Synthesis and photochemical properties of poly(ester–amide)s containing norbornadiene (NBD) residues

N,N′‐Bis[(3‐carboxynorbornadien‐2‐yl)carbonyl]‐N,N′‐diphenylethylenediamine (BNPE) was synthesized in 70% yield by the reaction of 2,5‐norbornadiene‐2,3‐dicarboxylic acid anhydride with N,N′‐diphenylethylenediamine. Other dicarboxylic acid derivatives containing norbornadiene (NBD) residues having N,N′‐disubstituted amide groups were also prepared by the reaction of 2,5‐NBD‐2,3‐dicarboxylic acid anhydride with certain secondary diamines. When the polyaddition of BNPE with bisphenol A diglycidyl ether (BPGE) was carried out using tetrabutylammonium bromide as a catalyst in N‐methyl‐2‐pyrrolidone at 100°C for 12 h, a polymer with number average molecular weight of 69,800 was obtained in 98% yield. Polyadditions of other NBD dicarboxylic acid derivatives containing N,N′‐disubstituted amide groups with BPGE were also performed under the same conditions. The reaction proceeded very smoothly to give the corresponding NBD poly(ester–amide)s in good yields. Photochemical reactions of the obtained polymers with N,N′‐disubstituted amide groups on the NBD residue were examined, and it was found that these polymers were effectively sensitized by adding appropriate photosensitizers such as 4‐(N,N‐dimethylamino)benzophenone and 4,4′‐bis(N,N‐diethylamino)benzophenone in the film state. The stored energies in the quadricyclane groups of the polymers were also evaluated to be about 94 kJ/mol by DSC measurement of the irradiated polymer films. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 917–926, 1999     

Vinyl monomers bearing chromophore moieties and their polymers. II. Fluorescence and initiation behavior of N-(4-N′, N′-dimethylaminophenyl)maleimide and its polymer

A maleimide bearing electron-donating chromophore, N-(4-N′,N′-dimethylaminophenyl)-maleimide (DMAPMI) was synthesized from N, N-dimethylaminoaniline and maleic anhydride in the presence of acetic anhydride and sodium acetate. DMAPMI can be easily copolymerized with vinyl acetate (VAc). In addition, it can be easily homopolymerized by UV light irradiation or by using AIBN or BPO as an initiator. The fluorescence spectra of DMAPMI and its polymer or copolymer were recorded and compared at the same chromophore concentrations. It was observed that the fluorescence emission intensity of DMAPMI was much lower than those of its polymers. This may be due to the occurrence of intermolecular charge transfer interaction between the electron-donating dimethylaminophenyl moiety and acrylic electron-accepting carbon-carbon double bond in the monomer. The model compound, N-(4-N′, N′-dimethylaminophenyl)succinimide (DMAPSI), which has no carbon-carbon double bond, displayed the same fluorescence behavior as DMAPMI polymers. The fluorescence of DMAPMI polymers and DMAPSI can be quenched by electron-deficient compounds such as AN, TCNE, MMA, etc. All these results supported the above conclusion. This is another example of the “fluorescence structural self-quenching effect” termed by us previously and demonstrates again that this phenomenon is not an accidental but a general one for acrylic monomers bearing electron-donating chromophores. Study of the initiation behavior of DMAPMI and its polymer showed that they could initiate the photopolymerization of AN, by combination with BPO, they could also initiate the thermopolymerization of vinyl monomers such as MMA. © 1996 John Wiley & Sons, Inc.     

Radiation degradation susceptibility of vinyl polymers: Nitriles and anhydrides

The effect of γ irradiation on a series of vinyl polymers, which included polymethacrylonitrile, poly(α-chloroacrylonitrile), poly(dimethyl itaconate), poly(acrylic anhydride), and poly(methacrylic anhydride), was studied as part of a program to develop improved positive lithographic resists. Radiation-induced degradation was observed for polymethacrylonitrile, poly(α-chloroacrylonitrile), and poly(methacrylic anhydride). Molecular weight degradation as a function of dose was monitored by membrane osmometry or GPC techniques. For γ-irradiated poly(dimethyl itaconate) and poly(acrylic anhydride) crosslinking was found to predominate over chain scission. [G(s)–G(x)] values, calculated from molecular weight inverse versus dose curves, indicate that both nitrile polymers degraded more efficiently than a poly(methyl methacrylate) reference standard on the basis of M _n changes. The radiation behavior of the first three polymers confirms earlier findings than vinyl polymers with quaternary carbons predominantly degrade when subjected to ionizing radiation.     

Synthesis and properties of poly(ether imide)s based on the bis(ether anhydride)s from hydroquinone and its derivatives

Four bis(ether anhydride)s, 4,4′‐(1,4‐phenylenedioxy)diphthalic anhydride (IV), 4,4′‐(2,5‐tolylenedioxy)‐diphthalic anhydride (Me‐IV), 4,4′‐(2‐chloro‐1,4‐phenylenedioxy)diphthalic anhydride (Cl‐IV), and 4,4′‐(2,5‐biphenylenedioxy)diphthalic anhydride (Ph‐IV), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4‐nitrophthalonitrile with the potassium phenoxides of hydroquinone and various substituted hydroquinones such as methylhydroquinone, chlorohydroquinone, and phenylhydroquinone in N,N‐dimethylformamide, followed by alkaline hydrolysis and dehydration. Four series of poly(ether imide)s were prepared from bis(ether anhydride)s with various aromatic diamines by a classical two‐step procedure. The inherent viscosities of the intermediate poly(amic acid)s were in the range of 0.40–2.63 dL/g. Except for those derived from p‐phenylenediamine and benzidine, almost all the poly(amic acid)s could be solution‐cast and thermally converted into transparent, flexible, and tough polyimide films. Introduction of the chloro or phenyl substituent leads to a decreased crystallinity and an increased solubility of the polymers. The glass transition temperatures (T_g) of these polyimides were recorded in the range of 204–263°C. In general, the methyl‐ and chloro‐substituted polyimides exhibited relatively higher T_gs, whereas the phenyl‐substituted ones exhibited slightly lower T_gs compared to the corresponding nonsubstituted ones. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500°C either in nitrogen or in air. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 665–675, 1999     

Synthesis and characterization of new highly organosoluble poly(ether imide)s based on 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride

A new bis(ether anhydride), 3,3′,5,5′‐tetramethyl‐2,2‐bis[4‐(4‐dicarboxyphenoxy)phenyl]propane dianhydride ( 3 ), was prepared in three steps: the nitro displacement of 4‐nitrophthalonitrile with 2,2‐bis(4‐hydroxy‐3,5‐dimethylphenyl)propane, the alkaline hydrolysis of the intermediate bis(ether dinitrile), and the subsequent dehydration of the resulting bis(ether diacid). A series of new highly soluble poly(ether imide)s with tetramethyl and isopropylidene groups were prepared from the bis(ether anhydride) 3 with various diamines by a conventional two‐stage synthesis including polyaddition and chemical cyclodehydration. The resulting poly(ether imide)s had inherent viscosities of 0.54–0.73 dL g^?1. Gel permeation chromatography measurements revealed that the polymers had number‐average and weight‐average molecular weights of up to 54,000 and 124,000, respectively. All the polymers showed typical amorphous diffraction patterns. All of the poly(ether imide)s showed excellent solubility and were readily dissolved in various solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, pyridine, cyclohexanone, tetrahydrofuran, and even chloroform. Most of the polymers could be dissolved with chloroform concentrations as high as 30 wt %. These polymers had glass‐transition temperatures of 244–282 °C. Thermogravimetric analysis showed that all polymers were stable, with 10% weight losses recorded above 463 °C in nitrogen. These transparent, tough, and flexible polymer films were obtained through solution casting from N,N‐dimethylacetamide solutions. These polymer films had tensile strengths of 81–102 MPa and tensile moduli of 1.8–2.0 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2556–2563, 2002     

Solution properties of poly(4,4′-oxydiphenylene)-4-amidophthalamic acid

A series of polymers based on 4-chloroformyl phthalic anhydride (TMAC) and 4,4′-diaminodi-phenylether (DAPE) was prepared and shown to be soluble in N, N-dimethylacetamide which contained 0.1N LiBr. These solutions were characterized by light scattering, membrane osmometry, and viscosity. A relationship between the viscosity and molecular weight was formulated and the nature of the polymer chain in solution was postulated.     

Thermally stable polymers based on bismaleimides containing amide,imide, and ester linkages

Seven new structurally different bismaleimides were synthesized and characterized by infrared and proton nuclear magnetic resonance spectroscopy. The chain of these polymer precursors was extended by incorporating amidized, imidized, and esterified 4-chloroformyl phthalic anhydride. The bismaleimides containing amide and imide linkages were prepared by a simple synthetic route based on the reaction of the monomaleamic acid derived from various aromatic diamines (1 mol) with 4-chloroformyl phthalic anhydride (0.5 mol) and subsequent cyclodehydration of the intermediate triamic acid. In addition, chain extended bismaleimides were prepared by reacting the monomaleamic acid derived from p-phenylenediamine with several dianhydrides such as p-phenylene bis(trimellitamide anhydride), p-phenylene bis(trimellitate anhydride), and bis-phenol A bis(trimellitate anhydride). The differential thermal analysis scans of bismaleimides showed exotherms at 221–304°C associated with their polymerization reactions. The thermogravimetric analysis traces of polymers did not show a weight loss up to 351–393 and 344–372°C in N₂ and air atmospheres, respectively. The anaerobic char yield of polymers at 800°C was 44–61%. These polymers can be used for fabrication of composites having improved properties.     

Stereoregularity of poly(alkyl α-chloroacrylates) and mechanism of isotactic polymerization

The catalytic activity of the complexes prepared by the reaction of Grignard reagents with ketones, esters, and an epoxide as polymerization catalysts of methyl and ethyl α-chloroacrylates was investigated. The modifiers which gave isotactic polymers were α,β-unsaturated ketones such as benzalacetophenone, benzalacetone, dibenzalacetone, mesityl oxide, and methyl vinyl ketone, and α,β-unsaturated esters such as ethyl cinnamate, ethyl crotonate, and methyl acrylate. Catalysts with butyl ethyl ketone, propiophenone, and propylene oxide as modifiers produced atactic polymers but no isotactic polymers. It was revealed that the complex catalysts having a structure ? C?C? O? MgX (X is halogen) gave isotactic polymers. The mechanism of isotactic polymerization was discussed. In addition, for radical polymerization of ethyl α-chloroacrylate, enthalpy and entropy differences between isotactic and syndiotactic additions were calculated to give ΔH_i^* ? ΔH_s^* = 910 cal/mole and ΔS_i^* ? ΔS_s^* = 0.82 eu.     

Synthesis and characterization of new highly organosoluble poly(etherimide)s derived from 1,1‐bis{4‐[4‐(3,4‐dicarboxyphenoxy)phenyl]‐4‐phenylcyclohexane} dianhydride

A new bulky pendent bis(ether anhydride), 1,1‐bis[4‐(4‐dicarboxyphenoxy)phenyl]‐4‐phenylcyclohexane dianhydride, was prepared in three steps, starting from the nitrodisplacement of 1,1‐bis(4‐hydroxyphenyl)‐4‐phenylcyclohexane with 4‐nitrophthalonitrile to form bis(ether dinitrile), followed by alkaline hydrolysis of the bis(ether dinitrile) and subsequent dehydration of the resulting bis(ether diacid). A series of new poly(ether imide)s were prepared from the bis(ether anhydride) with various diamines by a conventional two‐stage synthesis including polyaddition and subsequent chemical cyclodehydration. The resulting poly(ether imide)s had inherent viscosities of 0.50–0.73 dL g^?1. The gel permeation chromatography measurements revealed that the polymers had number‐average and weight‐average molecular weights of up to 57,000 and 130,000, respectively. All the polymers showed typical amorphous diffraction patterns. All of the poly(ether imide)s showed excellent solubility in comparison with the other polyimides derived from adamantane, norbornane, cyclododecane, and methanohexahydroindane and were readily dissolved in various solvents such as N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide, pyridine, cyclohexanone, tetrahydrofuran, and even chloroform. These polymers had glass‐transition temperatures of 226–255 °C. Most of the polymers could be dissolved in chloroform in as high as a 30 wt % concentration. Thermogravimetric analysis showed that all polymers were stable up to 450 °C, with 10% weight losses recorded from 458 to 497 °C in nitrogen. These transparent, tough, and flexible polymer films could be obtained by solution casting from DMAc solutions. These polymer films had tensile strengths of 79–103 MPa and tensile moduli of 1.5–2.1 GPa. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2066–2074, 2002     

New poly(amide-imide)s syntheses. VII. Preparation and properties of poly(amide-imide)s derived from 1,5-bis(4-aminophenoxy) naphthalene,trimellitic anhydride,and various aromatic diamines

New bis(phenoxy)naphthalene-containing poly(amide-imide)s having an inherent viscosity in the range of 0.62–1.09 dL/g were prepared by the direct polycondensation of 1,5-bis(4-trimellitimidophenoxy) naphthalene ( I ) and various aromatic diamines using triphenyl phosphite and pyridine as condensing agents in N-methyl-2-pyrrolidone (NMP) in the presence of calcium chloride. The diimide-diacid (I) was prepared by the condensation of 1,5-bis(4-aminophenoxy) naphthalene and trimellitic anhydride. Most of the polymers were soluble in aprotic solvents such as NMP and N,N-dimethylacetamide (DMAc), and afforded transparent, flexible and tough films upon casting from DMAc solutions. Measurements of wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or oxyphenylene groups were characterized as crystalline polymers. Tensile strength and initial moduli of the polymer films ranged from 61–86 MPa and 1.83–2.21 GPa, respectively. Glass transition temperatures of the polymers were in the range of 231–340°C. The melting points of the crystalline polymers ranged from 375–430°C. The 10% weight loss temperatures were above 512°C in nitrogen and 481°C in air. © 1993 John Wiley & Sons, Inc.     

Concurrent crystallization in polypropylene/nylon-6 blends using maleic anhydride grafted polypropylene as a compatibilizing agent

This paper describes the nonisothermal crystallization of molten blends of two semicrystalline polymers, polypropylene (PP) and Nylon-6 (N6). A discussion details the effect of the concentration of the compatibilizing agent, maleic anhydride grafted polypropylene (MAH-g-PP), on the crystallization behavior. The crystallization thermograms showed one crystallization peak or two crystallization peaks, which were significantly affected by the presence of MAH-g-PP. The crystallization temperature of N6 levels off down as the concentration of MAH-g-PP increases, whereas that of PP stays at a roughly constant temperature. These blends containing the compatibilizing agent exhibited concurrent crystallization at the crystallization temperature of PP. The crystallization behavior are also studied by optical microscopy under crossed polarizers. © 1994 John Wiley & Sons, Inc.     

Characterization of novel modified amorphous poly (ether sulphone)s

New high-temperature amorphous polymers with chlorine, amine, and maleimide chain-ends have been synthesized by nucleophilic polycondensation and fully characterized by ¹³C-NMR, ¹H-NMR, and potentiometric titration. From chain-end determination, number average molecular masses were calculated. It was confirmed that transetherification during the synthesis led to a randomized polymer of the monomer residues. For nominally amine-ended polymers obtained by addition of m-aminophenol at the end of the synthesis, a small amount of hydroxyl chain-ends was observed. This is ascribed also to transetherification. Complete reaction of the amine chain-ends with maleic anhydride was demonstrated. Reaction of hydroxyl chain-ends with acetic anhydride was also observed. The thermal stability of these different polymers was investigated; lower thermal stability was observed for amine and maleimide-ended polymers. By two different methods, a T_g around 270d°C was determined for these novel amorphous aromatic polymers. © 1994 John Wiley & Sons, Inc.     

Surface grafting of polymers onto inorganic ultrafine particles: Reaction of functional polymers with acid anhydride groups introduced onto inorganic ultrafine particles

The surface grafting onto inorganic ultrafine particles, such as silica, titanium oxide, and ferrite, by the reaction of acid anhydride groups on the surfaces with functional polymers having hydroxyl and amino groups was examined. The introduction of acid anhydride groups onto inorganic ultrafine particle was achieved by the reaction of hydroxyl groups on these surfaces with 4-trimethoxysilyltetrahydrophthalic anhydride in toluene. The amount of acid anhydride groups introduced onto the surface of ultrafine silica, titanium oxide, and ferrite was determined to be 0.96, 0.47, and 0.31 mmol/g, respectively, by elemental analysis. Functional polymers having terminal hydroxyl or amino groups, such as diol-type poly(propylene glycol) (PPG), and diamine-type polydimethylsiloxane (SDA), reacted with acid anhydride groups on these ultrafine particles to give polymer-grafted ultrafine particles: PPG and SDA were considered to be grafted onto these surfaces with ester and amide bond, respectively. The percentage of grafting increased with increasing acid anhydride group content of the surface: the percentage of grafting of SDA (M_n = 3.9 × 10³) onto silica, titanium oxide, and ferrite reaching 64.7, 33.7, and 24.1%, respectively. These polymer-grafted ultrafine particles gave a stable colloidal dispersion in organic solvents.     

New poly(amide-imide)s syntheses. VIII. Preparation and properties of poly (amide-imide)s derived from 2,3-bis(4-aminophenoxy)naphthalene,trimellitic anhydride,and various aromatic diamines

The new polymer-forming diimide-diacid, 2,3-bis(4-trimellitimidophenoxy) naphthalene (I), was readily obtained by the condensation reaction of 2,3-bis (4-aminophenoxy) naphthalene with trimellitic anhydride. A series of novel aromatic poly (amide-imide)s were prepared by the direct polycondensation of diimide-diacid I with various aromatic diamines using triphenyl phosphite in N-methyl-2-pyrrolidone (NMP)/pyridine solution containing dissolved calcium chloride. The resultant polymers have inherent viscosities in the range of 0.65–1.02 dL/g at 30°C in N, N-dimethylacetamide. These polymers were readily soluble in various organic solvents and could be cast into transparent, tough, and flexible films. Their casting films showed tensile strength at break up to 86 MPa, elongation to break of 5–9%, and initial moduli up to 2.35 GPa. The wide-angle X-ray diffraction revealed that those polymers containing p-phenylene or p-oxyphenylene group are partially crystalline, and the other polymers are evidenced as amorphous patterns. These polymers show a glass transition in the range of 213–290°C in their differential scanning calorimetry (DSC) traces. The thermal stability of the polymers was evaluated by thermogravimetry analysis, which showed the 10% weight-loss temperatures in the range of 508–565°C in nitrogen and 480–529°C in air atmosphere. © 1994 John Wiley & Sons, Inc.     

Synthesis and characterization of novel degradable photocrosslinked poly(ether‐anhydride) networks

New degradable poly(ether‐anhydride) networks were synthesized by UV photopolymerization. Dicarboxylated poly(ethylene glycol) (PEG) or poly(tetramethylene glycol) (PTMG) was reacted with an excess of methacrylic anhydride to form dimethacrylated macromers containing anhydride linkages. The percent of conversion for the macromer formation was more than 80% at 60 °C after 24 h. ¹H NMR and IR spectroscopies show the presence of anhydride linkages in the macromer. In vitro degradation studies were carried out at 37 °C in PBS with crosslinked polymer networks formed by UV irradiation. All PEG‐based polymers degraded within 2 days, while PTMG‐based polymers degraded by 50% of the initial weight after 14 days. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1277–1282, 2000     

Azo‐group labelled polyesters by end‐capping with 2‐oxazoline derivatives – photochemical properties

Two azobenzene containing 2‐oxazolines were used for labeling of a polyester with carboxylic end groups by the end‐capping method. The modification was performed under the conditions of either reactive processing or in a solution. Photochemical activity of the prepared polymers, as well as that of the modifiers was studied. The polymers prepared represent new photosensitive materials that undergo photochemical trans‐cis isomerizations and reverse cis‐trans reactions.     

Synthesis of aromatic polyamide-imides from N,N′-bis(trimethylsilyl)-substituted aromatic diamines and 4-chloroformylphthalic anhydride

The polymerization of N,N′-bis(trimethylsilyl)-substituted aromatic diamines with 4-chloroformylphthalic anhydride in various solvents at a temperature range between 10 and 70°C afforded polyamide-amic acid trimethylsilyl esters having inherent viscosities of 0.8–1.4 dL/g. Transparent and flexible films of the silylated precursor polymers were obtained by casting directly from the polymer solutions. Desilylation of the silylated polymers with methanol resulted in the formation of the corresponding polyamide-amic acids. Subsequent thermal imidization of the silylated precursor polymers with the elimination of trimethylsilanol afforded yellow, transparent, and tough films of the aromatic polyamide-imides. The thermal conversion of the silylated precursor polymer to polyamide-imide proceeded almost as rapidly as that of the corresponding polyamide-amic acid prepared by a conventional method from the parent aromatic diamine and 4-chloroformylphthalic anhydride.     

Anionic polymerization. VI. Effect of polar modifiers on alkylsodium and alkylpotassium polymerization of butadiene

It was found that N,N,N′,N′-tetramethylethylene diamine and hexamethyl phosphorus triamide minimize chain transfer reactions in the polymerization of 1,3-butadiene in hydrocarbon solvent with alkylsodium or alkylpotassium initiators. The polymers obtained with alkylsodium initiators had a high molecular weight and high vinyl content at 90–95% conversion. The molecular weight of the polybutadiene made by alkylsodium and alkylpotassium initiators was dependent on the polymerization temperatures and modifier ratios, but the vinyl contents were independent of the modifier ratios. Vinyl contents of alkylpotassium-initiated polymers showed a slight dependency on polymerization temperature; the vinyl contents of alkylsodium-initiated polymers were independent of temperature. Addition of lithium tert-butoxide and potassium tert-amylate to these initiators in the presence of the modifiers affected the molecular weight but not the microstructure.     

Synthesis and characterisation of rubbing-resistant polyimides with naphthalimide side-chain for liquid-crystal alignment layers

A novel diamine with a side-chain containing naphthalimide ring and non-polar alkyl end group, N-octyl-4-(3,5-dinitrobenzoyl)-amido-1,8-naphthalimide (N8), was synthesised and its chemical structure was confirmed by FTIR (fourier transform infrared) spectroscopy and nuclear magnetic resonance spectroscopy (¹H-NMR). Then, a new family of polyimides (PIs) containing naphthalimide unit in the side-chains has been successfully synthesised by reaction of 4,4′-oxydiphthalic anhydride (ODPA) and 3,3′-dimethyl-4,4′-methylenediamine (DMMDA) with the novel functional diamine N8. The obtained polymers showed excellent solubility in a broad range of solvents, including tetrahydrofuran. Thermal properties of polymers were good enough to permit the use of these PIs on liquid-crystal displays (LCDs) applications. Alignment films obtained by casting offered outstanding rubbing-resistant ability, meanwhile kept the pretilt angle high above 89°. The PI seems to be prospective materials for alignment layers in LCDs.     

Synthesis and nonlinear optical properties of high glass transition poly(maleimide-4-phenylstyrene)s

Nonlinear optical polymers with high T_g were prepared by polymer analogous reaction of maleic anhydride copolymers with aminoalkyl-functionalized azo chromophores. Poled films of the polymers show a good nonlinear optical response that is stable at temperatures up to 125°C.