Antiferromagnetic interactions in Er-doped SnO<Subscript>2</Subscript> DMS nanoparticles

Diluted magnetic semiconductor (DMS) nanoparticles of Sn_1−x Er _x O₂ (x = 0.0, 0.02, 0.04, and 0.1) were prepared by sol–gel method. The X-ray diffraction patterns showed SnO₂ rutile structure for all samples with no impurity peaks. The decrease in crystallite size with Er concentration was confirmed from TEM measurements (from 12 to 4 nm). The UV–Visible absorption spectra of Er-doped SnO₂ nanoparticles showed blue shift in band gap compared to undoped SnO₂. The electron spin resonance analysis of Er-doped SnO₂ nanoparticles indicate Er³⁺ in a rutile lattice and also decrease in intensity with Er concentration above x = 0.02. Temperature-dependent magnetization studies and the inverse susceptibility curves indicated increased antiferromagnetic interaction with Er concentration.     

Annealing study of electrodeposited CuInSe<Subscript>2</Subscript> and CuInS<Subscript>2</Subscript> thin films

In this study CuInSe₂ and CuInS₂ thin films were prepared onto ITO glass substrate using the electrodeposition technique in aqueous solution. The electrodeposited films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray analysis. The annealing effects on electrodeposited precursors were investigated. The chalcopyrite structure of CuInSe₂/CuInS₂ showed an enhancement of crystallinity after subsequent selenization/sulfurization treatment in Se/S atmosphere, respectively. XRD and SEM studies revealed a dramatic improvement of the crystalline quality of CIS films after annealing treatments. Mott–Schottky measurements were used to assess the conductivity type of the films and their carrier concentration. The prepared samples underwent an etching process to remove the binary accumulated Cu_2?x(Se,S) phases shown in FESEM pictures. This etching process has shown a noticeable decrease in both, the flat band potential, V_fb (V), and the number of acceptors, N_A (cm^?3) in selenized CuInSe₂ and sulfurized CuInS₂ samples.     

Synthesis of highly non-stoichiometric Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> nanoparticles with tunable bandgaps

Non-stoichiometric Cu₂ZnSnS₄ nanoparticles with average diameters of 4–15 nm and quasi-polyhedral shape were successfully synthesized by a colloidal method. We found that a non-stoichiometric composition of Zn to Cu in Cu₂ZnSnS₄ nanoparticles yielded a correlation where Zn content increased with a decrease in Cu content, suggesting formation of lattice defects relating to Cu and Zn, such as a Cu vacancy (V_Cu), antisite with Zn replacing Cu (Zn_Cu), and/or defect cluster of V_Cu and Zn_Cu. The bandgap energy of Cu₂ZnSnS₄ nanoparticles systematically varies between 1.56 and 1.83 eV depending on the composition ratios of Cu and Zn, resulting in a wider bandgap for Cu-deficient Cu₂ZnSnS₄ nanoparticles. These characteristics can be ascribed to the modification in electronic band structures due to formation of V_Cu and Zn_Cu on the analogy of ternary copper chalcogenide, chalcopyrite CuInSe₂, in which the top of the valence band shifts downward with decreasing Cu contents, because much like the structure of CuInSe₂, the top of the valence band is composed of a Cu 3d orbital in Cu₂ZnSnS₄.     

Photoluminescence of nanoparticles of (Ga<Subscript>2</Subscript>S<Subscript>3</Subscript>)<Subscript>0.95</Subscript>(Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>0.05</Subscript> solid solution

We have ground bulk samples to obtain nanoparticles of (Ga₂S₃)_1–x (Eu₂O₃) _x solid solutions, the sizes of which were determined using an atomic force microscope. The photoluminescence spectra of the nanoparticles were studied in the temperature interval 77–300 K. We have established the mechanisms for emission and transfer of energy from the matrix to the rare-earth ion, and we determined the Stokes shift (ΔS = 0.7 eV), the Huang–Rhys parameter (S = 16), and the optical phonon energy (ħ−ω = 23 meV).     

Thermal expansion and thermal conductivity of single-crystal Cu<Subscript>x</Subscript>Ag<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>InS<Subscript>2</Subscript> solid solutions grown by the moving solvent method

Single crystals of Cu_xAg_1−x InS₂ solid solutions are grown by the moving solvent method. The compositions and structures of the single crystals are determined. The thermal expansion coefficients of these crystals are determined with a dilatometer. The thermal expansion coefficients are found to vary linearly with concentration x. The thermal conductivity of the crystals is measured by the absolute method, and the concentration dependence of the thermal conductivity is constructed. This dependence is shown to have a minimum near the equimolar composition.     

Microemulsion-mediated in-situ synthesis and magnetic characterization of polyaniline/Zn<Subscript>0.5</Subscript>Cu<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocomposite

Polyaniline/Zn_0.5Cu_0.5Fe₂O₄ nanocomposite was synthesized by a simple, general and inexpensive in-situ polymerization method in w/o microemulsion. The effects of polyaniline coating on the magnetic properties of Zn_0.5Cu_0.5Fe₂O₄ nanoparticles were investigated. The structural, morphological and magnetic properties of as-prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectra, scanning electron microscopy (SEM) and magnetic measurements. The morphology analysis confirmed that polyaniline was deposited on the porous surface of magnetic Zn_0.5Cu_0.5Fe₂O₄. It was shown that the saturation magnetization and coercivity of Zn_0.5Cu_0.5Fe₂O₄ decreased after polyaniline coating, which can be interpreted by the interparticle dipole–dipole interactions that contributed to magnetic anisotropy and changed the magnetic properties of the nanoparticles. PACS  74.25.Ha; 81.05.-t; 81.05.Lg     

Enhanced photocatalytic activity of ternary CuInS<Subscript>2</Subscript> nanocrystals synthesized from the combination of a binary Cu(I)S precursor and InCl<Subscript>3</Subscript>

Ternary copper indium sulfide (CIS) nanocrystals (NCs) have been synthesized by mixing of binary precursor [Cu^I(bdpa)₂][Cu^ICl₂] (1) and/or [Cu^I(mdpa)₂][Cu^ICl₂] (2) (where, mdpa and bdpa represent methyl and benzyl ester of 3,5-dimethyl pyrazole-1-dithioic acid, respectively) with InCl₃ in a low-temperature solvothermal process. The +1 oxidation state of copper and the atomic ratio Cu to S (1:2) is atomically maintained in the pyrazole-based Cu(I)–S precursor to synthesize phase pure CuInS₂. Coordinating solvents like ethylene diamine (EN) and ethylene glycol (EG) have been used in the synthesis without any surfactants. No use of external surfactants in the synthesis of CIS nanoparticles reveals that precursor acts as stabilizing agent. The synthesized nanocrystals were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and energy dispersive X-ray spectroscopy (EDX) studies. The optical property of the nanocrystals shows a pronounced quantum confinement effect in the particles with band gap energy ca. 1.5 eV. The formation mechanism of ternary CIS has been proposed. The pore size distributions of the particles show the average pore diameters 13.1 nm from 1 and 5.3 nm from 2. The calculated values of the specific surface area are 8.123 and 9.577 m²/g for 1 and 2, respectively. The excellent photocatalytic degradation of rose bengal (RB) and rhodamine B (RhB) was demonstrated by the porous CIS nanocrystals.

Open image in new window

Graphical abstract Enhanced photocatalytic activity of ternary CuInS₂ nanocrystals synthesized from the combination of a binary Cu(I)S precursor and InCl₃. Gopinath Mondal, Ananyakumari Santra, Sumanta Jana, Nimai Chand Pramanik, Anup Mondal and Pulakesh Bera

     

Electronic structure of defective lithium cobaltites Li<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>CoO<Subscript>2</Subscript>

X-ray absorption, resonant X-ray emission, and X-ray photoelectron spectroscopical methods have been applied for the study of the electronic structure of defective lithium cobaltites Li _x CoO₂ (0.6≤x≤1.0). Resonant O K α X-ray emission spectra of LiCoO₂ showed localized excitonic states due to a dd transition between occupied and unoccupied Co 3d states. On the base of measurements of Co 3s X-ray photoelectron, Co 2p, and O 1s X-ray absorption spectra, it was established that in defective cobaltites the electronic holes are localized mainly in O 2p states. An evidence of phase separation in Li _x CoO₂ has been found. It was shown that the semiconductor-to-metal transition in Li _x CoO₂ (x<0.76) at about 160 K is not accompanied by changes in the Co 3d electronic configuration which remains 3d ⁶.     

FMR and TEM Studies of Co and Ni Nanoparticles Implanted in the SiO<Subscript>2</Subscript> Matrix

Fused silica plates have been implanted with 40 keV Co⁺ or Ni⁺ ions to high doses in the range of (0.25–1.0) × 10¹⁷ ions/cm², and magnetic properties of the implanted samples have been studied with ferromagnetic resonance (FMR) technique supplemented by transmission electron microscopy, electron diffraction and energy dispersive X-ray spectroscopy. The high-dose implantation with 3d-ions results in the formation of cobalt and nickel metal nanoparticles in the irradiated subsurface layer of the SiO₂ matrix. Co and Ni nanocrystals with hexagonal close packing and face-centered cubic structures have a spherical shape and the sizes of 4–5 nm (for cobalt) and 6–14 nm (for nickel) in diameter. Room-temperature FMR signals from ensembles of Co and Ni nanoparticles implanted in the SiO₂ matrix exhibit an out-of-plane uniaxial magnetic anisotropy that is typical for thin magnetic films. The dose and temperature dependences of FMR spectra have been analyzed using the Kittel formalism, and the effective magnetization and g-factor values have been obtained for Co- and Ni-implanted samples. Nonsymmetric FMR line shapes have been fitted by a sum of two symmetrical curves. The dependences of the magnetic parameters of each curve on the implantation dose and temperature are presented.     

Influence of Sm<Superscript>3+</Superscript> ion in structural,morphological, and electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> synthesized by microwave calcination

LiSm_xMn_2–xO₄ samples were synthesized via co-precipitation technique. The structural properties of the synthesized materials were studied using X-ray diffraction analysis and it confirmed the cubic spinel structure for all the compounds. The lattice parameter of LiMn₂O₄ was observed to be 8.2347 Ǻ and it decreased with Sm³⁺ concentration, due to the shrinkage in cell volume aided by higher binding energy between Sm-O bond. The SEM micrographs were analyzed using Image processing software (Image-J) to ascertain the pore and grain properties. The microwave synthesis had been observed to control the bulk grain formation and had yielded lesser porous and nanoparticles. The particle size distributions obtained through photocross correlation laser diffraction analysis had shown that LiMn₂O₄ with 60 nm and Sm-doped compounds with ∼30 nm, respectively. The cyclic voltammetry studies had revealed the decrease in electrocatalytic behavior in the initial cycle for compounds doped with Sm³⁺ ion. The initial capacities of LiMn₂O₄, LiSm_0.05Mn_1.95O₄ and LiSm_0.10Mn_1.90O₄ substituted compounds were observed to be 134.87 mAhg⁻¹, 132.22 mAhg⁻¹ and 126.41 mAhg⁻¹, respectively. The cells were simulated using 1D model namely Dualfoil5.1 program. The simulated results coincide well with the measured results. The cycle life studies reveal 93% capacity retention of samarium-0.05-doped samples when compared with 78.4% of the LiMn₂O₄.     

Photoinduced growth of Cu nanoparticles on ZnO from CuCl<Subscript>2</Subscript> in methanol

Cu nanoparticles were formed on surface of nano-ZnO by UV light induced photoreduction of CuCl₂ in methanol solution suspended with ZnO nanoparticles. By controlling the reaction conditions, the average size of the produced copper nanocrystal can be fine-tuned in the range of 10–200 nm. At constant UV irradiation, the Cu nanocrystals gradually grew up as the initial concentration of copper cation was increased, showing that the in situ formed Cu nanoparticles act as a bridge to facilitate the transferring of photoexcited electrons from ZnO surface to Cu²⁺ in solution. A Redox property was also proved for the Cu nanoparticles.     

One-step fastest method of nanocrystalline CuAlS<Subscript>2</Subscript> chalcopyrite synthesis,and its nanostructure characterization

Nanocrystalline CuAlS₂ chalcopyrite has been mechanosynthesized at room temperature for the first time by ball milling the stoichiometric mixture of elemental of Cu, Al, and S powders under argon atmosphere. Initially, the CuAlS₂ phase is formed by solid state reaction of elemental powders within 15 min of milling and in the course of milling crystallite size decreases slowly to ~5 nm within 10 h of milling. Microstructure characterization and phase transformation kinetics of the elemental powders toward the chalcopyrite phase formation has been made by employing the Rietveld analysis using X-ray diffraction data of unmilled and ball-milled samples.     

Structural and catalytic properties of ZnO and Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanostructures loaded with metal nanoparticles

Nanostructured zinc oxide (ZnO) nanobelts and aluminum oxide (Al₂O₃) nanoribbons have been grown successfully from the vapor phase. XRD results confirmed the purity and the high quality of the formed crystalline materials. TEM images showed that ZnO nanostructures grew in the commonly known tetrapod structure with nanobelts separated from the tetrapods with an average width range of 10–30 nm and a length of about 500 nm. Al₂O₃ nanostructures grew in the form of nanoribbons with an average width range of 20–30 nm and a length of up to 1 μm. The catalytic oxidation of CO gas into CO₂ gas over the synthesized nanostructures is also reported. Higher catalytic activity was observed for Pd nanoparticles loaded on the ZnO nanobelts (100% conversion at 270 °C) and Al₂O₃ nanoribbons (100% conversion at 250 °C). The catalytic activity increased in the order Cu < Co < Au < Pd for the metal-loaded nanostructures. The preparation methods could be applied for the synthesis of novel nanostructures of various materials with novel properties resulting from the different shapes and morphologies.     

Influence of copper intercalation on the resistive state of compounds in the Cu-HfSe<Subscript>2</Subscript> system

Polycrystalline samples of intercalated compounds Cu _x HfSe₂ have been synthesized for the first time and their electrical resistivity has been measured at both direct current and alternating current (with a frequency ranging from 200 Hz to 150 kHz) in the temperature range 80–300 K. It has been shown that the intercalation of copper atoms between three-layer Se-Hf-Se blocks leads to an increase in the electrical resistivity of the samples, as well as to a more pronounced activated character of the temperature dependence of the electrical resistivity. A time dependence of the electrical resistivity of the Cu _x HfSe₂ samples at room temperature, which is associated with the presence of copper ions in the sample, has been determined.     

EPR and optical absorption studies of Cu<Superscript>2+</Superscript> ions in [ZnPd(CN)<Subscript>4</Subscript>(C<Subscript>4</Subscript>H<Subscript>12</Subscript>N<Subscript>2</Subscript>O<Subscript>2</Subscript>)] single crystals

A Cu²⁺-doped single crystal of catena-trans-bis(N-(2-hydroxyethyl)-ethylenediamine) zinc(II)-tetra-m-cyanopaladate(II) [ZnPd(CN)₄(C₄H₁₂N₂O₂)] complex has been investigated by electron paramagnetic resonance (EPR) technique at room temperature. EPR spectra indicate that Cu²⁺ ions substitute for magnetically equivalent Zn²⁺ ions and form octahedral complexes in [ZnPd(CN)₄(C₄H₁₂N₂O₂)] hosts. The crystal field affecting the Cu²⁺ ion is nearly axial. The optical absorption studies show two bands at 322 nm (30864 cm⁻¹) and 634 nm (15337 cm⁻¹) which confirm the axial symmetry. The spin Hamiltonian parameters and the relevant wave function are determined.     

Spectral-luminescent investigations of glasses and glass-ceramic materials in Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Glasses of 2Bi₂O₃-3GeO₂-xFe₂O₃ composition, where x = 0–1.5, are obtained under oxidizing and reducing conditions. Glass-ceramic materials are produced by the thermal treatment of the glasses, the properties of which, as well as those of the original glasses, are studied by the methods of X-ray phase analysis and optical and luminescent spectroscopy. It is found that the Fe³⁺/Fe²⁺ ion ratio in the samples changes depending on the synthesis conditions of the original glasses and crystallization process.     

Synthesis and Luminescent Properties of M<Subscript>2</Subscript>V<Subscript>2</Subscript>O<Subscript>7</Subscript>: Eu (M=Sr,Ba) Nanophosphors

A solution combustion route for the synthesis of Eu³⁺-activated M₂V₂O₇ (M = Sr, Ba) and their luminescent properties have been investigated. Structure and luminescent characteristics of Sr₂V₂O₇:Eu³⁺ and Ba₂V₂O₇:Eu³⁺ nanophosphors have been studied by x-ray diffraction, scanning electron microscopy, transmission electron microscopy, fluorescence spectrometry and Fourier transform infra-red spectroscopy. The incorporation of Eu³⁺ activator in these nanoparticles has been checked by luminescence characteristics. These nanoparticles have displayed red color under a UV source which is due to characteristics transition of Eu³⁺ from ⁵D₀ → ⁷F₂ at 613 nm in both Sr₂V₂O₇:Eu³⁺ and Ba₂V₂O₇:Eu³⁺ nanophosphors. In addition, the optimal Eu³⁺ - doped contents of Sr_2(1-x)Eu_2xV₂O₇ and Ba_2(1-x)Eu_2xV₂O₇ nanophosphors for both were 4 mol%.     

Resonant photoemission and absorption spectroscopy of the Cu<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>TiSe<Subscript>2</Subscript> compound

Single crystals of the Cu _x TiSe₂ compound with x = 0.05, 0.09, and 0.33 have been grown. Resonance photoelectron Cu 3p-3d and 2d-3d spectra of the valence bands, the spectra of the core levels, and the L absorption spectra for titanium and copper have been obtained. It is shown that the degree of oxidation of titanium atoms is +4 and the state of copper atoms is close to the state of free copper ions. It is found that the spectra of the valence bands obtained under the Cu 3p and 2p resonance conditions radically differ. For the spectra in the Cu 2p excitation regime, several bands corresponding to different decay channels of the excited state are observed. According to calculations of the density of states, the 3d states of copper are filled incompletely; the occupancy of the 3d band of copper is 9.5 electrons per atom.     

Nuclear reactions in the Pd/PdO:D<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> and Ti/TiO<Subscript>2</Subscript>:D<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> systems excited by ionizing radiation

The yield of the products of nuclear reactions from deuterated palladium and titanium irradiated by an electron beam and X rays has been studied. Charged particles have been detected by CR-39 track detectors, which are not sensitive to electronic noise, electrons, and X-ray photons. To identify the type of particles and to estimate their energy, three detectors covered by aluminum and copper foils of various thicknesses have been used. It has been established with reliable statistics that 30-keV electrons and X rays initiate the synthesis of deuterons in the Pd/PdO:D _x and Ti/TiO₂:D _x systems with the yield of 3-MeV protons.     

Specific features of praseodymium-doping induced changes in the critical temperature and energy spectrum parameters of YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> in the presence of calcium ions in the lattice

The results of the experimental study of the specific features of changes in the temperature and concentration dependences of the thermopower coefficient and the critical temperature in the Y_{0.85 − x} Ca_0.15Pr _x Ba₂Cu₃O _y system as the praseodymium content increases are presented. The results obtained have been analyzed based on the narrow band model, the energy spectrum and charge carrier system parameters have been determined, and their behavior with an increase in the doping level has been analyzed. It has been found that both superconducting properties and parameters of the normal state of Y_{0.85 − x} Ca_0.15Pr _x Ba₂Cu₃O _y vary differently in various doping ranges. Based on a comparison of the results obtained with the available data for the case of single doping of YBa₂Cu₃O _y with praseodymium, conclusions have been drawn regarding the mechanism of the energy spectrum modification in the studied compound. The Fermi-level pinning effect has been revealed in the region of a local peak of the density-of-states function, and the energy position of this peak has been determined. It has been shown that the consideration of the Fermi level dynamics caused by the specific features of the structure and transformation of the Y_{0.85 − x} Ca_0.15Pr _x Ba₂Cu₃O _y energy spectrum upon doping makes it possible to explain the observed dependence of the critical temperature on the praseodymium content.