Crystallization kinetics and morphology of poly(butylene succinate‐co‐adipate)

The crystallization kinetics of biodegradable poly(butylene succinate‐co‐adipate) (PBS/A) copolyester was investigated by using differential scanning calorimetry (DSC) and polarized optical microscopy (POM), respectively. The Avrami and Ozawa equations were used to analyze the isothermal and nonisothermal crystallization kinetics, respectively. By using wide‐angle X‐ray diffraction (WAXD), PBS/A was identified to have the same crystal structure with that of PBS. The spherulitic growth rates of PBS/A measured in isothermal conditions are very well comparable with those measured by nonisothermal procedures (cooling rates ranged from 0.5 to 15 °C/min). The kinetic data were examined with the Hoffman–Lauritzen nucleation theory. The observed spherulites of PBS/A with different shapes and textures strongly depend on the crystallization temperatures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3231–3241, 2005     

Morphology and thermal properties of poly(L‐lactide)/poly(butylene succinate‐co‐butylene adipate) compounded with twice functionalized clay

Poly(L ‐lactide) (PLLA)/poly(butylene succinate‐co‐butylene adipate) (PBSA) blends were compounded with Cloisite 25A® (C25A) and C25A functionalized with epoxy groups, respectively. Epoxy groups on the surface of C25A were introduced by treating C25A with (glycidoxypropyl)trimethoxy silane (GPS) to produce so called Twice Functionalized Organoclay (TFC). Variation of morphology and properties of PLLA/PBSA/C25A composites was investigated before and after the treatment with GPS. The morphological structure of the composites was analyzed by using X‐ray diffractometry (XRD) and transmission electron microscopy (TEM). The silicate layers of PLLA/PBSA/TFC were exfoliated to a larger extent than PLLA/PBSA/C25A. Incorporation of the epoxy groups on C25A improved significantly elongation at break as well as tensile modulus and tensile strength of PLLA/PBSA/C25A. The larger amount of exfoliation of the silicate layers in PLLA/PBSA/TFC as compared with that in PLLA/PBSA/C25A was attributed to the increased interfacial interaction between the polyesters and the clay due to chemical reaction. Thermo gravimetric analysis revealed that both T_5%, which was the temperature corresponding to 5% weight loss, and activation energy of thermal decomposition of PLLA/PBSA/TFC were far superior to those of PLLA/PBSA/C25A as well as to those of PLLA/PBSA, indicating that the composites with exfoliated silicate layers were more thermally stable than those with intercalated silicate layers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 478–487, 2005     

Thermal analysis of the multiple melting behavior of poly(butylene succinate‐co‐adipate)

The melting behavior of poly(butylene succinate‐co‐adipate) (PBSA) isothermally crystallized from the melt was investigated by differential scanning calorimetry. Triple, double, or single melting endotherms were observed in subsequent heating scan for the samples isothermally crystallized at different temperatures. These endothermic peaks were labeled as I, II, and III for low‐, middle‐, and high‐temperature melting endotherms, respectively. The independence of endotherm III to the crystallization temperature, the existence of an exothermic crystallization peak just below the endotherm III, and the heating rate dependence of endotherm III indicated that endotherm III was due to the remelting of recrystallized lamellar during a heating scan. The influence of crystallization time on the melting behavior of PBSA showed that endotherms II and III developed prior to endotherm I; endotherm III developed rather simultaneously with endotherm II. Further investigation showed that the peak temperature of endotherm I increased linearly with the logarithm of the crystallization time. It suggested that endotherm II was attributed to the melting of the primary lamellae, while endotherm I was due to the melting of secondary lamellae. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3077–3082, 2005     

Crystallization kinetics and morphology of biodegradable poly(butylene succinate‐co‐propylene succinate)s

The crystallization behavior of biodegradable poly(butylene succinate) and copolyesters poly(butylene succinate‐co‐propylene succinate)s (PBSPS) was investigated by using ¹H NMR, DSC and POM, respectively. Isothermal crystallization kinetics of the polyesters has been analyzed by the Avrami equation. The 2.2‐2.8 range of Avrami exponential n indicated that the crystallization mechanism was a heterogeneous nucleation with spherical growth geometry in the crystallization process of polyesters. Multiple melting peaks were observed during heating process after isothermal crystallization, and it could be explained by the melting and recrystallization model. PBSPS was identified to have the same crystal structure with that of PBS by using wide‐angle X‐ray diffraction (WAXD), suggesting that only BS unit crystallized while the PS unit was in an amorphous state. The crystal structure of polyesters was not affected by the crystallization temperatures, too. Besides the normal extinction crosses under the POM, the double‐banded extinction patterns with periodic distance along the radial direction were also observed in the spherulites of PBS and PBSPS. The morphology of spherulites strongly depended on the crystallization temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 420–428, 2007     

Nonisothermal crystallization behavior of poly(butylene adipate‐co‐terephthalate)/clay nano‐biocomposites

The study of the nonisothermal crystallization behavior of layered silicates micro‐ and nano‐biocomposites based on poly(butylene adipate‐co‐terephthalate) (PBAT), a biodegradable copolyester, has been carried out with different theoretical models. They were applied and developed with the aim to describe and better understand the influence of the layered silicates dispersion on crystallization. The nucleation efficiency of the layered silicates has been demonstrated with the use of the “Modified Avrami model,” thanks to the higher crystallization rate parameter, Z_c, and of the lower crystallization half‐time, t_1/2, compared to the neat matrix. The crystallization activation energies, E_a, calculated from “Kissinger's model” have shown that layered silicates have a negative effect on the crystallite growth process. Thus, these analyses have shown that layered silicates have a double effect on the crystallization process. These two opposites' phenomena depend on the dispersion quality and are more pronounced for the intercalated nano‐biocomposites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1503–1510, 2007     

Enhanced nonisothermal crystallization of a series of poly(butylene succinate‐co‐terephthalate) biopolyesters by poly(vinyl butyral)

Enhanced nonisothermal crystallization of a series of poly(butylene succinate‐co‐terephthalate) (PBST) by poly(vinyl butyral) (PVB) as a macromolecular nucleating agent has been examined systematically with various techniques and theoretical modeling. The role of PVB depends strongly on the butylene terephthalate content, PVB content, and cooling rate. The (0.3–0.7 wt %) PVB reduces the spherulitic size, but considerably increases the peak temperature of crystallization, for example, by 28 °C for the PBST with 50 mol % terephthalic acid. The effects of PVB are believed to stem from its unique molecular structure. Both the hydroxyl and butyral groups of PVB may synergistically participate in nucleating PBSTs for crystallization because of favorable secondary interaction and affinity of butyral groups with butylene succinate units of PBSTs. Only the Tobin model suffices to describe the nonisothermal crystallization kinetics, while the modified Avrami model is suitable for limited crystallinity. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 658–672     

Effects of comonomer sequential structure on thermal and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)s

In this work, new investigations on the effect of comonomer sequential structure on the thermal and crystallization behaviors and biodegradability have been implemented for the biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST) as well as aliphatic poly(butylene succinate) (PBS). At first, these copolyesters were efficiently synthesized from dimethyl succinate and/or dimethyl terephthalate and 1,4‐butanediol via condensation polymerization in bulk. Subsequently, their molecular weights and macromolecular chain structures were analyzed by gel permeation chromatography (GPC) and nuclear magnetic resonance (NMR) spectroscopy. By means of differential scanning calorimeter (DSC) and wide‐angle X‐ray diffractometer (WAXD), thermal and crystallization behaviors of these synthesized aromatic–aliphatic copolyesters were further explored. It was demonstrated that the synthesized copolyesters were revealed to have random comonomer sequential structures with thermal and crystallization properties strongly depending on their comonomer molar compositions, and that crystal lattice structures of the new crystallizable copolyesters shifted from the monoclinic crystal of semicrystalline PBS to triclinic lattice of the poly(butylene terephthalate) (PBT) with increasing the terephthalate comonomer composition, and the minor comonomer components were suggested to be trapped in the crystallizable component domains as defects. In addition, the enzymatic degradability was also characterized for the copolyesters film samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1635–1644, 2006     

Influence of biodegradation on crystallization of poly (butylene adipate‐co‐terephthalate)

The biodegradation of aromatic‐aliphatic biodegradable polyester poly (butylene adipate‐co‐terephthalate) (PBAT) was studied under mesophilic (37°C) and thermophilic (55°C) anaerobic conditions. Anaerobic sludge from municipal wastewater treatment plant was utilized as an inoculum. Non‐isothermal crystallization kinetics of PBAT before and after biodegradation was explored by differential scanning calorimetry. Under mesophilic anaerobic conditions (37°C), the biodegradation after 126 days was only 2.2%, molecular weight changed from 93 000 to 25 500 g/mol, and the crystallization behavior was changed only slightly. However, biodegradation under thermophilic anaerobic conditions (55°C) caused much bigger changes: biodegradation according to biogas production reached after 126 days 8.3%, molecular weight changed from 93 000 to 9430 g/mol, and the crystallization behavior was changed significantly. While T_m increased only slightly, T_c on the other hand increased significantly for the sample after biodegradation at 55°C. Also, the crystallization rate was slower (particularly at lower cooling rates), but crystallinity was slightly higher. The diffraction pattern was observed by X‐ray diffraction.     

Transesterification and crystallization behavior of poly(butylene succinate)/poly(butylene terephthalate) block copolymers

The block copolymers of poly(butylene succinate) (PBS) and poly(butylene terephthalate) (PBT) were synthesized by melt processing for different times. The sequence distribution, thermal properties, and crystallization behavior were investigated over a wide range of compositions. For PBS/PBT block copolymers it was confirmed by statistical analysis from ¹H-NMR data that the degree of randomness (B) was below 1. The melting peak (T_m) gradually moved to lower temperature with increasing melt processing time. It can be seen that the transesterification between PBS and PBT leads to a random copolymer. From the X-ray diffraction diagrams, only the crystal structure of PBS appeared in the M1 copolymer (PBS 80 wt %) and that of PBT appeared in the M3 (PBS 50 wt %) to M5 (PBS 20 wt %) copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 147–156, 1998     

Impact of cellulose nanocrystal aspect ratio on crystallization and reinforcement of poly(butylene adipate‐co‐terephthalate)

Cellulose nanocrystals (CNCs) are appealing nanomaterials for the reinforcement of polymeric materials. It is now well established that high mechanical properties are obtained when preparing the nanocomposite by casting/evaporation methods and using CNC contents above the percolation threshold. This phenomenon results from the formation of a stiff CNC network within the matrix meaning that the properties of the matrix play only a limited role on the mechanical properties of the material when the matrix is in the rubbery state. In subpercolation concentration or when using a different processing technique, the level of understanding is less clear, mainly when the CNC‐induced crystallization of the matrix interferes with the reinforcing mechanism. In this study, we used CNCs with different aspect ratios to prepare nanocomposites by extrusion with polybutyrate adipate terephthalate as matrix. The impact of CNC on the crystallinity of the matrix and mechanical properties of the nanocomposite has been investigated. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2284–2297     

Polylactide/poly(butylene adipate‐co‐terephthalate)/rare earth complexes as biodegradable light conversion agricultural films

Rare earth europium(III) complex with α‐thenoyltrifluoroacetone and triphenylphosphine oxide (Eu (TTA)₃(TPPO)₂, shortened as EuTT) was synthesized in this paper, then blended with polylactide (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) to prepare the biodegradable agricultural films. Through the optical performance, mechanical properties, and other research, the results showed that the rare earth complex could convert the sun's ultraviolet light to red light when doped polymer. Moreover, the relative intensity ratio of ⁵D₀/⁷F₂ to ⁵D₀/⁷F₁ of PLA/PBAT/EuTT film could reach 3.79, which implied that the film had strong fluorescence intensity and high color purity. The highest tensile strength of the film could reach 36.7/25.2 MPa, and the elongation at break was 462.8/483.0% in the machine and in the transverse direction when the added amount of Eu (TTA)₃(TPPO)₂ was 0.1 wt%. The tensile strength of the film was 33.3/20.1 MPa, and the elongation at break could reach 535.8/413.6% when the added amount of Eu (TTA)₃(TPPO)₂ was increased up to 0.3 wt%. Gel permeation chromatography showed that the Eu (TTA)₃(TPPO)₂ could cause depolymerization of polylactide, resulting in a decrease in the molecular weight of PLA. Furthermore, the crystallization ability of PLA was also improved. In this paper, the biodegradable films exhibited excellent ultraviolet light conversion ability and mechanical properties.     

Analysis of multiple melting behavior of spherulites comprising ring‐band shell/ringless core in polymorphic poly(butylene adipate)

In‐depth interpretation of ring‐banded spherulitic morphology, crystals, polymorphism, and complex melting behavior in poly(1,4‐butylene adipate) (PBA) were analyzed via a procedure of designing composite core‐shell spherulites, in which two lamellar patterns (ring‐band vs. ringless) were packed by subjecting to crystallization at two‐step temperature schemes with specific temperatures and times. By heating to 52 °C and holding at that temperature for 30 min annealing, the core can be stripped off by melting, and analysis specifically on the ring‐shell portion (with the ringless core stripped by controlled melting) proves that the highest melting peak (P₄ at 55–57 °C) is likely associated with melting of the ring‐band lamellae. Furthermore, the unusually complex multiple melting in PBA can be attributed to all three widely proposed mechanisms: (1) multiple types of lamellae preexisting in crystallized PBA, (2) scan/heating induced remelting/reorganization, and (3) polymorphism of dual crystal cells. In addition, this study evidently shows that the extinction rings within the ring‐banded shell, regardless of alternate edge‐on and flat‐on mechanism or alternative origins, can be of all singly α‐crystal form, either initially or upon postheating temperature‐induced transformation. Thus, the type of crystal forms (α or β) in polymorphic PBA is mainly associated with temperature of crystallization (T_c = 28 or 35 °C), and not likely with lamellar orientation (flat‐on or edge‐on). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 892–899, 2008     

Atomic Force Microscopy Characterization and Interpretation of Thin‐Film Poly(butylene adipate) Spherulites with Ring Bands

Atomic force microscopy characterization has been conducted to reveal the morphological difference between single‐ring bands in poly(butylene adipate) (PBA). Furthermore, morphological features of the ring‐less Maltese‐cross spherulites are compared to the ring‐band spherulites. Periodic changes in height seem to be common for either the ring‐band or ring‐less (Maltese‐cross) crystal domains; however, the steepness in height change is greater for the ring‐band crystal, while height change in the ring‐less crystal exhibits a terrace‐like layer pattern. In the ring‐band crystal region, the lamellar stalks, which taper off to pointed needle‐like stalks, monotonously protrude out of the layers of softer materials, with no signs of twisting, bending, or turning. In contrast, all lamellae in the ring‐less (Maltese‐cross) crystal region are uniform platelets arranged like flower petals in a layered pattern.

     

Thermal and mechanical properties of mandelic acid‐copolymerized poly(butylene succinate) and poly(ethylene adipate)

Phenyl side chains were introduced to poly(butylene succinate) and poly(ethylene adipate) by the polymerization of the respective monomers in the presence of mandelic acid. The increasing content of the phenyl side chains decreased the melting temperature and the crystallinity but increased the glass‐transition temperature of the aliphatic polyesters. The phenyl side branches reduced the crystallinity of poly(butylene succinate) more significantly than the ethyl or n‐octyl side branches did. The tensile strength, elongation, and tear strength of poly(ethylene adipate) decreased with an increase in the content of mandelic acid units. However, the increasing content of mandelic acid units enhanced the elongation and tear strength of poly(butylene succinate) considerably without a notable deterioration of tensile strength. The biodegradability of the copolyesters was increased as a result of the introduction of more mandelic acid units due to the decrease in the crystallinity. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1504–1511, 2000     

Effects of crystallization temperature and blend ratio on the crystal structure of poly(butylene adipate) in the poly(butylene adipate)/poly(butylene succinate) blends

The effects of crystallization temperature and blend ratio on the polymorphic crystal structures of poly(butylene adipate)(PBA) in poly(butylene succinate)(PBS)/poly(butylene adipate)(PBS/PBA) blends were studied by means of differential scanning calorimetry(DSC), wide-angle X-ray diffraction(XRD) and atomic force microscopy(AFM). It was revealed that the polymorphism of PBA can be regulated by the blend ratio even in a non-isothermal crystallization process. The results demonstrate that high temperature favors flat-on α crystals, while low temperature contributes to edge-on β crystals. It was also found that the effect of blend ratio on the crystallization mechanism of PBA is well coincident with that of the crystallization temperature. The increment of PBS content in the PBS/PBA blend gives rise to more β-form crystals of PBA. For those PBS/PBA blends with low PBA content, the interlamellar phase segregation of PBA makes its molecular chains so difficult to diffuse from one isolated microdomain to another that high crystallization temperature and sufficiently long crystallization time will be required if the PBA α-type crystals are targeted.     

Synthesis,characterization and isothermal crystallization behavior of poly(butylene succinate)‐b‐poly(diethylene glycol succinate) multiblock copolymers

In order to modify the properties of poly(butylene succinate), poly(diethylene glycol succinate) (PDGS) segment was incorporated by chain‐extension reaction of dihydroxyl‐terminated PBS and PDGS precursors using hexamethylene diisocyanate as a chain extender to form PBS‐b‐PDGS multiblock copolymers. The chemical structure and basic physical properties of the multiblock copolyesters were characterized by nuclear magnetic resonance spectroscopy, differential scanning calorimeter (DSC), wide angle X‐ray diffraction, and tensile testing. The results suggested that the incorporation of PDGS segments would increase the elongation at break of PBS significantly while decrease its melting temperature and crystallization temperature slightly. The isothermal crystallization kinetics studied by DSC and polarized optical microscopy indicated that the crystallization rate of the multiblock polymers decreased gradually with increasing PDGS segment content while the crystallization mechanism kept unchanged and the spherulitic growth rate of the multiblock copolymers decreased gradually with increase in PDGS content due to its diluent effect to the crystallization of PBS segments. Copyright © 2015 John Wiley & Sons, Ltd.     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Synchronous stimuli of biodegradable poly(butylene succinate‐co‐terephthalate) copolymer via uniaxial stretching at varying temperatures

Clearly knowing the structural responses of polymers to the treatment conditions is essential to regulate their final properties during industrial processing such as spinning, extrusion, injection, and blow molding. In this work, we reported the changes of hierarchical structure in poly(butylene succinate‐co‐terephthalate) (PBST) copolymer upon application of synchronous stimuli via uniaxial stretching at varying temperatures. The lamellae melting and the transition of crystal structure from α to β form in PBST copolymer always presented at the early stage of the deformation at different temperatures. The lamellae oriented to about ± (40–50)° direction as the yielding response to the stimuli. Upon further stretching, the oriented lamellae were freshly and progressively formed at high temperature, whose morphology was controllable by regulating the synchronous stimuli. Furthermore, a schematic for the structural responses to the synchronous stimuli was proposed. The structural responses of PBST copolymer under such synchronous stimuli are beneficial to tailor the final properties of the products in the form of fibers, films, plastics, and so forth, which also can provide new insights into the design and development of other copolymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 640–649     

Synthesis and Characterization of Poly（butylene adipate-co-terephthalate） Catalyzed by Rare Earth Stearates

Rare earth （Nd, Y, La, Dy） stearates have been synthesized and used as single component catalysts for the polycondensation of dimethyl terephthalate, adipic acid and 1,4-butanediol for the first time preparing biodegradable poly（butylene adipate-co-terephthalate） （PBAT） with high molecular weight, The microstructures of PBAT were characterized by ^1H NMR spectra. The PBAT exhibits good mechanical properties such as high tensile strength （ca. 20 MPa） and long break elongation （〉700%）.