Oblique Perforation of Thick Metallic Plates by Rigid Projectiles

Oblique perforation of thick metallic plates by rigid projectiles with various nose shapes is studied in this paper. Two perforation mechanisms, i.e., the hole enlargement for a sharp projectile nose and the plugging formation for a blunt projectile nose, are considered in the proposed analytical model. It is shown that the perforation of a thick plate is dominated by several non-dimensional numbers, i.e., the impact function, the geometry function of projectile, the non-dimensional thickness of target and the impact obliquity. Explicit formulae are obtained to predict the ballistic limit, residual velocity and directional change for the oblique perforation of thick metallic plates. The proposed model is able to predict the critical condition for the occurrence of ricochet. The proposed model is validated by comparing the predictions with other existing models and independent experimental data.The English text was polished by Keren Wang     

高速碰撞下圆柱壳自由梁的穿孔特性

利用二级轻气炮加载,进行了球状2A12铝弹丸垂直撞击圆柱壳自由梁实验。并进行了弹丸速度、圆柱壳直径和壁厚等因素对穿孔直径影响的数值模拟,数值模拟结果和实验结果基本吻合。通过量纲分析和数值模拟结合,推导了穿孔直径与相关影响参数的经验关系式。研究结果表明:当圆柱壳直径和厚度不变时,高速撞击产生的穿孔直径在径向和轴向都随着弹丸速度增大而增大;当弹丸速度和圆柱壳厚度不变时,高速撞击产生的穿孔直径随着圆柱壳自由梁直径的增大而减小;当弹丸速度和圆柱壳直径不变时,穿孔直径随着圆柱壳厚度的增大而减小。     

Semi-theoretical analyses of the concrete plate perforated by a rigid projectile

Based on the three-stage perforation model, a semi-theoretical analysis is conducted for the ballistic performances of a rigid kinetic projectile impacting on concrete plates. By introducing the projectile resistance coefficients, dimensionless formulae are proposed for depth of penetration (DOP), perforation limit thickness, ballistic limit velocity, residual velocity and perforation ratio, with the projectile nosed geometries and projectile-target interfacial friction taken into account. Based on the proposed formula for DOP and lots of penetration tests data of normal and high strength concrete targets, a new expression is obtained for target strength parameter. By comparisons between the results of the proposed formulae and existing empirical formulae and large amount of projectile penetration or perforation tests data for monolithic and segmented concrete targets, the validations of the proposed formulae are verified. It is found that the projectile-target interfacial friction can be neglected in the predictions of characteristic ballistic parameters. The dimensionless DOP for low-to-mid speed impacts of non-flat nosed projectiles increases almost linearly with the impact factor by a coefficient of 2/(πS). The anti-perforation ability of the multilayered concrete plates is dependent on both the target plate thickness and the projectile impact velocity. The variation range of the perforation ratio is 1–3.5 for concrete targets.     

细长尖头刚性弹对金属靶板的斜侵彻/穿甲分析

给出细长尖头刚性弹（如尖卵、尖锥形）斜侵彻/穿甲金属靶的一个分析模型。在细长尖头弹对中厚度金属靶的斜穿甲中,韧性孔洞扩张为主要的穿甲机理;着靶初期,发生方向角的改变。研究表明,金属靶的斜穿甲仅由4个量纲一参数控制,即冲击函数I、弹体几何函数N、量纲一靶厚和撞击斜角。分析得到显式的侵彻深度、终点弹道极限、剩余速度和撞击方向改变角表达式。该模型可预期跳飞发生的临界条件。理论预期与实验结果吻合较好。     

带前舱物的钝头弹对金属靶的正穿甲分析

进一步发展了考虑结构响应的剪切冲塞模型,计及前舱物的作用,对带前舱物的钝头弹穿甲金属靶的工程问题进行了刚塑性分析,用于分析终点弹道极限和剩余速度。除剪切破坏之外,模型还考虑了靶板弯曲、膜力拉伸和前舱物撞击引起的靶板预结构响应等。给出了简洁的终点弹道性能公式,与相关实验结果较吻合。     

A constitutive-microdamage model to simulate hypervelocity projectile-target impact,material damage and fracture

A set of constitutive-microdamage equations are presented that can model shock compression and the microdamage and fracture that can evolve following hypervelocity impact. The equations are appropriate for polycrystalline metals. For impact at a projectile velocity of 6.0 km/s, numerical simulations are preformed that describe the impact of spherical soda-lime glass projectiles with aluminum 1100 rectangular target plates. Three ratios of the projectile diameter to the target thickness are chosen for the simulations, providing a wide range of damage features. The simulated impact damage is compared with experimental damage of corresponding test specimens, illustrating the capability of the model.     

A membrane model for the response of thin plates to ballistic impact

The axisymmetric response of an infinite plate to an impacting projectile is determined analytically on the hypothesis that, for large deformations, a ductile plate behaves to a good approximation like a membrane under uniform tension. The lowest projectile velocity that results in perforation (the ballistic limit), and the residual velocity after perforation, then are determined on the basis of a critical-strain failure criterion. A figure of merit that depends only on the material properties of the target and characterizes the resistance of the material to impact appears naturally in the analysis. Variations in the ballistic limit with target thickness and projectile dimensions can be determined when this figure of merit is known. The theoretical ballistic limit and residual velocity for a steel cylinder impacting a titanium plate are found to agree with available measured values. Further support for the membrane model and an estimate of its range of validity are obtained by comparing the maximum displacement of an impulsively-loaded, circular membrane with experimental data for circular plates.     

A3钢钝头弹撞击45钢板破坏模式的数值分析

不同速度范围内的A3钢钝头弹撞击45钢靶板分别表现为泰勒撞击、向日葵型花瓣帽形失效和靶板冲塞穿甲等3种不同的破坏模式,利用LS-DYNA对这种复杂的破坏机理和相应的影响因素进行了数值模拟研究。采用Johnson-Cook强度模型和累积损伤失效模型描述弹靶材料的力学性能,并考虑了塑性变形的绝热温升效应。数值模拟再现了不同破坏模式的失效过程,得到了与实验一致的结果。研究还指出,弹靶的冲塞穿甲实际是在高速撞击下,弹体发生花瓣帽形变形失效后继续穿甲靶板的后续结果。     

尖头弹穿甲韧性金属靶模型分析

基于延性扩孔模式,分析了尖头弹穿甲韧性金属靶的Chen-and-Li模型和Forrestal-and-Warren模 型。结果表明,2种模型形式相同但适用范围不同,差异源于分别应用球形和柱形动态空腔膨胀理论。将2 种模型与相关尖头弹穿甲金属靶的实验数据做了比较,对应于尖头刚性弹对韧性金属靶的延性扩孔穿甲,理 论分析与实验结果吻合。     

Effect of projectile nose shape,impact velocity and target thickness on deformation behavior of aluminum plates

The present study deals with the experimental and numerical investigations of aluminum target plates impacted by blunt, ogive and hemispherical nosed steel projectiles. The projectiles were normally impacted on the target plates of 0.5, 0.71, 1, 1.5, 2, 2.5 and 3 mm thicknesses at different velocities with the help of a pneumatic gun. Effect of projectile nose shape, impact velocity and plate thickness on the deformation of the target plates was studied. Hemispherical nosed projectile caused highest global deformation (dishing) of the target plates. Ogive nosed projectiles were found to be the most efficient penetrator for the case of plates of thicknesses 0.5, 0.71, 1.0 and 1.5 mm. For the case of plates of thicknesses 2.0, 2.5 and 3.0 mm however, blunt nosed projectiles required least energy to perforate the target plates. The ballistic limit velocity of hemispherical nosed projectiles was found to be highest as compared to the other two projectiles. Finite element analysis of the problem was carried out using ABAQUS finite element code. Results of the numerical analysis were compared with the experiments and good correlation between the two was found.     

Experimental Study on the Perforation Process of 5754-H111 and 6082-T6 Aluminium Plates Subjected to Normal Impact by Conical,Hemispherical and Blunt Projectiles

This paper presents an experimental investigation on the perforation behaviour of 5754-H111 and 6082-T6 aluminium alloys. The mechanical response of these materials has been characterized in compression with strain rates in the range of $10^{-3}~s^{-1} < \dot {\varepsilon } < 5 \cdot 10^{3}~s^{-1}$ . Moreover, penetration tests have been conducted on 5754-H111 and 6082-T6 plates of $4~mm$ thickness using conical, hemispherical and blunt projectiles. The perforation experiments covered impact velocities in the range of $50~m/s < V_{0} < 200~m/s$ . The initial and residual velocities of the projectile were measured and the ballistic limit velocity obtained for the two aluminium alloys for the different nose shapes. Failure mode and post-mortem deflection of the plates have been examined and the perforation mechanisms associated to each projectile/target configuration investigated. It has been shown that the energy absorption capacity of the impacted plates is the result of the collective role played by target material behaviour, projectile nose shape and impact velocity in the penetration mechanisms.     

有限厚块石砌体钢筋混凝土结构板抗贯穿性能的实验研究

用花岗岩和混凝土制备出了花岗岩板、钢丝网混凝土板、花岗岩与钢丝网混凝土组合板、花岗岩块石砌体钢筋混凝土结构板4种类型的有限厚靶板。采用口径为30 mm的火炮作为发射装置,利用形状相同、材料强度不同的2种弹体对上述靶板进行了侵彻贯穿实验,比较了各类靶板抗侵彻贯穿破坏现象。结果表明,设计良好的块石砌体钢筋混凝土结构板具有优良的抗贯穿性能,且其抗贯穿性能与块石粒径、块石强度、块石砌筑方式、粘结强度和钢筋混凝土结构形式密切相关。     

撞击载荷下泡沫铝夹层板的动力响应

应用泡沫金属子弹撞击加载的方式研究了固支方形夹层板和等质量实体板的动力响应,分别应用激光测速装置和位移传感器测量了泡沫子弹的撞击速度和后面板中心点的位移历史,给出了夹层板的变形与失效模式,研究了子弹冲量、面板厚度、泡沫芯层厚度及芯层密度对夹层板抗撞击性能的影响。结果表明,后面板中心点挠度最大,周边最小,整体变形为穹形,且伴有花瓣形的变形。参数研究表明,通过增加面板厚度或芯层厚度均能有效控制后面板的挠度,改善夹层板的能量吸收能力,结构响应对子弹冲量和芯层密度比较敏感。实验结果对多孔金属夹层结构的优化设计具有一定的参考价值。 更多还原     

运用极限荷载法研究钢筋混凝土板低速侵彻效应

基于不可压缩刚塑性材料模型和滑移线场理论,获得了单一容许速度场条件下刚性弹低速侵彻半无限介质的阻力函数。在此基础上,基于多速度容许场得到了刚性弹侵彻有限厚度靶的三阶段阻力曲线,并提出了震塌与贯穿的临界条件,通过与实验结果、UMIST公式及古比雪夫的对比,验证了本文方法在钢筋混凝土板低速撞击问题中的适用性,分析了弹头形状、冲击因子和钢筋阻力系数等参数对临界震塌(贯穿)厚度的影响。     

Penetration force measurement of thin plates by laser doppler anemometry

An experimental method is developed by applying laser-Doppler anemometry (LDA) to measure the velocity history of a projectile impact on a target. The force history was obtained by assuming the projectile to be rigid and by differentiating a polynomial which best fitted the obtained velocity data. This method was then applied to the impact of a hemispherically tipped striker on 1-mm thick aluminum plates. The initial velocity of the projectile ranged from several m/s to 93.5 m/s. When these velocities were low enough not to produce cracks on the plate, double-force peaks were observed in each test, and the value corresponding to the higher peak was proportional to the initial velocity of the projectile. Further, this peak force occurred when the projectile just started to rebound, and spring-back behavior of the plate always occurred. Once the cracks on the target started to form, the peak impact force dropped, and the double-peak phenomenon disappeared. It was also found that the peak force was at approximately the same level for impact speeds above the ballistic limit of the plate. On the other hand, a power law was found to perfectly fit the relationship between the absorbed kinetic energy and the initial velocity of the projectile when it was lower than the ballistic limit.     

Perforation of steel and polycarbonate plates by tumbling projectiles

An experimental investigation to assess the effect of tumbling by hard-steel, blunt-faced cylindrical projectiles on the impact response of thin 4130 steel and polycarbonate target plates was performed. Deformation and failure phenomena were observed and discussed; comparisons of the results with analytical models and numerical stimulation, described in a previous paper, were also performed for the steel targets. The final velocity of the projectile and the crater length in the target were correlated with the striker impact angle (or yaw angle with a zero oblique angle); reasonable agreement was attained among the experimental, analytical and numerical results. It was found that an increase of the impact angle can increase the velocity drop and the crater length markedly. The increase tends to be stabilized after the impact angle exceeds 50° and the consequences in such a case are almost the same as in side-on impact.     

高速3D-DIC测试技术在装甲钢贯穿试验中的应用

数字图像相关（digital image correlation, DIC）技术作为一种非接触、非干涉的全场无损光学量测技术,可获取材料表面的动态变形信息和破坏过程。为了评估装甲钢的抗弹性能并探索高速三维数字图像相关（3D-DIC）技术在钢板贯穿试验测试中的应用,基于氢氧爆轰驱动弹道枪开展了7发15 mm口径可变形弹体以不同速度（255～568 m/s）冲击不同厚度（5、8和10 mm）高强高硬装甲钢板的试验,并结合帧率为144 000 s?1的高速3D-DIC测试技术获取了靶板的离面位移和应变时程。随后,基于前期标定并验证的装甲钢本构模型参数,对上述试验进行了数值模拟。通过对比弹体残余速度和长度验证了有限元分析方法的可靠性。进一步通过对比试验与数值模拟得到的靶背离面位移时程曲线和不同时刻靶背的应变云图,验证了高速3D-DIC测试结果的准确性。最后,对比分析了靶板最大离面位移与弹体冲击速度和装甲钢板厚度的关系。高速3D-DIC测试技术的应用可为相关试验测试提供参考,靶板最大离面位移分析结果可为屏障类防护结构的分析验证和优化设计提供试验依据。     

93W杆式弹超高速撞击多层Q345钢靶毁伤及微观分析

为了解杆式弹超高速撞击多层薄钢靶的破坏过程及毁伤机理,开展了克级93W杆式弹正撞击多层Q345钢靶实验及数值模拟研究,通过扫描电子显微镜（scanning electron microscope,SEM）及金相显微镜,分析了超高速撞击实验后靶板材料的微观组织及成分。结果表明,超高速撞击作用下,靶板呈现出“翻唇”穿孔变形、花瓣状塑性变形、撕裂、撞击成坑及鼓包等破坏模式。靶板前3层毁伤以超高速穿孔为主,孔洞数目多但面积小,后几层靶板毁伤孔洞数目少且孔径呈先增大后减小趋势。微观分析表明靶材在强冲击压力下发生晶粒碎化、熔化及再结晶,撞击过程中会形成微孔聚集与微裂纹,可见靶板失效主要是熔融混合物冷却过程中产生的热应力与切应力下的剪切撕裂综合作用的结果。     

Rigorous model-based uncertainty quantification with application to terminal ballistics—Part II. Systems with uncontrollable inputs and large scatter

This Part II of this series is concerned with establishing the feasibility of an extended data-on-demand (XDoD) uncertainty quantification (UQ) protocol based on concentration-of-measure inequalities and martingale theory. Specific aims are to establish the feasibility of the protocol and its basic properties, including the tightness of the predictions afforded by the protocol. The assessment is based on an application to terminal ballistics and a specific system configuration consisting of 6061-T6 aluminum plates struck by spherical 440c stainless steel projectiles at ballistic impact speeds in the range of 2.4–2.8 km/s. The system's inputs are the plate thickness, plate obliquity and impact velocity. The perforation area is chosen as the sole performance measure of the system. The objective of the UQ analysis is to certify the lethality of the projectile, i.e., that the projectile perforates the plate with high probability over a prespecified range of impact velocities, plate thicknesses and plate obliquities. All tests were conducted at Caltech's Small Particle Hypervelocity Range (SPHIR), which houses a two-stage gas gun. A feature of this facility is that the impact velocity, while amenable to precise measurement, cannot be controlled precisely but varies randomly according to a known probability density function. In addition, due to a competition between petalling and plugging mechanisms for the material system under consideration, the measured perforation area exhibits considerable scatter. The analysis establishes the feasibility of the XDoD UQ protocol as a rigorous yet practical approach for model-based certification of complex systems characterized by uncontrollable inputs and noisy experimental data.