离子液体[BMIM][BF_4]水溶液比热容及热工特性分析

离子液体在化工和能源领域应用研究中,其比热及热工特性尤为重要,然而目前相关的比热数据较缺乏.研究主要对离子液体[BMIM][BF4]及其水溶液的比热容进行了测定.测试系统采用耐驰DSC204HP低温高压差热仪,测试精度较高且稳定可靠.实验测试的温度范围为273.15K~423.15K,测试的离子液体摩尔浓度分别为1.0...     

温度对吡啶离子液体性质影响的分子动力学模拟研究

运用分子动力学模拟方法研究了温度对三种吡啶离子液体[BPy][BF4]、[HPy][BF4]、[OPy][BF4]热力学性质的影响, 得到了每个体系的密度、自扩散系数、电导率和黏度等. 研究结果表明: 随着温度升高, 同一种离子液体的密度减小, 阴阳离子的自扩散系数明显增大, 电导率升高, 而黏度降低. 在同一温度下, 随着阳离子上烷基链的增长, 离子液体的密度减小, 但热力学性质的变化规律并不完全同步. 烷基链长最短的[BPy][BF4]的自扩散系数和电导率在每个温度下均为最大, 而黏度最小; 但烷基碳链更长的[OPy][BF4]和[HPy][BF4]的各种性质相差不大,甚至当温度大于323K时, 烷基链较长的[OPy][BF4]的自扩散系数比[HPy][BF4]的大.     

紫外光谱法检测水中咪唑类离子液体的含量

介绍了用紫外光谱测定水中离子液体含量的方法。测定了7种离子液体([C4mim][Cl]、[C4mim][BF4]、[C4mim][PF6]、[C5mim][Cl]、[C6mim][BF4]、[C8mim][Cl]和[C8mim][BF4])的最大吸收波长,并且绘制了校准曲线。结果表明,在实验试剂用量范围内,离子液体在波长211nm附近的吸光度与浓度呈线性关系,其线性相关系数均大于0.999。说明用紫外光谱法检测水中离子液体含量简单、快速且测定结果准确可靠。     

醋酸N-正辛基吡啶离子液体在不同溶剂中的荧光光谱分析

离子液体具有熔点低、可忽略的蒸气压、电化学窗口宽、热稳定性高和良好的导电性等独特性能,引起了化学工业和相关领域的广泛关注。离子液体具有低蒸气压,不会造成空气污染,但这并不意味着它们对环境完全无害。大多数离子液体易溶于水,可能会因为意外泄漏或通过污水进入水生环境。常用离子液体[BMIM][PF₆]和[BMIM][BF₄]的水溶液中,很容易形成氢氟酸,磷酸,具有一定的腐蚀性。将离子液体列为绿色溶剂,也需要提供其关于代谢和降解的毒性、生态毒性研究数据,或者其对环境影响的数据,离子液体在不同溶剂中的检测方法是非常重要的。离子液体的光谱分析法用量较少、方法简单、结果准确。离子液体和许多有机溶剂互溶,可形成均一、稳定的溶液。荧光检测法具有灵敏度高,选择性好,线性范围宽和受外界干扰少等优点。本工作研究了醋酸N-正辛基吡啶（OP-OAc）离子液体在水、乙醇、乙腈、乙酸等4种溶剂中的荧光光谱。研究结果表明,OP-OAc离子液体在不同溶剂中的荧光强度：I_乙酸＞I_乙腈＞I_乙醇＞I_水;最大发射波长的大小顺序：λ_{em, 水}＞λ_{em, 乙醇}＞λ_{em, 乙腈}＞λ_{em, 乙酸};它们的最大发射波长相对于激发波长发生红移;水中OP-OAc的荧光强度与浓度存在较高的相关性;当加入的甲醇、乙醇、乙腈溶剂不断增加时,OP-OAc离子液体的荧光强度增加,溶剂与水的比例为8∶2时,OP-OAc离子液体的荧光强度最强,溶剂的比例超过80%时,荧光强度突然降低;水中OP-OAc离子液体在pH 10时,荧光强度最高,在pH 14时,荧光强度最低。     

液体工质对气液热声发动机性能影响的实验研究

采用气液耦合振动是降低热声发动机谐振频率和提升其压力振幅的一种有效途径。为了研究液体工质对于气液热声发动机性能的影响,本文针对水、室温离子液体[EMIM][BF₄]、20%氯化钾溶液、40%和50%甲酸钾溶液五种液体工质进行了实验研究和分析。实验数据显示,在相同加热功率下,采用50%甲酸钾溶液时系统谐振频率最低,而水工质对应的谐振频率最高;40%甲酸钾溶液的压力振幅最大,而采用离子液体[EMIM][BF4]时系统压力振幅最小。研究结果表明:采用密度较大的液体工质可获得较低的谐振频率,而密度大、黏度小的液体工质则有利于获得更大的压力振幅。     

聚噻吩在离子液体中的电化学合成研究

在 1 丁基 3 甲基咪唑六氟磷酸盐离子液体 (BMIM)PF6 中直接电化学合成制备了聚噻吩膜 .通过红外光谱 (FT IR)和扫描电子显微镜 (SEM)对聚噻吩膜的结构和形貌进行了表征 .利用紫外可见光谱 (UV Vis)、循环伏安法 (CV)和四探针法研究了聚噻吩膜的电子和电化学特性 .研究结果表明 ,在电位 1.7～ 1.9V(相对于Ag/AgCl) ,在(BMIM)PF6 中可以制备均匀的聚噻吩膜 ,其中 ,离子液体 (BMIM)PF6 既作为溶剂又作支持电解质 ;在离子液体中制备的聚噻吩膜具有良好的稳定性和充放电能力 ,聚噻吩膜的电导率在 0 .0 1～ 0 .1S/cm .     

EMIMAC和HMIMCl及其水溶液热力学特性实验研究

离子液体+水作为吸收式制冷工质对具有诸多优点,其热力学性质是衡量工质对优劣及热力学计算的重要基础数据.本文研究两种水溶性离子液体EMIMAC和HMIMCl及其水溶液的热力学性质,主要对这两种离子液体及其水溶液的密度和比热进行测定.密度测试采用比重天平,比热测试采用耐驰DSC204HP低温高压差热仪,测试精度较高且测试系统稳定可靠.密度实验测试的温度范围为298.15～393.15K,比热实验测试温度范围为283.15～413.15K,测试的离子液体摩尔浓度分别为1,0.8,0.6,0.4,0.2,0.研究结果为这两种离子液体的吸收式制冷应用提供了可靠的热物性数据.     

温度对吡啶离子液体性质影响的分子动力学模拟研究

运用分子动力学模拟方法研究了温度对三种吡啶离子液体[BPy][BF_4]、[HPy][BF_4]、[OPy][BF_4]热力学性质的影响,得到了每个体系的密度、自扩散系数、电导率和黏度等.研究结果表明:随着温度升高,同一种离子液体的密度减小,阴阳离子的自扩散系数明显增大,电导率升高,而黏度降低.在同一温度下,随着阳离子上烷基链的增长,离子液体的密度减小,但热力学性质的变化规律并不完全同步.烷基链长最短的[BPy][BF_4]的自扩散系数和电导率在每个温度下均为最大,而黏度最小;但烷基碳链更长的[OPy][BF_4]和[HPy][BF_4]的各种性质相差不大,甚至当温度大于323 K时,烷基链较长的[OPy][BF_4]的自扩散系数比[HPy][BF_4]的大.     

气液耦合振动对热声发动机性能的影响

进行了气液耦合振动驻波型热声发动机定量模拟.重点比较分析了单纯气体振动系统和引入[EMIM][BF_4]室温离子液体作为液体活塞的气液耦合振动系统的运行参数,并考察了液体活塞的质量对热声发动机谐振频率、压力振幅以及板叠热端温度等的影响.     

1-羟乙基-3-甲基咪唑氯盐水溶液蒸汽压和凝固特性研究

1-羟乙基-3-甲基咪唑氯盐([HOEtMIM][Cl])是一种亲水性极强的离子液体,与水可以组成吸收式制冷工质对,具有良好的工业应用前景.在制冷工程应用中,离子液体水溶液的低温特性研究非常重要,包括低温段的水溶液蒸汽压数据和凝固特性,而[HOEtMIM][Cl]的相关研究缺乏.本文对水的质量分数分别为17.10%、24.29%、38.03%、49.89%、69.94%,温度范围(278.15K~408.15K)的[HOEtMIM][Cl]水溶液的汽液相平衡进行了测定;并对水的质量分数范围为1.3%~90.0%,温度范围为150K~360K的离子液体水溶液的凝固特性进行了测定,揭示其在低温应用时可能出现的固化问题.获得的蒸汽压及凝固特性数据对该离子液体水溶液应用于制冷系统设计具有重要意义.     

Thermodynamic properties of the mixtures of some ionic liquids with alcohols using a simple equation of state

In the present work, we have used a simple equation of state called the GMA EoS to calculate the density of three ionic liquid mixtures including 1-butyl-3-methylimidazolum hexafluorophosphate, [BMIM] [PF₆] + methanol, 1-butyl-3-methylimidazolum tetrafluoroborate, [BMIM] [BF₄] + methanol, and [BMIM] [BF₄] + ethanol at different temperatures, pressures, and compositions. The isothermal compressibility, excess molar volumes, and excess Gibbs molar energy of these mixtures have been computed using this equation of state. The values of statistical parameters show that the GMA EoS can predict these thermodynamic properties very well within the experimental errors. The results show that isothermal compressibility of ionic liquids is lower than alcohols and the effect of temperature and pressure on the isothermal compressibility of ionic liquids is lower than alcohols. The excess molar volumes and excess molar Gibbs energy for these ionic liquid mixtures with alcohols are all negative at various temperatures and pressures over the whole composition range. The results have been interpreted in terms of intermolecular interactions and structural factors of the ionic liquids and alcohols.     

Probing the adsorption of methylimidazole at ionic liquids/Cu electrode interface by surface‐enhanced Raman scattering spectroscopy

Two kinds of room‐temperature ionic liquids, 1‐butyl‐3‐methylimidazolium bromide ([BMIM]Br) and 1‐butyl‐3‐methylimidazolium tetrafluoroboride ([BMIM]BF₄), were used as solvent, and the adsorption of the ionic liquids themselves and of N‐methylimidazole (NMIM) were investigated by electrochemical surface‐enhanced Raman scattering (SERS) over a wide potential window. The results revealed that the cation of ionic liquid adsorbed onto Cu surface with different configurations in different potential ranges. When the potential was changed from the negative to the positive range, the orientation underwent a change from flat to vertical, and the onset potential for the orientation change was dependent on the types of anion of the ionic liquid. The ionic liquid in bulk solution exhibited a remarkable effect on the adsorption of NMIM. The electrode surface structure changed from adsorbing the ionic liquid at the negative potential to coadsorbing the ionic liquid and NMIM at relative positive potential for the [BMIM]BF₄ liquids, and formed films of NMIM at extremely positive potential. Due to the strong specific adsorption of Br⁻, the coadsorption of ionic liquid and NMIM was not observed in the system [BMIM]Br. By simulating the electrode surroundings, two surface complexes [Cu(NMIM)₄Br]Br·H₂O and [Cu(NMIM)₄](BF₄)₂ were synthesized by the electrochemical method in the corresponding ionic liquids for modeling the surface coordination chemistry of NMIM. The surface coordination configuration of NMIM and ionic liquids is proposed. Copyright © 2009 John Wiley & Sons, Ltd.     

ZnS nanoparticle synthesis and stability of 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4]) under glow discharge plasma

Ionic liquid glow discharge electrolysis for nanoparticle synthesis is an emerging nanomaterials processing technology and the stability of ionic liquid when they are in contact with plasma is an important issue. This paper discusses the stability of [BMIM][BF4] after exposing this ionic liquid to glow discharge plasma and the synthesis of cubic crystalline ZnS nanoparticles by plasma electrochemical method. Stability of the ionic liquid after plasma exposure to 20 min at 250 V is explained by their FTIR spectra and found that the ionic liquid is stable even after the plasma exposure.     

Electrospinning of polyacrylonitrile fibers from ionic liquid solution

We developed a temperature-controlled electrospinning apparatus specially for the polymers/IL system with high viscosity and surface tension and investigated the electrospinning of polyacrylonitrile (PAN)/1-butyl-3-methyl-imidazolium bromide ([BMIM][Br]) solutions. The rheological behaviors, surface tensions and conductivities of PAN/[BMIM]/[Br] solutions at different temperatures indicated that appropriately increasing the temperature is beneficial to their spinnability. It is also shown that PAN/[BMIM]/[Br] with a concentration of 3 wt%, 4 wt% and 5 wt% can be electrospun to fibers by increasing their temperatures to 70°C, 75°C or 85°C, respectively. A rotating drum composed of a dacron mesh was used as a collector in order to avoid the contraction of the wet fibers. This present study provides an alternative method for electrospinning polymer fibers.     

离子液体中聚氧化乙烯(PEO)相变过程中的氢键效应

我们把Flory-Huggins模型推广应用到聚合物/离子液体体系,研究聚氧化乙烯(PEO)在离子液体[EMIM][BF_4]中相变过程中的氢键效应,理论模型考虑了三种类型氢键(Ⅰ型:PEO-[EMIM]~+氢键,Ⅱ型:PEO-[BF_4]~-氢键和Ⅲ型:[EMIM]~+-[BF_4]~-氢键)的形成,分析了三种类型的氢键分数随温度、 PEO体积分数的变化.研究发现,三种类型的氢键分数随温度的升高而减少.在较小PEO体积分数条件下,增加PEO体积分数,Ⅰ型、Ⅱ型氢键分数轻微地减小;在较大PEO体积分数条件下,增加PEO体积分数,Ⅰ型、Ⅱ型氢键分数急剧减少.Ⅲ型氢键分数随着PEO体积分数的增加而急剧降低.由于三种氢键效应,第二维里系数A_2随温度的增加而减小.通过计算分析不同分子量的PEO在[EMIM][BF_4]中的相图发现,在PEO体积分数较低的条件下,Ⅰ型、Ⅱ型和Ⅲ型氢键是PEO相变的主要驱动力;在PEO体积分数较高的条件下,Ⅰ型和Ⅱ型氢键在PEO相变过程中起到主导作用.     

Effects of Room Temperature Ionic Liquids on Fluorescence Characteristics of 17β-estradiol and its Derivative

Previous reports have seldom concerned about the RTILs (Room temperature ionic liquids), and their effects on derivatization reaction or derivatives. In this study, we reported that the effects of four different RTILs, i.e., [EMIM]PF₆, [BMIM]PF₆, [HMIM]PF₆ and [OMIM]PF₆, on fluorescence spectra of 17 β-estradiol (E2), and its derivatization solvent dansyl chloride (DNSCl) and the derivative. [BMIM]PF₆ had a significant quenching effect on the fluorescence intensity of E2, suggesting the formation of [BMIM]PF₆/E2 complexes and possible buried E2 molecular in a more hydrophobic microenvironment. The estimated Stern-Volmer quenching constant (Ksv = 0.3519) proved that E2 quenching caused by [BMIM]PF₆ was a dynamic quenching process. Four RTILs, with different alkyl chain-length in imidazolium cation, resulted in different quenching intensities to E2 as follows: [EMIM]PF₆ > [BMIM]PF₆ > [HMIM]PF₆ > [OMIM]PF₆. At 5 mg L⁻¹ of DNSCl, [BMIM]PF₆, [HMIM]PF₆ and [OMIM]PF₆ increased the fluorescence intensities of E2 in water by 8.5, 7.6 and 6.1 times, respectively, and a 37-nm hypsochromic shift occurred. The fluorescence intensity for [BMIM]PF₆-extracted derivative of E2 increased more than two times compared with that for the control. In conclusion, this study demonstrated that above four hexafluorophosphate salt ionic liquids could be used in derivatization reaction to enhance fluorescent sensitivity in E2 trace residual analysis.     

红外光谱法和量子化学法对离子液体提取水中壬基酚的机理研究

采用红外光游法和毓子化学计算法(密度泛函B3LYP方法),分别对常见离子液体1-甲基-3-丁基咪唑六氟磷酸盐和含羟基的咪唑型离子液体提取水环境中的壬基酚的提取机理进行了研究.研究结果显示常见离子液体与壬基酚相互作用前后的红外谱图上没有氢键存在的迹象,而含羟基的离子液体在与壬基酚作用后其羟基峰发生了明显的红移.量子化学计...