Thiophosphate esters of cashew nutshell liquid derivatives as new antioxidants for poly(methyl methacrylate)

In this work, poly(methyl methacrylate) films 1% additivated with new thiophosphate esters antioxidants derived from technical Cashew Nutshell Liquid (CNSL), a byproduct of the cashew nut (Anacardium occidentale L.) industry, were investigated by thermogravimetry (TG/DTG) and differential scanning calorimetry (DSC) measurements under inert (N₂) and oxidative (synthetic air) atmospheres. Three new products were synthesized and characterized by GC/MS, ¹H and ³¹P NMR. The analyses were focused on the onset (T _e) and offset temperature (T _o) of degradation of the films, and on the maximum degradation temperature (T _MAX). It was observed that the thermal stability of the films increased with the addition of the thiophosphate ester antioxidants, which indicates that CNSL could be used as a natural source of phenolic material for the synthesis of antioxidants.     

Thermal expansion of oriented poly(methyl methacrylate)

The thermal expansivities along (α∥) and perpendicular (α_⊥) to the draw direction of poly(methyl methacrylate) (PMMA) with extrusion draw ratios 1 ≤ λ ≤ 4 have been measured between 150 and 298 K. As λ was increased from 1 to 4, α∥ decreased 2–3 times, whereas α_⊥ increased only 20–35%. The orientation function f calculated from thermal expansivity using the aggregate model is found to change linearly with birefringence, indicating that each property provides a sensitive measure of molecular orientation. For PMMA, however, only thermal expansivity can give an absolute f, with results at 150 K in reasonable agreement with previous studies using other techniques. At higher temperature, i.e., above ambient, PMMA side-group motions are excited, expanding volume, and calculations based on the aggregate model may not be valid.     

Thermal degradation of phosphonated poly(methyl methacrylate)

On heating at volatilisation temperatures, poly(methyl methacrylate) (PMMA) and diethoxyphosphonated poly(methyl methacrylate) (Ph.PMMA) behave differently in the very early stage of the degradation process. The volatilisation rate of PMMA decreases slowly with conversion whereas Ph.PMMA polymers volatilise at a high initial rate which decreases quickly with conversion.The overall volatilisation rate of Ph.PMMA polymers in this stage is much lower than that of PMMA. This is attributed to the formation of anhydride in degrading Ph.PMMA by intramolecular cyclisation which forms high boiling chain fragments.     

Thermal analysis of poly(methyl methacrylate)-copper composite

Thermal characteristics of the composites of poly(methyl methacrylate) and copper are reported, including the order of reaction and activation energy of the major second stage of pyrolysis. The randomly-distributed metal particles in the polymer matrix can form paths for heat transfer which determine the mechanism of thermal degradation.

---

Zusammenfassung Die thermischen Charakteristika der Verbindungen von Polymethylmethacrylat mit Kupfer werden zusammen mit der Reaktionsordnung und der Aktivierungsenergie der grösseren zweiten Stufe der Pyrolyse beschrieben. Die zufallsbestimmt verteilten Metallpartikel in der Polymermatrix können Wege des Wärmetransfers formen, welche den Mechanismus der thermischen Zersetzung bestimmen.

---

Résumé On décrit les caractéristiques thermiques de composites du polyméthylméthacrylate avec le cuivre, parmi lesquelles l'ordre de réaction et l'énergie d'activation de la seconde étape de la pyrolyse qui est la principale. Les particules du métal distribuées au hasard dans la matrice du polymère peuvent constituer des voies pour le transfert de chaleur qui déterminent le mécanisme de la dégradation thermique.

---

, . , .

     

Thermal oxidation of blends of poly(ethylene oxide) and poly(methyl methacrylate)

Thermal oxidation of poly(ethylene oxide) (PEO) and its blends with poly(methyl methacrylate) (PMMA) were studied using oxygen uptake measurements. The rates of oxidation and maximum oxygen uptake contents were reduced as the content of PMMA was increased in the blends. The results were indicative of a stabilizing effect by PMMA on the oxidation of PEO. The oxidation reaction at 140°C was stopped at various stages and PMMA was separated from PEO and its molecular weights were measured by gel permeation chromatography (GPC). The decrease in the number-average molecular weight of PMMA was larger as the content of PEO increased in the blends. The visual appearance of the films suggested that phase separation did not occur after thermal oxidation. The activation energy for the rates of oxidation in the blends was slightly increased compared to pure PEO. © 1992 John Wiley & Sons, Inc.     

Thermal degradation studies in poly(vinyl chloride)/poly(methyl methacrylate) blends

The miscibility, morphology, and thermal properties of poly(vinyl chloride) (PVC) blends with different concentrations of poly(methyl methacylate) (PMMA) have been studied. The interaction between the phases was studied by FTIR and by measuring the glass transition temperature (T_g) of the blends using differential scanning calorimetry. Distribution of the phases at different compositions was studied through scanning electron microscopy. The FTIR and SEM results show little interaction and gross phase separation. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of the first and second stage of degradation in PVC in the presence of PMMA were higher than the pure. The stabilization effect on PVC was found most significant with 10 wt% PMMA content in the PVC matrix. These results agree with the isothermal degradation studies using dehydrochlorination and UV-vis spectroscopic results carried out on these blends. Using multiple heating rate kinetics the activation energies of the degradation process in PVC and its blends have been reported.     

Application of ionic liquids as plasticizers for poly(methyl methacrylate)

The room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate, [C4mim][PF6] was found to be an efficient plasticizer for poly(methyl methacrylate), prepared by in situ radical polymerization in the ionic liquid medium; the polymers have physical characteristics comparable with those containing traditional plasticizers and retain greater thermal stability.     

Robust isocratic liquid chromatographic separation of functional poly(methyl methacrylate)

The separation of telechelic poly(methyl methacrylate) (PMMA) prepolymers based on the number of end-groups under critical liquid chromatography (LC) conditions has been studied using a bare-silica column, which can interact with polar functional groups. The critical solvent compositions for non-functional, mono-functional and bi-functional PMMAs were determined in normal-phase LC using mixtures of acetonitrile and dichloromethane (DCM) of varying composition as the mobile phase. The telechelic prepolymers were successfully separated according to hydroxyl (OH) functionality (with zero, one, or two OH groups, respectively) under the critical conditions, in which fast (5 min), base-line separations were obtained independent of molecular weight. Changing the column temperature, flow rate, and mobile-phase composition within a certain range did not affect the functionality separation. Therefore this isocratic LC separation method is quite robust. Evaporative light-scattering detector (ELSD) calibration curves were used for the quantitative analysis of functional PMMA prepolymers.     

Photodegradation of poly(methyl methacrylate)

The vacuum photodegradation at 30°C. of poly(methyl methacrylate) and copolymers with acrylaldehyde, methacrylaldehyde, and methyl acrylate has been studied. The polymers were examined in the form of expanded films as produced by a freeze-drying technique. At least one molecule of carbon monoxide is evolved for each chain scission. It is concluded that chain scission in poly(methyl methacrylate) is primarily the result of photoinduced aldehyde groups.     

Thermal degradation of composites of poly(methyl methacrylate) with alkoxysilane hydrolyzates

Organic-inorganic composites of poly(methyl methacrylate) with alkoxysilane hydrolyzates form transparent films. Their thermal and oxidative thermal degradation were studied by differential scanning calorimetry and thermogravimetric analysis.     

Thermal degradation of mixtures of poly(methyl methacrylate) and silver acetate

The degradation behavior of silver acetate—PMMA blends at salt/polymer ratios of 1:1, 1:5, and 1:10 has been studied by using thermal volatilization analysis (TVA) as the principal technique. Degradation of the salt has also been examined; it gives a variety of products best explained by a series of reactions resulting from an initial cleavage of CH₃COO. radicals and silver atoms. Silver acetate, when present with PMMA during degradation, results in a severe destabilization of the polymer, which breaks down to monomer at a high rate at temperatures as low as 200°C. This effect is explained by diffusion of radicals from silver acetate decomposition into the polymer phase, in which they initiate chain scission and depolymerization.     

Thermal properties of poly(methyl methacrylate) prepared by emulsifier-free emulsion polymerization

Emulsifier-free emulsion polymerization of methyl methacrylate in the presence of potassium persulfate initiator, taken in several different concentrations, at various pH values was studied with the aim to obtain colloidal crystals. The thermal properties of poly(methyl methacrylate) prepared by emulsifier-free emulsion polymerization, as the starting material for fabrication of photonic crystals, were examined in relation to the synthesis conditions.     

Branching of anionic poly(methyl methacrylate)

A viscometric determination of the degree of branching γ, of poly(methyl methacrylate) obtained by anionic polymerization proved the reaction of the growing center of poly(methyl methacrylate) with the ester group of another polymer molecule, accompanied by the formation of a trifunctional branch point. This reaction occurs if the solution polymerization of methyl methacrylate is initiated: (1) with butyllithium at ?78°C only on attaining 100% conversion and after a long time or at +20°C immediately after the polymerization has set in; (2) with lithium tert-butoxide at +20°C after a long time. The degree of branching of poly(methyl methacrylates) obtained under similar conditions in the presence of tetrahydrofuran reaches higher values than for polymers prepared in toluene. The tacticity of polymers does not affect the experimentally determined γ values.     

Electron-beam charging of poly(methyl methacrylate)

The charging of bulk poly(methyl methacrylate) by irradiation with electrons of 2 MeV energy at room temperature in vacuum was studied. The experimental data obtained using the split Faraday cup are compared with the results of numerical simulation assuming one-dimensional geometry with allowance for the spatial distribution of dose rate and injected-electron current, nonlinear properties of radiation-induced conductivity in the prebreakdown electric-field region, and the intrinsic conductivity of poly(methyl methacrylate). It was shown that published data on the electric field strength measured by means of the electro-optical Kerr effect in electron-beam charged poly(methyl methacrylate) agree satisfactorily with the calculation results.__________Translated from Khimiya Vysokikh Energii, Vol. 39, No. 3, 2005, pp. 183–189.Original Russian Text Copyright © 2005 by Sadovnichii, Tuytnev, Milekhin.     

Synthesis of poly(methyl methacrylate) macromonomer

Anionic polymerization of methyl methacrylate (MMA) was carried out in tetrahydrofuran (THF) or THF/toluene mixture at ?78°C initiated by triphenylmethyl sodium or lithium as initiators. Highly syndiotactic PMMA of low polydispersity (M _w/m _n = 1.11–1.17) could be prepared with triphenylmethyl lithium in THF or THF/toluene mixture at ? 78°C. Moreover, PMMA macromonomer having one vinylbenzyl group per polymer chain was prepared by the couplings of living PMMA initiated by triphenylmethyl lithium with p-chloromethyl styrene (CMS) at ?78°C. The coupling reaction of living PMMA initiated by triphenylmethyl sodium with CMS was scarcely occurred.     

Thermal stability of poly(methyl methacrylate) as polymerized in aqueous media by using redox systems as initiators

The thermal degradation of poly(methyl methacrylate) as polymerized in aqueous nitric acid solution using Ce(IV) alone and in combination with isobutyl alcohol, isopropyl alcohol, glucose, maltose, and cellobiose as initiator systems has been investigated using differential thermal analysis (DTA) and thermogravimetry (TGA) in dynamic nitrogen. The kinetic parameters E, n, and A have been obtained following several methods of thermogravimetric analysis. The most stable material was found to be the PMMA sample obtained with Ce(IV), and the Ce(IV)–IBA and Ce(IV)–maltose polymerized samples were the least stable. In the pyrolysis of Ce(IV)–IBA and Ce(IV)–maltose polymerized samples it was found that two reactions occurred, while in the case of the PMMA polymerized with Ce(IV), Ce(IV)–IPA, Ce(IV)–glucose, and Ce(IV)–cellobiose three reactions took place.     

Thermoluminescence of irradiated poly(methyl methacrylate)

Thermoluminescence of poly(methyl methacrylate) (PMMA) irradiated with x rays, has been studied in the temperature range 100 to 460°K. Two glow peaks with maxima at 136 and 368°K have been observed. These are analyzed by three methods and the results are compared. Both curves obey second order kinetics and correspond to activation energies of 0.17 and 0.88 eV, respectively. It is possible to identify the centers responsible for the two peaks by correlation with electron spin resonance and optical data obtained for the same samples irradiated under the same conditions. Spectral studies of the emission show that the low temperature peak has its maximum at 365 nm while the high temperature peak has its maximum at 480 nm.     

Thermal and photochemical stability of poly(methyl methacrylate) and its blends with poly(vinyl acetate)

An investigation of the thermal stability of poly(methyl methacrylate) (PMMA) blends with poly(vinyl acetate) (PVAc) revealed that PVAc acts as a stabilizer as concerns thermal and photochemical degradation when the processes take place in air. The temperatures of decomposition of these blends are higher than that of pure PMMA. The efficiency of photodegradation and photooxidation in the blends is lower than that of pure PMMA.