流动注射氢化物发生原子吸收光谱法测定蒙药中硒

研究测定蒙药中硒的新方法。蒙药消化液用盐酸还原处理将六价硒转化为四价硒 ,以硼氢化钾为还原剂 ,稀盐酸为载液 ,用流动注射氢化物发生原子吸收光谱法测定硒。方法的检出限为 0 .12ng·ml- 1,线性范围为 0 .6 0～ 35 .0 0ng·ml- 1,相对标准偏差为 4 .7%～ 6 .4 % ,样品加标回收率为 96 .6 %～ 10 2 .1% ,此法具有灵敏度高、选择性好、试剂及样品用量少、操作简便、快速等优点     

人发中硒的流动注射-氢化物发生原子吸收光谱法测定

在选择了头发最佳消化方法、硒氢化物生成及检测最佳条件的基础上 ,将流动注射 (FI)、氢化物发生(HG)技术与蒸汽发生原子吸收光谱法 (VGA -AAS)有机地结合起来 ,建立了人发中硒含量的测定方法 ;该法简便、快速、灵敏度高 ,测定的相对标准偏差 (n=6)为1.8 %～3.1 %,试样加标回收率为97 %～102 % ,硒的检出限为0.25μg·L-1,用于实际人发样品中硒的测定 ,结果令人满意     

磁芯-硫脲壳聚糖微柱在线流动注射-原子吸收光谱法测定大米中痕量镉

本文将磁芯-硫脲壳聚糖作为固定相填充到自制的微柱中,采用流动注射在线分离富集与火焰原子吸收法联用对大米中痕量镉进行测定。pH=7.0的试液以3.9mL/min速率采样120s,以0.5mol/L HNO3-0.1mol/L硫脲作为洗脱液,用火焰原子吸收光谱法测定洗脱液中Cd2+,检测的线性范围为0.02~1.20μg/mL(r=0.9922),检出限(3σ)为2.5ng/mL,相对标准偏差(RSD)为0.79%(c=1.0μg/mL,n=7),加标回收率在96.0%~104.2%之间。     

流动注射氢化物发生-原子吸收光谱法测定中药中的微量砷

探讨了流动注射氧化物发生-原子吸收光谱法测定微量砷的最佳条件,建立了中药中微量砷的流动注射氧化物发生-原子吸收光谱分析方法。砷的检出限为0.59μg/L,线性范围为0～30μg/L,线性回归方程为A=0.02228c 6.282×10~(-3),相关系数r=0.9992,相对标准偏差为2.6％～4.4％,回收率为91％～103％。方法操作简便、快速,灵敏度及自动化程度高。     

流动注射氢化物-原子吸收光谱法测定人发中砷

砷是一种对人体有害的元素,砷的测定方法报道较多。对发砷的测定,本文在文献[1,2]的基础上采用流动注射氢化物 原子吸收光谱法,方法操作简便快捷,提高了灵敏度和准确度,是一种较好的测定生物样品中砷的分析技术。1　试验部分1.1　仪器与试剂WFX 1D型原子吸收分光光度计(北京第二光学仪器厂)高性能砷空心阴极灯,WHG 102A型流动注射氢化物发生器,电热式T型石英管原子化器(北京翰时制作所)。砷标准储备液:1.00mg·ml-1,称取As2O3(于110℃烘干2h)0.1320g,加200g·L-1NaOH溶液2.0ml,加水50ml溶解后,加盐酸10ml,定容至100ml。使用时稀释…     

单沸消解蒸馏-流动注射氢化物发生-原子吸收光谱法测定大米、小麦粉中的汞

通过单沸消解蒸馏结合以H2O2-H2SO4-混合催化剂为消解体系的有机试样快速分解技术,实现了大米、小麦粉中汞的快速、完全提取,建立了FIHAAS法测定大米、小麦粉中汞的样品前处理和仪器分析方法.方法加标回收率为96.2%～105.3%.     

断续流动氢化物发生原子荧光法测定富硒食品中的微量硒

建立了断贯流动氢化物发生原子荧光法测定富硒食品中微量硒的方法。样品用硝酸高氯酸混酸消化，在优化的实验条件下，标准曲线的线性范围为0-100μg/L，相关系数为0.9999。检测限0.06545μg/L。应用于测定鸡蛋，富硒米和富硒盐中微量硒的测定。回收率分别为90.6%,98.5%和104.3%。     

流动注射氢化物发生-原子吸收光谱法 测定镍基合金中的硒和锡

建立了流动注射氢化物发生-原子吸收光谱法测定高温镍基合金中痕量硒和锡的方法。样品用HNO3和HF经微波消解后,制成以EDTA作掩蔽剂的碱性溶液(pH12～13),用标准加入法测定。方法测定硒和锡的检出限分别为1.0μg     

流动注射在线液—液萃取原子吸收光谱法测定生物样品中的铅

本文利用所设计的一种新型流动注射液－液萃取重力分相器，建立了流动注射液溶剂萃取原子吸收光谱法测定铅的新方法，详细地研究了流动注射在线萃取的实验条件及流路系统，方法的精密度和检出限分别为２．５％（ｎ＝１１）和２．８μｇ／Ｌ（ｋ＝３）。用拟定的方法测定了峰蛹，粮食等生物样品中的铅，结果与参考值相吻合。     

流动注射氢化物发生原子吸收光谱法测定发铅

发样消化液用铁氰化钾预先氧化处理将二价铅氧化为四价形态铅,以硼氢化钾为还原剂,稀盐酸为载液,用流动注射氢化物发生原子吸收光谱法测定铅。方法的检出限为0.26ng·ml-1,线性范围为0.60～35ng·ml-1,相对标准偏差为2.5%～4.7%,样品加标回收率为96.8%～104.4%,对人发标准物质进行测定,结果与标准值符合。方法灵敏度高、选择性好、试剂及样品用量少、操作方便快速,有推广应用价值。     

石墨炉原子吸收光谱法测定蚕蛹中Cr、Se量

建立了石墨炉原子吸收光谱法测定蚕蛹中Cr、Se的方法,为蚕蛹新资源食品的开发及明确其营养价值提供科学数据。利用石墨炉原子吸收光谱法,偏振塞曼效应扣除背景,石墨炉程序升温方式进行Cr、Se的原子化,检测峰值吸收。加入硝酸镍、吐温X-100为基体改进剂,在体积分数0.5%HNO3介质中对桑蚕蛹中Cr、Se进行测定。方法的精密度:4.0%(Cr),3.1%(Se)。加标回收率:96.8%~105.3%(Cr),92.1%~108.8%(Se)。Cr、Se的线性范围和检出限分别为:0~10μg/L(Cr),0~40μg/L(Se);LOD=1.22μg/L(Cr),1.86μg/L(Se)。建立的分析方法适用于蚕蛹中Cr、Se的测定。     

Determination of selenomethionine by high performance liquid chromatography-direct hydride generation-atomic absorption spectrometry

A simple, reliable, trace determination of selenomethionine (Semet) based on a direct hydride generation atomic absorption spectrometric method was developed using sodium tetrahydroborate (0.3% in 0.2% NaOH) and hydrochloric acid (3 M). The method excluded any chemical pretreatment prior to hydride generation (HG). The optimized HG system was successfully coupled with the HPLC system. The detection limit (3σ of blank; n=5), reproducibility (R.S.D. of three successive analyses/day, performed on three different days), and repeatability (R.S.D. of three successive analyses) of the method were 1.08 ng ml⁻¹, 9.8% for 9.04 ng ml⁻¹ and 2.1–9.5% for 30.0–1.27 ng ml⁻¹ Semet as Se (standards prepared in Milli-Q water). Calibration graph was linear up to 30 ng ml⁻¹. This HPLC-HG-AAS method is very promising and successfully determined Semet (spiked) in human urine.     

Flow injection-hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth

A simple and robust flow injection system which permits low sample and reagent consumption is described for rapid and reliable hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth. The system, which composed of one peristaltic pump and one four channel solenoid valve, used water as the carrier streams for both sample and NaBH₄ solution. Rapid off-line pre-reduction of the analytes was achieved by using hydroxylamine hydrochloride for selenium and a mixture of potassium iodide and ascorbic acid for arsenic and bismuth. Transition metal interference was eliminated with the addition of thiourea and EDTA into the NaBH₄ solution and significant sensitivity enhancement was observed for selenium in the presence of thiourea in the reductant solution. Under optimised conditions, the method achieved detection limits of 0.2 ng mL⁻¹ for Se, 0.5 ng mL⁻¹ for As and 0.3 ng mL⁻¹ for Bi. The method was very reproducible, achieving relative standard deviations of 6.3% for Se, 3.6% for As and 4.7% for Bi, and has a sample throughput of 360 h⁻¹. Successful application of the method to the quantification of selenium, arsenic and bismuth in a certified reference river sediment sample is reported.     

Indirect determination of free cyanide in water and industrial waste water by flow injection-atomic absorption spectrometry

A simple and rapid flow injection system is proposed for indirect determination of cyanide by flame atomic absorption spectrometry. It consists of a microcolumn of immobilized salen (N,N′-bis(salicylidene)ethylenediamine) on sodium dodecyl sulfate (SDS)-coated alumina saturated with silver ion and a carrier of dilute solution of sodium hydroxide (10⁻⁵ mol L⁻¹). The micro-column was located between the injection valve and nebulizer of atomic absorption spectrometry. Injection of 250 μL of aqueous cyanide standard or sample solution at pH range of 9–11 cause elution of silver as silver cyanide complexes, which was then measured by flame atomic absorption spectrometry. The absorbance was proportional to the concentration of cyanide in the sample. The graph of absorbance (as peak height) vs. cyanide concentration was linear over the concentration range of 0.1–10 mg L⁻¹ of cyanide, and the detection limit was 0.06 mg L⁻¹. The relative standard deviation at 1 and 3 mg L⁻¹ of cyanide concentration were 4.1 and 4.7%, respectively. The method was successfully applied to determination of cyanide in water and industrial waste waters, and the accuracy was examined through independent analysis by accepted method of pyridine-barbituric acid.     

Calibration by the gradient ratio-standard addition method in flow injection flame atomic absorption spectrometry

A calibration method has been developed which is realised in the flow injection analysis (FIA) by the gradient technique. According to this method two transient peaks, one for a sample and the other for a sample with standard addition, are recorded and compared point by point in the entire defined time range. The analytical result is estimated on the basis of information gained about the local analyte concentrations in the sample zone. The method allows the results to be reliable when both the non-linear calibration dependence and the interference effect occur. As an example, calcium in synthetic samples containing silicon, phosphate, aluminium, vanadium and titanium, and also in iron ore sample, were determined by flame atomic absorption spectrometry (FAAS). It has been proved, that the method can be effective in overcoming even extremely strong interferences, providing analytical results with average accuracy equal to ca. 5% and with precision 2–3 times inferior to that obtained by conventional FI calibration.     

在线还原富集火焰原子吸收光谱法测定环境水样中Cr(Ⅲ)和Cr(Ⅵ)的形态

采用单阀双阳离子交换树脂微柱并联，设计了双路采样逆向洗脱在线分离富集系统，该系统与原子吸收测量技术相结合，实现了在线分离富集-火焰原子吸收光谱法同时测定水中Cr(Ⅲ)和Cr(Ⅵ)，富集1min时，分析速度为60样/h，测定Cr(Ⅲ)和Cr(Ⅵ)的特征浓度分别为6．08μg/L和11．58μg/L(相当于1％吸收)，线性范围分别为0～1．0μg/mL和0～2．0μg/mL，对质量浓度为100μg/L的Cr(Ⅲ)和Cr(Ⅵ)测定的相对标准偏差分别为2．9％和3．0％、检出限分别为8．70和10．8μg/L。该法对实际水样加标回收率在94．5％～104．3％之间。     

Determination of selenium using atomically imprinted polymer (AIP) and hydride generation atomic absorption spectrometry

This paper describes selenium determination based on Se⁰ preconcentration in the imprinted polymer (synthesized with 2.25 mmol SeO₂, 4-vinylpyridine and 1-vinylimidazole) with subsequent detection on-line in HG-FAAS. During the synthesis, SeO₂ is reduced to Se (0). Therefore, there are no MIP neither IIP in the present work, thus we denominated: AIP, i.e., atomically imprinted polymers. For the optimization of analytical parameters Doehlert design was used. The method presented limit of detection and limit of quantification of 53 and 177 ng L⁻¹, respectively, and linear range from 0.17 up to 6 μg L⁻¹ (r = 0.9936). The preconcentration factor (PF), consumptive index (CI) and concentration efficiency (CE) were 232; 0.06 mL and 58 min⁻¹ respectively. The proposed method was successfully applied to determine Se in Brazil nuts (0.33 ± 0.03 mg kg⁻¹), apricot (0.46 ± 0.02 mg kg⁻¹), white bean (0.47 ± 0.03 mg kg⁻¹), rice flour (0.47 ± 0.02 mg kg⁻¹) and milk powder (0.22 ± 0.01 mg kg⁻¹) samples. It was possible to do 12 analyzes per hour. Accuracy was checked and confirmed by analyzing certified reference material (DORM-2, dogfish muscle), and samples precision was satisfactory with RSD lower than 10%.     

Determination of iron and copper in food samples by flow injection cloud point extraction flame atomic absorption spectrometry

In this study, flow injection-cloud point extraction (FI-CPE) of iron and copper in food samples by flame atomic absorption spectrometric determination was described. Triton X-114 non-ionic surfactant and Eriochrome Cyanine R (ECR) have been used as an extraction medium and a chelating agent, respectively. The amounts of Triton X-114, ECR and the pH value necessary for extraction were carefully optimized. In addition, several parameters of the FI-CPE system, including sample loading rate, column dimension, type of packing material, eluent flow rate were investigated and analytical characteristics of the method were evaluated. Under optimum conditions, detection limits of 0.33 ng/mL and 0.57 ng/mL and quantification limits of 1.1 ng/mL and 1.9 ng/mL for iron and copper along with enrichment factors of 141 and 99 were obtained, respectively. The calibration was linear over the range 1.5-25 ng/mL and 1.0-35 ng/mL for iron and copper, respectively. The proposed CPE technique has been successfully applied for the determination of iron and copper ions in certified reference materials (NCS DC 73349—bush, branches and leaves; and TM-23.2—fortified water), water samples (mineral and sea water) and food samples (vegetables, bread and hazelnut) with high efficiency.     

An ion-exchange method for speciation of antimony by flow injection electrothermal atomic absorption spectrometry

In this work, a simple preconcentration system, achieved by replacing the sample tip of the autosampler arm by a micro-column packed with Amberlite IRA-910 or silica gel chelating resin functionalised with 1,5-bis(di-2-pyridyl)methylene tbiocarbohydrazide (DPTH-gel), is developed for the determination of Sb(V) and total antimony, respectively. Different factors including pH of sample solution, ionic strength, concentration and volume of eluent, sample flow rate, sample loading time and matrix effects for preconcentration were investigated. The method has been applied to the determination of antimony species in different samples.     

Surfactant/oil/water system for the determination of selenium in eggs by graphite furnace atomic absorption spectrometry

An oil-in-water formulation has been optimized to determine trace levels of selenium in whole hen eggs by graphite furnace atomic absorption spectrometry. This method is simpler and requires fewer reagents when compared with other sample pre-treatment procedures. Graphite furnace atomic absorption spectrometric (GF AAS) measurement was carried out using standard addition calibration and Pd as a modifier. The precision, expressed as relative standard deviation, was better than 5% and the limit of detection was 1 µg L^− 1. The validation of the method was performed against a standard reference material Whole Egg Powder (RM 8415), and the measured Se corresponded to 95.2% of the certified value. The method was used for the determination of the Se level in eggs from hens treated with Se dietary supplements. Inorganic and organic Se sources were added to hen feed. The Se content of eggs was higher when hens were fed with organic Se compared to the other treatments. The proposed method, including sample emulsification for subsequent Se determination by GF AAS has proved to be sensitive, reproducible, simple and economical.