Properties of the Nanoscale Hydrophilic Cationic Pigment Based on Quaternary Surfactant

Dispersions of four nanoscale hydrophilic cationic pigments were prepared by micro jet milling process, in which the dodecyl trimethyl ammonium chloride (DTAC), tetradecyl trimethyl ammonium chloride (TDAC), hexadecyl trimethyl ammonium chloride (CTAC), and octadecyl trimethyl ammonium chloride (STAC) were used as the dispersers respectively. Zeta potential, particle size, viscosity and dispersion stability were tested. The effect of the hydrophobic chain of cationic quaternary surfactant on pigment dispersion's properties was discussed. The results showed that good dispersion effects were obtained when the hydrophobic chain were 14 or 16.     

Electron-beam graft-modified membranes with externally controlled flux

Pre-irradiation grafting as a means to modify commerical poly(vinylidene fluoride) (PVDF) membranes has been studied. The membranes prepared were weak cation-exchange membranes (acrylic acid functionality), anion-exchange membranes (trimethyl ammonium functionality) and temperature-sensitive membranes (N-isopropyl amide functionality). Different graft loads were obtained by varying reaction time, radiation dose and in the case of acrylic acid the graft solution composition. The trimethyl ammonium chloride functionality was obtained by grafting vinyl benzyl chloride onto a PVDF membrane and aminating the benzyl chloride groups in a 45% trimethyl amine–water solution. For a membrane grafted with 9 wt% acrylic acid the flux increased approximately 70 times when the pH was decreased from 6 to 2. For a membrane with 5 wt% trimethyl ammonium functionality the flux increased both when pH was decreased below 3 and increased above 11. For a membrane grafted with 18 wt% N-isopropyl acrylamide a sharp increase of flux was observed when the temperature was raised above 32°C.     

Effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in hydrochloric acid solution

In this study, the effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in hydrochloric acid (HCl) solution was investigated by using dodecyl trimethyl ammonium chloride (DTAC), tetradecyl trimethyl ammonium chloride (TTAC), cetyl trimethyl ammonium chloride (CTAC), and octadecyl trimethyl ammonium chloride (OTAC) as corrosion inhibitors to uncover their structure–efficiency relationships. The effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in HCl solution was studied under different conditions, such as corrosion inhibitor concentration, temperature, and acidity, and this was done using the weightlessness method. The results obtained show that these inhibitors have high corrosion inhibition effect on A₃ steel, and the corrosion inhibition efficiency is dependent on the length of the alkyl chain. At the same concentration, the longer the alkyl chain, the weaker the corrosion inhibition effect. When the temperature was 50 °C and the concentration of corrosion inhibitor was 70 mg/L, the corrosion inhibition efficiency order of the four cationic surfactants was DTAC > TTAC > CTAC > OTAC. Besides, the experimental results obtained show that the adsorption of the inhibitor on the A₃ steel surface conforms to the Langmuir type isotherm, and then the corresponding adsorption thermodynamic parameters were obtained according to these parameters. It was observed that ΔH, ΔS, and E_a increased with increase in the length of the alkyl chain. The adsorption of the inhibitor on the steel surface is an exothermic, spontaneous, entropy process.     

Dispersion copolymerization of acrylamide with quaternary ammonium cationic monomer in aqueous salts solution

Dispersion copolymerization of acrylamide (AM) with 2-methylacryloylxyethyl trimethyl ammonium chloride (DMC) has been carried out in aqueous salts solution containing ammonium sulfate and sodium chloride with poly(acryloylxyethyl trimethyl ammonium chloride) (PDAC) as the stabilizer and 2,2′-azobis[2-(2-inidazolin-2-yl)propane]-dihydro chloride (VA-044) as the initiator. A new particle formation mechanism of the dispersion polymerization for the present system has been proposed. The effects of inorganic salts and stabilizer concentration on dispersion polymerization have been investigated. The results show that varying the salt concentration could affect the morphology and molecular weight of the resultant copolymer particles significantly. With increasing the stabilizer concentration, the particle size decreased at first and then increased, meanwhile the effect on the copolymer molecular weight was the contrary. These results had been rationalized based on the proposed mechanism.     

The use of DSS as an internal standard in PMR studies of nucleic acid interactions

Two commonly used PMR internal reference compounds, 3-(trimethyl silyl) propane sulfonic acid sodium salt (DSS) and 3-(trimethyl silyl) sodium propionate (TSP), have been shown to interact with purine in aqueous solution, causing significant shifts in the resonance position of their reference protons. Tetramethyl ammonium chloride (TMACl) appears to be a more suitable reference compound for such studies.     

Effect of intercalating agents on structure and properties of dimer acid‐based polyamide modified by in situ doping of Na‐montmorillonite

Under the condition of 0.4% (mass), the effects of intercalating agents on conglomeration structure and thermal and mechanical properties of dimer acid‐based polyamide (DAPA) were investigated. The results show that layer‐stripped Na‐montmorillonite (MMT) with octadecyl trimethyl ammonium chloride caused a sharp decrease of content of the γ crystal phase in DAPA, thus bringing out decrease in mechanical properties and increase in IZOD notched impact strength while a sharp increase of content with the γ crystal phase in DAPA modified by Na‐MMT with dioctadecyl dimethyl ammonium chloride. Thus, it brought out a large increase in mechanical properties and a limited increase in IZOD notched impact strength. The decomposition reaction processes of DAPA modified by Na‐MMT and Na‐MMT with octadecyl trimethyl ammonium chloride were one step ranging from 410 to 500°C, respectively. The thermal decomposition reaction processes of DAPA modified by Na‐MMT with dioctadecyl dimethyl ammonium chloride were two steps. Copyright © 2016 John Wiley & Sons, Ltd.     

有机改性膨润土对己唑醇水悬浮体系物理稳定性的影响

利用4种季铵盐阳离子表面活性剂（十二烷基二甲基苄基氯化铵(1227)、十四烷基二甲基苄基氯化铵(1427)、十六烷基三甲基氯化铵(1631)和十八烷基三甲基氯化铵(1831)）分别对钠基膨润土（Na-Ben）进行有机改性,制得4种有机膨润土（1227-Ben、1427-Ben、1631-Ben和1831-Ben）并进行了红外光谱及X射线分析,考察了4种有机膨润土在水中的悬浮性能及对5%己唑醇水悬体系物理稳定性能的影响。 FT-IR及XRD分析结果表明,供试季铵盐阳离子的有机碳链均进入到膨润土的片层间。 水中悬浮性能测定实验表明,1831-Ben在水中悬浮性能相对较好,而其它3种均不理想,特别是1227-Ben和1427-Ben表现出强烈的斥水现象。 沉降试验表明,有机膨润土的使用有助于5%己唑醇水悬浮剂物理稳定性的提高,其中用1831-Ben制备出的水悬浮体系的物理稳定性明显优于其它3种,制剂析水率最低,屈服值与粘度最大,体系悬浮率最高,可见1831-Ben可以用作5%己唑醇水悬浮剂的抗沉降剂。     

用电活性离子对制成的离子选择电极测定阳离子表面活性剂

制备了3种基于不同电活性物质(十二烷基二甲基苄基铵-四苯硼、十六烷基三甲基铵-四苯硼、十八烷基三甲基铵-四苯硼)的阳离子表面活性剂离子选择电极,并对其性能做了测定,结果显示该类电极对阳离子表面活性剂十二烷基二甲基苄基氯化铵、十六烷基三甲基溴化铵、十八烷基三甲基氯化铵均有能斯特响应。以此类电极作为指示电极,四苯硼钠溶液作为滴定剂,对阳离子表面活性剂(十二烷基二甲基苄基氯化铵、十八烷基三甲基氯化铵、海明1622)进行了活性物含量的测定,与两相滴定法测定结果进行了比较。     

Conformational analysis of chlorocholine analogues

The high-resolution proton magnetic resonance spectra of the methylene groups of 2-chloroethyl trimethyl ammonium chloride (I) and 2-chloroethyl dimethyl ammonium chloride (II) were studied by iterative computer calculation. From the values of the spectral parameter L it is concluded that in the case of compound (I) the enthalpy difference between the antiperiplanar and the synclinal conformers is very low, probably, emphasis lies on the antiperiplanar conformation. Compound (II) exists in a dominant synclinal conformation. PCILO calculations of 2-chloroethyl trimethyl ammonium yield the antiperiplanar conformation as the most stable one in agreement with experiment. The energy difference between the antiperiplanar and the syn/anticlinal conformation is 0.7 kcal mole^?1. 2-Chloroethyl dimethyl ammonium, 2-chloroethyl methyl ammonium and 2-chloroethyl ammonium in our PCILO calculations exist in a predominant synclinal conformation. The calculated charge distributions demonstrate that the quaternary nitrogen atom is approximately neutral, the “positive” charge is distributed among the methyl groups and hydrogen atoms attached to the nitrogen atom.     

Comparison of oleyl and elaidyl isomer surfactant-counterion systems in drag reduction, rheological properties and nanostructure

Compared with quaternary ammonium cationic surfactants with saturated alkyl chains, quaternary ammonium cationic surfactants with one double-bond in their alkyl chains, when mixed with appropriate counterions (in certain molar concentration ratios, ξ), can reach much lower effective drag-reduction temperatures, while maintaining the upper drag-reduction temperature limit of the corresponding saturated drag reducing surfactant solutions. No previous study has compared the effects of cis- vs. trans-unsaturated alkyl hydrocarbon tail configurations (oleyl vs. elaidyl) trimethyl ammonium chloride cationic surfactants at different counterion/surfactant concentration ratios on micellar nanostructures, (1)H NMR spectra and on rheological and drag-reduction behavior of their solutions. Since neither pure oleyl (cis-) nor elaidyl (trans-) trimethyl ammonium chloride surfactants are commercially available, they were synthesized and their 5mM solutions with NaSal counterion at concentrations of 5mM, 7.5mM and 12.5mM were studied.     

Studies on quinones. XII. Cycloketalization of michael adducts from hydroxyquinones

The reaction of 2-hydroxy-3-(1-phenyl-3-oxobutyl)-1,4-naphthoquinone ( 1 ) with either acidic methanol or a mixture of trimethyl orthoformate, methanol and ammonium chloride resulted in the formation of the p-quinonic cycloketals: trans- and cis-4-phenyl-2-methyl-2-methoxy-3,4-dihydro-2H-naphtho[2,3-b]pyran-5,10-dione ( 2a,2b ). Cyclization of the Michael adducts 6, 10 and 11 , which are structurally related to 1 , with trimethyl orthoformate-methanol-ammonium chloride gave the corresponding p-quinonic cycloketals 7, 12 and 13 . The structures of the regioisomers 2a and 2b are proposed based on the spectral properties of compound 7 and by analysis of its proton nmr spectra.     

季铵化N,O-(2-羧乙基)壳聚糖的制备及其抑菌性能

以缩水甘油基三甲基氯化铵(GTMA)、缩水甘油基三乙基氯化铵(GTEA)、缩水甘油基三丙基氯化铵(GTPA)、缩水甘油基三丁基氯化铵(GTBA)和缩水甘油基二甲基苄基氯化铵(GDMBA)等活性季铵盐为季铵化试剂,对N,O-2-羧乙基壳聚糖(N,O-2-CEC)进行了化学改性,得到了系列季铵化N,O-2-CEC(QCEC...     

Photometric determination of quaternary ammonium compounds with hexanitrodiphenylamine. II

In strongly alkaline medium (more than 0.1 N NaOH) hexanitrodiphenylamine anion reacts with base. The reaction is rather slow and is partly reversible.Quaternary ammonium ions can be determined by extraction of their hexanitrodiphenylamine complexes with chloroform or methylene chloride at pH 11 or with methylene chloride from 3N NaOH. Only the latter method is applicable to compounds containing several quaternary ammonium groups. The compounds extracted have high molar extinction and good stability. Quaternary ammonium ions can be determined in the presence of amines, and in some cases determination of quaternary ammonium ions in admixture is possible.     

Exploring the heteroatom effect on polyelectrolyte multilayer assembly: the neglected polyoniums

Different positive polyelectrolytes having the same charge density, molecular weight, and molecular weight distribution were employed for polyelectrolyte multilayer (PEMU) assembly. The polycations differed only in the heteroatom on which the positive charge resided: poly(vinyl benzyl trimethyl ammonium) chloride, poly(vinyl benzyl trimethyl phosphonium) chloride, and poly(vinyl benzyl dimethyl sulfonium) chloride. While the ammonium repeat unit has been employed on numerous occasions for PEMU assembly, the phosphonium and sulfonium units are relatively neglected. The polyanions, poly(styrene sulfonate), PSS, or poly(acrylic acid), PAA, were typical pH-independent or pH-dependent polymers, respectively. All three polyoniums were quite similar in showing linear layer-by-layer buildup with PSS and exponential growth with PAA, under the conditions employed. Hydration and wettability were also similar between polyoniums.     

三氯化铝催化合成阳离子淀粉

以淀粉和三甲基环氧丙基氯化铵为原料,在三氯化铝催化作用下,制备了阳离子淀粉,最佳反应条件为:淀粉 50g,三甲基环氧丙基氯化铵 10g,三氯化铝 0. 74g, 50%乙醇 60mL,反应温度 50℃,反应时间 17h.     

Peculiarities of nucleophilic substitution in indolyliodonium salts

3-Indolylphenyliodonium trifluoroacetate reacts with ammonium bromide and lithium chloride and bromide to give 3-haloindoles. The reaction with ammonium chloride and tetrabutylammonium chloride leads to a mixture of 2- and 3-chloroindoles. The same mixture of chloroindoles is also formed by the action of lithium chloride but in the presence of 15-crown-5 ether. The course of the reaction is explained by ambident reaction of the cation of the iodonium salt.Deceased.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 11, pp. 1494–1496, November, 1981.     

Quaternized amino functionalized cross-linked polyacrylamide as a new solid-liquid phase transfer catalyst in reduction of carbonyl compounds with NaBH4

Poly[N-(2-aminoethyl)acrylamido]trimethyl ammonium chloride resin was developed as a new polymeric phase transfer catalyst. This quaternized polyacrylamide catalyzed the chemoselective reduction of aldehydes and ketones by NaBH₄ to give corresponding alcohols in high yields under mild conditions.     

The antibacterial finish of cotton via sols containing quaternary ammonium salts

The sols containing quaternary ammonium salts were prepared via sol-gel process. The effects of the molar rate of HCl, H₂O and EtOH to TEOS on the sol viscosity were investigated in detail. Cetyltrimethylammonium bromide (CTAB), Octadecyl dimethyl benzyl ammonium chloride (DC) and Ethylene-Bis (Octadecyl trimethyl ammonium chloride) [E-Bis(OTAC)]were added in the sols and applied to cotton samples by treated. The antibacterial activities of the samples were assessed against both Escherichia coli and Staphylococcus aureus bacteria. The samples treated by E-Bis(OTAC) sol exhibited the satisfactory antibacterial activity that resulted from the more microorganism adsorption and hydrophobicity. The antibacterial activities were still excellent after 10 times washings comparison with the control samples.     

Combined use of hydroxypropyl‐β‐cyclodextrin and ionic liquids for the simultaneous enantioseparation of four azole antifungals by CE and a study of the synergistic effect

A CE method employing a dual system of hydroxypropyl‐β‐cyclodextrin (HP‐β‐CD) and ionic liquids (ILs) has been developed for the simultaneous enantioseparation of four azole antifungals for the first time. In this study, three different types of ILs were employed as modifiers and among them dodecyl trimethyl ammonium chloride was found to be the most effective. The effects of the concentration, cations, and anions of ILs on the enantioseparation were investigated. With the developed dual system, all the enantiomers were well separated in resolutions of 3.8, 3.5, 2.8, and 2.5 for miconazole, econazole, ketoconazole, and itraconazole, respectively. The interactions between dodecyl trimethyl ammonium chloride and HP‐β‐CD were also studied using a neutral polyacrylamide coated capillary and ¹H NMR spectroscopy to further explore the synergistic effect involved. It was found that ILs improved the enantioseparation not only by changing the EOF, but also by interactions with HP‐β‐CD that could change its ability of forming inclusion complex with the enantiomers.     

基于辛可宁的几种手性季铵盐的合成及对查尔酮的催化不对称环氧化

手性相转移催化剂;合成;醚化;不对称环氧化;查尔酮