Characteristics of High In-Content InGaN Alloys Grown by MOCVD

InN and In0.46 Ca0.54N films are grown on sapphire with a CaN buffer by metalorganic chemical vapour deposition （MOCVD）. Both high resolution x-ray diffraction and high resolution transmission electron microscopy results reveal that these films have a hexagonal structure of single crystal. The thin InN film has a high mobility of 4 75 cm^2V^-1s^-1 and that oflno.46 Gao.54N is 163 cm^2 V^-1s^-1. Room-temperat ure photoluminescence measurement of the InN film shows a peak at 0.72eV, confirming that a high quality InN film is fabricated for applications to full spectrum solar cells.     

Quasi-monocrystalline silicon for thin-film devices

Thermal crystallization of a double layer porous Si film creates a monocrystalline Si film with a thin separation layer between the Si film and the reusable starting wafer. The process enables transfer of thin monocrystalline Si films to foreign substrates, whereby devices may be formed before or after separation of the film. Sub-micrometer thick films are almost compact, while films with a thickness of several μm contain voids, and are therefore termed “quasi-monocrystalline”. Internal voids strongly enhance optical absorption by light scattering. The hole mobility is 78 cm² V^-1 s^-1 at a p-type starting wafer resistivity of 0.05 Ω cm. Received: 24 March 1999 / Accepted: 29 March 1999 / Published online: 5 May 1999     

Transparent conducting antimony-doped tin oxide films deposited on flexible substrates by r.f. magnetron-sputtering

Transparent conducting antimony-doped tin oxide (SnO₂:Sb) films were deposited on organic substrates by r.f. magnetron-sputtering. Polycrystalline films with a resistivity of ≈ 6.5×10^-3 Ω cm, a carrier concentration of≈ 1.2×10²⁰ cm^-3 and a Hall mobility of ≈ 9.7 cm² v^-1 s^-1 were obtained. The average transmittance of these films reached 85% in the wavelength range of the visible spectrum. Received: 20 April 2001 / Accepted: 23 July 2001 / Published online: 17 October 2001     

Characterization of GaN/AlGaN epitaxial layers grown by metalorganic chemical vapour deposition for high electron mobility transistor applications

GaN and AlGaN epitaxial layers are grown by a metalorganic chemical vapour deposition (MOCVD) system. The crystalline quality of these epitaxially grown layers is studied by different characterization techniques. PL measurements indicate band edge emission peak at 363.8 nm and 312 nm for GaN and AlGaN layers respectively. High resolution XRD (HRXRD) peaks show FWHM of 272 and 296 arcsec for the (0 0 0 2) plane of GaN and GaN in GaN/AlGaN respectively. For GaN buffer layer, the Hall mobility is 346 cm²/V-s and carrier concentration is 4.5 × 10¹⁶/cm³. AFM studies on GaN buffer layer show a dislocation density of 2 × 10⁸/cm² by wet etching in hot phosphoric acid. The refractive indices of GaN buffer layer on sapphire at 633 nm are 2.3544 and 2.1515 for TE and TM modes respectively.     

A change in the electro-physical properties of narrow-band CdHgTe solid solutions acted upon by a volume discharge induced by an avalanche electron beam in the air at atmospheric pressure

The effect of a nanosecond volume discharge forming in an inhomogeneous electrical field at atmospheric pressure on the CdHgTe (MCT) epitaxial films of the p-type conduction with the hole concentration 2·10¹⁶ cm³ and mobility 500 cm²·V^–1·s^–1 is studied. The measurement of the electrophysical parameters of the MCT specimens upon irradiation shows that a layer exhibiting the n-type conduction is formed in the near-surface region of the epitaxial films. After 600 pulses and more, the thickness and the parameters of the layer are such that the measured field dependence of the Hall coefficient corresponds to the material of the n-type conduction. Analysis of the preliminary results reveals that the foregoing nanosecond volume discharge in the air at atmospheric pressure is promising for modification of electro-physical MCT properties.     

Influence of AlN interfacial layer on electrical properties of high-Al-content Al0.45Ga0.55N/GaN HEMT structure

Unintentionally doped high-Al-content Al_0.45Ga_0.55N/GaN high electron mobility transistor (HEMT) structures with and without AlN interfacial layer were grown by metal-organic chemical vapor deposition (MOCVD) on two-inch sapphire substrates. The effects of AlN interfacial layer on the electrical properties were investigated. At 300 K, high two-dimensional electron gas (2DEG) density of 1.66 × 10¹³ cm⁻² and high electron mobility of 1346 cm² V⁻¹ s⁻¹ were obtained for the high Al content HEMT structure with a 1 nm AlN interfacial layer, consistent with the low average sheet resistance of 287 Ω/sq. The comparison of HEMT wafers with and without AlN interfacial layer shows that high Al content AlGaN/AlN/GaN heterostructures are potential in improving the electrical properties of HEMT structures and the device performances.     

Pulsed laser deposition of Zr–N codoped <Emphasis Type="Italic">p</Emphasis>-type ZnO thin films

Present p-type ZnO films tend to exhibit high resistivity and low carrier concentration, and they revert to their natural n-type state within days after deposition. One approach to grow higher quality p-type ZnO is by codoping the ZnO during growth. This article describes recent results from the growth and characterization of Zr–N codoped p-type ZnO thin films by pulsed laser deposition (PLD) on (0001) sapphire substrates. For this work, both N-doped and Zr–N codoped p-type ZnO films were grown for comparison purposes at substrate temperatures ranging between 400 to 700 °C and N₂O background pressures between 10⁻⁵ to 10⁻² Torr. The carrier type and conduction were found to be very sensitive to substrate temperature and N₂O deposition pressure. P-type conduction was observed for films grown at pressures between 10⁻³ to 10⁻² Torr. The Zr–N codoped ZnO films grown at 550 °C in 1×10⁻³ Torr of N₂O show p-type conduction behavior with a very low resistivity of 0.89 Ω-cm, a carrier concentration of 5.0×10¹⁸ cm⁻³, and a Hall mobility of 1.4 cm² V⁻¹ s⁻¹. The structure, morphology and optical properties were also evaluated for both N-doped and Zr–N codoped ZnO films.     

Pulsed laser deposition of high-quality ZnO films using a high temperature deposited ZnO buffer layer

High-quality ZnO film growth on sapphire was achieved by pulsed laser deposition using a high temperature deposited ZnO buffer layer. This high temperature deposited buffer layer remarkably improves crystallinity of subsequent films. In particular, the full width at half-maximum of X-ray diffraction ω-rocking curves for ZnO films grown with the buffer layer is 0.0076° (27.36 arcsec) and 0.1242° (447.12 arcsec) for the out-of-plane (002) and in-plane (102) reflections, respectively. In addition, ZnO films grown with this buffer layer showed a carrier mobility of 88 cm²/V s, which is three times higher than that realized for ZnO films grown without the buffer layer. The room temperature photoluminescence spectra showed strong band edge emission with little or no defect-related visible emission. PACS 78.55.Et; 81.05.Dz     

Effect of Ⅲ/Ⅴ Ratio of HT-AIN Buffer Layer on Polarity Selection and Electrical Quality of GaN Films Grown by Radio Frequency Molecular Beam Epitaxy

We investigate the effect of A/N ratio of the high temperature （HT） AIN buffer layer on polarity selection and electrical quality of GaN films grown by radio frequency molecular beam epitaxy. The results show that low Al/N ratio results in N-polarity GaN films and intermediate Al/N ratio leads to mixed-polarity GaN films with poor electrical quality. GaN films tend to grow with Ga polarity on Al-rich AIN buffer layers. GaN films with different polarities are confirmed by in-situ reflection high-energy electron diffraction during the growth process. Wet chemical etching, together with atomic force microscopy, also proves the polarity assignments. The optimum value for room-temperature Hall mobility of the Ga-polarity GaN film is 703cm^2/V.s, which is superior to the N-polarity and mixed-polarity GaN films.     

Growth of wurtzite GaN films on αAl2O3 substrates using light-radiation heating metal-organic chemical vapor deposition

Epitaxial growth of high-quality hexagonal GaN films on sapphire substrates using light-radiation heating metal-organic chemical vapor deposition (LRH-MOCVD) is first reported. The deposition temperature is 950 °C, about 100 °C lower than that in normal rf-heating MOCVD growth. The FWHM of GaN (0002) peak of the X-ray diffraction rocking curve is 8.7 arc  min. Photoluminescence spectrum of GaN film shows that there is a very strong band-edge emission and no “yellow-band” luminescence. Hall measurement indicates that the n-type background carrier concentration of GaN film is 1.7×10¹⁸ cm^-3 and the Hall mobility of it is 121.5 cm²/V s. It is suggested that the radiation of light in GaN growth enhances the dissociation of ammonia and decreases the disadvantages of the parasite reaction between trimethylgallium and ammonia. Received: 20 August 1998 / Accepted: 30 October 1998 / Published online: 10 March 1999     

Optical and electrical characterization of well-aligned ZnO rods electrodeposited on stainless steel foil

Aligned ZnO nanorods grown on polycrystalline substrates have promising optoelectronic applications. Novel samples with such structures were electrodeposited on stainless steel foil from a ZnCl₂ route. Well-aligned and free-standing hexagonal nanorods with 100-nm diameter and closely packed microrods with a diameter above 1 μm could be grown normal to the substrate. The optical transition energies (absorption and emission) of samples were determined by transmittance and photoluminescence spectroscopy. We report, for the first time, the fabrication of high-quality Ag Schottky diodes formed on the oxygen-treated (002) facets of electrodeposited microrods. Diodes with a large barrier height (1.2 eV), low saturation current density (1.3 pA/cm²) and high rectification factor (5×10⁶ at ± 3 V) were achieved. The concentration and mobility of free electrons in oxygen-treated microrods were measured as 1.4×10¹⁴ cm^-3 and 1.2 cm² V^-1 s^-1, respectively. PACS  81.15.Pq; 81.16.-c; 85.30.Kk; 81.05.Dz; 78.55.Et     

The growth temperatures dependence of optical and electrical properties of InN films

InN films grown on sapphire at different substrate temperatures from 550°C to 700°C by metalorganic chemical vapor deposition were investigated. The low-temperature GaN nucleation layer with high-temperature annealing (1100°C) was used as a buffer for main InN layer growth. X-ray diffraction and Raman scattering measurements reveal that the quality of InN films can be improved by increasing the growth temperature to 600°C. Further high substrate temperatures may promote the thermal decomposition of InN films and result in poor crystallinity and surface morphology. The photoluminescence and Hall measurements were employed to characterize the optical and electrical properties of InN films, which also indicates strong growth temperature dependence. The InN films grown at temperature of 600°C show not only a high mobility with low carrier concentration, but also a strong infrared emission band located around 0.7 eV. For a 600 nm thick InN film grown at 600°C, the Hall mobility achieves up to 938 cm²/Vs with electron concentration of 3.9 × 10¹⁸ cm⁻³. Supported by the National Basic Research Program of China (Grant No. 2006CB6049), the National Natural Science Foundation of China (Grant Nos. 6039072, 60476030 and 60421003), the Great Fund of the Ministry of Education of China (Grant No. 10416), the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20050284004), and the Natural Science Foundation of Jiangsu Province of China (Grant Nos. BK2005210 and BK2006126)     

SnO2 thin films grown by pulsed Nd:YAG laser deposition

SnO₂ thin films have been deposited on glass substrates by pulsed Nd:YAG laser at different oxygen pressures, and the effects of oxygen pressure on the physical properties of SnO₂ films have been investigated. The films were deposited at substrate temperature of 500°C in oxygen partial pressure between 5.0 and 125 mTorr. The thin films deposited between 5.0 to 50 mTorr showed evidence of diffraction peaks, but increasing the oxygen pressure up to 100 mTorr, three diffraction peaks (110), (101) and (211) were observed containing the SnO₂ tetragonal structure. The electrical resistivity was very sensitive to the oxygen pressure. At 100 mTorr the films showed electrical resistivity of 4×10⁻² Ω cm, free carrier density of 1.03×10¹⁹ cm⁻³, mobility of 10.26 cm² V⁻¹ s⁻¹ with average visible transmittance of ∼87%, and optical band gap of 3.6 eV.     

Nanocrystalline silicon thin-film transistors with 50-nm-thick deposited channel layer, 10 cm2V-1s-1 electron mobility and 108 on/off current ratio

Thin-film transistors were made using 50-nm-thick directly deposited nanocrystalline silicon channel layers. The transistors have a coplanar top gate structure. The nanocrystalline silicon was deposited from discharges in silane, hydrogen and silicon tetrafluoride. The transistors combine a high electron field effect mobility of ∼10 cm² V^-1s^-1 with a low ‘off’ current of ∼10^-14 A per μm of channel length and an ‘on’/‘off’ current ratio of ∼10⁸. This result shows that transistors made from directly deposited silicon can combine high mobility with low ‘off’ currents. Received: 28 May 2001 / Accepted: 30 May 2001 / Published online: 30 August 2001     

Development of sulphurized SnS thin film solar cells

Thin films of tin sulphide (SnS) have been grown by sulphurization of sputtered tin precursor layers in a closed chamber. The effect of sulphurization temperature (T_s) that varied in the range of 150–450 °C for a fixed sulphurization time of 120 min on SnS film was studied through various characterization techniques. X-ray photoelectron spectroscopy analysis demonstrated the transformation of metallic tin layers into SnS single phase for T_s between 300 °C and 350 °C. The X-ray diffraction measurements indicated that all the grown films had the (111) crystal plane as the preferred orientation and exhibited orthorhombic crystal structure. Raman analysis showed modes at 95 cm⁻¹, 189 cm⁻¹ and 218 cm⁻¹ are related to the A_g mode of SnS. AFM images revealed a granular change in the grain growth with the increase of T_s. The optical energy band gap values were estimated using the transmittance spectra and found to be varied from 1.2 eV to 1.6 eV with T_s. The Hall effect measurements showed that all the films were p-type conducting nature and the layers grown at 350 °C showed a low electrical resistivity of 64 Ω-cm, a net carrier concentration of 2 × 10¹⁶ cm⁻³ and mobility of 41 cm² V⁻¹ s⁻¹. With the use of sprayed Zn_0.76Mg_0.24O as a buffer layer and the sputtered ZnO:Al as window layer, the SnS based thin film solar cell was developed that showed a conversion efficiency of 2.02%.     

Preparation and characterization of transparent conducting Zn−Sn−O films deposited on organic substrates at low temperature

Transparent conducting Zn−Sn−O films were deposited on Polypropylene adipate thin-film substrates at low temperature by r. f. magnetron sputtering. The structural, electrical and optical properties of the deposited films were investigated. All the obtained films are of amorphous structure and have a very good adhesion to the substrates. The resistivity, carrier concentration and Hall mobility of the film are 1.3×10⁻² Ω·cm, 4.1×10¹⁹ cm⁻³ and 12.4 cm²· V⁻¹· s⁻¹, respectively. The transmittance of the film reaches 82%.     

Synthesis and characterization of Ag-doped p-type ZnO nanowires

P-type ZnO nanowires with silver (Ag) doping were synthesized via a chemical vapor deposition process. The incorporation of Ag was confirmed by selected-area energy-dispersive x-ray spectroscopy. The formation of acceptor states was demonstrated by temperature and excitation power-dependent photoluminescence measurements. Characterization of field-effect transistors using Ag-doped ZnO nanowires as channels showed p-type conductivity of the nanowires with a hole concentration of 4.9×10¹⁷ cm⁻³ and a carrier mobility of approximately 0.18 cm² V⁻¹ s⁻¹.     

AlGaN/GaN heterostructure grown on 1 -tilt sapphire substrate by MOCVD

AlGaN/GaN epitaxial layers were grown on 0^°-tilt and 1^°-tilt sapphire substrates by metalorganic chemical vapor deposition (MOCVD). With exactly the same growth conditions, it was found that dislocation density was smaller and crystal quality was better for the AlGaN/GaN epitaxial layers prepared on 1^°-tilt sapphire substrate. We also found that AlGaN/GaN epitaxial layers on 1^°-tilt sapphire substrate were grown with step growth mode while those on 0^°-tilt substrate were grown with two-dimensional island growth. From the temperature-dependent mobility, it was found that crystal quality of the AlGaN/GaN epitaxial layer prepared on 1^°-tilt sapphire substrate is better.     

Mobility and conductivity of ionic and bonded defects in hydrogen-bonded chains with nonlinear interactions

The proton conductivity and the mobility arising from motions of the ionic and bonded defects, in hydrogen-bonded molecular systems are investigated by means of the quantum mechanical method. Our two component model goes beyond the usual classical harmonic interaction by inclusion of a quartic interaction potential between the nearest-neighbor protons. Among the rich variety of soliton patterns obtained in this model, we focus our attention to compact kink (kinkon) solutions to calculate analytically, the mobility of the kinkon-antikinkon pair and the specific electrical-conductivity of the protons transfer in the hydrogen-bonded systems under an externally applied electrical-field through the dynamic equation of the kinkon-antikinkon pair. For ice, the mobility and the electrical conductivity of the proton transfer obtained are about 5.307×10^-7 m²  V^-1  s^-1 and 6.11×10^-4 Ω^-1 m^-1, respectively. The results obtained are in qualitative agreement with experimental data.     

Impact of ZnTe buffer on the electrical properties of n-type GaSb:Te films

We have investigated on the molecular beam epitaxy (MBE) of Te-doped GaSb films on ZnTe buffer. Te-doped GaSb (GaSb:Te) films with and without ZnTe buffer were grown on (0 0 1) GaAs substrates. GaSb:Te/ZnTe/GaAs film revealed higher mobility (=631 cm²/V s) in comparison to GaSb:Te/GaAs film (=249 cm²/V s). To explain the higher mobility of GaSb:Te on ZnTe buffer, dislocation density and temperature dependence of Hall measurement results were analyzed. Temperature dependence of Hall measurement shows strong influence of the dislocation scattering, which indicates that dislocation reduction by the ZnTe buffer enhances the carrier mobility of GaSb films.