氟橡胶/改性乙丙橡胶并用胶的热稳定性

采用热分析技术考察了氟橡胶及氟橡胶(FPM)/改性乙丙橡胶(MEPDM)并用胶在氮气中的热稳定性, 通过微分法与积分法两种动力学方法计算出了FPM及FPM/MEPDM并用胶的热分解活化能E和指前因子A. 结果表明, 并用胶的热分解温度稍高于纯的氟橡胶, 但热分解活化能略低于氟橡胶, FPM、FPM/MEPDM(5%)和FPM/MEPDM(10%)的热分解活化能分别为251.74、244.98和219.60 kJ·mol-1; 热分解反应级数n均为0.95. 随着失重百分率的增大, 热分解活化能增大.     

硅橡胶/氟橡胶并用胶的制备及力学性能

硅橡胶和氟橡胶作为国防、航天等重要领域的耐热材料一直被人们青睐,但其有着各自地优缺点且价格昂贵,本文尝试将这两种橡胶制成并用胶以解决氟橡胶不耐低温和加工性差的问题,以期增大其使用温度范围。采用机械共混法制备硅橡胶/氟橡胶并用胶,研究了硅橡胶和氟橡胶的混炼工艺、并用比、共硫化体系和硫化条件对并用胶力学性能的影响。结果表明,当硅橡胶/氟橡胶的质量比为10∶90,共硫化体系为3~#硫化剂/过氧化二异丙苯(DCP),一段硫化温度为170℃、硫化压力为10MPa、硫化时间为30min,二段硫化温度为200℃、硫化时间为6h时,并用胶的力学性能达到最好。     

Aging behavior and thermal degradation of fluoroelastomer reactive blends with poly-phenol hydroxy EPDM

In this paper, the aging behavior of the reactive blends of fluoroelastomer (FPM) with poly-phenol hydroxy ethylene propylene diene monomer rubber (PHEPDM) in hot air was firstly investigated. The aging mechanism was analyzed by the swelling experiment, attenuated total-reflectance Fourier-transform infrared (FTIR-ATR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The results showed that the aging process increased the crosslinking density and the content of double bond. The O/F or O/C ratios increased and then decreased during aging because of the oxidation reaction of molecular chain and the surface migration of fluoro group. Secondly, thermogravimetric analysis (TGA) was used to study the thermal degradation behavior of the reactive blends. The apparent degradation activation energy (E) of FPM/PHEPDM reactive blends was calculated by the Kissinger and Coats-Redfern methods, respectively. The results showed that the FPM/PHEPDM reactive blends had higher thermal degradation temperature but lower E than FPM. Both the thermal degradation process of FPM/PHEPDM reactive blends and FPM were determined by nucleation and growth mechanism (Am). The general mechanism function was [−ln(1 − α)]^1/m. The optimum value of m was between 1/3 and 1/2 for FPM/PHEPDM reactive blends, but 1/2 for FPM. From the results above, it was deduced that the special structure of PHEPDM made itself surrounded by fluoroelastomer and protected from hot-air aging and thermal degradation.     

含碱性功能基聚合物反应性增容体系的研究

含碱性功能基聚合物反应性增容体系的研究胡静，张邦华，宋谋道，周庆业（南开大学高分子化学研究所，天津，３０００７１）关键词聚合物共混，反应性聚合物，碱性功能基，反应性增容通过共混单体方法制备聚合物“合金”是聚合物高性能化、开发材料新品种的主要方法。对于...     

Thermal stability and viscoelastic properties of MF/PVAc hybrid resins on the adhesion for engineered flooring in under heating system; ONDOL

The thermal properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The viscoelastic properties of the blends were also studied. Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The TGA results showed that the DTG_max temperature and thermal stability of the blends increased with increasing PVAc content. The blends were examined in non-isothermal DSC experiments at a heating rate of 10 °C/min. There was an exothermic peak in all the heating scanning curves, with each blend displaying a single curing peak temperature (T_p), intermediate between those of the two pure components and varying with the blend composition. The DMTA thermogram of MF resin showed that the storage modulus (E′) increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. E′ of MF resin increased both as a function of increasing temperature and with increasing heating rate.     

Thermal Properties of E-beam Cured Epoxy/Thermoplastic Matrices for Advanced Composite Materials

The aim of this work is to investigate the possibility to improve the thermal behaviour of epoxy based systems, cured by ionizing radiation, in order to produce matrices for advanced carbon fibres composites. Blends of two epoxy monomers, difunctional and trifunctional, have been polymerized by e-beam irradiation and the dynamic mechanical thermal properties have been investigated. The increase of the concentration of the trifunctional epoxy monomer in the blend causes a marked increase of the Tg, but strongly decreases the reactivity. Subsequently, blends of the same epoxy monomers with a high Tg thermoplastic toughening agent have been considered and their reactivity and the thermal properties of the obtained materials have been also studied. The experimental results show that the thermoplastic component increases the reactivity of the difunctional/trifunctional blends, without a significant decrease of the glass transition temperature which still satisfies the requirements for advanced composite materials.     

Blends of Poly（lactic acid） with Thermoplastic Acetylated Starch

Blends of poly(lactic acid)(PLA) and thermoplastic acetylated starch(ATPS) were prepared by means of the melt mixing method. The results show that PLA and ATPS were partially miscible, which was confirmed with the measurement of Tg by dynamic mechanical analysis(DMA) and differrential scanning calorimetry(DSC). The mechanical and thermal properties of the blends were improved. With increasing the ATPS content, the elongation at break and impact strength were increased. The elongation at break increased from...     

接枝聚乳酸/塑化淀粉共混物的制备与性能研究

为提高聚乳酸(PLA)/淀粉共混物界面作用和降低成本,引入甲基丙烯酸缩水甘油酯(GMA)接枝聚乳酸和塑化淀粉(TPS),通过挤出和注射成型制备接枝聚乳酸/塑化淀粉共混物(PLA-g-GMA/TPS)。红外光谱分析证实,GMA成功接枝到PLA分子链上。对共混物的力学性能、热机械性能、微观形貌、热性能及亲水性等进行了系统研究,结果表明,选择GMA用量为6%(接枝率为1.51%)和TPS用量为10%时的拉伸强度、断裂伸长率及弹性模量最佳,分别为42.6MPa、8.9%及260MPa。FE-SEM观察结果表明,低含量TPS中颗粒被基体包覆或嵌入,界面平整,界面结合力强。DMA和DSC结果显示,不同质量配比的PLA-g-6%GMA/TPS共混物的Tg、储存模量、结晶度、结晶温度及熔融温度仅在小范围内发生变化。吸水率和接触角结果表明,低含量TPS的共混物吸水率和接触角变化幅度均小于高含量TPS体系。     

Mechanical and thermal properties of poly(3-hydroxybutyrate) blends with starch and starch derivatives

Poly(3-hydroxybutyrate) (PHB) is a highly crystalline, biodegradable and biocompatible thermoplastic. However, its limited utilization as a commodity plastic is associated to both high cost and very poor mechanical properties. Blending PHB with a natural polymer, such as starch, is one way to improve its properties and to get low price raw materials, though they are not miscible since there are no strong interactions between the hydrophilic starch and the hydrophobic PHB. In this study binary blends of PHB were prepared with natural starch, starch-adipate and grafted starch-urethane derivatives. The PHB blends were characterized in terms of their mechanical and thermal properties. For all blends a decrease of the Young modulus was observed as compared to the pure PHB. However, blends containing natural starches and starch adipate resulted in brittle materials. A significant decrease of both glass transition temperature (Tg) and melting point (Tm) was observed for all formulations. The best results, lower modulus and Tg were obtained with grafted starch-urethane blends using poly(propylene glycol).     

HTPB/增塑剂玻璃化转变温度及力学性能的分子动力学模拟

为了预测高分子粘结剂端羟基聚丁二烯(HTPB)与增塑剂癸二酸二辛酯(DOS)、硝化甘油(NG)的相容性及HTPB/增塑剂共混物的玻璃化转变温度(Tg)和力学性能,在COMPASS力场条件下采用分子动力学(MD)模拟方法对相容体系(HTPB-DOS)和不相容体系(HTPB-NG)进行了研究.结果表明,通过比较溶度参数差值(Δδ)的大小可以预测HTPB与增塑剂的相容性,即HTPB与DOS属于相容体系,而HTPB与NG不相容.通过温度-比容曲线可以得到HTPB、HTPB/DOS与HTPB/NG的Tg分别为197.54,176.30和200.03K.力学性能分析结果表明,添加DOS增塑剂后使HTPB的弹性模量(E),体积模量(K)和剪切模量(G)下降,材料刚性减弱,柔性增强,力学性能得到改善.本模拟方法可以作为预测聚合物/增塑剂共混物性能的有利工具,也可以为固体推进剂和高聚物粘结炸药的配方设计提供理论指导.     

双氰胺固化环氧树脂的研究

<正> 双氰胺做为环氧树脂的固化剂,其贮存期可以达到一年以上,这种固化物的机械和介电性能优异,因此,广泛用于制造层压等电工材料方面。国外许多人都曾对双氰胺与环氧树脂的固化反应历程和固化物的性能做过研究,指出了在固化过程中化学结构的变化     

磺化丁基橡胶离聚体及其共混物的动态力学性质

<正> 含10％摩尔以下的离子且主链为柔性的离聚体是一种热塑性弹性体。在动态力学性质方面呈现特殊的行为,表现在贮能模量(1gE′)与温度的关系中有橡胶态平台出现。最早Otocka等指出,(丁二烯-甲基丙烯酸)共聚物无橡胶态平台,经金属离子中和后产生橡胶态平台,且E′增加。Agarwal,Makowski等则报道磺化乙丙胶离聚体的橡胶态平台随离子含量提高而加宽,随硬脂酸锌的加入而缩短。Fitzgerald及Weisst结合X-射线小角散射研究了甘油及邻苯二甲酸二辛酯对磺化聚苯乙烯离聚体的动态力学性质的影响。     

热处理条件对R-PET/LLDPE-g-MA共混物中PET玻璃化转变行为的影响

对回收聚对苯二甲酸乙二酯(R-PET)/LLDPE-g-MA马来酸酐改性的线性低密度聚乙烯共混物进行不同条件的热处理, 采用差示扫描量热仪(DSC)研究共混物基体PET的玻璃化转变行为. 结果表明, 当热处理温度低于PET的玻璃化转变温度(Tg)时, PET的玻璃化转变区域出现热焓松弛现象. 随着热处理温度的增加, PET的Tg逐渐升高; 在50~70 ℃下热处理48 h后, PET的Tg逐渐稳定. 当热处理温度高于PET的Tg而低于100 ℃时, PET的玻璃化转变区域出现2个热流转变, FTIR分析表明, PET分子构象开始发生变化. 当热处理温度为100 ℃时, DSC曲线上PET的玻璃化转变消失, PET的结晶度明显增加, 说明PET开始冷结晶的温度在90~100 ℃之间.     

聚环氧乙烷(PEO)与聚醋酸乙烯酯(PVA)的共混研究

动态力学谱研究表明熔融共混PVA/PEO体系的无定形态中存在着纯PEO及PVA/PEO的相容或部分相容相。相容或部分相容相的T_g随共混物组成的变化远高于按照FOX方程的计算值。用结晶和分子间相互作用解释了这种对FOX方程的偏离。应用FTIR差示光谱技术对PVA/PEO共混物和PVA/DGDE浓溶液的研究证实了PVA分子链上酯基和PEO分子链存在着强的相互作用。     

SYNTHESIS, CHARACTERIZATION AND PROPERTIES OF ORGANOCLAY-MODIFIED POLYSULFONE/EPOXY INTERPENETRATING POLYMER NETWORK NANOCOMPOSITES

Organoclay-modified hydroxylterminated polysulfone (PSF)/epoxy interpenetrating network nanocomposites (oM-PSF/EP nanocomposites) were prepared by adding organophilic montmorillonite (oMMT) to interpenetrating polymer networks (IPNs) of polysulfone and epoxy resin (PSF/EP) using diaminodiphenylmethane (DDM) as curing agent.The mechanical properties like tensile strength,tensile modulus,flexural strength,flexural modulus and impact properties of the nanocomposites were studied as per ASTM standards.Differ...     

Studies on partial compatibility of PP and PS

<正>Blends of polystyrene(PS) and polypropylene(PP) were prepared through melt compounding.With an increase of PS content up to 30 wt%,the tensile strength of PP/PS blends increased from 37.4 MPa to 42.2 MPa,although the blends were widely regarded as immiscible.The DSC results showed that there's slight decrease in melting temperature of PP, showing insufficient evidence for partial compatibility between PP and PS.Almost no variation of distinct characterization peaks were observed in FTIR spectra of PS/PP blends compared with those of neat PP and PS,indicating there is no chemical interactions between PP and PS.Since the morphology investigation showed a droplet structure as PS content was up to 30 wt%,the improvement of tensile strength could be simply considered as due to the reinforcing effect of dispersed rigid PS particles on the PP,combining with partial compatibility between them as evaluated by change of C_p at glass transition for both PS and PP.More interestingly,DSC and DMA results showed that the blending of PS and PP could lead to a substantial decrease of the glass transition temperature(T_g) of PP,and increase of T_g of PS.The annealing experiment was carried out to understand the change of T_g in PP/PS blends.It is believed that the compressive stress generated by the contracting PP should be the dominant mechanism for the T_g elevation of PS.On the other hand,the T_g decrease of PP is likely owing to the creation of a large amount free interface of PP and the dilatation of the PP phase resulting from the corresponding tension exerted by PS during cooling.     

聚氯乙烯－丁腈橡胶－氯丁橡胶三元共混物的研究

测定了聚氯乙烯（ＰＶＣ）－丁腈橡胶（ＮＢＲ－２９）－氯丁橡胶（ＣＲ）三元共混物的冲击性能和应力－应变行为，用动态力学分析、扫描电镜和透射电镜研究了共混物的相容性和形态结构，结果表明，ＮＢＲ－２９对ＰＶＣ，ＣＲ有良好的增容作用，三元共混物是部分相容的二相体系，具有良好的抗冲击性能。     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

醋酸纤维素／聚乙烯基吡咯烷酮共混体系的相容性研究（Ⅰ）

用ＤＳＣ，ＤＭＴＡ研究了醋酸纤维素（ＣＤＡ），聚乙烯基吮咯烷酮（ＰＶＰ）及ＣＤＡ／ＰＶＰ共混体系的玻璃化转变行为．用精密量热法测定了该体系的混合热焓．结果表明：共混体系只存在一个玻璃化转变温度（Ｔｇ），其值随共混组成的变化而改变；共混体系的混合热焓为负值，其绝对值随组成中ＰＶＰ含量的增加而减少．力学性能研究表明，共混体系具有协同效应．上述试验结果证明，ＣＤＡ和ＰＶＰ是一对相容性高聚物．     

醋酸纤维素／聚乙烯基吡咯烷酮共混体系的相容性研究（Ⅰ）

 用ＤＳＣ，ＤＭＴＡ研究了醋酸纤维素（ＣＤＡ），聚乙烯基吮咯烷酮（ＰＶＰ）及ＣＤＡ／ＰＶＰ共混体系的玻璃化转变行为．用精密量热法测定了该体系的混合热焓．结果表明：共混体系只存在一个玻璃化转变温度（Ｔｇ），其值随共混组成的变化而改变；共混体系的混合热焓为负值，其绝对值随组成中ＰＶＰ含量的增加而减少．力学性能研究表明，共混体系具有协同效应．上述试验结果证明，ＣＤＡ和ＰＶＰ是一对相容性高聚物．