Preparation and characterization of TiO2/Pebax/(PSf‐PES) thin film nanocomposite membrane for humic acid removal from water

New thin film composite (TFC) membrane was prepared via coating of Pebax on PSf‐PES blend membrane as support, and its application in wastewater treatment was investigated. To modify this membrane, hydrophilic TiO₂ nanoparticles were coated on its surface at different loadings via dip coating technique. The as‐prepared membrane was characterized using Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), field emission SEM, and contact angle analysis. The Fourier transform infrared spectroscopy analysis and surface SEM images indicated that TiO₂ was successfully coated on the membrane surface. In addition, the results stated that the hydrophilicity and roughness of membrane surface increased by addition of TiO₂ nanoparticles. Performance of TFC and modified TFC membranes was evaluated through humic acid removal from aqueous solution. Maximum permeate flux and humic acid rejection were obtained at 0.03 and 0.01 wt% TiO₂ loadings, respectively. Rejection was enhanced from 96.38% to 98.92% by the increase of feed concentration from 10 to 30 ppm. Additionally, membrane antifouling parameters at different pressures and feed concentration were determined. The results indicated that surface modification of membranes could be an effective method for improvement of membrane antifouling property.     

Fabrication,characterization, and performance evaluation of polyethersulfone/TiO2 nanocomposite ultrafiltration membranes for produced water treatment

In the present work, development of neat and nanocomposite polyethersulfone membranes composed of TiO₂ nanoparticles is presented. Membranes are fabricated using nonsolvent phase inversion process with the objective of improving antifouling, hydrophilicity, and mechanical properties for real and synthetic produced water treatment. Membranes are characterized using scanning electron microscopy, Fourier‐transform infrared, contact angle, porosity measurement, compaction factor, nanoparticles stability, and mechanical strength. The performance of prepared membranes was also characterized using flux measurement and oil rejection. Fourier‐transform infrared spectra indicated that noncovalence bond formed between Ti and polyethersulfone chains. The contact angle results confirmed the improved hydrophilicity of nanocomposite membranes upon addition of TiO₂ nanoparticles owing to the strong interactions between fillers and water molecules. The increased water flux for nanocomposite membranes in comparison with neat ones can be due to coupling effects of improved surface hydrophilicity, higher porosity, and formation of macrovoids in the membrane structure. The membrane containing 7 wt% of TiO₂ nanoparticles was the best nanocomposite membrane because of its high oil rejection, water flux, antifouling properties, and mechanical stability. The pure water flux for this membrane was twice greater than that of neat membrane without any loss in oil rejection. The hydrophilicity and antifouling resistance against oil nominates developed nanocomposite membranes for real and synthetic produced water treatment applications with high performance and extended life span.     

Effect of polyaniline (PANI) on Poly(vinylidene fluoride-co-hexaflouro propylene) (PVDF-co-HFP) polymer electrolyte membrane prepared by breath figure method

Poly(vinylidene fluoride-co-hexaflouro propylene) is a well-known material for polymer electrolyte membranes (PEMs) due to its low cost, high mechanical integrity and excellent chemical resistance; however, its pure form has limited characteristics that require further modification to achieve optimum results. Therefore, the different dosages of polyaniline (PANI) (10 wt%, 20 wt%, 30 wt%, 40 wt% and 50 wt%) were incorporated into PVDF-HFP blend to fabricate PVDF-HFP/PANI polymer electrolyte membrane by using breath-figure method. The FTIR peaks of PVDF-HFP and PVDF-HFP/PANI membrane confirms the successful incorporation of PANI into PVDF-HFP blend, while TGA, DSC and XRD analysis shows the PANI effect on stability and ionic conductivity of PVDF-HFP membrane. The PVDF-HFP/PANI membrane with 30 wt% PANI found superior with the highest porosity of 83%, electrolyte uptake of 270% and ionic conductivity of 1.96 mS cm⁻¹; however, the other concentrations of PANI were also effective and enhanced the performance of PVDF-HFP membrane. This shows the improved performances of PVDF-HFP membrane were attributed to successful incorporation of PANI and the proposed membrane can be a suitable alternative PEM or a separator for energy devices.     

Fabrication of PES-based nanofiltration membrane modified by composite PAA-co-PMMA-g-ZnA nanoparticles

In the current research, nanocomposite polyethersulfone-based nanofiltration membranes were prepared by composite PAA-co-PMMA-g-ZnA nanoparticles. NF membranes were fabricated by phase inversion through casting solution technique. The effect of composite PAA-co-PMMA-g-ZnA nanoparticles concentration into the casting solution on physicochemical characteristics of membrane was studied. Scanning optical microscopy images showed uniform particle distribution for the membranes. Scanning electron microscopy images also demonstrated that membrane porosity was enhanced by increase in nanoparticles content ratio. The membrane surface 3D images showed smooth surface for the membranes filled with 0.05, 0.1 and 0.5 wt% nanoparticles. The contact angle results exhibited that membrane hydrophilicity was improved significantly by using of NPs in membrane matrix. The contact angle was decreased from 65.38° for PES membrane to 48.33° for membrane filled with 0.5 wt% nanoparticles. The water permeability was reduced initially by addition of 0.05 wt% nanoparticles into the casting solution and then increased by more nanoparticles loading rate (0.1 wt%). The water permeability was decreased again by more increase in nanoparticles loading range from 0.5 to 1 wt%. The salt rejection was improved strongly from 68.4 % for PES to 88.58 % for membrane filled with 0.5 wt% nanoparticles. The membranes mechanical strength was increased sharply from 2835.5 to 3337.3 kPa with addition of nanoparticles into the casting solution.     

Solvothermal synthesis of WO3/TiO2/carbon fiber composite photocatalysts for enhanced performance under sunlight illumination

Carbon fiber (CF)‐based WO₃/TiO₂ composite catalysts (WO₃/TiO₂/CF) were successfully synthesized by solvothermal method. The catalysts were characterized by XPS, SEM, BET, XRD, FTIR, Raman and UV–Vis. The analyses confirmed the WO₃/TiO₂ nanoparticles with high crystallinity deposited on the carbon structure. The photocatalytic degradation of Orange II azo dye under UV and sunlight illumination with the synthesized catalyst was explored. The composite catalyst displayed high performance (85%) for Orange II degradation while that of for WO₃/TiO₂ was found as 76%. The effects of CF amount, solution pH, initial dye concentration and catalyst dose on photocatalytic performance were studied. It was found that the degradation efficiency increased from 68% to 90% with the increasing CF amount from 3 wt% to 5 wt%, while the further increase in CF amount (7–10 wt%) decreased the photodegradation due to the blocking the active sites of WO₃/TiO₂. The enhanced photocatalytic efficiency was mainly attributed to the electrical properties of the CF and reduced bandgap.     

Nanostructured polyethersulfone membranes for dye and protein separation: Exploring antifouling role of holmium (III) molybdate nanosheets

Nanostructured polymer membranes are nowadays of crucial importance in achieving antifouling properties. Nanomaterials with tunable composition, size, and morphology, surface modification and functionality offer unprecedented opportunities for efficient wastewater treatment. In this work, the effect of holmium (III) molybdate (Ho₂MoO₆) nanomaterial as a new nanofiller on preparation of nanostructured polyethersulfone (PES) mixed matrix membranes was examined in terms of hydrophilicity, membrane morphology, permeability, dye and protein separation and antifouling property. The Ho₂MoO₆ nanosheets were synthesized and characterized by FTIR, XRD, and FESEM and used in different amounts in PES matrix. The pore size and the membrane porosity increased with Ho₂MoO₆ loading. The nanocomposite membranes showed enhancement in hydrophilicity, antifouling properties, dye rejection and permeability. The remarkably pure water flux (195 L/m²h at 3 bar) and 92.3% flux recovery after bovine serum albumin (BSA) filtration were obtained for the membrane mixed with 2 wt% Ho₂MoO₆ compared to 95 L/m²h and 75.2% obtained for the bare PES, respectively. Moreover, significantly high rejection of Acid Red 125 (95 ± 1%) was achieved. Thus, the experimental results established the potential efficiency of the novel nanocomposite membrane for the separation applications.     

Formation of appropriate sites on nanofiltration membrane surface for binding TiO2 photo-catalyst: Performance, characterization and fouling-resistant capability

Titanium dioxide (TiO₂) nanoparticles were assembled on the surface of nanofiltration blend membrane. For settling TiO₂ on the membrane surface, two membrane categories were used: (i) unmodified polyethersulfone (PES)/polyimide (PI) blend membrane, and (ii) –OH functionalized PES/PI blend membrane with different concentrations of diethanolamine (DEA). These membranes were radiated by UV light after TiO₂ depositing with different concentrations. 15 min immersion in colloidal suspension and 15 min UV irradiation with 160 W lamps were used for modification. The modification resulted in the formation of a photo-catalytic property with enhanced membrane hydrophilicity. The self-assembly of TiO₂ nanoparticles was established through coordinance bonds with –OH functional groups on the membrane surface. A comparison between the UV irradiated TiO₂ deposited blend membrane and deposited-functionalized blend membranes showed that –OH groups originate excellent adhesion of TiO₂ nanoparticles on the membrane surface, increase reversible deposition, and diminish irreversible fouling. The membranes were characterized using SEM, FTIR, EDX, contact angle, cross flow filtration, and antifouling measurements. SEM images show that the presence of –OH groups on the DEA-modified membrane surface is the main parameter for extra uniformly settlement of TiO₂ nanoparticles on the membrane surface. This procedure is a superior technique for modification of PES/PI nanofiltration membranes to enhance water flux and minimization membrane fouling.     

Enhancing the antifouling property of polyethersulfone ultrafiltration membranes through surface adsorption-crosslinking of poly(vinyl alcohol)

An adsorption-crosslinking process of poly(vinyl alcohol) (PVA) was introduced to modify the surface of polyethersulfone (PES) ultrafiltration membranes for enhancement of their antifouling property. XPS and water contact angle measurement confirmed the obvious enhancement of surface hydrophilicity. Ultrafiltration results showed that the spreading of PVA chains over the hydrophobic membrane surface caused substantial but acceptable decrease on membrane flux. The fouling type analysis indicated that PVA adsorption effectively improved the antifouling property of PES membranes. With a PVA concentration of 0.5 wt% and three cycles of alternative adsorption-crosslinking, the total and irreversible fouling ratio of modified membranes were 0.38 and 0.22, respectively, much lower than those of control PES membrane (0.61 and 0.47), and the flux recovery ratio was increased accordingly. The long-term ultrafiltration experiment demonstrated the improvement of recycling property and the reliability of adsorption-crosslinking process.     

Versatility of hydrophilic and antifouling PVDF ultrafiltration membranes tailored with polyhexanide coated copper oxide nanoparticles

Hydrophilic poly(vinylidene fluoride) (PVDF) nanocomposite ultrafiltration (UF) membranes with excellent antifouling and antibiofouling characteristics are fabricated by employing polyhexanide coated copper oxide nanoparticles (P–CuO NPs). The presence of P–CuO NPs is played a significant role in altering the PVDF membrane matrix and probed by XRD, FTIR, FESEM and contact angle analysis. The PVDF/P–CuO nanocomposite membranes exhibited an outstanding antifouling performance indicated by the superior pure water flux, effective foulant separation and maximum flux recovery ratio during UF experiments as a result of the formation of the hydrophilic and more porous membrane due to the uniform distribution of P–CuO NPs. Particularly, the PVDF/P–CuO-3 membrane showed higher PWF of 152.5 ± 2.4 lm⁻²h⁻¹ and porosity of 64.5% whereas the lower contact angle of 52.5°. Further, it showed the higher rejection of 99.5 and 98.4% and the flux recovery ratio of 99.5 and 98.5% respectively for BSA and HA foulants, demonstrated its increased water permeation, foulant separation and antifouling behavior. Further, the decent antibacterial activity is showed by the PVDF/P–CuO nanocomposite membranes with the formation of halo-zone around the membrane when exposed to the bacterial medium demonstrated that, by this process an antibacterial water treatment membrane can be developed by simple phase inversion technique with good membrane stability.     

Quantitative Raman and ESCA characterization of titania supported tungsten catalysts

Summary The distribution of supported species in a series of W/TiO₂ catalysts (1.8 – 28 wt% WO₃) has been determined by Raman and X-ray photoelectron spectroscopy (XPS, ESCA). The results show that three tungsten species are present on oxidic W/TiO₂ catalysts. A tungsten interaction species is formed almost exclusively for catalysts with W loadings lower or equal to 6.7 wt% WO₃. WO₃ is observed above 6.7 wt% WO₃. For W loadings higher than 10 wt%, a disordered W species W_DS is also present. The amounts of W_DS and WO₃ increase with increasing W content above 10 wt% WO₃.Dedicated to Professor Dr. Wilhelm Fresenius on the occasion of his 80th birthday     

Anisotropic Self‐Assembly of Citrate‐Coated Gold Nanoparticles on Fluidic Liposomes

The behavior of self‐assembly processes of nanoscale particles on plasma membranes can reveal mechanisms of important biofunctions and/or intractable diseases. Self‐assembly of citrate‐coated gold nanoparticles (cAuNPs) on liposomes was investigated. The adsorbed cAuNPs were initially fixed on the liposome surfaces and did not self‐assemble below the phospholipid phase transition temperature (T_m). In contrast, anisotropic cAuNP self‐assembly was observed upon heating of the composite above the T_m, where the phospholipids became fluid. The number of self‐assembled NPs is conveniently controlled by the initial mixing ratio of cAuNPs and liposomes. Gold nanoparticle protecting agents strongly affected the self‐assembly process on the fluidic membrane.     

Modification and characterization of semi-crystalline poly(vinyl alcohol) with interpenetrating poly(acrylic acid) by UV radiation method for alkaline solid polymer electrolytes membrane

Semi-crystalline poly(vinyl alcohol) was modified by UV radiation with acrylic acid monomer to get interpenetrating poly(acrylic acid) modified poly(vinyl alcohol), PVAAA, membrane. The stability of various PVAAA membranes in water, 2 M CH₃OH, 2 M H₂SO₄, and 40 wt% KOH aqueous media were evaluated. It was found that the stability of PVAAA membrane is stable in 40 wt% KOH solution. The PVAAA membranes were characterized by differential scanning calorimetry, X-ray diffraction, and thermogravimetry analysis. These results show that (1) the crystallinity in PVAAA decreased with increasing the content of poly(acrylic acid) in the PVAAA membranes. (2) The melting point of the PVAAA membrane is reduced with increasing the content of poly(acrylic acid) in the membrane. (3) Three stages of thermal degradation were found for pure PVA. Compared to pure PVA, the temperature of thermal degradation increased for the PVAAA membrane. The various PVAAA membranes were immersed in KOH solution to form polymer electrolyte membranes, PVAAA-KOH, and their performances for alkaline solid polymer electrolyte were conducted. At room temperature, the ionic conductivity increased from 0.044 to 0.312 S/cm. The result was due to the formation of interpenetrating polymer chain of poly(acrylic acid) in the PVAAA membrane and resulting in the increase of charge carriers in the PVA polymer matrix. Compared to the data reported for different membranes by other studies, our PVAAA membrane are highly ionic conducting alkaline solid polymer electrolytes membranes.     

Selectivity in the Ligand Functionalization of Photocatalytic Metal Oxide Nanoparticles for Phase Transfer and Self-Assembly Applications

The functionalization of photocatalytic metal oxide nanoparticles of TiO₂, ZnO, WO₃ and CuO with amine-terminated (oleylamine) and thiol-terminated (dodecane-1-thiol) alkyl-chain ligands was studied under ambient conditions. A high selectivity was observed in the binding specificity of a ligand towards nanoparticles of these different oxides. It was observed that oleylamine binds stably to only TiO₂ and WO₃, whereas dodecane-1-thiol binds stably only to ZnO and CuO. Similarly, polar-to-nonpolar solvent phase transfer of TiO₂ and WO₃ nanoparticles could be achieved by using oleylamine, but not dodecane-1-thiol, whereas the opposite holds for ZnO and CuO. The surface chemistry of ligand-functionalized nanoparticles was probed by attenuated total reflectance (ATR)-FTIR spectroscopy, which enabled the occupation of the ligands at the active sites to be elucidated. The photostability of the ligands on the nanoparticle surface was determined by the photocatalytic self-cleaning properties of the material. Although TiO₂ and WO₃ degrade the ligands within 24 h under both UV and visible light, ligands on ZnO and CuO remain unaffected. The gathered insights are also highly relevant from an application point of view. As an example, because the ligand-functionalized nanoparticles are hydrophobic in nature, they can be self-assembled at the air-water interface to give nanoparticle films with demonstrated photocatalytic as well as anti-fogging properties.     

Preparation and characterization of (Pebax 1657 + silica nanoparticle)/PVC mixed matrix composite membrane for CO<Subscript>2</Subscript>/N<Subscript>2</Subscript> separation

In this work, the films of poly(ether-block-amide) (Pebax 1657) and hydrophilic/hydrophobic silica nanoparticles (0–10 wt%) were coated on a poly(vinyl chloride) (PVC) ultrafiltration membrane to form new mixed matrix composite membranes (MMCMs) for CO₂/N₂ separation. The membranes were characterized by SEM, FTIR, DSC and XRD. Successful formation of a non-porous defect-free dense top layer with ~4 μm of thickness and also uniform dispersion of silica nanoparticles up to 8 wt% loading in Pebax matrix were confirmed by SEM images. The gas permeation results showed an increase in the permeance of all gases and an increase in ideal CO₂/N₂ selectivity with the increase in silica nanoparticle contents. Comparison between the incorporation of hydrophilic and hydrophobic silica nanoparticle into Pebax matrix revealed that the great enhancement of CO₂ solubility is the key factor for the performance improvement of Pebax + silica nanoparticle membranes. The best separation performance of the hydrophilic silica nanoparticle-incorporated Pebax/PVC membrane for pure gases (at 1 bar and 25 °C) was obtained with a CO₂ permeability of 124 barrer and an ideal CO₂/N₂ selectivity of 76, i.e., 63 and 35% higher than those of neat Pebax membrane, respectively. The corresponding values for hydrophobic silica nanoparticle-incorporated Pebax/PVC membrane were 107 barrer for CO₂ permeability and 61 for ideal CO₂/N₂ selectivity. Also the performances of MMCMs improved upon pressure increase (1–10 bar) owing to the shift in plasticizing effect of CO₂ towards the higher pressures. In addition, an increase in permeabilities with a decrease in ideal selectivity was observed upon temperature increase (25–50 °C) due to the intensification of chain mobility.     

Antibacterial photocatalytic self‐cleaning poly(vinylidene fluoride) membrane for dye wastewater treatment

Membrane technology has been successfully applied for the removal of dyes from wastewater in the textile industry. A novel poly(vinylidene fluoride) (PVDF) membrane was prepared via blending with different dosages of Ag‐TiO₂‐APTES composite for dyeing waste water treatment in our study. And the effect of Ag‐TiO₂‐APTES blended into the PVDF membrane was discussed, including the rejection rate of methylene blue (MB) dye, membrane morphology, surface hydrophilicity, antibacterial activity, and a certain photocatalytic self‐cleaning performance. X‐ray diffraction and Fourier transform infrared characterization confirmed that Ag‐TiO₂ was functionalized by amount of hydroxyl group (−OH) and amino group (NH−), which provided by APTES. Contact angle measurement certified that the hydrophilicity of the membrane surface increased, with the contact angle decrease to 61.4° compared with 81.8° of original PVDF membrane. MB rejection rate was also increased to 90.1% after addition of Ag‐TiO₂‐APTES, and the rejection of original membrane was only 74.3%. The morphologies of membranes were observed by scanning electron microscope, which indicated that Ag‐TiO₂‐APTES had a good dispersion in membrane matrix and also improved the microstructure of membranes. Besides, UV irradiation experiments were performed on the composite films contaminated by MB, and the result showed that Ag‐TiO₂‐APTES nanoparticle provided PVDF membrane with a certain photodegradation capacity under UV irradiation. Moreover, antibacterial activity of the composite membrane was also demonstrated through antibacterial experiment, Escherichia coli as the representative bacteria. Perhaps, this research may provide a new way for PVDF blending modification.     

微乳液聚合耦合共混法构建聚偏氟乙烯共混杂化膜

以苯乙烯和甲基丙烯酸甲酯混合物作为油相, 采用反相微乳液法制备了AgCl纳米粒子; 通过微乳液原位聚合油相单体得到包含AgCl纳米粒子的聚合乳液; 将聚合乳液与聚偏氟乙烯(PVDF)通过共混法构建了包含AgCl纳米粒子的PVDF共混杂化膜. 紫外-可见光谱、 透射电子显微镜(TEM)及扫描电子显微镜(SEM)等表征结果和超滤实验结果表明, 聚合乳液加入的同时引入了亲水性聚合物和表面亲水的AgCl纳米粒子, 不仅改善了PVDF共混杂化膜的孔隙率和平均孔径, 还显著增强了PVDF共混杂化膜的极性和亲水性, 最终提升了膜的水通量和抗污染性能; 过量聚合乳液加入后不能与PVDF材料均匀共混, 而且AgCl纳米粒子也会在膜中形成团聚物堵塞膜孔隙, 从而削弱了膜的水通量和抗污染性能.     

Thermo-responsive and antifouling PVDF nanocomposited membranes based on PNIPAAm modified TiO2 nanoparticles

A novel hydrophilic nanocomposite additive(TiO2-g-PNIPAAm) was synthesized by the surface modification of titanium dioxide(TiO2) with N-isopropylacrylamide(NIPAAm) via "graft-from" technique. And the nanocomposite membrane of poly(vinylidene fluoride)(PVDF)/TiO2-g-PNIPAAm was fabricated by wet phase inversion. The graft degree was obtained by thermo-gravimetric analysis(TGA). Fourier transform infrared attenuated reflection spectroscopy(FTIR-ATR) and X-ray photoelectronic spectroscopy(XPS) characterization results suggested that TiO2-g-PNIPAAm nanoparticles segregated on membrane surface during the phase separation process. Scanning electron microscopy(SEM) was conducted to investigate the surface and cross-section of the modified membranes. The water contact angle measurements confirmed that TiO2-g-PNIPAAm nanoparticles endowed PVDF membranes better hydrophlilicity and thermo-responsive properties compared with those of the pristine PVDF membrane. The water contact angle decreased from 92.8° of the PVDF membrane to 61.2° of the nanocompostie membrane. Bovine serum albumin(BSA) static and dynamic adsorption experiments suggested that excellent antifouling properties of membranes was acquired after adding TiO2-gPNIPAAm. The maximum BSA adsorption at 40 °C was about 3 times than that at 23 °C. The permeation experiments indicated the water flux recover ratio and BSA rejection ratio were improved at different temperatures.     

Tailoring polyethersulfone/quaternary ammonium polysulfone ultrafiltration membrane with positive charge for dye and salt selective separation

Polyethersulfone (PES)/quaternary ammonium polysulfone (QAPSf) blend ultrafiltration (UF) membranes with positive charge were fabricated by nonsolvent induced phase separation (NIPS) for use in dye and salt selective separation. QAPSf was synthesized by nucleophilic substitution with chloromethylated polysulfone (CMPSf). The effect of the PES/QAPSf mass ratio on the morphology and performance of blend UF membranes were studied. The membranes' zeta potentials gradually changed from negative to positive with decreases in the PES/QAPSf mass ratio. At PES/QAPSf mass ratios of 30:70 and 10:90, the zeta potentials of the membranes reached +1.8 mV and + 5.9 mV, respectively. Additionally, the contact angles of the membranes decreased from 74° to 52° as the QAPSf content increased from 0 wt% to 90 wt%. Furthermore, the membrane with a PES/QAPSf mass ratio of 30:70 showed a high water permeance (181.4 LMH bar⁻¹) and excellent dye and salt selective separation performance. The rejection ratios reached 99.1%, 87.8%, 99.6%, and 92.4% for dyes Congo red, methyl blue, Alixin blue 8GX, and basic blue 24, respectively, while those for salts Na₂SO₄, MgSO₄, MgCl₂, and NaCl were ≤ 10%. In addition, the PES/QAPSf membranes showed excellent antifouling performance and good operating stability with dye-salt mixtures of various pHs and salt concentrations.     

Performance improvement of polysulfone ultrafiltration membrane by blending with polyaniline nanofibers

Polyaniline (PANI) nanofibers were used to improve hydrophilic property and permeability of polysulfone (PS) membrane. PS membrane and PS/PANI nanofibers blended membranes with different PANI–PS mass ratios (1, 5, 10, and 15 wt.%) were prepared by phase inversion process. The blended membranes showed similar bovine serum albumin (BSA) and albumin egg (AE) rejections to PS membrane. The blended membranes had larger porosity and better hydrophilic property than PS membrane, which caused the improvement of their permeability. Pure water fluxes of the blended membranes with PANI–PS mass ratios of 1 and 15 wt.% were 1.6 and 2.4 times that of PS membrane, respectively. During the filtration of BSA solution, the blended membranes had slower flux decline rate than PS membrane. Moreover, stable permeate fluxes of the blended membranes with PANI–PS mass ratios of 1 and 15 wt.% were 2.0 and 2.5 times that of PS membrane, respectively. Compared with PS membrane, mechanical property and thermal stability of the blended membranes with less PANI–PS mass ratio, e.g. 1 wt.%, had no obvious change. For the blended membrane with PANI–PS mass ratio of 15 wt.%, breaking strength increased 28% and elongation at break decreased 30.6%.     

Polyaniline decorated graphene oxide on sulfonated poly(ether ether ketone) membrane for direct methanol fuel cells application

In direct methanol fuel cells (DMFC), methanol crossover is a major issue which has reduced the performance of polymer electrolyte membrane (PEM) for energy generation. In this study, graphene oxide (GO) and conductive polyaniline decorated GO (PANI-GO) were used as additives in fabrication of sulfonated poly(ether ether ketone) (SPEEK) nanocomposite PEM membrane to reduce methanol crossover. PANI-GO was synthesized by in situ polymerization method and the formation of PANI coated GO nanostructures was confirmed by surface morphology and crystallinity analysis. The membrane morphology and topography analysis confirmed that GO and PANI-GO were well dispersed on the surface of SPEEK membrane. 0.1 wt% PANI-GO modified SPEEK nanocomposite membrane exhibited the highest water uptake and ion exchange capacity of 40% and 1.74 meq g^?1, respectively. The oxidative stability of the nanocomposite membranes also improved. Lower methanol permeability of 4.33 × 10^?7 cm^?2S^?1 was noticed for 0.1 wt% PANI-GO modified SPEEK membrane. PANI-GO modified SPEEK membrane enhanced the proton conductivity, which was due to the existence of acidic and hydrophilic group present in PANI and GO. PANI-GO modified SPEEK membrane held higher selectivity of 1.94 × 10⁴ S cm^?3 s^?1. Overall, these studies revealed that PANI-GO modified SPEEK membrane is a potential material for DMFC applications.