Characterization of form-stable phase-change material for solar photovoltaic cooling

Solar PV panel cooling is essential to achieve maximum efficiency of PV modules. Phase-change material (PCM) is one of the prominent options to cool the panel and reduce the temperature, since PCMs have low thermal conductivity. Expanded graphite particles are used to enrich the structure and stability as well as to increase the thermal properties. In the present research work, polyethylene glycol (PEG) 1000 is used as a base material and expanded graphite for inclusive particle. A novel form-stable PEG1000/EG composite PCM mixture is prepared, using impregnation and dispersion method. Expanded graphite and PEG1000/EG sample phase compositions are investigated, using X-ray diffraction technique. No new peak is identified in the composite PCM sample. The surface morphology and structure of EG and PEG1000/EG are investigated, using scanning electron microscopy (SEM). Chemical stability analysis is done by Fourier-transform infrared spectroscopy. Thermal properties of the prepared composite PCMs are analysed by differential scanning calorimetry, thermogravimetric analysis (TGA) and KD2 pro analyser. Results show that addition of EG in various propositions (5%, 10% and 15%) enhances the thermal conductivity of PCM samples from 0.3654 to 1.7866 W mK^?1, while melting point and latent heat of fusion of PCM samples are getting reduced. TGA thermographs are used to investigate the thermal stability of the composite PCM samples. TGA curves show that loss of mass happens above the operating temperature, and it is varied with different mass ratios of EG. Characterization of the prepared composite PCM samples is compared and found that PEG1000-85%/EG-15% is the best form-stable PCM, suitable for cooling the solar PV panel as well as to improve the electrical efficiency coupled with a decrease of temperature in the range of 35 °C to 40 °C.

     

Synthesis and properties of bulk-biodegradable phase change materials based on polyethylene glycol for thermal energy storage

The bulk-biodegradable solid–solid phase change materials (SSPCMs) based on phase change polyethylene glycol (PEG) were synthesized by solvent-free polyaddition. On the basis of the fact that the water absorption is up to 800 mass% and that the poly(ethylene oxide) molecular chains can be degraded by microorganisms, the bulk-biodegradable mechanism of SSPCMs was put forward and studied. The X-ray diffraction patterns and the polarizing optical microscopy images show the SSPCMs possess the defective crystal and small grain compared with PEG. The differential scanning calorimetry data demonstrate the melting temperature and enthalpy of the synthesized SSPCMs are, respectively, 41 °C and 128 J g^?1. The bulk-biodegradable SSPCMs have the preeminent thermal reliability and the high thermal stability due to the onset thermal degradation temperature above 302 °C, which will give a good insight into bulk-biodegradable PCM system.     

Solid state photopolymerization of acrylic acid at low temperature

Near‐infrared spectroscopy was used to investigate the kinetic characteristics of acrylic acid photopolymerized at ?70°C and room temperature, respectively. The obtained results showed that at ?70°C the double bond conversion increased with increase in the initiator's concentration. Addition of soft chain component polyethylene glycol 400 (PEG400) could lead to high conversion in the solid state, and then high final double bond conversion after post‐curing. The introduction of water at low temperature also contributed largely to the enhancement in the initial and final double bond conversion in solid state. SEM photographs showed that more pores came up in the cured films with the increase in the water content in the reaction system. The change in the photoinitiator concentration, amount of PEG400, and content of water had significant effect on samples cured at lower temperature than at room temperature under the same conditions. Different kinds of photoinitiators showed different contributions to the initial and final double bond conversion on photopolymerization of acrylic acid at low temperature. Significant post‐curing phenomena for photopolymerization of acrylic acid at low temperature could be observed as well. Copyright © 2009 John Wiley & Sons, Ltd.     

Thermophysical properties and material modelling of acrylic bone cements used in vertebroplasty

The stabilization of osteoporotic vertebrae with acrylic bone cement, called vertebroplasty, is a common procedure in modern surgery. However, the thermomechanical-chemically coupled material behaviour of curing bone cements makes the application even for experienced surgeons difficult and can lead to potential complications like heat necrosis, leaking bone cement, embolisms and postoperative load shifting. In order to reduce these potential complications, to minimize the risks and to better understand the occurring effects, the thermophysical properties of a commercial acrylic bone cement were investigated in detail using differential scanning calorimetry, volumetric dilatometry and temperature controlled rheometry. More specifically, the reaction kinetics, the specific heat, the thermal conductivity, the thermal expansion, the chemical shrinkage as well as the mechanical behaviour was studied during the reaction process of the bone cement. Furthermore, the explored material behaviour is described by a customized material model that takes into account all observed effects. With the aid of this model the inhomogeneous chemical, thermal and mechanical states that appear during the application and curing of acrylic bone cements, can be studied by finite element treatment.     

Synthesis and characterization of high molecular weight poly(1,2-propylene carbonate-<Emphasis Type="Italic">co</Emphasis>-1,2-cyclohexylene carbonate) using zinc complex catalyst

Using supported multi-component zinc dicarboxylate catalyst,poly（1,2-propylene carbonate-co-1,2-cyclohexylene carbonate）（PPCHC） was successfully synthesized from carbon dioxide（CO₂） with propylene oxide（PO） and cyclohexene oxide（CHO）.The conversion of epoxides dramatically increased up to 89.7%（yield:384.2 g of polymer per g of Zn） with increasing reaction temperature from 60℃to 80℃.The optimized reaction temperature is 80℃.The chemical structure,the molecular weight,as well as thermal and mechanical properties of the resulting terpolymers were investigated extensively. When CHO feed content（mol%） is lower than 10%,the PPCHC terpolymers have number average molecular weight（M_n） ranging from 102×10³ to 202×10³ and molecular weight distribution（MWD） values ranging from 2.8 to 3.5.In contrast to poly（propylene carbonate）（PPC）,the introduction of small amount of CHO leads to increase in the glass transition temperature from 38.0℃to 42.6℃.Similarly,the mechanical strength of the synthesized terpolymer is greatly enhanced due to the incorporation of CHO.These improvements in mechanical and thermal properties are of importance for the practical application of PPC.     

Synthesis and characterization of a nano‐hydroxyapatite/chitosan/polyethylene glycol nanocomposite for bone tissue engineering

A novel nanocomposite involving nano‐hydroxyapatite/chitosan/polyethylene glycol (n‐HAP/CS/PEG) has been successfully synthesized via co‐precipitation approach at room temperature. The purpose to synthesize such nanocomposite is to search for an ideal analogue which may mimick the composition of natural bone for bone tissue engineering with respect to suitable biocompatibility, cytotoxicity and mechanical properties. The FTIR spectra of n‐HAP/CS and n‐HAP/CS/PEG scaffolds indicated significant intermolecular interaction between the various components of both the nanocomposites. The results of XRD, TEM and TGA/DTA suggested that the crystallinity and thermal stability of the n‐HAP/CS/PEG scaffold have decreased and increased respectively, relative to n‐HAP/CS scaffold. The comparison of SEM images of both the scaffolds indicated that the incorporation of PEG influenced the surface morphology while a better in‐vitro bioactivity has been observed in n‐HAP/CS/PEG than in n‐HAP/CS based on SBF study, referring a greater possibility for making direct bond to living bone if implanted. Furthermore, MTT assay revealed superior non‐toxic nature of n‐HAP/CS/PEG to murine fibroblast L929 cells as compared to n‐HAP/CS. The comparative swelling studies of n‐HAP/CS/PEG and n‐HAP/CS scaffolds revealed a better swelling rate for n‐HAP/CS/PEG. Also n‐HAP/CS/PEG showed higher mechanical strength relative to n‐HAP/CS supportive of bone tissue ingrowths. Copyright © 2014 John Wiley & Sons, Ltd.     

An intrinsic antistatic polyethylene glycol-based solid–solid phase change material for thermal energy storage and thermal management

Polyethylene glycol (PEG) is an important and popular phase change material (PCM), but is not a good antistatic material, which would cause the accumulation of static electricity and electrostatic discharge when used for the thermal energy storage and thermal management of electrical devices. Herein, we prepared a PEG-based solid–solid PCM (SSPCM) with good antistatic property by introducing an ionic liquid onto the macromolecular chains. This SSPCM is in solid state even at 90°C, avoiding the leakage issue of pure PEG. Its latent heat values in the melting and solidifying processes are 56.2 and 30.6 J g⁻¹, respectively. Additionally, this SSPCM has good thermal stability and thermal reliability for thermal storage and thermal management according to thermogravimetric and thermal cycling tests. The volume- and surface resistivity of the SSPCM at ambient temperature are 10^8.87 Ω m and 10^8.92 Ω, respectively, showing good antistatic performance.     

Irreversible temperature‐responsive formation of high‐strength hydrogel from an enantiomeric mixture of starburst triblock copolymers consisting of 8‐arm PEG and PLLA or PDLA

Starburst triblock copolymers consisting of 8‐arm poly(ethylene glycol) (8‐arm PEG) and biodegradable poly(L ‐lactide) (PLLA) or its enantiomer poly(D ‐lactide) (PDLA), 8‐arm PEG‐b‐PLLA‐b‐PEG ( Stri‐L ), and 8‐arm PEG‐b‐PDLA‐b‐PEG ( Stri‐D ) were synthesized. An aqueous solution of a 1:1 mixture ( Stri‐Mix ) of Stri‐L and Stri‐D assumed a sol state at room temperature, but instantaneously formed a physically crosslinked hydrogel in response to increasing temperature. The resulting hydrogel exhibited a high‐storage modulus (9.8 kPa) at 37 °C. Interestingly, once formed at the transition temperature, the hydrogel was stable even after cooling below the transition temperature. The hydrogel formation process was irreversible because of the formation of stable stereocomplexes. In aqueous solution, gradual hydrolytic erosion was observed because of degradation of the hydrogel. The combination of rapid temperature‐triggered irreversible hydrogel formation, high‐mechanical strength, and degradation behavior render this polymer mixture system suitable for use in injectable biomedical materials, for example, as a drug delivery system for bioactive reagents or a biodegradable scaffold for tissue engineering. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6317–6332, 2008     

Triazole Functionalized Sol-Gel Membranes,Effect of Crosslink Density and Heterocycle Content on Water Free Proton Conduction and Membrane Mechanical Properties

Freestanding, ion conducting, membranes were synthesized by incorporating triazole-containing tetracyclosiloxanes into a polyethylene glycol-tetraethyl orthosilicate (PEG-TEOS) based sol-gel matrix. These membranes show comparable or higher proton conductivities than their linear, liquid, polysiloxane analogs and fall within an order of magnitude of the target ion mobilities for use in proton exchange membrane fuel cells (PEMFC's). The absence of any unbound PEG or cyclic siloxane was confirmed by proton nuclear magnetic resonance (¹H-NMR), while the chemical structure and composition of the membranes was corroborated by Fourier transform infrared (FTIR) spectroscopy. Thermogravimetric analysis (TGA) indicated that the membranes are stable up to 180°C and differential scanning calorimetry (DSC) analysis showed complete suppression of PEG crystallization after incorporation of the triazole-functionalized cyclosiloxanes. An increase in the molecular weight of the PEG chains used to create the sol-gel matrix produced membranes with increased flexibility and higher proton conductivities at temperatures below 100 °C. Pulse field gradient echo (PFG) NMR studies showed an increase in the apparent diffusion coefficient of the sol-gel threaded cyclosiloxane motifs compared to the linear polysiloxanes, indicating a significant reduction on the coupling between mechanical strength and ion transport capability.     

Spatiotemporal Utilization of Latent Heat in Erythritol-based Phase Change Materials as Solar Thermal Fuels

Solar thermal fuels (STFs) have been particularly concerned as sustainable future energy due to their impressive ability to store solar energy in chemical bonds and controllably release thermal energy. However, currently studied STFs mainly focus on molecule-based materials with high photochemical activity, toxicity, and compromised features, which greatly restricts their applications in practical scenarios of solar energy utilization. Herein, we present a novel erythritol-based composite phase change material (PCM) as a new type of STFs with an outstanding capability to store solar energy as latent heat in its stable supercooling state and release thermal energy as needed. This composite PCM with stored thermal energy can be maintained stably at room temperature and subsequently release latent heat as high as 224.9 J/g during the crystallization process triggered by thermal stimuli. Remarkably, solar energy can be converted into latent heat stored in the composite PCM over months. Through mechanical stimulations, the released latent heat can increase the temperature of the composite up to 91 °C. This work presents a new concept of using spatiotemporal storage and release of latent heat in PCMs for solar energy utilization, making it a potential candidate as STFs for developing future clean energy techniques.     

Investigation of early hydration of high aluminate cement-based binder at different ambient temperatures

The effect of spent FCC catalyst on early hydration (up to 48?h) of high aluminate cement (Al₂O₃ >70%) at different ambient temperatures (10, 20, and 30?°C) was investigated. Cement pastes with constant ratio of water/binder?=?0.35 (binder?=?cement?+?addition) and containing 0, 5, 10, and 15% mass of addition as replacement of cement were studied. The hydration kinetics was determined by calorimetric measurements and the structure of hardened binders after 2?days of curing at an appropriate temperature was also investigated using X-ray, SEM, and thermal analysis methods. Due to the fact that hydration of aluminate cements is highly sensitive to temperature conditions as well as certain changes of temperature are inevitable in practice, the evaluation of the impact of the waste catalyst addition in such conditions is justified. On the basis of obtained results, it was stated that the temperature determines the early hydration of high aluminate cement and decides about the influence of waste aluminosilicate. The introduction of the discussed addition has a big impact on the kinetics of cement hydration closely related to the curing temperature. The presence of spent catalyst accelerates the hydration at the temperatures of 20 and 30?°C, but at the temperature of 10?°C this waste aluminosilicate acts as a retarding agent. The effect of the addition on the microstructure of hardened binders after 48?h of hydration is rather insignificant, especially at 20?°C, compared to the influence of the temperature on hydration. At the temperature of 10?°C, a formation of low amount of C₂AH₈ can be observed because of the presence of spent catalyst, while at the temperature of 30?°C the introduction of the mineral addition prevents the hydrogarnet formation.     

Detection of joint capsule changes by differential scanning calorimetry (DSC) in different types of hip disorders to evaluate surgical techniques (a preliminary report)

In this study, paraffin-/ultrasonic-treated diatomite was characterized for use as phase change material (PCM) for thermal energy storage in buildings. The diatomite was treated with ultrasound at various periods of time. The diatomite treated with ultrasound for 60 min (DA-60) was the optimum condition providing the highest surface area without structural degradation. The melting point and latent heat of the paraffin/DA-60 composite PCM were 59 °C and 45.90 J g^?1, respectively. The obtained form-stable PCM had good thermal reliability after 500 cycles of thermal cycling test. The thermal performance of PCM was tested by incorporating the paraffin/DA-60 composite PCM into gypsum board. The results showed that the gypsum board containing the paraffin/DA-60 composite PCM had better thermal energy absorption and release characteristics than those of the control sample. The incorporation of paraffin/DA-60 composite PCM into suitable building materials could thus considerably reduce the energy consumption of cooling system in buildings.     

Defect mode and crystal-electric-field effects on the thermal expansion and heat capacity of RB<Subscript>50</Subscript> boride

This study aimed to evaluate the suitability of using unfired and fired pumice as cement replacement materials as well as their effect on the thermal resistance of hardened ordinary Portland cement (OPC) pastes. Different OPC–pumice (unfired and fired) blends were prepared by partial replacement of OPC by 0, 10 and 20 of pumice (mass%). The effect of the addition of 1 and 5 % of active alumina on the mechanical properties and thermal resistance of different OPC–pumice (unfired) blends was investigated. The fire resistance test was done by exposing the hardened blended cement cubes to elevated temperatures of 200, 400, 600 and 800 °C for 3 h and allowed them to cool down to room temperature before testing for their mechanical properties. The phase composition and thermal analysis of some selected specimens were investigated by XRD, DSC and DTA/TG techniques. The obtained results indicated that replacing OPC by 10 and 20 % by pumice (unfired and fired) improved its thermal stability at different firing temperatures. The cement blend prepared by replacement of OPC with 10 % pumice showed the highest fire resistance. The addition of 1 and 5 % of alumina (A) to OPC–pumice blends causes a notable improve in their mechanical properties and thermal resistance.     

Nanoclay modified silica phenolic composites: mechanical properties and thermal response under simulated atmospheric re‐entry conditions

Ablative nanocomposites based on nanoclay‐dispersed addition curable propargylated phenolic novolac (ACPR) resin, reinforced with chopped silica fiber, were investigated for their thermal response behavior under simulated heat flux conditions corresponding to typical atmospheric re‐entry conditions. Organically modified nanoclay (Cloisite 30B) was incorporated to different extents (1–10%) in the ACPR resin matrix containing silica fiber to form the composite. The composites displayed optimum mechanical properties at around 3 wt% of nanoclay loading. The resultant composites were evaluated for their ablative characteristics as well as mechanical, thermal and thermo‐physical properties. The reinforcing effect of nanoclay was established and correlated to the composition. The mechanical properties of the composites and its pyrolysed product improved at moderate nanoclay incorporation. Plasma arc jet studies revealed that front wall temperature is lowered by 20°C and that at backwall by 10–13°C for the 3 wt% nanoclay‐incorporated composites due to impedance by nanoclay for the heat conduction. Nanoclay diminished the coefficient of thermal expansion by almost 50% and also reduced the flammability of the composites. The trend in mechanical properties was correlated to the microstructural morphology of the composites. The nanomodification conferred better strength to the pyrolysed composites. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis and Characterization of a Novel High-Temperature Structural Adhesive Based on MDA-BAPP-BTDA Co-Polyimide

A series of polyimide(PI) adhesives were synthesized from 2,2'-Bis [4-(4-aminophenoxy)phenyl] propane(BAPP), 4,4'-Diaminodiphenylmethane (MDA) and 3,3',4,4'-Benzophenonetetracarboxylic acid dianhydride (BTDA) via a two-step process. PI adhesives with different BAPP content were characterized in regard to their structure, thermal stability, mechanical properties and adhesive performance. Results showed that these PIs had excellent thermal stability, whose glass transition temperature (Tg) were around 300°C. While, superior dynamic mechanical behavior was observed, and the maximum loss factor declined with the increase of BAPP content. Single-lap shear strength of over 15.58 MPa at room temperature was obtained, and it remained high even at the temperature of 350°C. Factors that could affect bonding strength of these PI adhesives such as molar ratio of the diamine monomers, surface roughness of adherends and curing processes were investigated.     

Direct synthesis of potentially biodegradable aromatic–aliphatic thermotropic copolyesters with photocrosslinking properties

ABSTRACT

In this study, aromatic–aliphatic thermotropic copolyesters derived from p-hydroxybenzoic acid, p-hydroxycinnamic acid (HCA), terephthalic acid and polyethylene glycol (PEG) with different molecular weight (200, 400, 600) were directly synthesised via Vilsmeier adduct solution polymerisation method. The structure, thermal behaviour, liquid crystal property, hydrophylicity and photoactivity were investigated by Fourier transform infrared and nuclear magnetic resonance spectroscopy, differential scanning calorimeter, polarised optical microscopy, water contact angle measurement and ultraviolet (UV) spectrophotometer. The PEG incorporation ratio is 0.540–0.691 related to the HCA units, because of its low reactivity. And, the copolyesters have relatively low melting temperatures (96–107°C) and good hydrophylicity (water contact angle value 61.2–75.3°) as compared with wholly aromatic thermotropic copolyester. All of the copolyesters exhibited nematic liquid crystal behaviour and the stable mesophase temperature range was more than 60°C after being melted. The resulted copolyesters had enough thermal stability for melt processing without any degradation. The UV absorption intensities decreased with increased irradiation time, indicating that photocrosslinking occurred.     

Functionalized graphene/thermoplastic polyester elastomer nanocomposites by reactive extrusion‐based masterbatch: preparation and properties reinforcement

A reactive extrusion process was developed to fabricate polymer/graphene nanocomposites with good dispersion of graphene sheets in the polymer matrix. The functionalized graphene nanosheet (f‐GNS) activated by diphenylmethane diisocyanate was incorporated in thermoplastic polyester elastomer (TPEE) by reactive extrusion process to produce the TPEE/f‐GNS masterbatch. And then, the TPEE/f‐GNS nanocomposites in different ratios were prepared by masterbatch‐based melt blending. The structure and morphology of functionalized graphene were characterized by Fourier transform infrared, X‐ray photoelectron spectroscopy, X‐ray diffraction and transmission electron microscopy (TEM). The incorporation of f‐GNS significantly improved the mechanical, thermal and crystallization properties of TPEE. With the incorporation of only 0.1 wt% f‐GNS, the tensile strength and elongation at break of nanocomposites were increased by 47.6% and 30.8%, respectively, compared with those of pristine TPEE. Moreover, the degradation temperature for 10 wt% mass loss, storage modulus at ?70°C and crystallization peak temperature (T_cp) of TPEE nanocomposites were consistently improved by 17°C, 7.5% and 36°C. The remarkable reinforcements in mechanical and thermal properties were attributed to the homogeneous dispersion and strong interfacial adhesion of f‐GNS in the TPEE matrix. The functionalization of graphene was beneficial to the improvement of mechanical properties because of the relatively well dispersion of graphene sheets in TPEE matrix, as suggested in the TEM images. This simple and effective approach consisting of chemical functionalization of graphene, reactive extrusion and masterbatch‐based melt blending process is believed to offer possibilities for broadening the graphene applications in the field of polymer processing. Copyright © 2014 John Wiley & Sons, Ltd.     

Tough crystalline blends of polylactide with block copolymers of ethylene glycol and propylene glycol

The effect of crystallinity of polylactide (PLA) on the structure and properties of tough PLA blends with PEG-b-PPG-b-PEG block copolymers was studied. PLA was melt blended with a set of the copolymers with varying ratio of the hydrophilic (PEG) and hydrophobic (PPG) blocks. Although the blend phase structure depended on the copolymer molar mass and PEG content, as well as on the copolymer concentration in the blend, crystallinity also played an important role, increasing the copolymer content in the amorphous phase and enhancing phase separation. The influence of crystallinity on the thermal and mechanical properties of the blends depended on the copolymer used and its content. The blends, with PLA crystallinity of 25 ÷ 34 wt%, exhibited relatively high glass transition temperature ranging from 45 to 52 °C, and melting beginning above 120 °C. Although with a few exceptions crystallinity worsened the drawability and toughness, these properties were improved with respect to neat crystalline PLA in the case of partially miscible blends, in which fine liquid inclusions of the modifier were dispersed in PLA rich matrix. About 20-fold increase of the elongation at break and about 4-fold increase of the tensile impact strength were reached at a small content (10 wt%) of the modifier. Moreover, crystallinity decreased oxygen and water vapor transmission rates through neat PLA and the blend, and the barrier property for oxygen of the latter was better than that of neat polymer.     

Rheological and thermal properties of stereocomplexed polylactide films

Poly(l-lactide) (PLLA) and Poly(d-lactide) (PDLA) blended films (PLLA/PDLA) were prepared (5/95; 25/75; 50/50, and 75/25) by solvent casting method. Blend of PLLA and PDLA of medium molecular mass led to the formation of stereocomplex which was evidenced by differential scanning calorimetry, rheological measurement and Fourier transform infrared spectroscopy. The stereocomplex had a higher melting temperature (T _m) (more than 50 °C) and crystallized at higher temperature (T _c) (more than 25 °C) from the melt compared to neat PLLA and PDLA. The T _m and T _c gradually decreased with increasing the number of thermal scans. The enthalpy of fusion (?H_m) for stereocomplex crystallites in 50/50 blend films was the highest than that of homo-crystallites. Rheological measurement at a temperature of 180–195 °C revealed that the neat PLA was predominantly liquid-like behavior (G″ > G′) which transformed to extreme solid-like behavior by incorporation of PDLA into PLLA. Among blends, 50/50 PDLA/PLLA showed the maximum mechanical strength (G′) followed by 25/75, 75/25, and 5/95 blends. The significant increase in mechanical strength is believed to be attributed by stereocomplex formation by blends. Thermal and rheological data supported higher mechanical strength and an increase in melting and crystallization temperature adequately.     

Studies on the graft copolymerization of cellulosic materials

Graft copolymers of acrylic acid on cellulosic materials were obtained by use of ceric ion in aqueous medium at various temperatures. The level of incorporation of poly(acrylic acid) grafts and the efficiency of grafting were significantly reduced as the temperature of polymerization was increased from 35° to 60°C. The uptake of cadmium and copperions from aqueous solution by the cellulose-g-poly(acrylic acid) copolymer was examined by equilibrium and dynamic sorption studies. The amount of metal ions removed from solution depended on the metal ion type, initial concentration of the metal ion solution, level of incorporation of poly(acrylic acid) in the graft copolymer and the temperature of the metal ion solution.