Tunable single-mode pulsed Ti3+:Sapphire laser injection-seeded by a continuous-wave Cr3+:LiSrAlF6 laser

Spectrally pure high-power tunable single-mode operation of a pulsed Ti³⁺:sapphire laser by a tunable injection-seeding is reported. The injection laser was a cw diode laser pumped, spectrally narrowed tunable Cr³⁺:LiSrAlF₆ (Cr³⁺:LiSAF) laser with a grating in the auxiliary cavity. Single-mode tunable operation of a pulsed Ti³⁺: sapphire ring oscillator was obtained at different wavelengths in the range between 818 nm and 848 nm with a typical linewidth of 0.006 cm^-1. To extend the applicability of this operation to a differential absorption lidar system, the single-mode Ti³⁺:sapphire oscillator output was amplified and a high energy output of 38 mJ was obtained with the same linewidth.     

Laser-diode-pumped Yb:YAG laser as a new pump source and its application to an Er3+, Yb3+-codoped high-output-power fiber amplifier

We propose a laser-diode-pumped Yb:YAG laser as a novel practical fiber amplifier pump source, and describe its first successful application of high-output-power operation (850 mW=+29.3 dB m) of an Er³⁺,Yb³⁺-codoped fiber amplifier at 1.55 μm. We have developed both bulk and microchip Yb:YAG lasers and obtained 3.3 W and 2.7 W, respectively, in the cw mode at room temperature. Laser-diode-pumped Yb:YAG lasers are shown to have a potential applicability to such fiber amplifiers as Pr³⁺-doped amplifiers and Tm³⁺-doped amplifiers, as well as Er³⁺,Yb³⁺-codoped fiber amplifiers. Received: 12 August 1999 / Revised version: 3 September 1999 / Published online: 20 October 1999     

Diode-pumped passively Q-switched Nd:GdVO4 lasers operating at 1.06 μm wavelength

With a 10-W diode laser to pump Nd:GdVO₄ crystal in a folded cavity, we demonstrated Cr⁴⁺:YAG passively Q-switched Nd:GdVO₄ lasers at 1.06 μm. The maximum average output power of 2.1 W and the highest peak power of 625 W were, respectively, obtained when the initial transmissions of the Cr⁴⁺:YAG crystals were 90% and 80%. Received: 8 September 1999 / Revised version: 30 December 1999 / Published online: 8 March 2000     

A global design of high power Nd-Yb co-doped fiber lasers

A global optimization method - niche hybrid genetic algorithm (NHGA) based on fitness sharing and elite replacement is applied to optimize Nd³⁺-Yb³⁺ co-doped fiber lasers (NYDFLs) for obtaining maximum signal output power. With a objective function and different pumping powers, five critical parameters (the fiber length, L; the proportion of pump power for pumping Nd³⁺, η; Nd³⁺ and Yb³⁺ concentrations, N_Nd and N_Yb and output mirror reflectivity, R_out) of the given NYDFLs are optimized by solving the rate and power propagation equations. Results show that dividing equally the input pump power among 808 nm (Nd³⁺) and 940 nm (Yb³⁺) is not an optimal choice and the pump power of Nd³⁺ ions should be kept around 10-13.78% of the total pump power. Three optimal schemes are obtained by NHGA and the highest slope efficiency of the laser is able to reach 80.1%.     

LD-pumped passively Q-switched Nd:YVO4/YVO4 laser with an Nd3+:Cr4+:YAG saturable absorber

By using a piece of codoped Nd³⁺:Cr⁴⁺:YAG crystal as a saturable absorber, a laser-diode pumped passively Q-switched Nd:YVO₄/YVO₄ laser has been realized. The maximum laser output power of 2.452 W has been obtained at the incident pump power of 8.9 W for an 8.8% transmission of the output coupler at 1064 nm, corresponding to a slope efficiency of 30%. The other output laser characteristics of the laser have also been investigated. The laser with a Nd³⁺:Cr⁴⁺:YAG saturable absorber has a lower threshold pump power and a higher slope efficiency compared to that with a similar small-signal transmission of a Cr⁴⁺:YAG saturable absorber.     

Optimization of Yb3+-doped double-clad fiber lasers using a new approximate analytical solution

We investigated the properties of continuous wave (CW) Yb³⁺-doped double-clad fiber lasers (DCFLs) with linear-cavities theoretically and numerically using the rate equations. Under steady-state conditions, a new approximate analytical solution for CW Yb³⁺-doped double-clad fiber lasers (DCFLs) with consideration of the scattering losses were deduced. Good agreement between the proposed solution and the numerical simulation was demonstrated. Compared with the known approximate solutions published in the literature, the proposed solution has a briefer expression, higher accuracy and wider scope of application, which extends the applicable range of the analytical result to low reflective feedback mirror configurations. The solution provides a clear physical understanding of the optimal design of the CW Yb³⁺-doped DCFLs and can be applied to different pump and output configurations. Using the proposed solution, the optimal design of the CW Yb³⁺-doped DCFLs was discussed. If cavity reflectivities are given in advance, the optimal fiber length is found to be independent of the pump power. When the pump power and reflectivity of the feedback end are known in advance, the results show that the optimal fiber length increases and the optimal reflectivity of output mirror decreases with increase in pump power. Furthermore, when the feedback mirror is highly reflective, there exists a certain tolerance of the optimal parameters, in which the conversion efficiency decreases only slightly. But the conversion efficiency is sensitive to reflectivity of output mirror if feedback mirror has low reflectivity.     

Continuous-wave broadly tunable Cr:ZnSe laser pumped by a thulium fiber laser

We describe a compact, broadly tunable, continuous-wave (cw) Cr²⁺:ZnSe laser pumped by a thulium fiber laser at 1800 nm. In the experiments, a polycrystalline ZnSe sample with a chromium concentration of 9.5 × 10¹⁸ cm⁻³ was used. Free-running laser output was around 2500 nm. Output couplers with transmissions of 3%, 6%, and 15% were used to characterize the power performance of the laser. Best power performance was obtained with a 15% transmitting output coupler. In this case, as high as 640 mW of output power was obtained with 2.5 W of pump power at a wavelength of 2480 nm. The stimulated emission cross-section values determined from laser threshold data and emission measurements were in good agreement. Finally, broad, continuous tuning of the laser was demonstrated between 2240 and 2900 nm by using an intracavity Brewster cut MgF₂ prism and a single set of optics.     

Continuous-wave Ho:GdVO4 laser pumped by Tm-doped fiber laser with a fiber Bragg grating at room temperature

We reported the Ho:GdVO₄ laser pumped by Tm-doped laser with a fiber Bragg grating. 2.03 W continuous-wave Ho:GdVO₄ laser output power is obtained under 10.5 W incident pump power, with the optical-to-optical conversion efficiency and slope efficiency of 19.3% and 32.3%, respectively, at 7 °C. We can see that, the lower the temperature is, the better the laser output character is. The beam quality factor is M² ∼ 1.29 measured by the traveling knife-edge method.     

A microchip-laser-pumped DFB-polymer-dye laser

A miniaturized, high repetition rate, picosecond all solid state photo-induced distributed feedback (DFB) polymer-dye laser is described by applying a passively Q-switched and frequency-doubled Cr⁴⁺:Nd³⁺:YAG-microchip laser (pulse width Δτ=540 ps, repetition rate ν=3 kHz, pump energy E_pump=0.15 μJ) as a pump source. A poly-methylmethacrylate film doped with rhodamine B dye serves as active medium. The DFB-laser pulses are temporally and spectrally characterized, and the stability of the thin polymer/dye film at high repetition rates is analyzed. The shortest DFB-laser pulses obtained have a duration of 11 ps. After the emission of 350000 pulses the intensity of the DFB-laser output has decreased by a factor of two and the pulse duration has increased by a factor of 1.2. For single DFB-laser pulses of 20-ps duration the spectral bandwidth is measured to be Δλ=0.03 nm, which is only 0.005 nm above the calculated Fourier limit assuming a Gaussian profile for the temporal shape of the pulses. Coarse wavelength tuning of the DFB laser between 590 and 619 nm is done by turning the prism. Additionally, a fine tuning of the DFB-polymer-laser wavelength is achieved by changing the temperature of the polymer/dye layer (=-0.05 nm/°C) in the range from 20 to 40 °C. Received: 1 March 2001 / Revised version: 23 May 2001 / Published online: 18 July 2001     

High power single-longitudinal-mode operation in a twisted-mode-cavity laser with a c-cut Nd:GdVO4 crystal

A twisted-mode-cavity laser was established by using a piece of c-cut Nd:GdVO₄ crystal as the lasers active material. Output spectra were scanned by a scanning Fabry–Perot interferometer, which demonstrated that the single-longitudinal-mode laser operation was realized in the twisted-mode-cavity laser configuration. A maximum single-longitudinal-mode laser output power of 2.1 W was obtained when the pump power was 11.5 W. The pump slope efficiency was about 20.0%. A passively Q-switched single-longitudinal-mode laser was also achieved in a twisted-mode cavity by inserting a piece of Cr⁴⁺:YAG as an intracavity saturable absorber. The Q-switched single-longitudinal-mode laser pulse duration was measured to be 100 ns and the single-pulse energy was about 40.0 J.     

In-band pumped Er:YAG ceramic laser with 11 W of output power at 1645 nm

We report on a high power polycrystalline Er:YAG ceramic laser in-band pumped by a cladding-pumped Er, Yb fiber laser wavelength locked at 1532 nm with a volume Bragg grating. Using 1.0 at % Er³⁺-doped ceramic as the gain medium and an output coupler of 10% transmission, the laser had a threshold pump power of ∼1.5 W and generated 11 W of continuous-wave output at 1645 nm for 23.3 W of incident pump power at 1532 nm, corresponding to a slope efficiency with respect to incident pump power of 51%.     

Laser-diode-pumped Cr4+, Nd3+:YAG self-Q-switched laser with high repetition rate and high stability

A diode end-pumped self Q-switched Cr⁴⁺, Nd³⁺: YAG laser was established with 30-ns pulse width (FWHM) and 0.5-μJ pulse energy output. In normal pulse pumping operation, the lasing threshold changed greatly from 122 mJ to 2.4 mJ as the pump pulse frequency varied from 1 Hz to 500 Hz due to pumping-induced thermal effect. A pre-pumping method was proposed and the change of the lasing threshold was reduced; programmable Q-pulse output with maximum frequency of 16 kHz and high stability was achieved. Received: 16 January 2001 / Revised version: 21 May 2001 / Published online: 19 September 2001     

A Novel 1,066 nm Nd:Gd<Subscript>0<Emphasis Type="Italic">.</Emphasis>69</Subscript>Y<Subscript>0<Emphasis Type="Italic">.</Emphasis>3</Subscript>NbO<Subscript>4</Subscript> Passively <Emphasis Type="Italic">Q</Emphasis>-Switched Pulse-Burst Laser

We demonstrate for the first time a Cr⁴⁺:YAG passively Q-switched 1066 nm pulse-burst laser under 879 nm direct pump with a novel Nd:Gd_0.69Y_0.3NbO₄ crystal. The output laser characteristics with different pump repetition rates and different Cr⁴⁺:YAG initial transmission are studied. Without the Cr⁴⁺:YAG, we obtain a maximum output energy of 2.55 mJ at an absorbed pump energy of 5.79 mJ with the highest 48% slope efficiency. The pulse-burst laser contains a maximum of 7 pulses for a Cr⁴⁺:YAG initial transmission of 55% and a pump repetition rate of 1 kHz. The single-pulse energy and narrowest pulse width reach 160 μJ and 5.5 ns at 38.2 kHz, with a peak power of 32 kW.     

Diode-pumped ultra-short-pulse solid-state lasers

Many materials are good candidates for diode-pumped ultra-short-pulse lasers: several transition-metal-ion-doped crystals can or could support extremely short fs pulses. This goal, so far, has only been reached by Cr³⁺:LiSAF, but there are good chances for other crystals like Cr⁴⁺:YAG having its bandwidth within the third communication window, and the high-yield Cr²⁺:ZnSe with its impressive bandwidth in the near IR. Rare-earth-ion-doped media deliver only sub-ps pulses but allow unprecedented and scalable high average powers, like a SESAM mode-locked Yb:YAG thin-disk laser described recently. In all ranges of pulse durations there are fascinating applications ready for widespread employment as soon as compact, reliable and moderately priced ultra-short-pulse systems will be available for the non-laser-skilled user. The highest impact in the near future is attributed to microstructuring of materials and processing of biological samples, including dental enamel, by ps and sub-ps pulses, and optical coherence tomography needing pulses in the 10-fs regime at very modest average powers. Received: 29 June 2000 / Published online: 6 December 2000     

Efficient passively Q-switched operation of a diode-pumped Nd:GGG laser with a Cr:YAG saturable absorber

The continuous-wave (cw) and passive Q-switching operation of a diode-end-pumped gadolinium gallium garnet doped with neodymium (Nd:GGG) laser at 1062 nm was realized. A maximum cw output power of 6.9 W was obtained. The corresponding optical conversion efficiency was 50.9%, and the slope efficiency was determined to be 51.4%. By using Cr⁴⁺:YAG crystals as saturable absorbers, Q-switching pulse with average output power of 1.28 W, pulse width of 4 ns and repetition rate of 6.2 kHz were obtained. The single-pulse energy and peak power were estimated to be 206 μJ and 51.6 kW, respectively. The conversion efficiency of the output power from cw to Q-switching operation was as high as 84.7%.     

Intracavity frequency-doubled diode-pumped Nd : LaSc3(BO3)4 lasers

 An intracavity frequency-doubled 10%Nd : LaSc₃(BO₃)₄ (Nd : LSB) laser was investigated in different resonator configurations and in different operation modes under continuous wave (cw) and quasi-cw laser-diode pumping. With a Cr⁴⁺ : YAG passive modulator and a KTP crystal the second-harmonic output power at 531 nm amounted to 190 mW in Q-switched TEM₀₀ mode at 750 mW of pump power. In a sandwich resonator, when all the optical elements were in direct contact with each other, 0.8 W of green output power was obtained in cw mode under 2.7 W of pump power with a slope efficiency of 44%. In the same setup under fiber-coupled diode-laser array pumping (5.6 W of incident power), 1.2 W of green output power was achieved in cw mode and 1.4 W in quasi-cw mode. Received: 30 April 1996/Revised version: 1 July 1996     

Characteristics of a passively Q-switched Nd:NaY(WO4)2 laser with Cr:YAG saturable absorber

By using xenon flash lamp as pump source and Cr⁴⁺:YAG as passive Q-switcher, we have performed the Q-switched laser operation at 1.06 μm with an Nd³⁺:NaY(WO₄)₂ (known as Nd:NYW) crystal. Meanwhile, the pulse width, the single pulse energy and the repetition rate under different small-signal transmissions of Cr⁴⁺:YAG and different reflectivities of output reflector are measured, and the numerical solutions of the coupling wave rate equations agree with the experimental results.     

Passively Q-switched diode-pumped Cr:YAG/Nd:GdVO4 monolithic microchip laser

The realization of high repetition rate passively Q-switched monolithic microlaser is a challenge since a decade. To achieve this goal, we report here on the first passively Q-switched diode-pumped microchip laser based on the association of a Nd:GdVO₄ crystal and a Cr⁴⁺:YAG saturable absorber. The monolithic design consists of 1 mm long 1% doped Nd:GdVO₄ optically contacted on a 0.4 mm long Cr⁴⁺:YAG leading to a plano-plano cavity. A repetition rate as high as 85 kHz is achieved. The average output power is approximately 400 mW for 2.2 W of absorbed pump power and the pulse length is 1.1 ns.     

Thermal lens effects in an Er<Superscript>3+</Superscript>:YAG laser with crystalline fiber geometry

A resonantly diode-pumped high-power continuous-wave Er³⁺:YAG laser with a crystalline fiber geometry based on total-internal-reflection pump guiding is reported. Up to 9.4 W of output power could be generated and a slope efficiency of 46.8% was achieved. Intrinsic efficiencies reached up to 48.8% and an optimum outcoupling of ∼20% was found. A strong thermal lens was observed and cavity stability and hysteresis effects were studied.