligands for the catalyst system, Pd(2)(dba)(3) x CHCl(3)/PhCOOH, in an intramolecular hydroamination of aminoalkynes 15. Among the Norphos series, methyl Norphos (A) was the best ligand for the hydroamination, and the corresponding five- and six-membered nitrogen heterocycles 16 were obtained in high yields with high enantioselectivities. Among the Renorphos series, tolyl Renorphos (E) gave the best result; both methyl Norphos (A) and tolyl Renorphos (E) afforded high yields and high enantioselectivities. NMR investigation using Me-Norphos revealed that this ligand was oxidized gradually in the presence of Pd(2)(dba)(3).CHCl(3) in C(6)D(6) even under the conditions using Ar atmosphere to give Me-Norphos oxide, which prevented the intramolecular hydroamination. On the other hand, Me-Norphos was rather stable in C(6)D(6) in the absence of the palladium catalyst under Ar atmosphere and was not converted to its oxide even after 3 days. The gradual oxidation of ligands (A and E) in the presence of the Pd catalyst is perhaps a reason why 20 mol % of A or E was needed to obtain high yields and high ee's of 16.     

磺化聚醚醚酮/三羧基丁烷膦酸锆复合质子交换膜的研究

通过在磺化聚醚醚酮(SPEEK)中掺杂1,2,4-三羧基丁烷-2-膦酸锆(Zr(PBTC))制备出SPEEK/Zr(PBTC)复合质子交换膜.结果表明,与纯SPEEK膜相比,Zr(PBTC)的掺杂能降低复合膜的吸液量及甲醇透过系数,且随着Zr(PBTC)含量的增加,这种作用越趋明显.在室温至80℃范围内,复合膜的甲醇透过系数在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,当温度大于90℃时,含40wt%Zr(PBTC)的复合膜电导率超过Nafion115膜,并在160℃时达到0.36S.cm-1.使用温度的提高及在高温下的高电导率表明该复合膜适合在高温DMFC中使用.     

A study of physicochemical and biopharmaceutical properties of amoxicillin tablets using full factorial design and PCA biplot

The variables that influence the tablets obtained by direct compression method deserve to be studied to minimize formulations costs and to improve the physicochemical and biopharmaceutical properties of the compacts. Here, we explore the adjuvants effects on amoxicillin tablet formulations considering multiple responses, and indicate the most suitable formulation composition. A 2(3) full factorial design was built to different amoxicillin formulations, each one containing three replicate batches, and eight responses (physicochemical and biopharmaceutical parameters) were obtained. The microcrystalline cellulose (MCC) type Avicel PH-102 (low) or PH-200 (high), the absence (low) or presence (high) of spray-dried lactose (LAC), and the absence (low) or presence (high) of disintegrant (DIS) were the levels investigated. The more relevant responses to the distinct formulations from the experimental design were hardness, friability, and the amount of amoxicillin dissolved during the first hour. PCA biplot indicated high values of amount of drug dissolved in 60 min as advantageous responses for the investigated amoxicillin tablet formulations and high values of friability as not desirable. Considering the individual response evaluation, the most suitable amoxicillin tablet formulation should present in its composition the MCC type Avicel PH-102 (low level) and the superdisintegrant agent (DIS high level), croscarmellose sodium, but no LAC (low level).     

MCM-48介孔分子筛的高压合成

采用正硅酸乙酯（TEOS）作硅源,十六烷基三甲基溴化铵（CTAB）为模板剂,在高压 （约7 MPa）和373 K下合成了MCM-48介孔分子筛.用XRD、氮气吸附及29Si MAS NMR对样品 进行了表征.与常压合成的相比,高压下合成的MCM-48具有更高的热稳定性和水热稳定性.2 9Si MAS NMR结果表明,高压有利于分子筛孔壁的聚合,导致分子筛结构更加完善,从而使 其具有更高的稳定性.     

High pressure synthesis of late rare earth RFeAs(O,F) superconductors; R = Tb and Dy

New TbFeAs(O,F) and DyFeAs(O,F) superconductors with critical temperatures T(c) = 46 and 45 K and very high critical fields, >/=100 T, have been prepared at 1100-1150 degrees C and 10-12 GPa, demonstrating that high pressure may be used to synthesise late rare earth derivatives of the recently reported RFeAs(O,F) (R = La-Nd, Sm, Gd) high temperature superconductors.     

Chiral sulfoxides as neutral coordinate-organocatalysts in asymmetric allylation of N-acylhydrazones using allyltrichlorosilanes

Sulfoxides were first introduced to the allylation of N-acylhydrazones with allyltrichlorosilanes as effective neutral coordinate-organocatalysts (NCOs). Both high diastereo- and enantioselectivity were attained when optically active chiral sulfoxides were used. Asymmetric crotylations using (Z)- and (E)-crotyltrichlorosilanes showed a high level of stereospecificity (Z --> anti and E --> syn) with high enantioselectivity.     

High‐efficiency organic electroluminescent devices using iridium complex emitter and arylamine‐containing polymer buffer layer

We have developed efficient organic electroluminescent (EL) devices using a phosphorescent material, tris(2‐phenylpyridine) iridium, Ir(ppy)₃, as an emitter material and a polymer buffer layer, tetraphenyldiamine‐containing poly(arylene ether sulfone) (PTPDES) doped with tris(4‐bromophenyl) aminium hexachloroantimonate (TBPAH) as an electron acceptor. In this device, a high external quantum efficiency of 21.6% and a luminous efficiency of 82 lm/W (77 cd/A) at 3.0 V were obtained. These high efficiencies can be explained by high quantum efficiency due to phosphorescent Ir(ppy)₃ and high luminous efficiency realized by the use of the polymer buffer layer. Copyright © 2002 John Wiley & Sons, Ltd.     

A general and efficient method for the selective synthesis of beta-hydroxy sulfides and beta-hydroxy sulfoxides catalyzed by gallium(III) triflate

Gallium(III) triflate-catalyzed ring opening of epoxides affords beta-hydroxy sulfides with high regioselectivity and chemoselectivity in high yields (84-97%) under solvent-free conditions. Additionally, a simple, efficient, and environmentally benign one-pot procedure for the synthesis of beta-hydroxy sulfoxides in sole water has been developed for the first time. The process, promoted by a H2O2-Ga(OTf)3 system, affords beta-hydroxy sulfoxides in high yields (81-94%) and high chemoselectivity without any detectable overoxidation to beta-hydroxy sulfones. The catalyst could be recovered easily after the reactions and reused without evident loss of activity.     

Capillary electrophoresis-high resolution sector field inductively coupled plasma mass spectrometry

The background and applications of high resolution sector field inductively coupled plasma mass spectrometry (HR-ICP-MS) as a detector for capillary (CE) and gel electrophoretic separations are reviewed. Notable progress has been made in the fields of bioinorganic and environmental (geo-) chemistry. Metallomics, the study of metal species interactions and functions in biological systems, puts substantial technical demands on speciation analysis. The combination of high species resolving power (CE) and high sensitivity-high mass resolving power (HR-ICP-MS) provides a solid base to meet such demands.     

耐高温碳化硅纤维的制备与性能

采用聚硅碳硅烷（PSCS）与乙酰丙酮铝反应，合成出聚铝碳硅烷（PACS）陶瓷先驱体聚合物.经熔融纺丝、空气不熔化、烧成与高温烧结等工艺， 制备性能优异的耐高温碳化硅纤维SiC(Al).经29Si MAS NMR、 XRD、 Raman谱、AES与SEM等一系列分析表明，该纤维的化学组成和结构与普通碳化硅纤维显著不同，具有近化学计量比组成，氧、游离碳以及SixCyOz相的含量大大低于普通碳化硅纤维，这是其高温稳定的主要原因.在制备过程中铝作为烧结助剂起到了使纤维致密化与抑制晶粒快速增长的作用.     

Hexamethylenetetramine directed synthesis and properties of a new family of alpha-nickel hydroxide organic-inorganic hybrid materials with high chemical stability

A new family of organic-inorganic hybrid material of alpha-nickel hydroxide formulated as Ni(OH)2-x(An-)x/n-(C6H12N4)y.zH2O (A=Cl-, CH3COO-, SO4(2-), NO3-; x=0.05-0.18, y=0.09-0.11, z=0.36-0.43) with high stability and adjustable interlayer spacing ranging from 7.21 to 15.12 A has been successfully prepared by a simple hydrothermal method. The effects of various anions and hexamethylenetetramine (HMT) on the d values of alpha-nickel hydroxide have been systematically investigated. This family of hybrid materials is of such high stability that they can stand more than 40 days in 6 M KOH. The product with a formula Ni(OH)1.95(C6H12N4)0.11(Cl-)0.05(H2O)0.36 has a high surface area of about 299.26 m2/g and an average pore diameter of about 45.1 A. The coercivity (Hc) value is ca. 2000 Oe for the sample with a d spacing of 13.14 A. Moreover, the prepared alpha-Ni(OH)2 in our experiment is of high stability in strong alkali solution. Such high stability could be derived from strong chelating interactions between the Ni ions and HMT molecules with the interlayers. This high chemical stability could make this material more suitable for the applications.     

A highly active neodymium chloride isopropanol complex/modified methylaluminoxane catalyst for preparing polyisoprene with high cis-1,4 stereospecificity and narrow molecular weight distribution

<正>Neodymium chloride isopropanol complex(NdCl_3·3~iPrOH) activated by modified methylaluminoxane(MMAO) was examined in isoprene polymerization in hexane,with regards to Nd compounds,aluminum(Al) compounds,[Al]/[Nd] ratio,polymerization temperature and time.NdCl_3-3~iPrOH exhibited high activity producing polymers featuring high cis-1,4 stereospecificity(96%),very high molecular weight(M_n1.0×10~6) and fairly narrow molecular weight distribution (MWD,M_w/M_n2.0) simultaneously.In comparison,neodymium isopropoxide also showed high activity providing polymers with narrow MWD(M_w/M_n = 2.07),but somewhat low cis-1,4 content(ca.92%),while neodymium chloride had no activity under present polymerization conditions.The Al compounds affected the polymer yield in the order of Al(i-Bu)_3MMAOAl(i-Bu)_2H.MMAO as cocatalyst afforded polyisoprene with high M_n over 1.0×10~6,whereas as stronger chain transfer agent than MMAO,Al(i-Bu)_3 and Al(i-Bu)_2H yielded polymers with low M_n(1.0×10~5-8.0×10~5). NdCl_3·3~iPrOH/MMAO catalyst showed a fairly good catalytic activity even at relatively low[Al]/[Nd]ratio of 30,and the produced polymer remained high cis-1,4 content of 95.8%along with high M_n over 1.0×10~6 even at elevated temperatures up to 70℃.The polymerization rate is of the first order with respect to the concentration of isoprene.The mechanism of active species formation was discussed preliminarily.     

Highly diastereoselective Friedel-Crafts reaction of furans with 8-phenylmenthyl glyoxylate

The Friedel-Crafts reaction of (1R)-8-phenylmenthyl glyoxylate with variously substituted furans was found to be efficiently promoted by SnCl(4) or magnesium salts with high diastereoselectivities. MgBr(2) performs especially well under simple, undemanding conditions, giving both high yields and high diastereoselectivities (>90%). The reaction afforded chiral substituted furan-2-yl-hydroxyacetic acid esters, compounds of potentially high synthetic interest. [reaction: see text]