首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
以自制的松香改性酚醛环氧树脂(RPAE)为对象,采用差示扫描量热法研究了其与4,4.二氨基二苯砜组成的体系(RPAE/DDS)的固化动力学,利用Kissinger方程计算得到体系的固化热约为109.29J/g,表观活化能为51.56kJ/mol,该体系反应级数为0.85,近似为1级反应,反应速率常数为2.69×10^4/s。采用Ozawa-Flynn-Wall方程分析,得到体系的表观活化能为70。1kJ/mol。  相似文献   

2.
利用自制的有机蒙脱土 ,采用浇模固化成型法制备酚醛树脂 /六次甲基四胺 /蒙脱土纳米复合材料 ,并用XRD观察有机蒙脱土分别在热塑性和热固性酚醛树脂中复合行为 .研究发现 ,由于两种树脂的固化反应机理不同 ,热固性酚醛树脂与蒙脱土复合 ,可得插层型纳米复合材料 ;而采用热塑性酚醛树脂进行固化 ,则得到部分剥离的纳米复合材料 .通过DSC进一步研究热塑性酚醛树脂 /蒙脱土复合体系的固化反应动力学 .运用Kissinger ,Flynn Wall Ozawa ,Crane方法求出活化能和反应级数等动力学参数 .结果发现 ,加入蒙脱土使固化反应活化能下降 ,反应级数减小 ,从而有利于固化工艺的实现 ,便于纳米复合材料实际应用 .  相似文献   

3.
The curing mechanisms and kinetics of diglycidyl ether of bisphenol A with diethylenetriamine as the curing agent and different amounts of organic montmorillonite were examined with isothermal and dynamic scanning calorimetry. The modified Avrami equation was used to calculate the activation energy and reaction orders in the isothermal experiment. A single peak was observed in each dynamic scan. The curing mechanism and kinetics of the curing reaction were also analyzed by two kinds of methods—Kissinger and Flynn–Wall–Ozawa. The results obtained from those methods under dynamic measurement agreed with those obtained from the modified Avrami equation. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 378–386, 2003  相似文献   

4.
双酚-S环氧树脂与琥珀酸酐固化反应动力学   总被引:5,自引:0,他引:5  
用差示扫描量热法(DSC)研究了双酚-S环氧树脂(BPSER)与琥珀酸酐固化反应的历程。实验结果表明,固化反应主要分两个阶段,前期由化学动力学控制,服从自催化机理。实验数据利用Kamal方程处理得到两个速率常数k、、k2及两个反应级数m、n、k1、k2的值随反应温度的升高呈增大的趋势,总反应级数m+n在2~2.5之间,当转化率达到40%左右后,由于交联程度增加,分子量迅速增长,分子间扩散较慢,进入  相似文献   

5.
BMD/UP体系非等温固化动力学研究   总被引:1,自引:0,他引:1  
不饱和聚酯是最常用的一种热固性材料,其力学性能和耐热性是较受关注的两个方面,利用双马来酰亚胺作为第二组分对不饱和聚酯进行耐热改性的工作取得了较好的效果。研究其动力学过程对于固化反应温度、时间等工艺合理优化控制,制备高性能复合材料具有重要意义。考虑到BMD/UP体系中反应的复杂性,本文采用n级动力学模型,进行了非等温动力学研究。  相似文献   

6.
Activation energy for the curing process of epoxy glass mica tape has been experimentally determined from differential scanning calorimetric measurements and found to be 20 kcal/ mol. Thermochemical calculation shows that the rate controlling step is the dissociation of the C-O bond in the epoxide leading to ring opening and its subsequent reaction with amine hardener. Shelf life has been determined from the measurement of the enthalpy loss corresponding to the curing during the aging process. The kinetics of the aging process also yields an activation energy of 20 kcal/mol which corresponds to the slow curing of the epoxy resin.  相似文献   

7.
An experimental study was carried out to investigate the effect of ethylene glycol dimethacrylate (EGDMA, as a crosslinking agent) content on the curing kinetics of the polymerization of 2-hydroxyethyl methacrylate (HEMA), using differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR). EGDMA may cause a crosslinking-facilitated gel effect which reduces the termination rate of living free radicals and enhances the overall reaction rate, but it may also induce a diffusional resistance for the reactants so that some free monomers are trapped and pendant vinyl groups are prohibited from reaction by the crosslinked structure. At higher content of EGDMA, the later effect becomes predominant, and the reaction rate and the final conversion are limited. The exothermic peak of the curing reaction tends to carry a shoulder and then split into two peaks as the amount of EGDMA is increased, possibly due to a later reaction of the trapped monomers and pendant vinyls. The heat of reaction measured by DSC in the scanning mode is 61.2 kJ/mol CC. The activation energy (E) of the curing reaction ranges from 56.5 to 78.3 kJ/mol CC depending on the EGDMA content and the type of operation. The diffusion-limited reaction rate and the different thermal history experienced in the nonisothermal and isothermal curing can result in variations of the results in the activation energy measurement. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 1873–1889, 1997  相似文献   

8.
Adsorption of Ni(II) on clays   总被引:1,自引:0,他引:1  
The present work investigates the adsorptive interactions of Ni(II) ions with kaolinite, montmorillonite, and their poly(oxo zirconium) and tetrabutylammonium derivatives in aqueous medium. Batch adsorption studies were carried out with various Ni(II) concentrations, amount of clay adsorbents, pH, agitation time and temperature. The adsorption is strongly dependent on pH of the medium with enhanced adsorption as the pH turns from acidic to alkaline side till precipitation sets in. The process was very fast initially and maximum adsorption was observed within 180 min of agitation. The kinetics of the interactions, tested with pseudo first order Lagergren equation, second order kinetics, Elovich equation, liquid film diffusion model and intra-particle diffusion mechanism, showed better agreement with second order kinetics (k2 = 1.3 x 10(-2) to 5.3 x 10(-2) g/(mg min)). The adsorption data gave good fits with Langmuir and Freundlich isotherms and yielded Langmuir monolayer capacity of 2.75 to 21.14 mg/g and Freundlich adsorption capacity of 0.70 to 3.40 mg(1-1/n) l(1/n)/g for the clay adsorbents. The adsorption process was exothermic with Delta H in the range of -24.0 to -45.1 kJ/mol accompanied by decrease in entropy (DeltaS: -118.2 to -160.5 J/(mol K)) and Gibbs energy (Delta G: -34.6 to -49.5 kJ/mol). The results have shown that montmorillonite has the largest adsorption capacity followed by ZrO-montmorillonite, TBA-montmorillonite, kaolinite, ZrO-kaolinite and TBA-kaolinite. Introduction of ZrO- and TBA- groups into the clays reduced their adsorption capacity by blocking the available adsorption sites.  相似文献   

9.
酸酐固化环氧树脂/蒙脱土复合材料的等温固化动力学   总被引:5,自引:0,他引:5  
用等温差示扫描量热法(DSC)研究了酸酐固化环氧树脂/蒙脱土复合材料的等温固化过程,考察了未处理的蒙脱土(MMT)和有机蒙脱土(OMMT)对环氧树脂固化动力学的影响. 实验表明, 环氧树脂的固化过程包含自催化机理,加入蒙脱土没有改变固化反应机理. 用Kamal方程对该体系的固化过程进行拟合,得到反应级数m、n,反应速率常数k1、k2,总反应级数(m + n)在2.4~3.0之间. MMT的加入使环氧树脂体系的k1、k2有所降低,而OMMT的加入对体系的k1、k2影响较为复杂,加入蒙脱土对环氧树脂固化体系的活化能影响较小.  相似文献   

10.
In the present study, the reaction kinetics of polybutylene terephthalate (PBT) and epoxy system was studied by a novel rheological method. The reaction process was determined by rheological test and the results showed that there were three stages in the reaction between PBT and epoxy, which were reaction-controlling stage (stage I), reaction-stagnation stage (stage II) and diffusion-controlling stage (stage III). In addition, the stage I was selected to study the reaction kinetics by the rheological method. The results showed that the reaction between PBT and epoxy could be classified as a pseudo-first-order reaction due to the excessive amount of epoxy group. Furthermore, the reaction apparent activation energy of the stage I determined by the rheological method was 143 kJ/mol. To confirm these results, the reaction kinetics was also evaluated by the endgroup determination method, and the results showed that the reaction could also be classified as a pseudo-first-order reaction. Moreover, the apparent activation energy of the reaction was 116 kJ/mol, which was similar to that of the value obtained by the rheological method.  相似文献   

11.
1-己基-3-甲基咪唑四氯化铁盐固化环氧树脂E-51的反应特性   总被引:1,自引:1,他引:0  
采用差示扫描(DSC)量热分析法研究了1-己基-3-甲基咪唑四氯化铁离子液体([C6mim]FeCl4)与双酚A型环氧树脂E-51的固化反应。结果显示,由于[C6mim]FeCl4包含多级胺基结构,因此可以作为E-51的高温固化剂使用,其与E-51的反应包含两个阶段:第一个阶段的反应放热峰峰顶温度约在120 ℃,第二个阶段的反应放热峰峰顶温度会随着[C6mim]FeCl4用量的增加而发生变化。当[C6mim]FeCl4与混合胺复配成新型固化剂时,二者产生明显的协同效应。通过恒温DSC实验发现,复配体系与E-51的固化反应可以在室温下发生,表现为在30 ℃固化反应放热峰峰顶放热时间为5 min左右,且随着恒温固化反应温度的提高,峰顶放热峰时间会缩短。非等温动力学结果显示:复配体系与E-51的反应活化能为979 J/mol,仅是混合胺体系的17%左右。反应级数为0.5表明这一固化反应是无规反应。  相似文献   

12.
环氧树脂/桐油酸酐/蒙脱土纳米复合材料固化动力学   总被引:6,自引:0,他引:6  
环氧树脂/桐油酸酐/蒙脱土纳米复合材料固化动力学;固化反应;DSC  相似文献   

13.
氮丙啶交联剂的交联性能及固化动力学研究   总被引:10,自引:0,他引:10  
谢飞  刘宗惠  魏德卿 《合成化学》2002,10(2):120-125
合成了一种氯丙啶交联剂,并以丙烯酸树脂乳液为模型化合物对交联剂的交联性能及固化动力学进行了研究。结果表明:在丙烯酸树脂乳液中加入适量的氯丙啶交联剂,可使胶膜的力学性能及耐水碱性,耐溶剂性都得到很大的提高;但交联对玻璃化转变温度的影响较小。用程序升温DSC(差示扫描量热法)方法对固化反应动力学进行了研究,计算出固化反应的活化能。  相似文献   

14.
The curing kinetics of a novel liquid crystalline epoxy resin with combining biphenyl and aromatic ester‐type mesogenic unit, diglycidyl ether of 4,4′‐bis(4‐hydroxybenzoyloxy)‐3,3′,5,5′‐tetramethyl biphenyl (DGE‐BHBTMBP), and the curing agent diaminodiphenylsulfone (DDS) was studied using the advanced isoconvensional method (AICM). DGE‐BHBTMBP/DDS curing system was investigated the curing behavior by means of differential scanning calorimetry (DSC) during isothermal and nonisothermal processes. Only one exothermal peak appeared in isothermal DSC curves. A variation of the effective activation energy with the extent of conversion was obtained by AICM. Three different curing stages were confirmed. In the initial curing stage, the value of Ea is dramatically decreased from ~90 to ~20 kJ/mol in the conversion region 0–0.2 for the formation of LC phase. In the middle stage, the value of Ea keeps about ~80 kJ/mol for cooperative effect of reaction mechanism and diffusion control. In the final stage, a significant increase of Ea from 84 to 136 kJ/mol could be caused by the mobility of longer polymer chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3922–3928, 2007  相似文献   

15.
The curing kinetics of nanocomposites based on phenolic resol cured with triethylamine (TEA) containing different amounts of organic montmorillonite was analyzed by differential scanning calorimetry. Kissinger-Akahira-Sunose (KAS) model-free kinetics has been applied to correlate the dynamic cure behaviour in the presence of modified montmorillonite. The effect in the curing of the use of different clay modifiers has also been studied. A commercial clay with hydroxyl groups (Cloisite 30B) and a customized montmorillonite (PheMMT) whose reactive groups induce condensation reactions with the resol matrix have been used. Strong dependency of activation energy on apparent conversion has been observed for all compounds.  相似文献   

16.
几种聚醚胺改性蒙脱土对环氧树脂固化过程的影响   总被引:1,自引:0,他引:1  
段轶锋  王小群  刘羽中  杜善义 《化学学报》2012,70(10):1179-1186
首先制备了五种聚醚胺改性蒙脱土(MMT), 并将这五种聚醚胺改性蒙脱土加入到双酚A 型环氧树脂E51 和聚醚胺D400体系中, 采用差示扫描量热法(DSC)考察了五种聚醚胺改性MMT对环氧树脂升温固化进程的影响. 随后, 优选一种EP/MMT 混合体系即EP/D400-T500-MMT 混合体系, 系统地研究了该体系与纯环氧树脂体系在130, 140, 150 及160 ℃等几个温度下的等温固化过程, 考察了等温固化时间对固化度和固化度变化速率的影响以及固化度与固化度变化速率之间的关系, 并利用Kamal 模型进行拟合计算了固化动力学参数. 研究结果表明, 与纯环氧树脂相比, 几种聚醚胺改性MMT 的固化放热峰均向高温迁移, 同时聚醚胺D400 协同插层MMT 降低了高分子量聚醚胺插层MMT 所导致的环氧树脂DSC 曲线的畸变情况; EP/D400-T500-MMT 混合体系和纯环氧体系的等温固化反应过程符合Kamal 模型;在相同的固化温度下, EP/D400-T5000-MMT 混合体系的反应速率常数k1k2 值以及反应级数m 均比纯EP 体系小, 而反应级数n 以及总反应级数m+n 值比纯EP 体系大, 表明两种聚醚胺协同插层的改性蒙脱土D400-T5000-MMT 的加入降低了环氧体系固化反应速率. 另外, EP/D400-T5000-MMT 混合体系的活化能Ea1Ea2 与纯EP 体系的相比也略有升高.  相似文献   

17.
The chemorheology and curing kinetics of a new high performance resin transfer molding benzoxazine resin was investigated. A chemorheological model based on a modified Arrhenius equation that describes the resin viscosity as a function of temperature and time was proposed. The model, which agreed well with the experimental data, can provide theoretical support for the mold-filling stage in the resin transfer molding process. The average activation energies of the polymerization reaction were obtained by means of gelation times at different temperatures based on the Arrhenius equation and from dynamic differential scanning calorimetry (DSC) results based on the Kissinger and Ozawa methods; the values were 96.0,84.0 and 87.8 KJ/mol, respectively. A plot of activation energy vs. conversion in the curing process was obtained using the Flynn-Wall-Ozawa model. The reaction orders were estimated from isothermal DSC based on a modified Kamal kinetics model which can describe both the autocatalytic and diffusion-controlled curing mechanism.  相似文献   

18.
ZnCl2/粘土-SA01催化合成二苯甲烷反应动力学研究   总被引:1,自引:0,他引:1  
在ZnCl2/粘土-SA01催化剂上合成了二苯甲烷,考察了负载量、苯/苄基氯摩尔比、催化剂用量、反应温度和时间对该反应的影响,研究了以ZnCl2/粘土-SA01为催化剂合成二苯甲烷的反应动力学,为探讨其反应机理和研究烷基化反应动力学提供了依据.结果表明,温度在303-318K时,本征动力学方程为r=k[ZnCl2/粘土-SA01]0.8[C6H6][C6H5CH2Cl],属二级反应,表观反应活化能为88.6kJ/mol;在328-353K时,其本征动力学方程为r=k[ZnCl2/粘土-SA01]0.1,反应属零级反应,表观活化能为52.8kJ/mol.  相似文献   

19.
三聚磷酸二氢铝吸附Cd~(2+)的动力学研究   总被引:1,自引:0,他引:1  
采用动态吸附法研究三聚磷酸二氢铝吸附镉离子的动力学行为并进行吸附活化状态热力学参数分析。结果表明,当三聚磷酸二氢铝粒径小于150μm、搅拌器转速大于200r/min、Cd2+的初始浓度为500mg/L时,三聚磷酸二氢铝对镉离子的化学吸附符合二级反应动力学方程,吸附速率常数k与温度T之间的关系符合Arrhenius方程式,吸附的活化能为Ea=27.93kJ/mol,吸附的频率因子A=65.33L/mg·min,ln(k/T)与1/T之间的关系符合Eyring公式,其活化焓ΔH=25.44kJ/mol,活化熵ΔS=-218.54J/mol·K。  相似文献   

20.
The effects of hyperbranched polyesters on the cure kinetics of diglycidyl ether of bisphenol A (DGEBA) in the presence of m‐phenylene diamine were investigated with nonisothermal differential scanning calorimetry. The results showed that the addition of hyperbranched polyesters enhanced the cure reaction of DGEBA with m‐phenylene diamine, and this resulted in a reduction of the peak temperature of the curing curve and the activation energy because of the low viscosity and large number of terminal hydroxyl groups. However, when linear poly(ethylene glycol) was added, the activation energy of the blends also slightly decreased, whereas the peak temperature of the curing curve increased. The curing kinetics of the blends were calculated by the isoconversional method of Málek. The two‐parameter autocatalytic model (i.e., the ?esták–Berggren equation) was found to be the most adequate for describing the cure kinetics of the studied systems. The obtained nonisothermal differential scanning calorimetry curves showed results in agreement with those theoretically calculated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2649–2656, 2004  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号