A polymeric microchip with integrated tips and in situ polymerized monolith for electrospray mass spectrometry

We describe the integration of a cyclo-olefin polymer based microchip with a sheathless capillary tip for electrospray ionization-mass spectrometry (ESI-MS). The microchip was fabricated by hot embossing and thermal bonding. Its design includes a side channel for adjusting the composition of the electrospray solution so that analytes in 100% water can be analyzed. The fused silica capillaries, used for sample introduction, and the electrospray tips for MS coupling were directly inserted into the microchannel before thermal bonding of the device. A microfabricated on-chip gold microelectrode was used to apply the electrospray voltage. Annealing the device after thermal bonding increased the pressure resistance of the microchip. The cross section of the microchannel was imaged by scanning electron microscopy to estimate the effects of the annealing step. The relationship between the applied electrospray voltages and MS signal was measured at different flow rates by coupling the device to an ion trap mass spectrometer. The performance of the microchip was evaluated by MS analysis of imipramine in ammonium acetate buffer solution by direct infusion. An alkylacrylate based monolith polymer bed for on-chip sample pretreatment and separation was polymerized in the microchannel and tested for ESI-MS applications.     

Atmospheric molded poly(methylmethacrylate) microchip emitters for sheathless electrospray

Disposable poly(methylmethacrylate) (PMMA) sheathless electrospray microchip emitters were prepared for the first time using the atmospheric molding fabrication protocol. A sheathless electrospray from uncoated channel outlets, machined to cone-shaped three-dimensional tips, is demonstrated utilizing a simple cross design with an on-chip liquid junction to obviate the need for external unions to voltage electrodes, thus reducing the dead volume effects as well as the complexity of fabrication. The fast replication of microchip emitters was performed by molding prepolymeric methylmethacrylate solutions into silicon-master/aluminum-spacer/glass-plate molds followed by UV-initiated free radical polymerization. The performance of the new microchip emitters was demonstrated for mass spectral measurements of methionine enkephalin, adrenocorticotropic hormone and insulin peptide/protein mixtures. The samples were infused through capillary connections using hydrodynamic pumping. The polymeric emitters prepared by this flexible fabrication route offer an easy way of operation and high stability, without a need for attachment of external voltage unions or metallizing the emitter tips. The new approach should provide a useful low-cost tool for widespread coupling of mass spectrometry to chip systems.     

Microfabricated PDMS multichannel emitter for electrospray ionization mass spectrometry

A novel microfabricated multichannel emitter for electrospray ionization mass spectrometry (ESI-MS) was implemented with polydimethylsiloxane (PDMS) using a soft lithography technique. The emitters are formed as electrospray tips along a thin membrane on the edge of the device with channels of 100 microm x 30 microm dimensions. The electrospray performance of the PDMS emitters for a single channel device and a four channel device interfaced with a time-of-flight mass spectrometer was evaluated for detecting the molecular weight of reference peptides (angiotensin I and bradykinin). The emitters were durable at the flow rate of 1-20 microL min(-1) for more than 30 h of continuous electrospray with limit of detection of 1 microM (S/N 18). This microfabrication method for a PDMS multichannel emitter as an integral part of a microfluidic device will facilitate development of more complex microfluidic analysis systems using ESI-MS.     

Comparison between different sheathless electrospray emitter configurations regarding the performance of nanoscale liquid chromatography-time-of-flight mass spectrometry analysis

Four different sheathless electrospray ionization (ESI) configurations were investigated for a nano liquid chromatography (LC) system. The studied configurations were: a column with an integrated emitter, with the ESI potential applied before or after the column, and a column with separate emitter, with the ESI voltage applied at a union before the emitter or at the emitter tip. The results indicates that the efficiency of the LC system is rather independent of the configuration when using 95 microm i.d. columns, acetic mobile phase and standard peptides as a sample. Introduction of post column dead volume seems not to be a critical issue at least with flow rates down to 600 nl/min.     

Sample pretreatment on a microchip with an integrated electrospray emitter

This study presents a microbead-packed PDMS microchip with an integrated electrospray emitter for sample pretreatment prior to sheathless ESI-MS. We prove the concept of analytical functions integrated onto a cm-sized area of a single bulk material. The microchip consists of two PDMS substrates replicated from SU-8 fabricated silicon wafer masters, bonded together after oxidation by corona discharge treatment. The channel within the microchip contains a grid structure that was used to trap 5 microm hypercross-linked polystyrene beads. The beads acted as a medium for sample desalting and enrichment. Electrical contact for the sheathless ESI process was achieved by coating the integrated emitter with conductive graphite powder after applying a thin layer of PDMS as glue. The coating as well as the bond of the PDMS structures showed excellent durability. A continuous spray was obtained from the microchip for over 800 h in a long-term electrospray stability experiment. Desalting and enrichment of neuropeptides from a physiological salt solution was successful by loading the sample onto the packed beads, followed by a washing and an eluting step. The results were obtained and evaluated using a TOF MS. An LOD of approximately 20 fmol (loaded onto the beads) for angiotensin II was obtained from a sample of neuropeptides dissolved in physiological salt solution.     

Microfabricated isoelectric focusing device for direct electrospray ionization-mass spectrometry

A novel microfabricated device for isoelectric focusing (IEF) incorporating an optimized electrospray ionization (ESI) tip was constructed on polycarbonate plates using laser micromachining. The IEF microchip incorporated a separation channel (50 micro x 30 micro x 16 cm), three fluid connectors, and two buffer reservoirs. Electrical potentials used for IEF focusing and electrospray were applied through platinum electrodes placed in the buffer reservoirs, which were isolated from the separation channel by porous membranes. Direct ESI-mass spectrometry (MS) using electrosprays produced directly from a sharp emitter "tip" on the microchip was evaluated. The results indicated that this design can produce a stable electrospray and that performance was further improved and made more flexible with the assistance of a sheath gas and sheath liquid. Error analysis of the spectral data showed that the standard deviation in signal intensity for an analyte peak was less than approximately 5% over 3 h. The production of stable electrosprays directly from microchip IEF device represents a step towards easily fabricated microanalytical devices. Microchannel IEF separations of protein mixtures were demonstrated for uncoated polycarbonate microchips. Direct microchannel IEF-ESI-MS was demonstrated using the microfabricated chip with an ion-trap mass spectrometer for characterization of protein mixtures.     

A simple and robust conductive graphite coating for sheathless electrospray emitters used in capillary electrophoresis/mass spectrometry.

A graphite-polyimide mixture was used as a conductive coating for sheathless electrospray emitters. The coating procedure described is simple and inexpensive compared to previously described methods. An investigation of the stability of the conductive coating carried out by electrochemical methods revealed good performances during oxidative stress. In addition, no decrease in emitter performance was seen during continuous electrospray in the positive electrospray mode for two weeks. Fast capillary electrophoresis with attomole sensitivity demonstrated the excellent performance of the described sheathless interface when used in conjunction with an orthogonal time-of-flight mass spectrometer. The overall simplicity, stability and low cost of this type of sheathless emitter make the described approach highly suitable for any on-column coupling of low flow rate separation techniques to a mass spectrometer.     

Capillary electrophoresis coupled to mass spectrometry from a polymer modified poly(dimethylsiloxane) microchip with an integrated graphite electrospray tip

Hybrid capillary-poly(dimethysiloxane)(PDMS) microchips with integrated electrospray ionization (ESI) tips were directly fabricated by casting PDMS in a mould. The shapes of the emitter tips were drilled into the mould, which produced highly reproducible three-dimensional tips. Due to the fabrication method of the microfluidic devices, no sealing was necessary and it was possible to produce a perfect channel modified by PolyE-323, an aliphatic polyamine coating agent. A variety of different coating procedures were also evaluated for the outside of the emitter tip. Dusting graphite on a thin unpolymerised PDMS layer followed by polymerisation was proven to be the most suitable procedure. The emitter tips showed excellent electrochemical properties and durabilities. The coating of the emitter was eventually passivated, but not lost, and could be regenerated by electrochemical means. The excellent electrochemical stability was further confirmed in long term electrospray experiments, in which the emitter sprayed continuously for more than 180 h. The PolyE-323 was found suitable for systems that integrate rigid fused silica and soft PDMS technology, since it simply could be applied successfully to both materials. The spray stability was confirmed from the recording of a total ion chromatogram in which the electrospray current exhibited a relative standard deviation of 3.9% for a 30 min run. CE-ESI-MS separations of peptides were carried out within 2 min using the hybrid PDMS chip resulting in similar efficiencies as for fused silica capillaries of the same length and thus with no measurable band broadening effects, originating from the PDMS emitter.     

A multilayer poly(dimethylsiloxane) electrospray ionization emitter for sample injection and online mass spectrometric detection

An ESI emitter made of poly(dimethylsiloxane) interfaces on-chip sample preparation with MS detection. The unique multilayer design allows both the analyte and the spray solutions to reside on the device simultaneously in discrete microfluidic environments that are spatially separated by a polycarbonate track-etched, nanocapillary array membrane (NCAM). In direct spray mode, voltage is applied to the microchannel containing a spray solution delivered via a syringe pump. For injection, the spray potential is lowered and a voltage is applied that forward biases the membrane and permits the analyte to enter the spray channel. Once the injection is complete, the bias potential is switched off, and the spray voltage is increased to generate the ESI of the injected analyte plug. Consecutive injections of a 10 microM bovine insulin solution are reproducible and produce sample plugs with limited band broadening and high quality mass spectra. Peptide signals are observed following transport through the NCAM, even when the peptide is dissolved in solutions containing up to 20% seawater. The multilayer emitter shows great potential for performing multidimensional chemical manipulations on-chip, followed by direct ESI with negligible dead volume for online MS analysis.     

Comparison of sheathless and sheath-flow electrospray interfaces for the capillary electrophoresis-electrospray ionization-mass spectrometry analysis of peptides

Capillary electrophoresis coupled to mass spectrometry via an electrospray interface provides a powerful system for separation and characterization of a high number of biomolecules. The present paper describes a home-made sheathless interface and compares it with a commercial sheath-flow interface, using a separation method based on a peptide hormone mixture of therapeutic interest. In a previous work, we optimized the parameters involved in a sheath-flow interface and obtained good results in sensitivity and reproducibility. The sheathless interface is performed with a graphite-coated electrospray ionisation (ESI) tip attached to the separation capillary. We demonstrate that electrolyte composition is the main parameter affecting signal sensitivity and separation resolution. The effect of the nature and concentration of the organic solvent added to the separation electrolyte is carefully studied. Furthermore, a general comparison of both interfaces is made in terms of separation, reproducibility, and sensitivity obtained under the optimized conditions described. Advantages and disadvantages of both coupling setups have been evaluated.     

A new on-chip ESI nozzle for coupling of MS with microfluidic devices

This paper presents a new on-chip electrospray ionisation (ESI) nozzle, which can be used as an interface for coupling microfluidic devices with mass spectrometric (MS) detection. The nozzle was micromilled in a polymer foil (polymethylmethacrylate (PMMA) 750 microm thick), normally used as a cover for microfluidic chips. The performance of this device was examined in the ESI-MS analysis of the tetrapeptide MRFA (methionine-argenine-phenylalanine-alanine). The spray quality is basically dependent on the inner diameter of the nozzle, beside the part of the organic modifier in the solution to be sprayed. Three different inner nozzle diameters (30, 50, 100 microm) and two different apex angles were investigated. Stable electrospray conditions can be generated with a relative standard deviation less than 10% of the total ion current, and down to a concentration of 0.01 micromol L(-1). The production of this ESI interface is relatively simple for the purpose of a low-cost batch fabrication of miniaturized analytical instruments.     

Glycoscreening by on-line sheathless capillary electrophoresis/electrospray ionization-quadrupole time of flight-tandem mass spectrometry

An analytical approach based on sheathless on-line coupling of capillary electrophoresis (CE) and electrospray ionization (ESI) quadrupole time-of-flight (QTOF) mass spectrometry (MS) has been developed for providing new insight into the characterization of carbohydrate mixtures. The home-built sheathless CE/     

Expanded use of a battery-powered two-electrode emitter cell for electrospray mass spectrometry

A battery-powered, controlled-current, two-electrode electrochemical cell containing a porous flow-through working electrode with high surface area and multiple auxiliary electrodes with small total surface area was incorporated into the electrospray emitter circuit to control the electrochemical reactions of analytes in the electrospray emitter. This cell system provided the ability to control the extent of analyte oxidation in positive ion mode in the electrospray emitter by simply setting the magnitude and polarity of the current at the working electrode. In addition, this cell provided the ability to effectively reduce analytes in positive ion mode and oxidize analytes in negative ion mode. The small size, economics, and ease of use of such a battery-powered controlled-current emitter cell was demonstrated by powering a single resistor and switch circuit with a small-size, 3 V watch battery, all of which might be incorporated on the emitter cell.     

Different quantitation approaches for xenobiotics in human urine samples by liquid chromatography/electrospray tandem mass spectrometry

The potential of liquid chromatography combined with tandem mass spectrometry (LC/MS/MS) for the determination of pesticide metabolites in human urine at the sub-ppb level is explored. Metabolites from two organophosphorous pesticides, 4-nitrophenol (from parathion and parathion-methyl) and 3-methyl-4-nitrophenol (from fenitrothion), are taken as model analytes to conduct this study. After direct injection of the urine sample (10 microL), different approaches were evaluated in order to achieve correct quantitation of analytes using an electrospray ionisation (ESI) interface. Thus, the feasibility of using external calibration was checked versus the use of different isotope-labeled internal standards. The advantages of applying coupled-column liquid chromatography (LC/LC) as an efficient clean-up without any type of sample manipulation are also discussed. The combination of LC/LC with ESI-MS/MS allows the direct analysis of free metabolites in urine, as the automated clean-up performed by the coupled-column technique is sufficient for the removal of interferences that suppress the ionisation of analytes in the ESI source. Using this procedure with external calibration, good precision and recoveries, and detection limits below 1 ng/mL are reached with analysis run times of around 8 min. The hyphenated technique LC/LC/ESI-MS/MS is proved to be a powerful analytical tool, allowing the rapid, sensitive and selective determination of 4-nitrophenol and 3-methyl-4-nitrophenol in human urine without any sample treatment.     

Differential ionisation of natural antioxidant polyenes in electrospray and nanospray mass spectrometry

Carotenoids are natural products with high economic relevance for the pharmaceutical industries and are a common subject for biochemical research. Reported here is a comparative study of the ionisation of carotenoids by electrospray mass spectrometry (ESI-MS) and nanospray mass spectrometry (nanoESI-MS). The results demonstrate that, along with solvent choice, the influence of the different ionisation processes of ESI and nanoESI are fundamental in determining how ionisation is achieved and which ions (molecular ion or protonated molecule) are observed in MS. The increased understanding afforded by this study will help in the development of unequivocal microanalytical methods for carotenoids and related antioxidant polyenes.     

An integrated micropump and electrospray emitter system based on porous silica monoliths

The work presents the design of an integrated system consisting of a high-pressure electroosmotic (EO) micropump and a microporous monolithic emitter, which together generate a stable and robust electrospray. Both the micropump and electrospray emitter are fabricated using a sol-gel process. Upon application of an electric potential of sufficient amplitude (>2 kV), the pump delivers fluids with an electroosmotically induced high pressure (>1 atm). The same potential is also harnessed to electrostatically generate a stable electrospray at the porous emitter. Electrokinetic coupling between pump and spray produces spray features different from sprays pressurized by independent mechanical pumps. Four typical spray modes, each with different drop sizes and charge-to-mass ratios, are observed and have been characterized. Since the monolith is silica-based, this integrated device can be used for a variety of fluids, especially organic solvents, without the swelling and shrinking problems that are commonly encountered for polymer monoliths. The maximum pressure generated by a 100 microm id monolithic pump is 3 atm at an applied voltage of 5 kV. The flow rate can be adjusted in the range of 100 nL/min to 1 microL/min by changing the voltage. For a given applied voltage across the pump and emitter system, it is seen that there exists one unique flow rate for which flow balance is achieved between the delivery of liquid to the emitter by the pump and the liquid ejection from the emitter. Under such a condition, a stable Taylor cone is obtained. The principles that lead to these results are also discussed.     

Characterization of microstructured fibre emitters: in pursuit of improved nano electrospray ionization performance

Full-dimensional computational fluid dynamics (CFD) simulations are presented for nano electrospray ionization (ESI) with various emitter designs. Our CFD electrohydrodynamic simulations are based on the Taylor-Melcher leaky-dielectric model, and the volume of fluid technique for tracking the fast-changing liquid-gas interface. The numerical method is first validated for a conventional 20 μm inner diameter capillary emitter. The impact of ESI voltage, flow rate, emitter tapering, surface hydrophobicity, and fluid conductivity on the nano-ESI behavior are thoroughly investigated and compared with experiments. Multi-electrospray is further simulated with 2-hole and 3-hole emitters with the latter having a linear or triangular hole arrangement. The simulations predict multi-electrospray behavior in good agreement with laboratory observations.     

On-line size-exclusion chromatography/electrospray ionisation mass spectrometry of aquatic humic and fulvic acids

Isolated aquatic humic and fulvic acids were analysed with on-line size exclusion chromatography/electrospray ionisation mass spectrometry (SEC/ESI-MS). An eluent composition which enabled electrospray ionisation was identified. The SEC separation improved interpretability of mass spectra and may open up new possibilities for molecular weight determination of humic substances. A linear dose-response relationship over a factor of 20 was obtained and the limit of detection was 50ng/uL for humic and fulvic acids. Spectral changes due to different ionisation conditions (pH and cone voltage) were investigated. A natural water sample from a Swedish lake was analysed. Copyright 2000 John Wiley & Sons, Ltd.     

Electron ionisation and electrospray ionisation mass spectrometric study of a series of isomeric methyl-, dimethyl- and trimethylalloxazines

Electron ionisation (EI) mass spectra and electrospray ionisation (ESI) mass spectra at different cone voltages of a series of isomeric methyl- and dimethylalloxazines are discussed, and compared with those of lumichrome, and 1- and 3-methyllumichrome. Examination of ESI mass spectra taken at a higher cone voltage and the use of isotope-labelled methanol allow us to discuss the fragmentation pathways of [M+H]+ and [M-H](-) ions. The fragmentation pathways of all of the compounds and the characteristic fragment ions formed in EI-MS are compared with published data. The influence of methyl and dimethyl substituents in the benzene ring on the fragmentation pathways leading to the loss of 43 and 45 Da upon both electron and electrospray ionisation is described.     

Studying the reducing potencies of antioxidants with the electrochemistry inherently present in electrospray ionization-mass spectrometry

In this proof-of-principle study, the applicability of electrospray ionization-mass spectrometry (ESI-MS) to characterize the reducing potencies of natural antioxidants is demonstrated. The ESI source represents a controlled-current electrochemical cell. The interfacial potential at the emitter electrode will be at or near the electrochemical potential of those reactions that sufficiently supply all the required current for the ESI circuit. Indicator molecules prone to oxidation in ESI such as amodiaquine were used to visualize the impact of reducing compounds on the interfacial potential. The extent of inhibition of the oxidation of the indicator molecule was found to be dependent on the kind and amount of antioxidant added. Concentration–inhibition curves were constructed and used to compare reducing potencies and to rank antioxidants. This ranking was found to be dependent on the electrode material–indicator molecule combination applied. For fast and automated characterization of the reducing potencies of electrochemically active molecules, a flow-injection system was combined with ESI-MS. Liquid chromatography was used to process complex biological samples, such as red and white wine. Due to their high content of different polyphenols, red wine fractions were found to exhibit higher reducing potencies than the corresponding white wine fractions. Furthermore, for 14 important natural antioxidants, the results obtained with the controlled-current EC–ESI-MS assay were compared to those obtained with chemical antioxidant assays. Irrespectively of the kind of assay used to test the reducing potency, gallic acid, quercetin, and epicatechin were found to be potent reductants. Other antioxidants performed well in one particular assay only. This observation suggests that different kinds of redox and antioxidant chemistry were assessed with each of the assays applied. Therefore, several assays should be used to comprehensively study antioxidants and their reducing potencies.