Development of a sample preparation procedure of sewage sludge samples for the determination of polycyclic aromatic hydrocarbons based on selective pressurized liquid extraction

An automated, simple and sensitive method based on selective pressurized liquid extraction (SPLE) was developed for the analysis of polycyclic aromatic hydrocarbons in sewage sludge samples. The new sample preparation procedure consists of on-line clean-up by inclusion of sorbents in the extraction cell, and combines elevated temperatures and pressures with liquid solvents to achieve fast and efficient removal of target analytes from complex sewage sludge matrices. The effects of various operational parameters (e.g. sample pretreatment, extraction solvent, temperature, pressure, static time, etc.) on the performance of SPLE procedure were carefully investigated, obtaining the best results when SPLE conditions were fixed at 140 °C, 1500 psi, static time of 5 min and n-hexane as extraction solvent. A new programmed temperature vaporization–gas chromatography–tandem mass spectrometry method based on large volume injection (PTV–LVI–GC–MS/MS) was also developed and analytical determinations were performed by high performance liquid chromatography coupled with fluorescence detection and GC–MS/MS. The extraction yields for the different compounds obtained by SPLE ranged from 84.8% to 106.6%. Quantification limits obtained for all of these studied compounds (between 0.0001 and 0.005 μg g⁻¹, dry mass) were well below the regulatory limits for all compounds considered. To test the accuracy of the SPLE technique, the optimized methodology was applied to the analysis of a certified reference material (sewage sludge (BCR088)) and a reference material (sewage sludge (RTC-CNS312-04)), with excellent results.     

Determination of bisphenol A in sewage effluent and sludge by solid-phase and supercritical fluid extraction and gas chromatography/mass spectrometry

Methods have been developed for the determination of bisphenol A (BPA) residues in municipal sewage and sludge samples. BPA in wastewater samples was enriched with a C18 solid-phase extraction cartridge, eluted with acetone, and converted to the pentafluoropropionyl derivative. For sludge samples, BPA was acetylated and extracted with supercritical carbon dioxide. In both cases, BPA-d16 was used as a surrogate to monitor extraction efficiency. Final analyses of derivatized sample extracts were performed by gas chromatography/mass spectrometry operating in the electron impact mode. For water samples, mean recoveries and standard deviations were 89 +/- 6, 94 +/- 4, and 85 +/- 7% at fortification levels of 1, 0.1, and 0.025 microg/L, respectively, with a method detection limit of 0.006 microg/L. For solid waste samples, mean recoveries and standard deviations were 93 +/- 5 and 92 +/- 6% at fortification levels of 2.5 and 0.25 microg/g, respectively, and the method detection limit was 0.05 microg/g. For the Canadian samples under investigation, concentrations of BPA ranged from 49.9 to 0.031 microg/L in sewage influent and effluent, and from 36.7 to 0.104 microg/g in sludge.     

Focused ultrasound solid–liquid extraction and gas chromatography tandem mass spectrometry determination of brominated flame retardants in indoor dust

This study presents a focused ultrasound solid-liquid extraction (FUSLE) and gas chromatography tandem mass spectrometry method for the determination of brominated diphenyl ethers (BDEs), from mono- to hexa-congeners, in indoor dust. This approach provided a simple, fast, and economical method. After the solvent extraction selection, the FUSLE conditions were studied using a central composite design. Finally, the number of extraction cycles was studied. The selected conditions were 8?mL of 3:1 n-hexane-acetone mixture as extraction solvent, at a power of 65% for 20?s. The proposed method allowed accurate determination of BDEs, with recovery values around 100% and detection limits between 0.05 and 0.8?ng?g(-1). It also has advantages over other existing methods in terms of simplicity, analysis time, and solvent consumption. The analysis of several indoor dust samples showed high concentration values of BDEs 47, 99, 100, 153, and 154 in some of the samples, moreover, BDEs 47 and 99 were found in all samples.     

Selective pressurized liquid extraction of estrogenic compounds in soil and analysis by gas chromatography-mass spectrometry

A selective pressurized liquid extraction (SPLE) method, followed by gas chromatography–mass spectrometry (GC–MS), for the simultaneous extraction and clean-up of estrone (E1), 17β-estradiol (E2), 17α-ethynylestradiol (EE2), estriol (E3) and bisphenol A (BPA) from soil samples is described. The on-line clean-up of soil by SPLE was achieved using different organic matter retainers, including silica, alumina and Florisil, the most effective being silica. Thus, different amounts of silica, in conjunction with different extraction solvents (acetone, ethyl acetate, isohexane and dichloromethane), either alone or in combination, were used to extract the target chemicals from spiked soil samples. It was shown that 3 g silica resulted in satisfactory rates of recovery of target compounds and acetone:dichloromethane (1:3, v/v) was efficient in extracting and eluting estrogenic compounds for SPLE. Variables affecting the SPLE efficiency, including temperature and pressure were studied; the optimum parameters were 60 °C and 1500 psi, respectively. The limits of detection (LODs) of the proposed method were 0.02–0.37 ng g⁻¹ for the different estrogenic chemicals studied. The outputs using the proposed method were linear over the range from 0.1 to 120 ng g⁻¹ for E1, E2, EE2, 0.2–120 ng g⁻¹ for E3, and 0.5–120 ng g⁻¹ for BPA. The optimized method was further verified by performing spiking experiments in natural soil matrices; good rates of recovery and reproducibility were achieved for all selected compounds and the method was successfully applied to soil samples from Northeast Scotland, for the determination of the target compounds.     

Determination of UV filters in packaging by focused ultrasonic solid-liquid extraction and liquid chromatography

A focused ultrasonic solid-liquid extraction (FUSLE) and high performance liquid chromatography (HPLC) with a diode array detector (DAD) is proposed for the determination of ten fat-soluble UV filters in packaging. FUSLE technique is relatively new and has been used for the extraction of a few analytes; such as polycyclic aromatic hydrocarbons and other organic pollutants. In this work, it has been demonstrated that FUSLE is a useful, fast and simple extraction methodology for UV filters because the complete extraction was carried out with just 6ml of tetrahydrofuran and in only one cycle of 30s. The developed method has been validated and applied to the analysis of polyethylene-based multilayer packaging samples. The FUSLE-based method allows the sensitive detection of most of the UV-filters in polyethylene, with limits of detection between 0.4 and 8.5ngmg(-1) (except for BDM). Intra and inter-day relative standard deviation values were below 5 and 14%, respectively, except for MBP. In addition, the proposed method was more efficient than tetrahydrofuran extraction under reflux for 2.5h for all the analytes except for EMT and BDM. Therefore, the developed method can be used to establish the absorption capability of different types of packaging and this information will be very useful in packaging selection.     

Determination of bisphenol A and 4-nonylphenol in human milk using alkaline digestion and cleanup by solid-phase extraction.

A highly sensitive and selective method based on alkaline digestion for the simultaneous determination of bisphenol A (BPA) and 4-nonylphenol (NP) was developed. The method consists of digestion of the matrix with ethanolic KOH, extraction with diethyl ether under a mild alkaline condition, cleaning with successive aminopropyl (NH2) cartridges and derivatization followed by a GC-MS analysis. The assay accuracies, expressed as recoveries, were 82 - 113% for BPA and 89 - 97% for NP. The limits of detection of BPA and NP were 0.09 ng/g and 0.50 ng/g, respectively. The procedure will be reliable for the trace analysis of BPA and NP in human milk, since alkaline digestion can diminish their documented association with protein.     

A new sample preparation method for determination of acidic drugs in sewage sludge applying microwave assisted solvent extraction followed by gas chromatography-mass spectrometry

This paper presents a new sample preparation procedure for determination of selected acidic pharmaceuticals (ibuprofen, naproxen, ketoprofen, and diclofenac) in sewage sludge using microwave assisted solvent extraction, dispersive matrix extraction (DME) followed by the conventionally applied solid phase extraction (SPE), derivatization, and gas chromatography-mass spectrometry. The recoveries calculated from analytical data of spiked sludge samples changed in the range of 80-105% ± 15% for the four pharmaceuticals in mixed and activated sludge depending on the efficiency of the clean-up procedure. The measured concentration values of ibuprofen and naproxen were identical in the mixed and the activated sludge samples. However, ketoprofen and diclofenac showed about twice as high concentration in activated sludge than in the mixed one independently of the applied extraction method. The typical concentration ranges of ibuprofen, naproxen, ketoprofen and diclofenac in sewage sludge were 10-30 ng/g, 30-50 ng/g, 50-130 ng/g, and 50-140 ng/g respectively.     

Simultaneous extraction of several persistent organic pollutants in sediment using focused ultrasonic solid-liquid extraction

Focused ultrasonic solid-liquid extraction (FUSLE) has been optimised for simultaneous analysis of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), phthalate esters (PEs), and nonylphenols (NPs) in sediment samples. Optimisation was performed using naturally polluted freeze-dried sediment samples. The variables studied during the optimisation process were: percentage of maximum power (10-60%), extraction time (10-300 s), number of cycles (1-9), composition of the extraction solvent (acetone-n-hexane, 10:90-90:10), and sample mass (0.1-1 g). The volume of the extractant was constant (10 mL) and the extraction was performed at 0 degrees C in an ice-bath during the optimisation process. All these variables were studied using an experimental design approach by means of The Unscrambler software. The extraction time and the operational variables (number of cycles and power) had no statistically significant effect in the extraction and they were held at 2 min, 20% power, and seven cycles, respectively. The mass and the addition of non-polar solvent (n-hexane) had a negative effect in the extraction yield and, thus, the mass was held at 0.5 g and pure acetone was used as extraction solvent. After those variables were optimised, the effect of the extraction temperature (0 degrees C or room temperature) was also studied. The validation of the extraction method was performed using NIST-1944 reference material in the case of PAHs and PCBs. Because no certified reference sediment is available for PEs and NPs, the results obtained for FUSLE were compared with those obtained for microwave-assisted extraction (MAE) under conditions optimised elsewhere. In all the cases the analysis were performed by gas chromatography-mass spectrometry (GC-MS). Good accuracy were achieved in all cases. The limits of detection (LODs) obtained were between 0.10 and 1.70 ng g(-1) for PAHs (except for naphthalene 5.33 ng g(-1)), 0.02 and 0.16 ng g(-1) for PCBs, 46 and 188 ng g(-1) for PEs, and 0.6 and 12.4 microg g(-1) for NPs. The precision was around 5-10% for most of the PAHs and PCBs and around 2-10% for most of the PEs and NPs.     

Determination of musk fragrances in sewage sludge by pressurized liquid extraction coupled to automated ionic liquid‐based headspace single‐drop microextraction followed by GC‐MS/MS

A method for the quantitative determination of ten musk fragrances extensively used in personal care products from sewage sludge was developed by using a pressurized liquid extraction (PLE) followed by an automated ionic liquid‐based headspace single‐drop microextraction and gas chromatography‐tandem mass spectrometry. The influence of main factors on the efficiency of PLE was studied. For all musks, the highest recovery values were achieved using 1 g of pretreated sewage sludge, H₂O/methanol (1:1) as an extraction solvent, a temperature of 80°C, a pressure of 1500 psi, an extraction time of 5 min, 2 cycles, a 100% flush volume, a purge time of 120 s, and 1 g Florisil as in‐cell clean‐up extraction sorbent. The use and optimization of an in‐cell clean‐up sorbent was necessary to remove fatty interferents of the PLE extract that make the subsequent ionic liquid‐based headspace single‐drop microextraction difficult. Validation parameters, namely LODs and LOQs, ranged from 0.5–1.5 to 2.5–5 ng/g, respectively. Good levels of intra‐ and interday repeatabilities were obtained analyzing sewage sludge samples spiked at 10 ng/g (n = 3, RSDs < 10%). The method applicability was tested with sewage sludge from different wastewater treatment plants. The analysis revealed the presence of all the polycyclic musks studied at concentrations higher than the LOQs, ranging from 6 to 530 ng/g. However, the nitro musk concentrations were below the LOQs or, in the case of musk xylene, was not detected.     

Selective extraction of sulfonamides, macrolides and other pharmaceuticals from sewage sludge by pressurized liquid extraction

A method for the quantitative determination of three macrolides, five sulfonamides, ranitidine, omeprazole and trimethoprim in sewage sludge samples was developed by using pressurized liquid extraction and high-performance liquid chromatography-electrospray ionization mass spectrometry. The extraction solvent and such operational parameters as temperature, pressure, extraction time and purge time were optimized in pressurized liquid extraction. The experimental conditions were: an extraction solvent of water (pH 3):methanol (1:1, v/v), a temperature of 80 degrees C, a pressure of 1500 psi, a sample weight of 5 g, an extraction time of 5 min, one cycle, a flush volume of 60% and a purge time of 120 s. All recoveries were over 74%, except those for ranitidine whose value was 54%. The repeatability and reproducibility between days expressed as relative standard deviation (n = 3) were lower than 11% and 15%, respectively. The limit of detection values ranged from 2 to 11 microg/kg dry weight (d.w.). The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants. Roxithromycin and tylosin were determined in the samples and tylosin showed the highest value (4.0 mg/kg d.w.).     

Simultaneous determination of fluoroquinolones,sulfonamides and tetracyclines in sewage sludge by pressurized liquid extraction and liquid chromatography electrospray ionization-mass spectrometry

A new scheme for the quantitative determination of traces of fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) in sewage sludge was developed. The compounds were simultaneously extracted from sewage sludge by pressurized liquid extraction (PLE). A novel and effective method for PLE was developed. Solid-phase extraction was used for cleaning up the extracts. Identification and quantification of the compounds was done using high-performance liquid chromatography with electrospray ionization mass spectrometry in selected reaction monitoring mode. The best recovery of FQs and TCs was obtained by using hydrophilic–lipophilic balance cartridges, recoveries ranged 59% for norfloxacin to 82% for ofloxacin and 95% for doxycycline; for SAs strong cation-exchange cartridges were more efficient, recoveries were 96% for sulfamethoxazole and 43% for sulfadimethoxine. Limit of quantification ranged from 0.1 ng/g for SAs to 160 ng/g for tetracycline. Method precision for TCs was 5.06% and 1.12%, and for SAs 0.43% and 2.01%. FQs precision ranged from 0.77% to 1.89%.     

磁性氧化石墨烯的制备及其在环境水样中7种内分泌干扰物检测中的应用

制备了十二胺修饰的磁性氧化石墨烯纳米材料并将其用于磁固相萃取。在对磁固相萃取材料合成与萃取条件以及液相色谱分离等条件进行优化的基础上,建立了磁固相萃取与高效液相色谱-紫外检测对环境水样中7种内分泌干扰物的分析方法。该方法对雌酮、雌二醇、雌三醇、双酚A、17α-乙炔基雌二醇、己烷雌酚和雄烯二酮7种内分泌干扰物的检出限在0.10~0.23 nmol/L之间。将该方法分别应用于废水样品和湖水样品的加标回收试验,回收率在73.9%~112.9%和74.9%~114.7%之间。该方法操作简便,分析成本较低,可为环境水体中内分泌干扰物的分析提供技术支持。     

Determination of Natural and Synthetic Endocrine-Disrupting Chemicals (EDCs) in Sewage Based on SPE and MEKC with Amperometric Detection

An integrated analytical method to monitor five environmental endocrine disrupting chemicals (EDCs): 2,4-dichlorophenol (DCP), 4-tert-butylphenol (BP), bisphenol A (BPA), 17α-ethynylestradiol (EE2) and 4-n-nonylphenol (NP), was developed for the first time, based on a solid-phase extraction and miniaturized micellar electrokinetic chromatography with amperometric detection. In order to get the optimum conditions of their separation and detection, several parameters including pH and concentration of running buffer, concentration of micelle, separation voltage and injection time were studied and optimized. The five EDCs were well separated under the optimum conditions within 12 min. This method was successfully applied for the determination of these five EDCs in sewage influent sample. Satisfactory extraction performances from sewage sample was obtained by solid-phase extraction, using a C₁₈ cartridge. Quantitative analysis showed that DCP, BP, and BPA existed at μg L^?1 level in the selected sample, while EE2 and NP were not detected.     

Mixed aggregate-based acid-induced cloud-point extraction and ion-trap liquid chromatography-mass spectrometry for the determination of cationic surfactants in sewage sludge

Alkyl ammonium surfactants were extracted and concentrated from sludge samples using the acid-induced cloud-point extraction (ACPE) technique. Reversed-phase liquid chromatography-electrospray ionization in positive ion mode ion-trap mass spectrometry was then used for the separation, quantitation and identification of single homologues of the cationic surfactants. Variables affecting the ACPE efficiency were optimized using a spiked activated sludge. Total method recoveries ranged from 91 to nearly 100%. Detection limits for cationics in the sludge were between 40 and 75 ng/g. The analysis of cationic surfactants in activated and dehydrated sludge collected from two different sewage treatment plants revealed the presence of dialkyldimethyl, alkylbenzyldimethyl and alkyltrimethyl ammonium in the concentration range from 0.1 to 34 mg/kg. Alkylpyridinium surfactants were not detected. The persistence of alkyl ammonium surfactants in sewage sludge after treatments applied at municipal sewage plants was confirmed.     

Determination of endocrine-disrupting chemicals in the liquid and solid phases of activated sludge by solid phase extraction and gas chromatography–mass spectrometry

The highly complex matrix of activated sludge in sewage treatment plants (STPs) makes it difficult to detect endocrine-disrupting chemicals (EDCs) which are usually present at low concentration levels. To date, no literature has reported the concentrations of steroid estrogens in activated sludge in China and very limited data are available worldwide. In this work, a highly selective and sensitive analytical method was developed for simultaneous determination of two classes of EDCs, including estrone (E1), 17β-estradiol (E2), estriol (E3), 17α-ethynylestradiol (EE2), 4-nonylphenol (NP) and bisphenol A (BPA), in the liquid and solid phases of activated sludge. The procedures for sample preparation, extracts derivatization, and gas chromatography–mass spectrometry (GC–MS) quantification were all optimized to effectively determine target EDCs while minimizing matrix interference. The developed method showed good calibration linearity, recovery, precision, and a low limit of quantification (LOQ) for all selected EDCs in both liquid and solid phases of activated sludge. It was successfully applied to determine the concentrations of EDCs in activated sludge samples from two STPs located in Beijing and Shanghai of China, respectively.     

Comparison of two extraction methods for the analysis of per- and polyfluorinated chemicals in digested sewage sludge

A rapid and reliable analytical method, based on ion-pair extraction, clean-up on Envicarb cartridge and detection by liquid chromatography–tandem mass spectrometry (LC–MS/MS), was developed for determination of 17 per- and polyfluorinated chemicals (PFCs) in digested sewage sludge. Envicarb cartridge and six labeled internal standards were selected for the elimination/reduction and correction of matrix effects, respectively. As a result, the matrix effect for perfluorooctane sulfonamides (FOSAs) and perfluorocarboxylic acids (PFCAs) with carbon chain length from C6 to C14 was lowered to a range of −14% to +28%. However, the matrix effect for other analytes was still great mainly due to the absence of appropriate internal standard. Mean recoveries of the target analytes based on matrix spikes, at different spike levels (10–300 ng/g), ranged from 70% to 169%. Relative standard deviations (RSDs) were in the range of 2–20% at different spike levels. The limit of quantification (LOQ) ranged between 0.6 and 30 ng/g. The method was successfully applied to several sewage sludge samples from wastewater treatment plants nearby Zürich, Switzerland. In addition, by comparing the accuracy and precision of ion-pair extraction method and methanol extraction method, we further demonstrated that the ion-pair extraction method can be used for the analysis of PFCs in sludge samples. To our knowledge, this is the first study to extract the PFCs in sewage sludge with ion-pair method and to find unsaturated fluorotelomer carboxylic acids (FTUCAs) in sewage sludge.     

Determination of endocrine disrupting chemicals in environmental solid matrices by extraction with a non-ionic surfactant (Tween 80)

A readily applicable method based on extraction by aqueous non-ionic surfactant solutions (Tween 80) and RP-HPLC coupled to fluorescence detection, has been developed for the simultaneous determination of the phenolic endocrine disrupting chemicals (EDCs) nonylphenol (NP), nonylphenol monoethoxylate (NP1EO) and nonylphenol diethoxylate (NP2EO) and bisphenol A (BPA) in environmental solid matrices. Clean up of sample extracts was performed on Si-C18 solid phase extraction (SPE) cartridges. The overall Tween 80 extraction-SPE-RP-HPLC procedure was validated for accuracy and precision by analyzing sediment samples spiked with known amounts of EDCs. Recoveries for NP, NP1EO, NP2EO and BPA and limits of detection are in agreement with conventional extraction methods. The developed methodology was successfully applied to the analysis of target compounds in Italian river sediments, river suspended matter and benthonic macroinvertebrate organisms (oligochaetes Lumbriculus variegatus). Results confirmed that this relatively simple procedure performed satisfactorily in the determination of phenolic EDCs in environmental solid matrices of different complexity and that it can be a suitable alternative method to conventional systems even for routine analyses.     

Analysis of perfluorinated compounds in sewage sludge by pressurized solvent extraction followed by liquid chromatography-mass spectrometry

Perfluorinated compounds (PFCs) are widely used in everyday life and one of the main recipients of these compounds is waste water treatment plants (WWTPs). Due to the structure and physicochemical properties of PFCs, these compounds could be redistributed from influent water to sludge. This work reports a new validated protocol for the analysis of 13 perfluorinated acids, 4 perfluorosulfonates and the perfluorooctanesulfonamide. The present work has been focused to develop a sensitive and robust method for the analysis of 18 PFCs in sewage sludge, based on pressurized solvent extraction (PSE) followed by solid phase extraction (SPE) clean-up, analytes separation by liquid chromatography and analysis in a hybrid quadrupole-linear ion trap mass spectrometer (LC-QLiT-MS/MS) working in single reaction monitoring (SRM) mode. The final methodology was validated using a blank sewage sludge fortified at different concentration levels. The method limits of detection were ranging in general from 15 to 79 ng/kg. These values were comparable to the decision limit (CCα) and the detection capability (CCβ), which were 17-1134 ng/kg and 18-1347 ng/kg, respectively. The percentage of recovery was from 79 to 111% in the most cases at different spiked levels. Finally, the repeatability of the method was in the range 4% (PFOS and PFOA) to 25% (RSD %). In order to evaluate the applicability of the method, 5 sludge samples were analyzed. The results showed that the 18 PFCs were present in all samples. However, the concentrations for most of them were below the limits of quantification. The compound present at higher concentrations was perfluorooctanesulfonate (PFOS), which was in concentrations from 53.0 to 121.1 μg/kg. The other PFCs were at concentrations between 0.3 and 30.3 μg/kg.     

Headspace stir bar sorptive extraction followed by thermal desorption and gas chromatography with mass spectrometry to determine musk fragrances in sludge samples without sample pretreatment

A direct, simple and solvent‐free method based on headspace stir bar sorptive extraction and thermal desorption gas chromatography with mass spectroscopy was developed to determine 13 musk fragrances (six polycyclic musks, three nitro musks and four macrocyclic musks) in sludge without sample treatment. The optimal headspace stir bar sorptive extraction conditions were achieved when a polydimethylsiloxane stir bar was exposed for 45 min in the headspace of a 10 mL vial filled with 100 mg of sludge mixed with 0.2 mL of water stirred at 750 rpm at 80°C. The stir bar was then desorbed in the thermal desorption gas chromatography and mass spectrometry system, obtaining limits of detection between 5 and 30 ng/g. The method applicability was tested with sewage sludge from two urban wastewater treatment plants and from a potable water treatment plant. Results showed galaxolide and tonalide to be the most abundant musk fragrances found in wastewater treatment plants with maximal concentrations of 9240 and 7500 ng/g, respectively. Maximum concentration levels between 35 and 635 ng/g were found for musk ketone, musk moskene, traseolide, phantolide and celestolide in this kind of samples. Concentrations below the limits of quantitation of phantolide, galaxolide, tonalide and musk ketone were found in sludge from a potable water treatment plant.     

Investigation of extraction procedures and HPLC-DAD/MS for the determination of the brominated flame retardant tetrabromobisphenol A bis(2,3-dibromopropylether) in environmental samples

A method for the determination of the novel brominated flame retardant tetrabromobisphenol A bis(2,3-dibromopropylether), 1,1′-(isopropylidene)bis[3,5-dibromo-4-(2,3-dibromo-propoxy)-benzene] (TBBPA-dbpe), was developed. Technical TBBPA-dbpe was purified and the results of a thorough physical characterisation are reported. The application of APCI-MS is discussed and the fragmentation patterns are described. Quantification of TBBPA-dbpe was done by HPLC-DAD using external calibration. The validation of the method was accomplished using sediment and sewage sludge samples spiked with defined amounts of authentic TBBPA-dbpe. The average recovery rates of TBBPA-dbpe from spiked samples ranged from 35 to 91% (sediment) and from 57 to 98% (sewage sludge) depending on the respective extraction method. Pressurised fluid extraction (PFE) and fluidised bed extraction were superior to classical Soxhlet and sonication procedures and yielded recovery rates between 90 and 98% with relative standard deviations of 2%. The limits of detection (DTC), identification (ID) and determination (DTM) using HPLC-DAD were 10, 21 and 30 ng g⁻¹ in sediment and 22, 44 and 72 ng g⁻¹ in sewage sludge, respectively.