High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba0.5Sr0.5Zn0.2Fe0.8O3−δ perovskite cathode

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte based PCMFCs with stable Ba_0.5Sr_0.5Zn_0.2Fe_0.8O_3−δ (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 μm in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm⁻², and a low polarization resistance of the electrodes of 0.08 Ω cm² was achieved at 700 °C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells.     

Synthesis of nano-sized crystalline oxide ion conducting fluorite-type Y2O3-doped CeO2 using perovskite-like BaCe0.9Y0.1O2.95 (BCY) and study of CO2 capture properties of BCY

Formation of nano-sized Y₂O₃-doped CeO₂ (YCO) was observed in the chemical reaction between proton conducting Y₂O₃-doped BaCeO₃ (BCY) and CO₂ in the temperature range 700-1000 °C, which is generally prepared by wet-chemical methods that include sol-gel, hydrothermal, polymerization, combustion, and precipitation reactions. BCY can capture CO₂ of 0.13 g per ceramic gram at 700 °C, which is comparable to that of the well-known Li₂ZrO₃ (0.15 g per ceramic gram at 600 °C). Powder X-ray diffraction (PXRD), energy dispersive X-ray analysis (EDX), laser particle size analysis (LPSA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and ac impedance spectroscopy were employed to characterize the reaction product obtained from reaction between BCY and CO₂ and subsequent acid washing. PXRD study reveals presence of fluorite-like CeO₂ (a=5.410 (1) Å) structure and BaCO₃ in reaction products. TEM investigation of the acid washed product showed the formation of nano-sized material with particle sizes of about 50 nm. The electrical conductivity of acid washed product (YCO) in air was found to be about an order higher than the undoped CeO₂ reported in the literature.     

Mechanosynthesis of nanopowders of the proton-conducting electrolyte material Ba(Zr, Y)O3−δ

The formation of perovskite nanopowders of the common proton-conducting, electrolyte material Ba(Zr_1−xY_x)O_3−δ is demonstrated by room temperature mechanosynthesis for the compositional range x=0, 0.058 and 0.148. This is achieved with a planetary ball mill at 650 rpm in zirconia vials, starting from BaO₂ with ZrO₂, (ZrO₂)_0.97(Y₂O₃)_0.03 or (ZrO₂)_0.92(Y₂O₃)_0.08 precursors, respectively. Powder X-ray diffraction (XRD) reveals the formation of the perovskite phase in the early stages of milling with phase purity being achieved after milling times of 240 min for composition x=0.058 whereas 420 min is necessary for composition x=0.148. In contrast, traces of ZrO₂ are apparent in composition x=0 even after milling times of 420 min. The use of BaCO₃ as precursor does not allow the formation of the perovskite phase for any composition. The perovskite crystallites are spherical in shape with an average size determined from XRD of ca. 30 nm in agreement with transmission electron microscopy observations. FTIR spectra demonstrate that contamination levels of BaCO₃ in the mechanosynthesized powders are very low. The spherical shape and nanoscale of the crystallites allow densification levels that are highly competitive when compared to BaZrO₃-based materials formed by alternative synthesis techniques documented in the literature.     

Ba0.95Ce0.90Y0.10O3-α固体电解质的质子导电性

本文通过高温固相反应合成了Ba_0.95Ce_0.90Y_0.10O_3-α固体电解质,测定了该固体电解质高温(600～1000℃)下的氢的电化学透过(氢气泵)速度。结果表明,该固体电解质在本实验条件下具有良好的质子导电性,其质子迁移数为0.8～1,在600～700℃的较低温度下,几乎显示纯粹的质子导电性。     

Structure Evolution Process of Ce0.65Zr0.25Y0.1O1.95 Prepared by Oxidation-Coprecipitation Method

Ce_0.65Zr_0.25Y_0.1O_1.95 oxides were prepared by oxidation-coprecipitation method using ammonia and salvolatile as precipitators. The as-prepared samples were thermally treated at different temperatures and characterized by thermogravimetry-differential scanning calorimetry (TG-DSC), Fourier transform-infrared (FT-IR) spectrometry, X-ray diffraction (XRD), and specific surface area measurements (BET). The results showed that the hydroxyl and carboxyl groups coexisted in the precipitate and a perfect solid solution was gradually formed with an increase in calcination temperature. The physisorbed water was lost from 100 to 170 °C, hydroxyl groups were removed from 250 to 300 °C, and the carboxyl groups were eliminated from 420 to 500 °C. A structure model was further proposed to understand the Ce_0.65Zr_0.25Y_0.1O_1.95 structure evolution process in depth.     

BaCe0.8Y0.2O3-α固体电解质的离子导电性及其燃料电池性能

用高温固相反应合成了BaCe08Y02O3-α固体电解质,用氢浓差电池和氧浓差电池方法研究了它的离子导电特性.以该氧化物为固体电解质,多孔性Pt为电极材料,组成氢-空气燃料电池,测定了该燃料电池的电流-电压特性.研究发现,BaCe0.8Y0.2O3-α在氢气中几乎是一个纯的质子导体,在氧气中是一个氧离子和电子空穴的混合导体,其燃料电池的开路电压(OCV)接近于理论值,最大输出电流密度约为820mA@cm-2(1000℃),最大输出功率密度约为200mW@cm-2(1000℃),放电性能稳定,具有良好的电池性能.     

Preparation and hydrogen permeation of SrCe0.95Y0.05O3−δ asymmetrical membranes

Asymmetrical thin membranes of SrCe_0.95Y_0.05O_3−δ (SCY) were prepared by a conventional and cost-effective dry pressing method. The substrate consisted of SCY, NiO and soluble starch (SS), and the top layer was the SCY. NiO was used as a pore former and soluble starch was used to control the shrinkage of the substrate to match that of the top layer. Crack-free asymmetrical thin membranes with thicknesses of about 50 μm and grain sizes of 5–10 μm were successfully pressed on to the substrates. Hydrogen permeation fluxes (J_H2) of these thin membranes were measured under different operating conditions. At 950 °C, J_H2 of the 50 μm SCY asymmetrical membrane towards a mixture of 80% H₂/He was as high as 7.6 × 10⁻⁸ mol/cm² s, which was about 7 times higher than that of the symmetrical membranes with a thickness of about 620 μm. The hydrogen permeation properties of SCY asymmetrical membranes were investigated and activation energies for hydrogen permeation fluxes were calculated. The slope of the relationship between the hydrogen permeation fluxes and the thickness of the membranes was −0.72, indicating that permeation in SCY asymmetric membranes was controlled by both bulk diffusion and surface reaction in the range investigated.     

Sr2NiMoO6−δ as anode material for LaGaO3-based solid oxide fuel cell

The double-perovskite Sr₂NiMoO_6−δ (SNMO) was investigated as an anode material of a solid oxide fuel cell (SOFC). With a 300 μm thick La_0.9Sr_0.1Ga_0.8Mg_0.2O_3−σ (LSGM) disk as electrolyte and Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ as the cathode, the SNMO anode showed power densities of 819 mW cm⁻² in hydrogen at 1123 K. Moreover, there was no buffer layer between anode and electrolyte, which would reduce design techniques and save design cost. After test no chemical reaction was discovered between anode and electrolyte. The anode exhibited good conductivity and the value was around 60 S cm⁻¹ in H₂. Also it had almost linear thermal expansion from room temperature to 1253 K and the average thermal expansion coefficient was about 12.14 × 10⁻⁶ K⁻¹, which was quite close to that of La_0.9Sr_0.lGa_0.8Mg_0.2O₃ (12.17 × 10⁻⁶ K⁻¹) electrolyte.     

Synthesis and structural study of a new NASICON-type solid solution: Li1−xLax/3Zr2(PO4)3

A new complete solid solution of NASICON-type compounds between LiZr₂(PO₄)₃ and La_1/3Zr₂(PO₄)₃ was evidenced with the general formula Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1). These phases were synthesized by a complex polymerizable method and structurally characterized from Rietveld treatment of their X-ray and neutron powder diffraction data. This solid solution results from the substitution mechanism Li⁺→1/3La³⁺+2/3□ leading to an increase of the vacancies number correlated to an increase of the La content. According to this substitution mechanism, the general formula can then be written Li_1−xLa_x/3□_2x/3Zr₂(PO₄)₃ (0?x?1) in order to underline the correlation between the La content and the vacancies rate. For all the compounds, the structure is clearly related to that of the NASICON family with three crystallographic domains evidenced. For 0?x?0.5, all the members adopt at high temperature the typical NASICON-type structure (s.g. R3¯c), while at lower temperature, their structure distorts to a triclinic form (s.g. C 1¯), as observed for LiZr₂(PO₄)₃ prepared above 1100 °C. Moreover, in this domain, the reversible transition is clearly soft and the transition temperature strongly depends of the x value. For 0.6?x?0.9, the compounds crystallize in a rhombohedral cell (s.g. R3¯), while for x=1, the phase La_1/3Zr₂(PO₄)₃ is obtained (s.g. P3¯, Z=6, a=8.7378(2) Å, c=23.2156(7) Å).This paper is devoted to the structure analysis of the series Li_1−xLa_x/3Zr₂(PO₄)₃ (0?x?1), from X-ray and neutron powder thermo diffraction and transmission electron microscopy (TEM) studies.     

Orthorhombic–orthorhombic phase transitions in Nd2NiO4+δ (0.067≤δ≤0.224)

Variation of the phases of Nd₂NiO_4+δ with the excess oxygen concentration δ has been examined at room temperature in the range 0.067≤δ≤0.224 using the X-ray powder diffraction technique. The phases observed at room temperature are orthorhombic-I (0.21<δ≤0.224), orthorhombic-IV (0.175<δ≤0.21), orthorhombic-II (0.15<δ≤0.175), orthorhombic-II+quasi-tetragonal-I (0.10<δ≤0.15), and quasi-tetragonal-I (0.067<δ≤0.10).     

Doping studies of the magnetic cobaltocuprate CoSr2Y2−xCexCu2O9±δ

A structural, magnetic and electronic study of the cobaltocuprate CoSr₂Y_2−xCe_xCu₂O_9±δ (x=0.5-0.8) has been performed. All materials crystallise in the orthorhombic Cmcm symmetry space group in which chains of corner linked CoO₄ tetrahedra run parallel to the 1 1 0 direction. An antiferromagnetic transition is observed for x=0.5-0.8; T_M increases with x. A change in the dimensionality of the magnetic order occurs at x=0.8 as the interchain distance increases to a critical value. There is charge transfer between the cuprate planes and cobaltate layer as Ce doping increases, so that Co³⁺ is partially oxidised to Co⁴⁺ with a concomitant reduction in the valence of Cu. Superconductivity is not observed in any of the samples and a crossover from Mott to Efros and Shklovskii variable range hopping behaviour is evidenced as x increases from 0.5 to 0.8.     

Synthesis, thermal stability and magnetic properties of the Lu1−xLaxMn2O5 solid solution

Polycrystalline samples of the Lu_1−xLa_xMn₂O₅ solid solution system were synthesized under moderate conditions for compositions with x up to 0.815. Due to the large difference in ionic size between Lu³⁺ and La³⁺, significant changes in lattice parameters and severe lattice strains are present in the solid solution. This in turn leads to the composition dependent thermal stability and magnetic properties. It is found that the solid solution samples with x≤0.487 decompose at a single well defined temperature, while those with x≥0.634 decompose over a temperature range with the formation of intermediate phases. For the samples with x≤0.487, the primary magnetic transition occurs below 40 K, similar to LuMn₂O₅ and other individual RMn₂O₅ (R=Bi, Y, and rare earth) compounds. In contrast, a magnetic phase with a 200 K onset transition temperature is dominant in the samples with x≥0.634.     

Synthesis and ac susceptibility of YCa2Cu3O7−δ

The bulk superconducting YCa₂Cu₃O_7−δ compounds are prepared at an ordinary pressure of oxygen by conventional solid-state reaction method. The formation of sample is tested by means of XRD and is studied for their ac susceptibility below room temperature up to 77.5 K. The samples are found single-phase orthorhombic structure and found superconducting at 83.5 K. It is shown that the analysis is consistent with published data on YBa₂Cu₃O_7−δ oxide superconductor.     

固-溶法制备中温固体氧化物燃料电池高性能La0.8Sr0.2MnO3-Ba0.5Sr0.5Co0.8Fe0.2O3阴极

研究了新型固溶法合成La_0.8Sr_0.2MnO₃（LSM）包覆Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃（BSCF）复合粉体（LSM-BSCF）,并探讨了其作为中温固体氧化物燃料电池阴极材料的电化学性能。LSM-BSCF阴极结合了LSM和BSCF阴极的优点,不仅增大了三相界面,而且稳定了微观结构。当温度为600-750℃时,其极化阻抗为0.61-0.09 Ω·cm²。与溶液注入法制备的高性能电极相比,极大地提高了性能稳定性。     

High performance anode-supported intermediate temperature solid oxide fuel cells (IT-SOFCs) with La0.8Sr0.2Ga0.8Mg0.2O3−δ electrolyte films prepared by electrophoretic deposition

Remarkable power density was obtained for anode-supported solid oxide fuel cells (SOFCs) based on La_0.8Sr_0.2Ga_0.8Mg_0.2O_3−δ (LSGM) electrolyte films, fabricated following an original procedure that allowed avoiding undesired reactions between LSGM and electrode materials, especially Ni. Electrophoretic deposition (EPD) was used for the fabrication of 30 μm-thick electrolyte films. Anode supports were made of La_0.4Ce_0.6O_2−x (LDC). The LSGM powder was deposited by EPD on an LDC green tape-cast membrane added with carbon powder, both as pore former and substrate conductivity booster. A subsequent co-firing step at 1490 °C produced dense electrolyte films on porous LDC skeletons. Then, a La_0.8Sr_0.2Fe_0.8Co_0.2O_3−δ (LSFC) cathode was applied by slurry-coating and calcined at 1100 °C. Finally, the porous LDC layer was impregnated with molten Ni nitrate to obtain, after calcination at 900 °C, a composite NiO–LDC anode. Maximum power densities of 780, 450, 275, 175, and 100 mW/cm² at 700, 650, 600, 550, and 500 °C, respectively, were obtained using H₂ as fuel and air as oxidant, demonstrating the success of the processing strategy. As a comparison, electrolyte-supported SOFCs made of the same materials were tested, showing a maximum power density of 150 mW/cm² at 700 °C, more than 5 times smaller than the anode-supported counterpart.     

Composition dependence of the photophysical and photocatalytic properties of (AgNbO3)1−x(NaNbO3)x solid solutions

A series of orthorhombic photocatalysts (AgNbO₃)_1−x(NaNbO₃)_x solid solutions have been synthesized by a solid-state reaction method. The composition dependence of the photophysical and photocatalytic properties of synthesized solid solutions has been investigated systematically. With an increase in the content of NaNbO₃, we found that (1) the lattice parameters decreased; (2) the Nb-O bond length in NbO₆ octahedron reduced; (3) the band gap increased; and (4) the mean particle size decreased while the Brunauer-Emmett-Teller (BET) surface area increased. Photocatalytic activities of the (AgNbO₃)_1−x(NaNbO₃)_x (0?x?0.5) samples were evaluated from gaseous 2-propanol (IPA) decomposition into acetone and CO₂ under visible-light irradiation emitted from blue-light-emitting diodes (BLEDs; light intensity: 0.01 mW cm⁻²). Among all the samples, the (AgNbO₃)_0.6(NaNbO₃)_0.4 sample showed the highest photocatalytic activity.     

La0.6Sr1.4MnO4 layered perovskite anode material for intermediate temperature solid oxide fuel cells

La_0.6Sr_1.4MnO₄ (LSMO₄) layered perovskite with K₂NiF₄ structure was prepared and evaluated as anode material for La_0.8Sr_0.2Ga_0.83Mg_0.17O_3 − δ (LSGM) electrolyte supported intermediate temperature solid oxide fuel cells (IT-SOFCs). X-ray diffraction results show that LSMO₄ is redox stability. Thermal expansion coefficient of LSMO₄ is close to that of LSGM electrolyte. By adopting LSMO₄ as anode and La_0.6Sr_0.4Co_0.8Fe_0.2O₃ (LSCF) as cathode, maxium power densities of 146.6, 110.9 mW cm^− 2 with H₂ fuel at 850, 800 °C and 47.3 mW cm^− 2 with CH₄ fuel at 800 °C were obtained, respectively. Further, the cell demonstrated a reasonably stable performance under 180 mA cm^− 2 for over 40 h with H₂ fuel at 800 °C.     

Positron lifetime study of Pr1−xCaxMnO3 (x=0.5, 0.3) during magnetic transition

We measured the positron lifetime in perovskite manganites Pr_1−xCa_xMnO₃ (x=0.3, 0.5). Two lifetime components were observed for each compound; they were attributed to the annihilation of free positrons and positrons trapped at the A-site vacancies. The positron lifetime at the A-site vacancies changed significantly during the antiferromagnetic transition in both the compounds, whereas it was constant around the charge-ordering transition. This change indicates that the electron distribution at the vacancies changed possibly due to the change in the electron distribution of neighboring oxygen atoms. This result indicates that positron lifetime measurements can provide unique information on electronic states during a spin-related phase transition in various oxide materials.     

Thermoelectric properties of Cu-doped n-type (Bi2Te3)0.9–(Bi2−xCuxSe3)0.1(x=0–0.2) alloys

n-Type (Bi₂Te₃)_0.9–(Bi_2−xCu_xSe₃)_0.1 (x=0–0.2) alloys with Cu substitution for Bi were prepared by spark plasma-sintering technique and their structural and thermoelectric properties were evaluated. Rietveld analysis reveals that approximate 9.0% of Bi atomic sites are occupied by Cu atoms and less than 4.0 wt% second phase Cu_2.86Te₂ precipitated in the Cu-doped parent alloys. Measurements show that an introduction of a small amount of Cu (x0.1) can reduce the lattice thermal conductivity (κ_L), and improve the electrical conductivity and Seebeck coefficient. An optimal dimensionless figure of merit (ZT) value of 0.98 is obtained for x=0.1 at 417 K, which is obviously higher than those of Cu-free Bi₂Se_0.3Te_2.7 (ZT=0.66) and Ag-doped alloys (ZT=0.86) prepared by the same technologies.     

Fabrication and characterization of γ-Al2O3–clay composite ultrafiltration membrane for the separation of electrolytes from its aqueous solution

In this paper, we have reported the preparation of low cost γ-Al₂O₃ membrane on a macroporous clay support by dip-coating method. For the synthesis of γ-Al₂O₃ top layer on the support, a stable boehmite sol is prepared using aluminium chloride salt as a starting material by sol–gel route. The structural properties of the composite membrane as well as γ-Al₂O₃ powder is carried out using scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption–desorption isotherm data, Fourier transform infrared analysis (FTIR) and dynamic light scattering (DLS) analysis. The mean particle size of the boehmite sol used for coating is found to be 30.9 nm. The pore size distribution of the γ-Al₂O₃–clay composite membrane is found to be in the range of 5.4–13.6 nm. Separation performance of the membrane in terms of flux and rejection of single salts solution such as MgCl₂ and AlCl₃ as a function of pH, salt concentration and applied pressure is also studied. The rejection and flux behavior are found to be strongly dependent on electrostatic interaction between the charged molecules and γ-Al₂O₃–clay composite membrane. The intrinsic rejection has been determined by calculating the concentration at membrane surface (C_m) using Speigler–Kedem model. It is found that the observed rejection shows anomalous trend with increase in applied pressure and the intrinsic rejection increases with increase in applied pressure, a trend typical of the separation of electrolyte through charged membranes. At acidic pH, both the salt solution shows higher rejection. With increase in the salt concentration, observed rejection of salt decreases due to the enhanced concentration polarization. The maximum rejection of MgCl₂ and AlCl₃ is found to be 72% and 88%, respectively for salt concentration of 3000 ppm.