Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Novel blends from agave fibers and poly(methyl methacrylate)

Cellulose-rich fibers were isolated from Agave lechuguilla (AL) and Agave fourcroydes (AF) growing in the Mexican northeast. These fibers are a valuable feedstock for the preparation of blends with synthetic polymers like poly(methyl methacrylate), PMMA. Blends of different types of agave fibers (dewaxed, mercerized, and grafted) and PMMA were prepared and investigated by means of tension measurements and dynamic mechanical analysis. The fiber-containing blends are more stable than the plain PMMA. Surprisingly, the mechanical stability of the blends is practically independent of the pretreatment of the fibers. Methyl methacrylate (MMA) was grafted onto the biopolymer fibers initiated by the cerammonium nitrate redox initiator. Grafting yields of 26.5% were realized with fibers from AL while up to 75.8% MMA was grafted onto fibers from AF. The materials were characterized by means of FTIR spectroscopy and DSC.     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

Thermal oxidation of blends of poly(ethylene oxide) and poly(methyl methacrylate)

Thermal oxidation of poly(ethylene oxide) (PEO) and its blends with poly(methyl methacrylate) (PMMA) were studied using oxygen uptake measurements. The rates of oxidation and maximum oxygen uptake contents were reduced as the content of PMMA was increased in the blends. The results were indicative of a stabilizing effect by PMMA on the oxidation of PEO. The oxidation reaction at 140°C was stopped at various stages and PMMA was separated from PEO and its molecular weights were measured by gel permeation chromatography (GPC). The decrease in the number-average molecular weight of PMMA was larger as the content of PEO increased in the blends. The visual appearance of the films suggested that phase separation did not occur after thermal oxidation. The activation energy for the rates of oxidation in the blends was slightly increased compared to pure PEO. © 1992 John Wiley & Sons, Inc.     

Influence of clay on the morphology and phase separation behavior of poly(methyl methacrylate)/poly(styrene-co-acrylonitrile) blends

The effect of clay on the morphology and phase-separation behavior of poly(methyl methacrylate)/poly(styreneco-acrylonitrile)(PMMA/SAN) blends and the variation of clay dispersion have been investigated. With the evolution of phase separation in PMMA/SAN, most of the clays are first located at the boundaries between PMMA and SAN, and then gradually move to the PMMA-rich domain, owing to the affinity of clay to PMMA. The introduction of clay causes the increase of binodal and spinodal temperatures of PMMA/SAN and enlarges their metastable region, indicating the phase stabilizing effect of clay on the matrix. But the influence of clay on the cloud points obviously depends on the composition of PMMA/SAN. The selective adsorption of PMMA on the clay results in the difference between the composition of surface layer and that of polymer matrix. Hence, the clay plays the role of an agent changing the conditions of phase structure formation.     

Polyepichlorohydrin polyurethane/poly(methyl methacrylate) interpenetrating polymer networks

Polyurethane (PU) based on polyepichlorohydrin/poly(methyl methacrylate) (PECH/PMMA) interpenetrating polymer networks (IPNs) was synthesized by a simultaneous method. The effects of composition, hydroxyl group number of PECH, NCO/OH ratio and crosslinking agent content in IPNs were investigated in detail. Some other glycols, such as poly(ethylene glycol), poly(propylene glycol) and hydroxyl-terminated polybutadiene, were also used to obtain PU/PMMA IPNs. The interpenetrating and fracture behaviors of the IPNs are explained briefly.     

Compatibility in poly(ethylene oxide)–poly(methyl methacrylate) blends

The compatibility of poly(ethylene oxide)-poly(methyl methacrylate) (PEO-PMMA) blends were examined covering the complete composition range. Up to 20% of PEO content films were transparent and glass transition temperatures were determined by DSC and by refractive index vs. temperature measurements. Only one T_g was obtained for these samples and the relationship between T_g and composition has been evaluated. At higher PEO content crystallization took place and the films were opaque. Melting temperatuures of PEO in blends were determined by DSC. Melting point depression was observed for increasing proportion of PMMA and the binary interaction parameter has been calculated.     

Thermal degradation studies in poly(vinyl chloride)/poly(methyl methacrylate) blends

The miscibility, morphology, and thermal properties of poly(vinyl chloride) (PVC) blends with different concentrations of poly(methyl methacylate) (PMMA) have been studied. The interaction between the phases was studied by FTIR and by measuring the glass transition temperature (T_g) of the blends using differential scanning calorimetry. Distribution of the phases at different compositions was studied through scanning electron microscopy. The FTIR and SEM results show little interaction and gross phase separation. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of the first and second stage of degradation in PVC in the presence of PMMA were higher than the pure. The stabilization effect on PVC was found most significant with 10 wt% PMMA content in the PVC matrix. These results agree with the isothermal degradation studies using dehydrochlorination and UV-vis spectroscopic results carried out on these blends. Using multiple heating rate kinetics the activation energies of the degradation process in PVC and its blends have been reported.     

Thermogravimetric studies on poly(methyl methacrylate), poly(tetrahydrofuran) and their blends

TG studies are given for PMMA prepared by radical polymerization, PTHF prepared by cationic polymerization, and their blends. A procedure is proposed for determining the activation energy, frequency factor, and the order of events corresponding to the respective stages of the multistage TG curves. The order of the initial event of PMMA is not the 1st. It is shown for this discussion that the relationship between mass loss and time of the 2nd order reaction is similar to that of the depolymerization including the vaporization process at the earlier times. Some of TG curves of PTHF are not dependent on the heating rate. This independence depends on the size of sample. The order of event of PTHF, which is obtained from TG curves dependent on the heating rate, is the 0th. The event order equal to the 0th reflects major contribution of vaporization in the event. The TG behaviors shown by the procedure mentioned above for the PMMA/PTHF blends with the smaller PMMA or PTHF contents cancel those of PMMA or PTHF. This revised version was published online in July 2006 with corrections to the Cover Date.     

Features of the in situ formation of a linear poly(methyl methacrylate)-crosslinked polyurethane blend in the presence of an oligomeric initiator

The process of the in situ formation of a linear poly(methyl methacrylate)-crosslinked polyurethane blend in the presence of different amounts of an oligomeric azo initiator containing fragments of a polyurethane chain and groups capable of initiating the radical polymerization of methyl methacrylate has been studied. It has been shown that the use of an azo initiator providing for the formation of block copolymers retards the phase separation in the system and favors the formation of a finer blend structure that is characteristic by a domain size several times smaller than that of the pristine blend, without the azo initiator. The optimum azo initiator concentration that results in a better dispersion of polyurethane in poly(methyl methacrylate) has been determined.     

Morphological studies of poly(vinylidene fluoride) and its blends with poly(methyl methacrylate)

Both pure poly(vinylidene fluoride) (PVF₂) and its blends with poly(methyl methacrylate) (PMMA) develop a variety of morphologies when they are crystallized above the 420–424 K range. Two populations of spherulites as well as axialitelike growths are observed. Addition of the PMMA lowers the temperature where these new morphologies develop, makes the spherulites more open, causes the banding periodicity to decrease, and increases the number of small, coarse spherulites. These structures melt in three regimes. The highest-melting-point crystals arise only from a solid-solid transformation of the lowest-melting-point ones. This solid-state transition sometimes causes mixed spherulites to be formed in the blends. Electron and wide-angle x-ray diffraction show the lowest-melting-point species to be α crystals, while the other two are γ crystals. The highest-melting-point species, labeled γ′, and the α crystals seem to be more ordered than the other γ crystals.     

Melting studies of poly(vinylidene fluoride) and its blends with poly(methyl methacrylate)

Blends of poly(vinylidene fluoride) (PVF₂) and poly(methyl methacrylate) exhibit complex melting behavior when crystallized at low undercoolings. Three crystals comprised of two different PVF₂ forms grow. Hoffman-Weeks plots of the observed melting points T_m of these crystals versus crystallization temperatures are constructed. The lowest-melting-point species, the α form, shows a change in slope which is attributed to fewer head-to-head PVF₂ units trapped in the crystal at higher temperatures. Defect energies in the crystal due to these units are calculated to be from 6.3 to 10.3 kJ/mol. Estimating lamellar thicknesses from the slopes of the two regions gives much more reasonable values when the high-temperature data are used. Removal of kinetic effects that lower the observed T_m by extrapolating the data to obtain T permits the thermodynamic interaction energy density B between the two polymers to be obtained. The low-temperature α-form data give B = ?8.83 × 10⁶ J/m³. The high-temperature α-form data and the T of the γ-form crystals both show B to vary from ?5.40 × 10⁶ to ?2.96 × 10⁷ J/m³ as the blend composition goes from 40.1 vol % to pure PVF₂.     

Effects of organoclays on morphology and thermal and rheological properties of polystyrene and poly(methyl methacrylate) blends

Morphology, thermal and rheological properties of polymer‐organoclay composites prepared by melt‐blending of polystyrene (PS), poly(methyl methacrylate) (PMMA), and PS/PMMA blends with Cloisite® organoclays were examined by transmission electron microscopy, small‐angle X‐ray scattering, secondary ion mass spectroscopy, differential scanning calorimetry, and rheological techniques. Organoclay particles were finely dispersed and predominantly delaminated in PMMA‐clay composites, whereas organoclays formed micrometer‐sized aggregates in PS‐clay composites. In PS/PMMA blends, the majority of clay particles was concentrated in the PMMA phase and in the interfacial region between PS and PMMA. Although incompatible PS/PMMA blends remained phase‐separated after being melt‐blended with organoclays, the addition of organoclays resulted in a drastic reduction in the average microdomain sizes (from 1–1.5 μm to ca. 300–500 nm), indicating that organoclays partially compatibilized the immiscible PS/PMMA blends. The effect of surfactant (di‐methyl di‐octadecyl‐ammonia chloride), used in the preparation of organoclays, on the PS/PMMA miscibility was also investigated. The free surfactant was more compatible with PMMA than with PS; the surfactant was concentrated in PMMA and in the interfacial region of the blends. The microdomain size reduction resulting from the addition of organoclays was definitely more significant than that caused by adding the same amount of free surfactant without clay. The effect of organoclays on the rheological properties was insignificant in all tested systems, suggesting weak interactions between the clay particles and the polymer matrix. In the PS system, PMMA, and organoclay the extent of clay exfoliation and the resultant properties are controlled by the compatibility between the polymer matrix and the surfactant rather than by interactions between the polymer and the clay surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 44–54, 2003     

Rheology and phase separation in polystyrene/poly(vinyl methyl ether) blends

Blends of monodisperse polystyrene and poly(vinyl-methyl-ether) of various compositions were prepared from solution in benzene. Dynamic rheological properties of these blends were studied at different temperatures below, near, and above T_s, the temperature of phase separation, and in a frequency range from 0.05 to 100 rad/s. A flattening in the storage modulus and an initial plateau for the complex viscosity were observed near and above T_s in the low-frequency region; in contrast, below T_s the behavior of the blends was similar to that of the homopolymers. The WLF superposition principle applies only at temperatures below T_s, i.e., in the miscible and homogeneous region. G″ versus G′ representations for the blends were found to be independent of temperature and to vary with composition in the miscible region but are temperature and composition-dependent in the immiscible region. It is also shown that the η″ versus η′ representation is a useful tool for characterizing phase separation of blends and is more sensitive than the classical frequency dependence of the material functions.     

Phase separation studies on poly(vinylidene fluoride) and poly(methyl methacrylate) quenched blends

A combined study by SAXS and DSC on quenched blends of PVDF and PMMA is presented. Attention is focused on the first stage of the phase separation process during annealing that is shown to be mainly determined by the diffusion of the PVDF molecules from the amorphous blend phase towards the crystals growth front. The experimental monomer diffusion constants at T > T_g are compared with those expected theoretically using the approximation of the fast model process and the WLF equation for the relaxation frequency of the monomer. The nature and composition of the crystal interphase are discussed in terms of the SAXS invariant for the whole system and the calorimetric data derived from the T_g transitions observed.     

Surface and interface morphology of polystyrene/poly(methyl methacrylate) thin‐film blends and bilayers

The surface and interface morphologies of polystyrene (PS)/poly(methyl methacrylate) (PMMA) thin‐film blends and bilayers were investigated by means of atomic force microscopy (AFM) and X‐ray photoelectron spectroscopy. Spin‐coating a drop of a PS solution directly onto a PMMA bottom layer from a common solvent for both polymers yielded lateral domains that exhibited a well‐defined topographical structure. Two common solvents were used in this study. The structure of the films changed progressively as the concentration of the PS solution was varied. The formation of the blend morphology could be explained by the difference in the solubility of the two polymers in the solvent and the dewetting of PS‐rich domains from the PMMA‐rich phase. Films of the PS/PMMA blend and bilayer were annealed at temperatures above their glass‐transition temperatures for up to 70 h. All samples investigated with AFM were covered with PS droplets of various size distributions. Moreover, we investigated the evolution of the annealed PS/PMMA thin‐film blend and bilayer and gave a proper explanation for the formation of a relatively complicated interface inside a larger PS droplet. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 9–21, 2006     

Melting point depression in poly (ethylene oxide)-poly (methyl methacrylate) blends

Thermo-optical analysis of solution cast mixtures of poly (ethylene oxide) (POE) and poly (methyl methacrylate) (PMMA) has been carried out. Melting point depression was observed for increasing proportion of PMMA in the mixture. An analytical expression appropriate to the crystallineamorphous polymer pair has been applied to explain the melting point depression in terms of thermodynamic quantities. From this expression, the interaction parameter for the mixture has been evaluated. The influence of $\text{M}$_w of POE on the binary interaction parameter has been studied.     

Uniaxial drawing of poly(ethyleneoxide)/poly(methyl methacrylate) blends by solid-state extrusion

Ultradrawn ribbons of solution-cast blends of poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) have been prepared by a solid-state coextrusion in a capillary rheometer. An increase of noncrystallizable PMMA in the blends drastically decreased the drawability from a draw ratio of 36 for pure PEO to 5 for a mixture of PEO/PMMA 40/60% by weight. A low crystallinity and depression of melting temperature for PEO were observed with increasing draw. The Flory-Huggins theory for melting temperature depression has been used to derive the binary interaction parameter for these blends.     

Thermo-oxidative dehydrochlorination of rigid and plasticised poly(vinyl chloride)/poly(methyl methacrylate) blends

The aim of this work was to study the thermo-oxidative dehydrochlorination of rigid and plasticised poly(vinyl chloride)/poly(methyl methacrylate) blends. For that purpose, blends of variable compositions from 0 to 100 wt% were prepared in the presence (15, 30 and 50 wt%) and in the absence of diethyl-2-hexyl phthalate as plasticiser. Their miscibility was investigated by using differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). Their thermo-oxidative degradation at 180 ± 1 °C was studied and the amount of HCl released from PVC was measured by a continuous potentiometric method. Degraded samples were characterised, after purification, by FTIR spectroscopy and UV-visible spectroscopy. The results showed that the two polymers are miscible up to 60 wt% of poly(methyl methacrylate) (PMMA). This miscibility is due to a specific interaction of hydrogen bonding type between carbonyl groups (CO) of PMMA and hydrogen (CHCl) groups of PVC as shown by FTIR analysis. On the other hand, PMMA exerted a stabilizing effect on the thermal degradation of PVC by reducing the zip dehydrochlorination, leading to the formation of shorter polyenes.     

Fracture behavior of amorphous and semicrystalline blends of poly(vinylidene fluoride) and poly(methyl methacrylate)

The fracture behavior of blends of poly(vinylidene fluoride) and poly(methyl methacrylate) was investigated all over the composition range. A detailed analysis of the net stress versus crack opening displacement curves was performed. Fracture surface observations allowed statements on the process zone characteristics ahead of the crack tip. For the amorphous blends, the crack initiation energy is well related to the glass transition temperature. For the semicrystalline blends, the fracture energy is correlated with the degree of crystallinity. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012