Bestimmung von Elementspuren in Reinst-Cadmium durch Atomabsorptions-Spektrometrie nach Anreicherung durch partielles Lösen der Matrix

Trace elements such as Ag, Au, Bi, Co, Cu, Fe, In, Ni, Pb, Pd, and Sn can be preconcentrated from high-purity cadmium by partial dissolution of the matrix. The samples are coated by a thin film of mercury and dissolved in hydrobromic acid up to a small residue. In this residue the trace elements are enriched with recoveries of more than 95%. The elements are determined by AAS. For 10 g Cd the factor of enrichment is about 10², and the limits of detection are in the range of 0.1 ppm. The relative standard deviation was calculated to be about 5%. Reasons influencing the recovery of the trace elements are discussed.     

Comparative PGAA and NAA results of geological samples and standards

Concentrations of major and trace elements in volcanic rock and soil samples, including geological standard reference materials, were determined by neutron activation analysis (NAA) and prompt gamma activation analysis (PGAA), both using the k ₀-standardization method. The paper highlights the different experimental procedures, such as sample preparation, data collection and spectrum evaluation. In geological samples, PGAA gives precise results for major elements (Si, Ti, Al, Fe, Mn, Mg, Ca, Na, K and—as a unique method—for H), for some of the light trace elements as B and Cl, as well as for Sc, S, Cr, Co, Ni, Cd, Nd, Sm and Gd. NAA is sensitive for the rare earth elements, and for many major (Ti, Al, Fe, Mn, Mg, Ca, Na, K) and trace elements (e.g.: Sc, V, Cr, Co, Ni, Cu, Zn, As, Se, Rb, Sr, Zr, As, Sb, Ce, Ba, Hf, Ta, W). For most major elements the results obtained by the two methods show good agreement. The comparison of the results obtained for trace elements is not always possible, since PGAA is less sensitive and concentrations are often below its detection limits. Nevertheless, the complementarity of NAA and PGAA allows nearly panoramic analysis of geological materials.     

Verbundverfahren zur Multielement-Spurenbestimmung in hochreinem Chrom nach Spuren—Matrix-Trennung

(Simultaneous determination of trace elements in high-purity chromium by inductively-coupled plasma/atomic emission spectrometry after matrix separation.) The production of high-purity metals requires routine determinations of elements in the ng g^?1 range. Procedures based on wet chemical separation of matrix and trace elements followed by inductively-coupled plasma/atomic emission spectrometry are suitable. The separation of 19 trace metals (Be, Bi, Ca, Cd, Co, Cu, Fe, La, Mg, Mn, Nb, Ni, Pb, Ta, Ti, Th, U, Zn and Zr) from high-purity chromium powder is described. The powder is dissolved in hydrochloric acid and oxidized with perchloric acid or alkaline hydrogen peroxide, and the trace elements are precipitated at pH 11–13 and collected on cellulose loaded with indium hydroxide or on cellulose-Hyphan. The detection limits of the total procedure vary from 10 ng g^?1 for cadmium to 600 ng g^?1 for zinc.     

Synthesis of novel chitosan resin derivatized with serine diacetic acid moiety and its application to on-line collection/concentration of trace elements and their determination using inductively coupled plasma-atomic emission spectrometry

A novel chelating resin functionalized with serine diacetic acid moiety was synthesized by using chitosan as base material, and applied to the collection/concentration of trace elements in environmental water samples, followed by the determination using inductively coupled plasma-atomic emission spectrometer (ICP-AES). The synthesized resin, crosslinked chitosan serine diacetic acid (CCTS-SDA), showed good adsorption behavior toward trace amounts of Cd, Pb, Cu, Ni, V, Ga, Sc, In, and Th in a wide pH range. Additionally, rare earth elements also can be retained on the resin at neutral pH region. The adsorbed elements can be easily eluted with 1 mol L⁻¹ of nitric acid, and their recoveries were found to be 90-100%. The CCTS-SDA was packed in a mini-column, which was then installed in a computer-controlled auto-pretreatment system (Auto-Pret System) for on-line trace elements collection and determination with ICP-AES. Experimental parameters which related to the improvement of sensitivity and reproducibility were optimized. The limits of detection (LOD) for 13 elements were found to be in sub-ppb level. The proposed method with CCTS-SDA resin was successfully applied to the determination of trace elements in river water samples. The method was validated by determining a certified reference material of river water, SLRS-4.     

Determination of sulfur and selected trace elements in metallothionein-like proteins using capillary electrophoresis hyphenated to inductively coupled plasma mass spectrometry with an octopole reaction cell

The determination of sulfur in biologically relevant samples such as metalloproteins is described. The analytical methodology used is based on robust on-line coupling between capillary electrophoresis (CE) and octopole reaction cell inductively-coupled plasma mass spectrometry (ORC–ICP–MS). Polyatomic ions that form in the plasma and interfere with the determination of S at mass 32 are minimised by addition of xenon to the collision cell. The method has been applied to the separation and simultaneous element-specific detection of sulfur, cadmium, copper, and zinc in commercially available metallothionein preparations (MT) and metallothionein-like proteins (MLP) extracted from liver samples of bream (Abramis brama L.) caught in the river Elbe, Germany. Instrumental detection limits have been calculated according to the German standard procedure DIN 32645 for the determination of sulfur and some simultaneously measured trace elements in aqueous solution. For sulfur detection limits down to 1.3 g L^–1 (³⁴S) and 3.2 g L^–1 (³²S) were derived. For the other trace elements determined simultaneously detection limits ranging from 300 ng L^–1 (⁵⁸Ni) to 500 ng L^–1 (⁶⁶Zn, ⁵⁵Mn) were achieved. For quantification of sulfur and cadmium in a commercially available MT preparation under hyphenated conditions the use of external calibration is suggested. Finally, the need for proper sample-preparation technique will be discussed.     

Kathodenstrahlpolarographische Bestimmung von Spurenelementen in Zinnchloriden

Zusammenfassung Eine Methode wird beschrieben, die die kathodenstrahlpolarographische Bestimmung von Spuren Ni, Pb, Mn, Co, Cu, Fe, Mo in Zinnchloriden in den Bereichen 10^–4% (Ni, Pb, Mn, Cu, Fe) und 10^–5% (Mo, Co) gestattet. Über den stark basischen Anionenaustauscher AG 1×8 wird das Zinn von den Spurenelementen getrennt.

---

Cathode-ray polarographic determination of trace elements in tin chlorides

A method is described for the cathode-ray polarographic detemination of traces of Ni, Pb, Mn, Co, Cu, Fe, and Mo in tin chlorides. Tin is separated from the trace metals by ion exchange on the strong basic anion-exchange resin AG 1×8. The detection limits are within the ranges of 10^–4% and 10^–5%.

     

Application of factor analysis and simplex technique to the optimization of a phosphate determination via molybdenum blue

Zusammenfassung Aus Reinst-Cadmium können durch partielles Lösen der Matrix die Elementspuren Ag, Au, Bi, Co, Cu, Fe, In, Ni, Pb, Pd und Sn angereichert werden. Dazu werden die Proben mit einem dünnen Quecksilberfilm überzogen und in Bromwasserstoffsäure bis auf einen kleinen Rest gelöst. Die im Löserückstand angereicherten Spuren werden durch Atomabsorptions-Spektrometrie bestimmt. Die relativen Standardabweichungen betragen etwa 0,05; die Anreicherungsausbeuten sind > 95%. Bei Einwaagen von 10 g Cadmium beträgt der Anreicherungsfaktor etwa 10²; die Nachweisgrenzen (3-Grenzen) liegen um 0,1 ppm. Der Einfluß der Lösebedingungen auf die Anreicherung wird diskutiert.

---

Determination of trace elements in high-purity cadmium by AAS after preconcentration by partial dissolution of the matrix

Trace elements such as Ag, Au, Bi, Co, Cu, Fe, In, Ni, Pb, Pd, and Sn can be preconcentrated from high-purity cadmium by partial dissolution of the matrix. The samples are coated by a thin film of mercury and dissolved in hydrobromic acid up to a small residue. In this residue the trace elements are enriched with recoveries of more than 95%. The elements are determined by AAS. For 10 g Cd the factor of enrichment is about 10², and the limits of detection are in the range of 0.1 ppm. The relative standard deviation was calculated to be about 5%. Reasons influencing the recovery of the trace elements are discussed.

     

Optimization of a glancing angle for simultaneous trace elemental analysis by using a portable total reflection X-ray fluorescence spectrometer

By using a portable total reflection X-ray fluorescence spectrometer with a 1 W X-ray tube, a specimen containing nanograms of Ca, Sc, Ti, V, Cr, Mn, Fe, and Ni is measured at several glancing angles of incident X-rays. Continuum X-rays are used as the excitation source. The intensities of the spectral background which degrades sensitivity to trace elements are decreased with a decrease of the glancing angle, and all these elements are detected at the glancing angle of 0.13° smaller than the critical angle for total reflection of the incident X-rays (0.20°). An optimum glancing angle for simultaneously detecting these trace elements is around 0.13°, and detection limits at 0.13° are sub-nanograms to ten nanograms.     

Inductively coupled plasma atomic emission spectrometric determination of 27 trace elements in table salts after coprecipitation with indium phosphate

The coprecipitation method using indium phosphate as a new coprecipitant has been developed for the separation of trace elements in table salts prior to their determination using inductively coupled plasma atomic emission spectrometry (ICP-AES). Indium phosphate could quantitatively coprecipitate 27 trace elements, namely, Be, Ti, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd, Pb, Sc, Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu, in a table salt solution at pH 10. The rapid coprecipitation technique, in which complete recovery of the precipitate was not required in the precipitate-separation process, was completely applicable, and, therefore, the operation for the coprecipitation was quite simple. The coprecipitated elements could be determined accurately and precisely by ICP-AES using indium as an internal standard element after dissolution of the precipitate with 5 mL of 1 mol L⁻¹ nitric acid. The detection limits (three times the standard deviation of the blank values, n = 10) ranged from 0.001 μg (Lu) to 0.11 μg (Zn) in 300 mL of a 10% (w/v) table salt solution. The method proposed here could be applied to the analyses of commercially available table salts.     

Extraction-chromatographic system TBP-HBr in radiochemical neutron activation analysis of high-purity materials

The extraction and extraction-chromatographic behaviour of a variety of elements in the TBP-HBr system with concentrations from 0.1 to 7M HBr has been studied. The results allowed the development of simple procedures for radiochemical neutron activation determination of 22 impurity elements (Na, K, Sc, Cr, Mn, Fe, Co, Ni, Cu, Ga, As, Se, Rb, Sr, Zn, Mo, Ag, Sb, Te, Ba, La, Hf and W) in high-purity cadmium and indium samples with detection limits from 1 g g^–1 for Fe and Zr to 0.01 ng g^–1 for Na, Sc, Mn with relative standard deviations < 0.15. To increase the selectivity of the extraction-chromatographic separation, use was made of extraction suppression and co-extraction effects. The procedure for the extraction-chromatographic separation of scandium from a number of other elements is described as an example. The procedure can be used for simultaneous quantitative separation of impurity radionuclides from radiation produced long-life scandium radionuclides in the neutron activation analysis of titanium and vanadium.     

Direct multielement determination of trace elements in boron carbide powders by direct current arc atomic emission spectrometry using a CCD spectrometer

The use of direct current arc atomic emission spectrometry (DC-arc-AES) with a CCD spectrometer for the direct determination of the trace impurities Al, Ca, Cr, Cu, Fe, Mg, Mn, Na, Ni, Si, Ti, and Zr in three well characterized boron carbide powders is described. The detection limits obtained by the procedure were found to be between 0.2 (Mg) and 25 (Na) ??g?g^?1 for the above elements. Three boron carbide powder samples with trace element concentrations between 0.9 (Cu) and 934 (Si) ??g?g^?1 for Al, Ca, Cr, Cu, Fe, Mg, Mn, Na, Ni, Si, Ti, and Zr ?? including the standard reference material ERM?-ED102 ?? were analyzed by DC-arc-AES. The relative standard deviations for 9 measurements when using 5.0?±?0.3?mg of the respective samples were found to vary from 6.2 to 27% for Al and Cu, respectively. The trace elements Al, Ca, Cr, Cu, Fe, Mn, Ni, Si, Ti and Zr could be determined in the standard reference material and their concentrations determined by DC-arc AES were found to be between 89 and 116% of the accepted values. Fe and Ti were determined by DC-arc AES in the three boron carbide samples as well as in Al₂O₃, BN, SiC, coal fly ash, graphite and obsidian rock. The correlation coefficients of the plots of the net intensities versus the accepted values over the concentration ranges from 18 to 1750 and from 6 to 8000???g?g^?1 are 0.999 and 0.990 for Fe and Ti, respectively.

Determination of trace amounts of cadmium, cobalt, chromium, iron, molybdenum, nickel, selenium, titanium, vanadium and zinc in blood and milk by neutron activation analysis

The concentrations of Cd, Co, Cr, Fe, Mo, Ni, Se, Ti, V and Zn in biological fluids, human blood serum and market milk were determined by neutron activation analysis, with enrichment by coprecipitation. The pre-concentration of these trace elements was accomplished by converting the dissolved trace metal ions into their pyrrolidinedithiocarbamate (1-pyrrolidinecarbodithioate) chelates, followed by coprecipitation with a metal carrier such as Ni, Pb or Bi. The coprecipitation was carried out prior to irradiation for the short-lived nuclides (V, Ti and Se) and after irradiation for the other elements. The validity of the method was checked using certified biological reference materials; the concentrations of trace elements found by the proposed method agreed well with the published certified data. The limits of detection for Cd, Co, Cr, Fe, Mo, Ni, Se (obtained through the long-lived isotope 75Se) and Zn under the present experimental conditions were found to be 5, 5, 10, 520, 5, 70, 10 and 150 ng, respectively, for 5 ml of biological liquor. The limits of detection for Ti and V obtained (through their short-lived radionuclides 51Ti and 52V, respectively) were found to be 180 and 1.4 ng, respectively, for 50 ml of market milk, or 70 and 0.7 ng for 1 ml of blood serum.     

Multielement trace analysis of high purity aluminium by neutron activation

Instrumental neutron activation analysis was applied to multielement trace analysis of high purity aluminium samples. In order to reduce the production of²⁴Na from the matrix, samples were activated by thermal neutron flux of high cadmium ratio. Detection limits of various impurity elements were evaluated. So called “five nine” class standard aluminium samples were analyzed and concentrations of various impurity elements were determined. The analytical results obtained on zone refined aluminium samples showed that zone refining is effective against many elements, such as Na, Cr, Fe, Co, Cu, Ga, As, Br, Ba, La, Ce, Sm, Yb, Lu, Hf, W, Th and U, but not very effective against the element Sc.     

The determination of dissolved manganese and cadmium in sea water at low nmol 1−1 concentrations by chelation and extraction followed by electrothermal atomic absorption spectrometry

The development and application of a method suitable for the determination of dissolved manganese and cadmium in sea water at the low concentrations typical of the open ocean is described. A mixed dithiocarbamate/Freon TF extraction system is used to separate trace metals from major constituents, prior to back extraction into a final dilute nitric acid solution and subsequent determination of the metals by graphite-furnace atomic absorption spectrometry. The procedure also separates dissolved Co, Cu, Fe, Ni, Pb and Zn from a sea-water matrix. A mechanized system for the extraction step and measures to control contamination are described. The detection limits (3 σ) for manganese and cadmium are 0.10 and 0.04 nmol l^?1, respectively.     

Chelating resins for the concentration of trace elements from sea water and their analytical use in conjunction with atomic absorption spectrophotometry

An investigation has been made of the uptake of trace elements from both distilled water and sea water by the chelating ion-exchange resins Chelex-100 and Permutit S1005. The resins retained the following elements with an efficiency of ca. 100%: Ag, Bi, Cd, Cu, In, Pb, Mo, Ni, rare earths, Re (90% only), Sc, Th, W, V, Y and Zn. Manganese was retained quantitatively only by the Chelex resin. The following elements are removed with 100% efficiency by means of₂N mineral acids: Bi, Cd, Co, Cu, In, Ni, Pb, rare earths, Sc, Th, Y and Zn. Ammonia (4 N) completely removes molybdenum, tungsten, vanadium and rhenium. The resins have been used in conjunction with atomic absorption spectrophotometry for the simultaneous determination of zinc, cadmium, copper, nickel and cobalt in sea waters.     

Disposable Bismuth Oxide Screen Printed Electrodes for the High Throughput Screening of Heavy Metals

We present a simplified approach for the trace screening of toxic heavy metals utilizing bismuth oxide screen printed electrodes. The use of bismuth oxide instead of toxic mercury films facilitates the reliable sensing of lead(II), cadmium(II) and zinc(II). A linear range over 5 to 150 μg L^?1 with detection limits of 2.5 and 5 μg L^?1 are readily observed for cadmium and lead in 0.1 M HCl, respectively. Conducting a simultaneous multi‐elemental voltammetric detection of zinc, cadmium and lead in a higher pH medium (0.1 M sodium acetate solution) exhibited a linear range between 10 and 150 μg L^?1 with detection limits of 5, 10 and 30 μg L^?1 for cadmium, lead and zinc respectively. The sensor is greatly simplified over those recently reported such as bismuth nanoparticle modified electrodes and bismuth film coated screen printed electrodes. The scope of applications of this sensor with the inherent advances in electroanalysis coupled with the negliable toxicity of bismuth is extensive allowing high throughput electroanalysis.     

Neutron activation analysis of PbxSn1-xTe using extraction chromatography

A simple procedure of neutron activation analysis for the determination of 16 impurities in Pb_xSn_1–xTe with detection limits from 1×10^–4% for Ni and Zr to 2×10^–9% for Sc has been developed. The procedure is based on extraction chromatographic separation of impurities from the irradiated sample.     

环形聚焦单模微波消解–ICP–MS法检测罐头食品中钒、铬、镍、镉、铅、砷、锰、铝、铜、锡

建立环形聚焦单模微波消解–电感耦合等离子体质谱法同时测定罐头食品中钒、铬、镍、镉、铅、砷、锰、铝、铜、锡金属元素的含量。采用浓硝酸消解样品,各元素分析目标物分别为Pb208,Cd111,As75,Mn55,Cu63,V51,Ni60,Sn120,Cr53,Al27。Pb208以Bi209为内标,Cd111,Sn120以In115为内标,Ni60,Cr53,V51,Mn55,Cu63,As75,Al27以Sc45为内标。各元素工作曲线线性良好,相关系数不小于0.999 5,方法检出限为0.0030~0.030μg/g,加标回收率在98.0%~104.1%之间,测定结果的相对标准偏差为1.29%~4.50%(n=6)。该方法简便快捷,灵敏度高,适合分析大批量罐头食品中多种金属元素。     

A solid phase extraction using a chelate resin immobilizing carboxymethylated pentaethylenehexamine for separation and preconcentration of trace elements in water samples

A chelate resin immobilizing carboxymethylated pentaethylenehexamine (CM-PEHA resin) was prepared, and the potential for the separation and preconcentration of trace elements in water samples was evaluated through the adsorption/elution test for 62 elements. The CM-PEHA resin could quantitatively recover various elements, including Ag, Cd, Co, Cu, Fe, Ni, Pb, Ti, U, and Zn, and rare earth elements over a wide pH range, and also Mn at pH above 5 and V and Mo at pH below 7. This resin could also effectively remove major elements, such as alkali and alkaline earth elements, under acidic and neutral conditions. Solid phase extraction using the CM-PEHA resin was applicable to the determination of 10 trace elements, Cd, Co, Cu, Fe, Mn, Mo, Ni, Pb, V, and Zn, in certified reference materials (EnviroMAT EU-L-1 wastewater and ES-L-1 ground water) and treated wastewater and all elements except for Mn in surface seawater using inductively coupled plasma atomic emission spectrometry. The detection limits, defined as 3 times the standard deviation for the procedural blank using 500 mL of purified water (50-fold preconcentration, n = 8), ranged from 0.003 μg L⁻¹ (Mn) to 0.28 μg L⁻¹ (Zn) as the concentration in 500 mL of solution.     

Silberhalogenide als Spurenfänger für Chelatkomplexe

The power of detection of flame AAS for trace elements decreases considerably in presence of manganese. For the purity control of manganese and manganese compounds, therefore, it is necessary to separate the traces from the main component of the samples. For that purpose the traces were complexed by 1,10-phenanthroline and coprecipitated by silver iodide as trace collector. To receive a trace solution of 10 ml being free of manganese the filtered AgI was boiled with HNO₃. The enriched elements (Fe, Co, Ni, Cu, Zn, Cd, Pb, Bi and Tl) were determined by flame AAS. Using samples of 5 to 10 g of manganese or manganese compounds of different stages of oxidation the limits of detection of the various elements were found to be in a range between 0.01 and 1 ppm. By evaporation of the trace solution down to 1 ml and determination of the traces by the “injection method” of flame AAS limits of detection are obtained between 0.007 and 0.1 ppm.