Energy Transfer Electrogenerated Chemiluminescence for the Determination of Sulfite

A simple and novel electrogenerated chemiluminescence (ECL) method for the determination of sulfite has been developed based on the energy transfer ECL process. It was found that a weak ECL signal of sulfite was electrochemically generated on a platinum electrode in neutral aqueous solution. The signal was strongly enhanced by rhodamine B as an energy receptor and further enhanced by the neutral surfactant Tween 80. In 0.10M phosphate buffer solution (pH=7.5) containing 2.0×10^–6gmL^–1 rhodamine B and 0.4% (v/v) Tween 80, the ECL response to the concentration of sulfite at a potential of 0.82V was linear over a range of 1.0×10^–7gmL^–1 to 8.0×10^–6gmL^–1, and the detection limit was 5×10^–8gmL^–1. The relative standard deviation (n=11, 1.0×10^–6gmL^–1) was 3.8%. The proposed method has been successfully applied to the determination of sulfite in pharmaceutical injections and white sugar samples.     

Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Kinetics of formation,dissociation and equilibrium constants of pentacyanoaquoruthenate(II) with heterocycles

The kinetics of formation and dissociation reactions of [Ru(CN)₅L]^3– with a series of heterocyclic ligands were studied in aqueous media. In this presence of an excess of heterocycle, the observed second order rate constants were calculated from the k_obs versus [ligand] plot at =0.100m NaClO₄. Activation parameters for the formation reactions (H=28±7kJmol^–1 and S=140±35JK^–1mol^–1) are comparable for all systems, indicating a common mechanism. The kinetics of exchange of coordinated heterocycles for 1,3,5-triazine yielded a rate saturation typical of a limiting dissociative mechanism. Activation parameters of the limiting first order specific rate of dissociation reactions were H=85±7kJmol^–1 and S=18±4JK^–1mol^–1. Equilibrium constants were calculated from the second order rates of formation and pseudo-first order rates of dissociation reaction.     

Simultaneous determination of aluminium and iron in glasses,phosphate rocks and cement using first- and second-derivative spectrophotometry

First- and second-derivative spectrophoto-metric methods for the simultaneous determination of aluminium and iron in their mixtures are described. The methods are based on the colored complexes formed by aluminium and iron with hematoxylin in the presence of cetyltrimethylammonium bromide as a surfactant. The zero-crossing method has been utilized to measure the first- and second-derivative value of the derivative spectrum. Aluminium (0.05–1 gml^-1) could be determined in the presence of iron (0.09–1.6 gml^-1) and vice versa. The detection limits of aluminium and iron are 0.01 and 0.09 gml^-1, respectively in the first-derivative mode and 0.014 and 0.1 gml^-1 in the second-derivative mode. The proposed method has been applied to the simultaneous determination of aluminium and iron in glasses, phosphate rocks, cement and magnesite alloy.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Adsorptive Catalytic Voltammetry of Physcion in the Presence of Dissolved Oxygen at a Carbon Paste Electrode

A novel electroanalytical method for the determination of physcion is described for the first time. Physcion yields an adsorption catalytic voltammetric peak at –0.74V (vs. SCE) in 0.4molL^–1 NH₄Cl–NH₃·H₂O buffer solution (pH 10.5) at a carbon paste electrode (CPE). The experimental results indicated that physcion is efficiently accumulated at a CPE by adsorption. In the subsequent potential scan, physcion was reduced to a homologous anthrahydroquinone compound. The compound was then immediately oxidized to physcion by the dissolved oxygen in the solution, and then physcion was again reduced at the CPE. As a result, a cyclic catalytic reaction was established. The second-order derivative peak current is proportional to the physcion concentration in the ranges of 2.0×10^–104.0×10^–9molL^–1 (accumulation 90s) and 4.0×10^–92.0×10^–8molL^–1 (accumulation 60s). The limit of detection is 8×10^–11molL^–1 (S/N=3) for a 120s accumulation time. The method was applied to the direct determination of physcion in the medicinal plant polygonum multiflorum Thumb with satisfactory results.     

Determination of Attogram Quantities of Silver via Quenching of the Solid Substrate Room-Temperature Phosphorescence of Rhodamine B Based on the Catalysis of its Oxidation by Potassium Persulfate

A new method of SS-RTP for the determination of trace silver has been established. This method is based on the fact that Ag⁺, when activated by ,-bipyridyl (bipy) in a media of HAc–NaAc (pH=4.9), can catalyze the reaction of Rhodamine B (RhoB) oxidized by K₂S₂O₈, thus causing the Solid Substrate Room-Temperature Phosphorescence (SS-RTP) of RhoB to be quenched. The activating efficiency of bipy is 6.7 times higher than that of o-phenanthroline (phen). The reduction of the phosphorescence intensity (I_p) of RhoB is directly proportional to the concentration of Ag⁺ ions in the range of 1.6016.0agspot^–1 (0.40µLspot^–1). The regression equation of the working curve can be expressed as I_p=18.78+5.100m_Ag+ (agspot^–1) (r=0.9994, n=6), the detection limit is 0.28agspot^–1. This rapid, accurate and sensitive method has been successfully applied to the determination of trace silver in tea and human hair samples, and the results agree well with the Atomic Absorption Spectroscopy (AAS) method. The mechanism of the catalyzing reaction is also discussed.     

The Electrochemical Behavior of p-Aminophenol at a ω-Mercaptopropionic Acid Self-Assembled Gold Electrode

A -mercaptopropionic acid (MPA) self-assembled monolayer modified electrode (MPA/SAM/Au) on a gold electrode has been fabricated. The characterization of the MPA/SAM/Au was investigated using attenuated total reflection-fourier transform infrared (ATR-FTIR) and A.C. impedance. The electrochemical behaviors of p-aminophenol (p-AP) were studied at the MPA/SAM/Au by cyclic voltammetry and semi-derivative voltammetry (SDV) in BR buffer solution. The modified electrode shows excellent electrocatalytic activity for the redox of p-AP and accelerates the electron transfer rate. The diffusion coefficient (D) is 4.55×10^–6cm²s^–1. The oxidative peak current increases linearly with the concentration of p-AP in the range of 4.0×10^–88×10^–6molL^–1 and 1.0×10^–52×10^–4molL^–1 by square wave voltammetry response, respectively. The detection limit (three times the signal blank/slope) is up to 1.2×10^–8molL^–1. The modified electrode is able to eliminate the interference of p-benzenediol, o-benzenediol and o-AP at a 40-, 90- or 70-fold concentration of p-AP, and it has been satisfactorily used for the determination of the real sample.     

Electrochemical Behavior of Epinephrine at a Penicillamine Self-Assembled Gold Electrode,and its Analytical Application

The fabrication and electrochemical characteristics of a penicillamine (PCA) self-assembled monolayer modified gold electrode were investigated. The self-assembled electrode shows obvious electrocatalytic activity for the oxidation of epinephrine (EP). In phosphate buffer (pH 7.73), a sensitive oxidation peak was observed at 0.190V with the PCA modified Au electrode. The peak current is proportional to the concentration of EP in the range of 2.0×10^–56.0×10^–4molL^–1 and 5.0×10^–6 2.0×10^–4molL^–1 for cyclic voltammetry (CV) and differential pulse voltammetry (DPV) with the detection limits of 1.8×10^–7 and 1.3×10^–7molL^–1, respectively. The possible reaction mechanism is also discussed. The PCA self-assembled monolayer modified gold electrode is highly stable and can be applied to the determination of EP in practical injection samples. Application is simple, rapid and produces accurate results.     

Determination of Iron in Tap and Waste Water Using Liquid–Liquid Extraction in a Flow-Injection System

A flow-injection procedure for the determination of iron(III) in water is described. The procedure is based on the formation of an ion pair between the tetraphenylarsonium (Ph₄As⁺) (TPA) or tetrabutylammonium (But₄N⁺) (TBA) cations and the tetrathiocyanatoferrate(III) complex (TTF). This ion pair is extracted with chloroform, and the absorbance of the organic phase is measured at 503nm (for Ph₄As⁺) or 475nm (for But₄N⁺). Iron concentrations higher than 0.9×10^–6molL^–1 (50µgL^–1) can be detected in the first case, with a relative standard deviation of 1.9% (n=12), a linear application rangeof between 1.34 and 54.0×10^–6molL^–1 (75–3015µgL^–1), and a sampling frequency of 30h^–1. For the ion pair with But₄N⁺, the detection limit is 0.52×10^–6molL^–1 (29µgL^–1), with a relative standard deviation of 1.6% and a linear application range between 0.73 and 54.0×10^–6molL^–1. Under the proposed working conditions, only Pd(IV), Cu(II) and Bi(III) interfere. With the application of the merging zones technique, considerable amounts of organic reagent can be saved. The TBA method was applied to the analysis of iron(III) in tap and industrial waste waters.     

Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

Non-Aqueous Capillary Electrophoresis with Indirect Photometric Detection for Direct Analysis of Pb2+, Zn2+ and Cd2+ Ions

A new approach, based on non-aqueous capillary electrophoresis separation and indirect photometric detection, was established for the determination of the transition metal ions Pb²⁺, Zn²⁺ and Cd²⁺. Under optimized conditions, the method produced baseline separation of these three metal ions. The linear range and detection limits were 1050µM, 1.9µM for Cd²⁺; 1050µM, 2.1µM for Zn²⁺; and 20100µM, 3.8µM for Pb²⁺, respectively.     

A Comparative Study of Homemade C18 and Commercial C18 Sorbents for Preconcentration of Lead by Minicolumn Solid Phase Extraction

A comparative study of commercial C₁₈ chemically immobilized on silica and homemade C₁₈, as sorbents for Pb complexed with O,O-diethyl-dithiophosphate (DDTP) in a flow injection preconcentration system is reported. The homemade C₁₈ sorbent was obtained by sorption of poly(methyloctadecylsiloxane) (PMODS) on the silica support followed by immobilization using thermal treatment. The method follows the concept of green chemistry, since there are no toxic residues after synthesis. The complexed Pb was formed in 1.0molL^–1 HCl medium and retained on the minicolumn filled with the sorbents. The elution was carried out using ethanol, and the richest 210µL fraction was collected and analyzed by flame atomic absorption spectrometry. Chemical and flow variables were optimized for each sorbent. The results demonstrated that the performance of the proposed homemade C₁₈ sorbent for preconcentration of Pb complexed with DDTP is very similar to commercial C₁₈ chemically bonded on silica. By processing 25mL, the enrichment factors were 129 and 125 for commercial C₁₈ and homemade C₁₈, respectively. The limit of detection for commercial and homemade C₁₈ was 0.2µgL^–1 and 0.6µgL^–1, respectively. The relative standard deviation (RSD) was lower than 1.2% for both sorbents for a Pb concentration of 100µgL^–1. The method was also applied successfully to the analysis of water samples, and the accuracy was tested by recovery measurements on spiked samples and biological reference material.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Determination of Na,K, Rb and Cs Distribution in Human Brain Using Neutron Activation Analysis

This study aims to investigate the distribution of Na, K, Rb and Cs in human brains (5 individuals, 12 brain parts, mean age: 75 years). Distribution of the trace metals between lipid fraction and brain tissue was investigated in solvent extraction experiments. Determinations were carried out by instrumental neutron activation analysis. The present results show a rather non-homogeneous distribution for Na and a relatively uniform distribution for K, Rb and Cs. The mean concentrations found are 7440µgNag^–1 dry weight, 12800µgKg^–1, 14µgRbg^–1 and 50ngCsg^–1. A highly significant positive correlation was found between Rb and Cs. Solvent extraction experiments showed that 19% of Rb and 26% of Cs of the total content is located in lipid fraction.     

Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Novel tetrahedral and heteronuclear transition metal clusters prepared via single and double isolobal displacements

Ten transition metal cluster complexes with parent and substituted cyclopentadienyl ligands, [(⁵-C₅H⁴ CH₂CH₂)₂O][MFeCoS(CO)₈]₂ (2 M=Mo; 3 M=W), (⁵-C₅H₅)(⁵-RC₅H₄)MFeNiS(CO)₅ (5 M=Mo, R=Me; 6M= W, R=H), (⁵-C₅H₅)[⁵-C₅H₄C(O)CH₂]₂[WFeNiS(CO)₅][WFeCoS(CO)₈] (8), (⁵-C₅H₅)₂[⁵-C₅H₄ C(O)CH₂]₂[WFeNiS(CO)₅]₂ (9), (⁵-RC₅H₄)[(⁵-C₅H₄CH₂CH₂)₂O][Mo2FeS(CO)₇][MoFeCoS (CO)₈] (10R=MeCO; 12 R=MeO2C), (⁵-RC₅H₄)₂[(⁵-C₅H₄CH₂CH₂)₂O][Mo₂FeS(CO)₇]₂ (11 R=MeCO; 13 R=MeO2C), were synthesized through single and double isolobal displacements and characterized by elemental analyses, i.r., 1H-n.m.r. and MS techniques.     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Investigation of Medium Power Radiofrequency Capacitively Coupled Plasmas and Their Application to Atomic Emission Spectrometry for the Determination of Aluminium in Water Samples

A medium power radiofrequency capacitively coupled plasma (275W, 27.12MHz) with low argon consumption (0.5Lmin^–1) was investigated to be used for the determination of aluminium in water samples pneumatically nebulised by atomic emission spectrometry. The plasma torch was operated in two geometric configurations, coaxial and coaxial-annular with single (SRTr.f.CCP) or double ring electrodes (DRTr.f.CCP), respectively. The optimum experimental parameters (observation height, Ar flow rate, distance between ring electrodes, matrix interference of Na⁺ and Ca²⁺ and anion nature) for Al 396.152nm emission were established. Under optimum operating conditions of the DRTr.f.CCP torch (6cm distance between annular electrodes), a detection limit of 70ngmL^–1 aluminium was found. Both operating parameters and several figures of merit of the investigated plasmas were compared to those of microwave plasmas and inductively coupled plasma used in atomic emission spectrometry. The method was used to control the quality of drinking and industrial water. Samples were mineralised with 2mL of 1+1 HNO₃ and 10mL of 1+1 HCl. In the range of 0.15–3.5mgL^–1 Al³⁺ the relative standard deviation varied between 3.7 and 8.6% (n=3). For two certified drinking water samples containing 0.206 and 0.218mgL^–1 Al³⁺ the recovery (n=5) was 97.6±6.8% and 98.6±7.3%, respectively.     

Determination of cadmium and copper with ET-AAS after electrochemical deposition on a graphite electrode

The electrodeposition of cadmium and copper on a special graphite disk electrode has been performed at controlled potential. The electrode with the deposit has been inserted into the graphite atomizer HGA-400 by an adapted automatic sampler for the final determination by ET-ASS. The sensitivity of determination has been 0.371 (gl^-1)^-1 for cadmium and 0.025 (gl^-1)^-1 for copper for 2 min electrodeposition and increased linearly with the time of deposition. The limit of detection (3s_bl) has been 7.9 ngl^-1 Cd²⁺ and 0.11 gl^–1 Cu²⁺ for 2 min deposition and it has been improved with increased time of electrodeposition. The technique has been applied to the determination of both metals in seawater and to speciation in the presence of EDTA complexing agent.