一种疏水缔合水溶性聚合物的合成及其溶液性能

粘度;抗盐性;表面活性剂;一种疏水缔合水溶性聚合物的合成及其溶液性能     

疏水缔合水溶性聚合物P(DMDAAC-NVP-IOA)与萘普生相互作用及释药性

以水为介质,采用自由基胶束聚合制备了二甲基二烯丙基氯化铵(DMDAAC)、N-乙烯基吡咯烷酮(NVP)和丙烯酸异辛酯(IOA)三元共聚疏水缔合水溶性聚合物P(DMDAAC-NVP-IOA),测定了聚合物的聚电解质性质和疏水缔合性质.应用IR、XRD、DSC测试技术研究了各组分的相互作用.结果表明,所制备的P(DMDAAC-NVP-IOA)同时具有聚电解质和疏水缔合特性.随P(DMDAAC-NVP-IOA)量增加,IR分析中萘普生羧基的羰基伸缩振动峰1 684 cm-1处峰变宽、强度明显减弱;XRD分析中的12°～29°间衍射峰逐渐变宽、变小直至消失;DSC分析中只有1个转变曲线,P(DMDAAC-NVP-IOA)与萘普生之间存在分子级相互作用.在pH=7.4磷酸盐缓冲液中,疏水缔合水溶性聚合物具有药物缓释特性,可用扩散-溶解模型进行最佳拟合.     

孪尾疏水缔合三元共聚物的粘度行为:水解度的影响

以十二烷基硫酸钠(SDS)为表面活性剂,利用氧化还原体系、采用前加碱共聚-共水解的方法制备了孪尾疏水缔合水溶性三元共聚物聚(丙烯酰胺／丙烯酸钠／N,N-二己基丙烯酰胺)[P(AM/NaAA／DiC6AM)],研究了P(AM／NaAA／DiC6AM)稀溶液及亚浓溶液的性能。随理论水解度的增加,P(AM／NaAA／DiC6AM)水溶液的特性粘数[η]增加,Huggins常数KH减小。P(AM／NaAA／DiC6AM)水溶液的表现粘度随理论水解度的增加而增加,随温度、剪切速率的增加而降低,随剪切速率的增加开始时降低较快而后变化较小。P(AM／NaAA/DiC6AM)在盐溶液中随NaCl、CaCl2质量浓度的增加,出现盐增粘现象;理论水解度不同的P(AM／NaAA／DiC6AM)与SDS水溶液的表现粘度在wSDS=0．050～0．400g／L范围内随SDS质量浓度的变化差别不大。     

Influence of Hydrophobically Associating Polyacrylamide on Dispersion Property of Water-Soluble Phenol-For-maldehyde Resin

To improve dispersion stability of water soluble phenol-fomaldehyde resin (PFR) in relatively low salinity water, the effect of hydrophobically associating polymer (HAP) on the dispersion property of PFR in NaCl solution was studied by the measurement of the size and zeta potential of PFR, HAP, and PFR/HAP molecule aggregates in NaCl solution, and the turbidity of PFR and PFR/HAP dispersions. The results show that due to the hydrophobically group on HAP molecule has similar structure as molecular structure of PFR and stronger hydrophobically association of HAP molecules in NaCl solution, HAP, and PFR molecules can form complex molecule aggregates together. The formation of the complex molecule aggregates enhanced the stability of PFR dispersion in NaCl solution.     

Retention Behaviors of Hydrophobically Associating Polyacrylamide Prepared via Inverse Microemulsion Polymerization Through Porous Media

The retention behavior of hydrophobically associative polyacrylamide (HAPAM) with homogeneous composition in porous media was investigated. The results showed that HAPAM could exhibit different retention behavior, compared to PAM due to the existence of hydrophobic association group in HAPAM molecular frame. The critical association concentration could also be reflected by the curves between HAPAM concentration and retention amount. The retention amount of HAPAM was higher than that of polyacrylamide (PAM) and was smaller than the absorption amount of HAPAM. The retention mechanism was mainly controlled by adsorption mechanism.     

疏水缔合聚丙烯酰胺与双子表面活性剂的相互作用

制备了一种脂肪酸酯双磺酸盐型双子表面活性剂, 利用粘度法、界面张力法和原子力显微镜研究了疏水缔合聚丙烯酰胺与双子表面活性剂在溶液中的相互作用. 实验结果表明: 疏水缔合聚丙烯酰胺在溶液中能够通过自组装形成疏水微区并发展成网络结构, 疏水微区与表面活性剂在溶液中能形成混合胶束; 当一定量的表面活性剂加入时, 对疏水缔合聚丙烯酰胺的自组装起促进作用, 而过多双子表面活性剂的加入又会对聚合物分子的自组装起抑制作用, 从而显著影响疏水缔合聚丙烯酰胺的溶液性质, 随着表面活性剂浓度的增加, 聚合物溶液粘度先增加、再降低; 同时, 疏水缔合聚丙烯酰胺对双子表面活性剂的界面性能也有较大影响, 聚合物的加入使双子表面活性剂降低油/水界面张力的能力下降, 油/水界面张力达到平衡所需时间延长.     

疏水缔合聚丙烯酰胺与双子表面活性剂的自组装

通过荧光光谱、动/静态激光光散射研究了疏水缔合聚丙烯酰胺(HAPAM)自组装行为及双子表面活性剂(双十四酸乙二酯双磺酸盐(DMES-14))对其的影响.实验结果表明:聚合物HAPAM在溶液中能够通过自组装形成疏水微区,表现出芘的发射光谱中第一振动峰(373nm)与第三振动峰(383nm)的荧光强度之比(I1/I3)值随聚合物浓度的增大而下降,当聚合物HAPAM浓度(CP)达到一定值后,I1/I3值不再变化;当加入表面活性剂时,HAPAM能够与双子表面活性剂在溶液中形成混合胶束,在聚合物浓度一定时,I1/I3值随表面活性剂浓度(CS)的增大急速下降,当表面活性剂浓度达到30mg·L-1时,I1/I3值趋于恒定;当表面活性剂浓度一定时,聚合物/表面活性剂二元体系中聚集体的聚集数随HAPAM浓度的增大出现先下降再增加的过程;一定量的双子表面活性剂对HAPAM分子间的缔合起促进作用,过量的双子表面活性剂对HAPAM分子间的缔合起抑制作用,使HAPAM的表观重均分子量(Mw,a)、均方根回转半径()和流体力学半径()随表面活性剂浓度增加先增大后减小,而HAPAM的/比值则随表面活性剂浓度增大出现一定程度的上升,表明HAPAM分子链段变得相对舒展.     

P(AM-NVP-DMDA)疏水缔合水溶性共聚物的研究

采用自由基水溶液共聚合法制备了Ｐ（ＡＭ－ＮＶＰ－ＤＭＤＡ）疏水缔合水溶性共聚物。对共聚物的溶液性能进行了研究,包括盐效应、粘温关系、流变性能、热稳定性、与碱、表面活性剂的相互作用、稀溶液性质等。共聚物分子中由于引入了较多的疏水基团而具有较强的疏水缔合效应,在聚合物浓度较低时具有较高粘度。ＮＶＰ结构单元的引入可适当提高共聚物溶液的热稳定性。对共聚物溶液的电镜分析结果表明,在其水溶液中存在着微相分离结构,它对共聚物溶液的增粘起着重要作用。     

疏水缔合聚合物稳定乳状液的研究*

本文综述了近年来疏水缔合聚合物稳定乳状液的研究进展。论述了疏水缔合聚合物水溶液的性质,由于其较复杂的分子结构以及其分子主链上疏水基团的缔合作用,使其水溶液增稠的能力比小分子表面活性剂的增稠能力强的多。另外,对疏水缔合聚合物单独稳定乳状液的研究现状进行了介绍,其稳定乳状液的机理与小分子表面活性剂不同。同时讨论了疏水缔合聚合物与表面活性剂的相互作用,此类聚合物可与小分子表面活性剂通过静电和疏水缔合发生强烈的相互作用形成复合体系,并评述了其复配体系稳定乳状液的情况。最后总结了疏水缔合聚合物稳定乳状液的机理。     

Solution Association Characterization of Hydrophobically Associating Polyacrylamide Obtained from Produced Fluids

The hydrophobically associating polyacrylamide (HAPAM) obtained from produced fluids with compositional homogeneity was systematically investigated by zero-shear viscosity, fluorescence, sand-pipes experiment and adsorption behavior. The results showed that HAPAM obtained from produced solution through porous media has been possession in hydrophobic association character. The critical association concentration (CAC) determined by viscosity method, fluorescence spectroscopy method and micro-pore method have no obvious change compared with the original polymer. The hydrophobic associative capability of HAPAM obtained from produced fluids was smaller than that of original HAPAM. Compared to original PAM and PAM obtained from produced fluids, HAPAM obtained from produced fluids still exhibits promising applied potential. It reveals the possibility that HAPAM obtained from produced could be re-used for enhance oil recovery.     

疏水缔合聚丙烯酰胺在盐水中的自组装行为

使用静态光散射、动态光散射以及原子力显微镜(AFM)研究了疏水缔合聚丙烯酰胺(HAPAM)在盐水溶液中的自组装行为.研究了聚合物分子在不同盐浓度中的表观重均分子量(Mw,a),均方根回转半径(),流体力学半径(),第二维里系数(A2)的变化,并根据/的比值得出聚合物分子的聚集形态.实验结果表明:随着盐浓度的增强,聚合物溶液的分子链由舒展变得卷曲.     

疏水缔合水溶性聚合物AO的溶液粘度行为研究

研究了稀溶液中疏水链链长、无机电解质NaCl和CaCl2对疏水缔合水溶性丙烯酰胺／甲基丙烯酰氨乙基-二甲基烷基溴化铵／丙烯酸钠共聚物(AO)在水溶液中的特性粘数和Huggins常数的影响，以及聚合物AO-8的特性粘数和Huggins常数随温度的变化。结果表明：在稀溶液中，无机电解质离子强度增大，共聚物AO在NaCl和CaCl2溶液中的特性粘数减小，Huggins常数增大。在亚浓溶液范围对聚合物质量分数、温度、剪切速率及NaCl含量对聚合物的水溶液表现粘度的影响进行了研究，观察到疏水缔合聚合物盐水溶液在NaCl含量提高的情况下，出现的增粘现象。     

三次采油用疏水缔合型AM/DBA共聚物的研究

微乳液;耐温耐盐聚合物;三次采油用疏水缔合型AM/DBA共聚物的研究     

Hydrophobically Associating Polyacrylamides Prepared by Inverse Suspension Polymerization: Synthesis,Characterization and Aqueous Solution Properties

Hydrophobically associating polyacrylamides (HAPAMs) were synthesized via inverse suspension polymerization using ammonium persulphate (APS)/tertramethylethylenediamine (TEMED) as the redox initiators, 2-methacryloyloxyethyl n-alkyl dimethyl ammonium bromide (DM-n, n = 8, 12, 16) as the hydrophobic comonomers. The structures of the copolymers were elucidated by FT-IR and ionic chromatographic analysis, respectively. The morphology and particle size of the resultant HAPAMs were characterized by scanning electronic microscope (SEM) and laser particle size analyzer, which revealed that spherical particles were formed and the particle size exhibited Gaussian distribution centered from 25 μ m to 162 μ m. Furthermore, the solution properties of the copolymers were studied with viscometry and the results showed that HAPAMs synthesized under optimal conditions exhibited an obvious viscosity enhancement in aqueous solution and excellent salt-tolerant capability in brine.     

SET-LRP法制备星型疏水缔合水溶性聚合物

采用丙烯酰胺(AM)、2-丙烯酰胺基-2-甲基丙磺酸钠(NaAMPS)以及N-叔丁基丙烯酰胺(NtBA)为共聚单体,以Cu~0粉/三(2-二甲氨基乙基)胺(Me_6-TREN)为催化体系,四氯化碳(CCl_4)为引发剂,利用单电子转移自由基聚合(SET-LRP)方法合成星型疏水缔合水溶性聚合物P(AM/NtBA/NaAMPS)。采用控制变量法分别考察了引发温度、疏水单体含量、AMPS含量、引发剂用量、催化剂铜、单体浓度等因素对聚合物相对分子质量的影响,确定了最佳聚合条件并考察了聚合物的耐温抗盐性能。结果表明,当单体浓度为35%,引发温度为25℃,AM、AMPS、NtBA分别占单体总量的93.6%、5%、1.4%(摩尔比),引发剂质量分数为0.4942%,催化剂铜的质量分数为0.0848%,钝化剂的质量分数为0.1192%时,所得星型疏水缔合水溶性聚合物P(AM/NtBA/NaAMPS)的相对分子质量出现最高值为267万,同时具有一定的耐温抗盐性,其溶液性能与线型化的P(AM/NtBA/NaAMPS)相似,且在相同浓度下CaCl_2对聚合物表观粘度的影响比NaCl大。     

水溶性疏水缔合型聚(丙烯酰胺-丙烯酸十六酯)溶液性质的研究

采用沉淀聚合法制备水溶性的丙烯酰胺－丙烯酸十六疏水缔合型共聚物,研究了共聚物水溶液的性质及其影响因素。随着疏水基团含量增加,共聚物在纯水中及NaCl溶液中的特性粘数[η]均减小,疏水基团临界缔合浓度降低。共聚物溶液浓度高于监界缔合浓度时,溶液表现粘度急剧增加,表明溶液中分子间缔合大量形成。     

改性聚丙烯酰胺水溶液的疏水缔合性质

合成了一种疏水缔合水溶性聚丙烯酰胺共聚物,使用荧光光谱法并结合紫外及流变性实验,对制备的疏水缔合水溶性聚丙烯酰胺共聚物在水溶液中形成疏水微区、超分子聚集体及空间网络结构进行了研究,并用扫描电子显微镜证实了溶液中网络结构的存在.     

一种水溶性疏水缔合聚合物二临界缔合行为研究

对三元共聚疏水缔合聚合物（丙烯酰胺／十八烷基二甲基烯丙基氯化铵／苯乙烯）的临界缔合浓度进行研究,发现其具有二临界缔合现象以及其在二临界缔合浓度附近不同的耐温抗盐的流变行为。研究结果表明,该疏水缔合聚合物的第一临界缔合浓度（C1^＊）为500mg／L,第二临界缔合浓度（C2^＊）为2400mg／L;C2^＊附近聚合物溶液的耐温性能较差;抗盐性能表现出三种不同的情况：随着盐质量浓度的增加,C〈C1^＊时,溶液粘度下降;C1^＊〈C〈C2^＊时,溶液粘度先增加后下降;C〉C2^＊时,溶液粘度先快速增加,后缓慢增加,最后下降。     

荧光探针法研究疏水改性聚丙烯酰胺溶液的疏水缔合行为

采用胶束共聚 共水解方法合成疏水改性水溶性聚合物聚(丙烯酰胺/丙烯酸钠/N 辛基丙烯酰胺)[P(AM/NaAA/C8AM)],并以芘为荧光探针,应用稳态荧光光谱法研究了它的疏水缔合行为。结果表明,随聚合物浓度、疏水单体摩尔分数、疏水侧链长和温度的增加,疏水缔合作用增强;不同疏水单体含量的P(AM/NaAA/C8AM)的临界缔合浓度为1.5~3.0 g/L;表面活性剂十二烷基硫酸钠(SDS)与P(AM/NaAA/C8AM)发生了强烈的疏水相互作用,形成混合胶束,得到SDS的临界胶束浓度(CMC)为8×10-3 mol/L;由于聚合物链上羧基的存在,使其具有良好的 pH敏感性,随 pH值的增大,P(AM/NaAA/C8AM)的疏水缔合作用呈现先减弱后恒定再增强的变化。     

疏水缔合型水溶性高分子的合成与表征

本文综述了疏水缔合型水溶性高分子的合成与表征方法，６文中介绿了在合成过程中提高油溶性单体和水溶性单体的混溶性以及疏水基团均匀分布的方法，并了用核磁共振，上光谱等方法测定疏水物含量的方法。