Mussel‐inspired decoration of Ni(OH)2 nanosheets on 2D MoS2 towards enhancing thermal and flame retardancy properties of poly(lactic acid)

In the present work, a facile and environmental method was developed to fabricate the novel functionalized MoS₂ hybrid. Firstly, MoS₂ nanosheets were coated with polydopamine (PDA) through the self‐polymerization of dopamine (MoS₂‐PDA) in a buffer solution. Then the decoration of Ni(OH)₂ on the MoS₂‐PDA was synthesized because of the strong affinity of Ni²⁺ with hydroxyl groups in PDA. Finally, the as‐synthesized MoS₂‐PDA@Ni(OH)₂ was introduced into poly(lactic acid) (PLA) matrix to explore flame retardancy, thermal stability, and crystalline property of the composites. As confirmed by X‐ray diffraction (XRD), Fourier‐transform infrared spectrometer (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA), the MoS₂ nanosheets were dually modified with PDA and Ni(OH)₂ without destroying the original structures. The thermal degradation of PLA with MoS₂‐PDA@Ni(OH)₂ generated a notably higher yield of char. Moreover, the crystallization rate of composites is higher than neat PLA. The cone calorimeter test revealed that the introduction of 3% MoS₂‐PDA@Ni(OH)₂ resulted in lower Peak Heat Release Rate (PHRR) (decreased by 21.7%). Thus, the research provided an innovative functionalization method for manufacturing PLA composites with high performances.     

The influence of different fillers on mechanical and physical properties of high-molecular-weight biodegradable aliphatic polyesters

Poly(ethylene succinate) and poly(butylene succinate) are synthetic biodegradable polymers, and much attention is paid to study the properties of pure polymers and the polymers modified by different comonomers and filling materials. The literature data on the physical properties of these polymers vary widely depending on their method of preparation and subsequent modifications. Most of the studies deal with low- and moderate-molecular-weight polymers or commercial grade polymers, modified by different comonomers and chain-extension agents. The data on pure high-molecular-weight polymers are scarce. In this work, we have prepared high-molecular-weight (MW range of (1.4–1.8) × 10⁵) poly(ethylene succinate) and poly(butylene succinate) by direct polycondensation at 200°C in a nitrogen flow without chain-extension agents. We have further studied the properties of pure polymers and examined the effect of different fillers (carbon nanotubes, SiO₂, Aerosil®) on the mechanical and physical properties of these polymers. Because of high-molecular-weight, the polymers possess increased tensile and storage moduli and thermostability. Even very low filler contents (up to 1 wt %) have a pronounced influence on the polymer properties: the polymer tensile and the storage modulus increases, the elongation at break decreases, and the thermal stability of the polymers decreases slightly. The effects of fillers are less pronounced compared with those for low- and moderate-molecular-weight polymers. When mixed together, poly(ethylene succinate) and poly(butylene succinate) crystallize independently from each other as evident from the mechanical and thermal analysis data.     

Processable and Robust MoS2 Paper Chemically Cross‐Linked with Polymeric Ligands by the Coordination of Divalent Metal Ions

Inorganic graphene analogues (IGAs) are a huge and fascinating family of compounds that have extraordinary electronic, mechanical, and thermal properties. However, one of the largest problems that face the industrial application of IGAs is their poor processability, which has led to a “bottlenecking” in the development of freestanding, large‐area, IGA‐based thin‐film devices. Herein, we report a facile and cost‐efficient method to chemically modify IGAs by using their abundant coordination atoms (S, O, and N). Taking MoS₂ as an example, we have prepared homogeneous “solution” systems, in which MoS₂ nanosheets are chemically cross‐linked through a carboxylate‐containing polymeric ligand, poly(methyl methacrylate) (PMMA), by copper‐ion coordination. Bonding interactions between C?O bonds and sulfur atoms through copper ions were confirmed by various characterization techniques, such as UV/Vis, FTIR, and Raman spectroscopy and XPS. By using our method, freestanding MoS₂ paper with significantly improved mechanical properties was obtained, thus laying the basis for the mass production of large‐area MoS₂‐based thin‐film devices. Furthermore, copper‐ion coordination was also applied to MoS₂/PMMA nanocomposites. Direct and strong nanofiller/matrix bonding interactions facilitate efficient load transfer and endow the polymeric nanocomposites with an excellent reinforcement effect. This method may pave a new way to high‐strength polymeric nanocomposites with superior frictional properties, flame retardance, and oxidation resistance.     

Selective modification of two-dimensional MoS2 nanosheets by polymer grafting

We reported on the direct creation of polymer brushes on two-dimensional molybdenum disulfide via the formation of C-S bond by UV-induced photopolymerization. The functionalization can be manipulated in forming polymer grafts on one side or both sides of the nanosheets.     

Improving the gas barrier,mechanical and thermal properties of poly(vinyl alcohol) with molybdenum disulfide nanosheets

New multifunctional materials with both high structural and gas barrier performances are important for a range of applications. Herein we present a one‐step mechanochemical process to prepare molybdenum disulfide (MoS₂) nanosheets with hydroxy functional groups that can simultaneously improve mechanical strength, thermal conductivity, and gas permittivity of a polymer composite. By homogeneously incorporating these functionalized MoS₂ nanosheets at low loading of less than 1 vol %, a poly(vinyl alcohol) (PVA) polymer exhibits elongation at break of 154%, toughness of 82 MJ/m³, and in‐plane thermal conductivity of 2.31 W/m K. Furthermore, this composite exhibits significant gas barrier performance, reducing the permeability of helium by 95%. Under fire condition, the MoS₂ nanosheets form thermally stable char, thus enhancing the material's resistance to fire. Hydrogen bonding has been identified as the main interaction mechanism between the nanofillers and the polymer matrix. The present results suggest that the PVA composite reinforced with 2D layered nanomaterial offers great potentials in packaging and fire retardant applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 406–414     

High-efficiency electrodeposition of polyindole nanocomposite using MoS2 nanosheets as electrolytes and their capacitive performance

Polyindole (PIn) has attracted extensive interest as promising energy storage materials owing to fairly good thermal stability, high redox activity and stability, however, it is challenging to prepare high-quality PIn in neutral solvents by electrochemical method. Herein, a simple route, based on MoS₂ nanosheets as electrolytes, has been developed for the electrochemical preparation of PIn/MoS₂ nanocomposite in acetonitrile solution. Due to the coordination interaction between indole and MoS₂, the onset oxidation potential of indole in this medium was reduced to 0.5 V from 0.75 V determined in acetonitrile/LiClO₄. The morphologies and structures of as-obtained PIn/MoS₂ nanocomposite were characterized using SEM, TEM, XRD, Raman and XPS. The results of thermal analysis indicated that the PIn/MoS₂ nanocomposite had an improved thermal stability relative to PIn and MoS₂ nanosheets. Moreover, the specific capacitance of PIn/MoS₂ nanocomposite was 8.3 times higher than that of PIn prepared acetonitrile/LiClO₄. To the best of our knowledge, this is the first report on the high-efficiency electrodeposition of PIn/MoS₂ nanocomposite in MoS₂-based acetonitrile solution, which will be a promising candidate as a high efficient electrode material in the application of supercapacitors.     

利用光热电效应收集近红外光能的二硫化钼和热释电高分子纳米复合物

设计合成了一种基于二硫化钼（MoS₂）/热释电聚合物的柔性薄膜光热电纳米发电机（PTENG）。过渡金属硫族化合物作为薄层纳米薄片,可以捕获近红外（NIR）光,并将其转化为热能。同时,热释电聚合物将无机纳米片所收集的热能转化为电能。在近红外辐照下,PTENG可以瞬间产生电压和光电流,且输出长期保持在较高水平。通过光热效应与热释电效应的有效耦合,该体系具有较高的热电转换系数。我们还通过理论模拟分析了MoS₂在聚合物纳米复合材料中的作用。MoS₂的存在显著提高了热释电聚合物薄膜的温度变化率,提高了器件的光电响应。     

A glassy carbon electrode modified with MoS<Subscript>2</Subscript> nanosheets and poly(3,4-ethylenedioxythiophene) for simultaneous electrochemical detection of ascorbic acid,dopamine and uric acid

We describe a chemical exfoliation method for the preparation of MoS₂ nanosheets. The nanosheets were incorporated into poly(3,4-ethylenedioxythiophene) (PEDOT) by electrodeposition on a glassy carbon electrode (GCE) to form a nanocomposite. The modified GCE is shown to enable simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to the synergistic effect of MoS₂ and PEDOT, this electrode displays better properties in terms of electrocatalytic oxidation of AA, DA and UA than pure PEDOT, which is illustrated by cyclic voltammetry and differential pulse voltammetry (DPV). Under optimum conditions and at pH 7.4, the respective sensitivities and best working potentials are as follows: AA: 1.20 A?mM^?1?m^?2, 30 mV; DA: 36.40 A?mM^?1?m^?2, 210 mV; UA: 105.17 A?mM^?1?m^?2, 350 mV. The calculated detection limits for AA, DA and UA are 5.83 μM, 0.52 μM and 0.95 μM, respectively. The modified electrode was applied to the detection of the three species in human urine samples and gave satisfactory results.

Open image in new window

Graphical abstract MoS₂ nanosheets were prepared by a facile chemical exfoliation method. MoS₂ and poly(3,4-ethylenedioxythiophene) nanocomposite modified glassy carbon electrodes were fabricated, which are shown to enable simultaneous determination of ascorbic acid, dopamine and uric acid with high sensitivity and selectivity.

     

Effects of comonomer sequential structure on thermal and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)s

In this work, new investigations on the effect of comonomer sequential structure on the thermal and crystallization behaviors and biodegradability have been implemented for the biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST) as well as aliphatic poly(butylene succinate) (PBS). At first, these copolyesters were efficiently synthesized from dimethyl succinate and/or dimethyl terephthalate and 1,4‐butanediol via condensation polymerization in bulk. Subsequently, their molecular weights and macromolecular chain structures were analyzed by gel permeation chromatography (GPC) and nuclear magnetic resonance (NMR) spectroscopy. By means of differential scanning calorimeter (DSC) and wide‐angle X‐ray diffractometer (WAXD), thermal and crystallization behaviors of these synthesized aromatic–aliphatic copolyesters were further explored. It was demonstrated that the synthesized copolyesters were revealed to have random comonomer sequential structures with thermal and crystallization properties strongly depending on their comonomer molar compositions, and that crystal lattice structures of the new crystallizable copolyesters shifted from the monoclinic crystal of semicrystalline PBS to triclinic lattice of the poly(butylene terephthalate) (PBT) with increasing the terephthalate comonomer composition, and the minor comonomer components were suggested to be trapped in the crystallizable component domains as defects. In addition, the enzymatic degradability was also characterized for the copolyesters film samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1635–1644, 2006     

Prediction of CO2 Solubility in Polymers by Radial Basis Function Artificial Neural Network Based on Chaotic Self-adaptive Particle Swarm Optimization and Fuzzy Clustering Method

To replace costly and time-consuming experimentation in laboratory, a novel solubility prediction model based on chaos theory, self-adaptive particle swarm optimization （PSO）, fuzzy c-means clustering method, and radial ba- sis function artificial neural network （RBF ANN） is proposed to predict CO2 solubility in polymers, hereafter called CSPSO-FC RBF ANN. The premature convergence problem is overcome by modifying the conventional PSO using chaos theory and self-adaptive inertia weight factor. Fuzzy c-means clustering method is used to tune the hidden centers and radial basis function spreads. The modified PSO algorithm is employed to optimize the RBF ANN connection weights. Then, the proposed CSPSO-FC RBF ANN is used to investigate solubility of CO2 in polystyrene （PS）, polypropylene （PP）, poly（butylene succinate） （PBS） and poly（butylene succinate-co-adipate） （PBSA）, respec- tively. Results indicate that CSPSO-FC RBF ANN is an effective method for gas solubility in polymers. In addition, compared with conventional RBF ANN and PSO ANN, CSPSO-FC RBF ANN shows better performance. The values of average relative deviation （ARD）, squared correlation coefficient （R2） and standard deviation （SD） are 0.1071, 0.9973 and 0.0108, respectively. Statistical data demonstrate that CSPSO-FC RBF ANN has excellent prediction capability and high-accuracy, and the correlation between prediction values and experimental data is good.     

Hierarchical MoS2@TiO2 Heterojunctions for Enhanced Photocatalytic Performance and Electrocatalytic Hydrogen Evolution

Hierarchical MoS₂@TiO₂ heterojunctions were synthesized through a one‐step hydrothermal method by using protonic titanate nanosheets as the precursor. The TiO₂ nanosheets prevent the aggregation of MoS₂ and promote the carrier transfer efficiency, and thus enhance the photocatalytic and electrocatalytic activity of the nanostructured MoS₂. The obtained MoS₂@TiO₂ has significantly enhanced photocatalytic activity in the degradation of rhodamine B (over 5.2 times compared with pure MoS₂) and acetone (over 2.8 times compared with pure MoS₂). MoS₂@TiO₂ is also beneficial for electrocatalytic hydrogen evolution (26 times compared with pure MoS₂, based on the cathodic current density). This work offers a promising way to prevent the self‐aggregation of MoS₂ and provides a new insight for the design of heterojunctions for materials with lattice mismatches.     

High-performance supercapacitor electrode based on a nanocomposite of polyaniline and chemically exfoliated MoS<Subscript>2</Subscript> nanosheets

In this study, MoS₂ nanosheets were first prepared by exfoliating its bulk material in HCl/LiNO₃ solution with a yield of 45%, and then a facile strategy was developed to synthesize polyaniline/MoS₂ (PANI/MoS₂) nanocomposite via in situ polymerization. Structural and morphological characterizations of MoS₂ nanosheets and the nanocomposite were investigated by scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray powder diffraction. The results of SEM illustrated that orderly sawtooth polyaniline (PANI) nanoarrays were formed on the surface of MoS₂ nanosheets. The nanocomposite displayed good electrochemical performance as a supercapacitor electrode material. The specific capacitance reached 560 F/g at a current density of 1.0 A g^?1 in 1.0 M H₂SO₄ solution. Such good performance is because that the MoS₂ nanosheets provided a highly electrolytic accessible surface area for redox-active PANI and a direct path for electrons.     

The effect of polymer-substrate interaction on the nucleation property: Comparing study of graphene and hexagonal boron nitride Nanosheets

Hexagonal boron nitride nanosheets (BNNSs) can work as a more efficient nucleating agent for two polyesters compared to graphene. Studies on the crystallization and dewetting processes of two polyesters, poly(butylene succinate) and poly(butylene adipate), on the two substrate surfaces prove that the interaction between BNNSs and the polyesters is stronger than that between graphene and the polyesters. This strong interaction induces the pre-ordered conformation of molten PBA which has been identified by the in situ FTIR spectra. Thus BNNSs possess higher nucleation property than graphene. Finally, a new polymer-substrate interaction induced nucleation mechanism was proposed to explain the nucleation efficiency difference between graphene and BNNSs.     

Defect Engineering of Two-Dimensional Molybdenum Disulfide

Two-dimensional (2D) molybdenum disulfide (MoS₂) holds great promise in electronic and optoelectronic applications owing to its unique structure and intriguing properties. The intrinsic defects such as sulfur vacancies (SVs) of MoS₂ nanosheets are found to be detrimental to the device efficiency. To mitigate this problem, functionalization of 2D MoS₂ using thiols has emerged as one of the key strategies for engineering defects. Herein, we demonstrate an approach to controllably engineer the SVs of chemically exfoliated MoS₂ nanosheets using a series of substituted thiophenols in solution. The degree of functionalization can be tuned by varying the electron-withdrawing strength of substituents in thiophenols. We find that the intensity of 2LA(M) peak normalized to A_1g peak strongly correlates to the degree of functionalization. Our results provide a spectroscopic indicator to monitor and quantify the defect engineering process. This method of MoS₂ defect functionalization in solution also benefits the further exploration of defect-free MoS₂ for a wide range of applications.     

An efficient halogen-free flame retardant for glass-fibre-reinforced poly(butylene terephthalate)

Compared with poly(butylene terephthalate) (PBT), glass-fibre-reinforced poly(butylene terephthalate) (GF-PBT) is difficult to flame retard with halogen-free flame retardants. In the present study, the aluminium salt of hypophosphorous acid (AP) was used as a flame retardant for GF-PBT. A series of flame-retardant GF-PBT composites was prepared via melt compounding. The flame retardance and combustion behaviour of the composites were studied by limiting oxygen index (LOI), vertical burning test (UL-94) and cone calorimetric test. Thermal behaviours and thermal decomposition kinetics were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. The addition of AP to the composites could result in an increased LOI value, a UL-94 V-0 (1.6 mm) classification and a better fire performance in cone calorimetric tests. The char morphology observation after flame-retardant tests, calculation of decomposition kinetics, X-ray photoelectron spectroscopy (XPS) and infra-red spectral analysis of the char residue confirmed the condensed-phase flame-retardant mechanism. Furthermore, the mechanical properties of the flame-retardant composites were not deteriorated, retaining an acceptable level.     

Side‐Chain‐Directed Dispersion of MoS2 Nanosheets by V‐Shaped Polyaromatic Compounds

Bulk molybdenum disulfide (MoS₂) itself is virtually insoluble in common organic solvents because of the tight stacks of multiple MoS₂ nanosheets. Here we report that V‐shaped polyaromatic compounds with non‐ionic side chains can efficiently exfoliate and disperse the inorganic nanosheets. Simple grinding and sonication (less than total 1 h) of MoS₂ powder with the V‐shaped compounds gave rise to large MoS₂ nanosheets highly dispersed in NMP through efficient host‐guest S–π interactions. DLS and AFM analyses revealed that the lateral sizes (ca. 150–270 nm) and thicknesses (ca. 2–8 nm) of the products depend on the identity of the non‐ionic side chains on the V‐shaped dispersant.     

Preparation of MoS2‐graphene Hybrid Nanosheets and Simultaneously Electrochemical Determination of Levodopa and Uric Acid

MoS₂ nanoflakes were prepared by exfoliating commercial MoS₂ powders with the assistance of ultrasound and graphene foam was synthesized by chemical vapor deposition using nickel foam as the template. MoS₂‐graphene hybrid nanosheets were developed through the combination of MoS₂ nanoflakes and graphene nanosheets by ultrasonic dispersion. The hybrid nanosheets were sprayed onto the ITO coated glass, which acts as an electrode for the simultaneously electrochemical determination of levodopa and uric acid. The MoS₂‐graphene hybrid nanosheets were characterized by scanning electron microscopy, X‐ray diffraction and Raman spectroscopy. The results show that the hybrid nanosheets are composed of MoS₂ and graphene with a sheet‐like morphology. The sensitivity of the electrode for levodopa and uric acid is 0.36 μA μM⁻¹ and 0.39 μA μM⁻¹, respectively. The electrode also shows low limit of detection, good selectivity, reproducibility and stability. And it is potential for use in clinical research.     

Free‐standing and Flexible MoS2/rGO Paper Electrode for Amperometric Detection of Folic Acid

The development of flexible electrodes is of considerable current interest because of the increasing demand for modern electronics, portable medical products, and compact devices. We report a new type of flexible electrochemical sensor fabricated by integrating graphene and MoS₂ nanosheets. A highly flexible and free‐standing conductive MoS₂ nanosheets/reduced graphene oxide (MoS₂/rGO) paper was prepared by a two‐step process: vacuum filtration and chemical reduction treatment. The MoS₂/graphene oxide (MoS₂/GO) paper obtained by a simple filtration method was transformed into MoS₂/rGO paper after a chemical reduction process. The obtained MoS₂/rGO paper was characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy, electrochemical impedance spectroscopy. The electrochemical behavior of folic acid (FA) on MoS₂/rGO paper electrode was investigated by cyclic voltammetry and amperometry. Electrochemical experiments indicated that flexible MoS₂/rGO composite paper electrode exhibited excellent electrocatalytic activity toward the FA, which can be attributed to excellent electrical conductivity and high specific surface area of the MoS₂/rGO paper. The resulting biosensor showed highly sensitive amperometric response to FA with a wide linear range.     

Chain extension of adipic acid and (or) succinic acid/butanediol polyesters with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) and adipoylbiscaprolactamate combined chain extenders

This paper provided an easy and flexible method to synthesize high molecular weight polyesters by polycondensation and chain extension. Low molecular weight polybutylene adipate, polybutylene succinate, and poly(butylene succinate‐co‐butylene adipate) (PBSA) were synthesized through melt condensation polymerization from adipic acid and/or succinic acid with butanediol. The prepolyesters obtained had different amount of ? COOH and ? OH terminal groups. Chain extension of them was carried out at 180–240°C using 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) and adipoyl biscaprolactamate as combined chain extenders. The influencing factors of the chain extension were studied. At the optimal conditions, chain‐extended polybutylene adipate with M_n up to 39,100, polybutylene succinate with intrinsic viscosity of 0.99 dl/g, and PBSA with intrinsic viscosity from 0.73 to 0.81 dl/g were synthesized. The chain‐extended polyesters were characterized by IR spectrum, ¹H NMR spectrum, differential scanning calorimetry, thermogravimetric analysis (TGA), wide angle X‐ray scattering, and tensile test. The thermal analysis showed that chain extension often led to slight decrease of the regularity, the crystallinity, and the melting point. This deterioration of the properties is not harmful enough to impair their thermal properties and obstruct them from being used as biodegradable thermoplastics. The TGA showed that the chain‐extended polyesters were stable with initial decomposition temperature over 354.7°C. The tensile strength of the chain extended PBS and PBSAs with butylene adipate units less than 20 mol% was in the range of 18.95–31.22 MPa. Copyright © 2010 John Wiley & Sons, Ltd.     

MoS2 as a Co-Catalyst for Photocatalytic Hydrogen Production: A Mini Review

Molybdenum disulfide (MoS₂), with a two-dimensional (2D) structure, has attracted huge research interest due to its unique electrical, optical, and physicochemical properties. MoS₂ has been used as a co-catalyst for the synthesis of novel heterojunction composites with enhanced photocatalytic hydrogen production under solar light irradiation. In this review, we briefly highlight the atomic-scale structure of MoS₂ nanosheets. The top-down and bottom-up synthetic methods of MoS₂ nanosheets are described. Additionally, we discuss the formation of MoS₂ heterostructures with titanium dioxide (TiO₂), graphitic carbon nitride (g-C₃N₄), and other semiconductors and co-catalysts for enhanced photocatalytic hydrogen generation. This review addresses the challenges and future perspectives for enhancing solar hydrogen production performance in heterojunction materials using MoS₂ as a co-catalyst.