温度对LiCoO2中锂离子嵌脱过程的影响

摘要 运用EIS研究了LiCoO2正极在1M LiPF6-EC:DEC:DMC和1M LiPF6-PC:DMC+5%VC电解液中0~30℃范围内阻抗谱特征、SEI膜阻抗、电子电阻和电荷传递电阻等随温度的变化。结果表明,LiCoO2正极的EIS谱特征与温度有关,随温度的升高其低频区域在1M LiPF6-EC:DEC:DMC和1M LiPF6-PC:DMC+5%VC电解液中分别于10和20℃出现反映锂离子固态扩散的斜线。LiCoO2正极在 1M LiPF6-EC:DEC:DMC和1M LiPF6-PC:DMC+5%VC电解液中,锂离子迁移通过SEI膜的离子跳跃能垒平均值分别为37.74和26.55KJ/mol;电子电导率的热激活化能平均值分别为39.08和53.81KJ/mol;嵌入反应活化能平均值分别为68.97和73.73KJ/mol。     

温度对尖晶石LiMn2O4中锂离子嵌脱过程的影响

运用电化学阻抗谱研究了商品化尖晶石LiMn₂O₄电极在1 mol/L LiPF₆-EC(碳酸乙烯酯):DEC(碳酸二乙酯)电解液中―10～30 ℃范围内的阻抗谱特征、固体电解质相界面(SEI)膜阻抗、电子电阻和电荷传递电阻等随温度的变化. 研究结果表明, 尖晶石LiMn₂O₄电极的阻抗谱特征与温度有关, 随温度的升高, 与活性材料电子电导率相关的半圆和与SEI膜相关的半圆会发生重叠而成为一个半圆. 通过选取适当的等效电路拟合了实验所得的电化学阻抗谱数据, 测得尖晶石LiMn₂O₄电极在1 mol/L LiPF₆-EC:DEC 电解液中, 锂离子迁移通过SEI膜的离子跳跃能垒平均值为15.49 kJ/mol; 电子电导率的热激活化能平均值为24.21 kJ/mol; 嵌入反应活化能平均值为53.07 kJ/mol.     

温度对石墨电极性能的影响

运用电化学阻抗谱(EIS)并结合循环伏安法(CV)研究了石墨电极25和60 ℃时在1 mol·L-1 LiPF6-EC(碳酸乙烯酯):DEC(碳酸二乙酯):DMC(碳酸二甲酯)电解液中, 以及60 ℃时在1 mol·L-1 LiPF6-EC:DEC:DMC+5%VC(碳酸亚乙烯酯)电解液中的首次阴极极化过程. 发现高温下(60 ℃)石墨电极在1 mol·L-1 LiPF6-EC:DEC:DMC电解液中可逆循环容量衰减的主要原因在于其表面无法形成稳定的固体电解质相界面(SEI)膜. 实验结果显示, VC添加剂能够增进高温下石墨电极表面SEI膜的稳定性, 进而改进石墨电极的循环性能.     

Li_2CO_3添加剂对石墨电极性能的影响

运用电化学阻抗谱(EIS)和循环伏安法(CV)研究了在1mol/LLiPF6-EC(碳酸乙烯酯):DMC(碳酸二甲酯)电解液中添加Li2CO3对石墨电极性能的影响及机制.CV研究结果表明,在1mol/LLiPF6-EC:DMC电解液中添加Li2CO3能够有效抑制石墨电极首次充放电过程中碳酸乙烯酯(EC)的单电子还原过程,即还原分解产生乙烯和碳酸锂的过程,进而改善石墨电极的电化学循环性能.EIS研究结果表明,在添加Li2CO3的1mol/LLiPF6-EC:DMC电解液中,石墨电极表面的固体电解质相界面膜(SEI膜)具有较强的黏弹性,可以更好地适应锂离子嵌入过程中石墨颗粒体积的微小变化,从而使锂离子的嵌入过程更容易进行.     

石墨负极电化学扫描循环过程的EIS、Raman光谱和XRD研究

运用电化学阻抗谱(EIS)、Raman光谱和XRD研究了石墨负极在1 mol/L LiPF6-EC∶DEC∶DMC电解液中的电化学循环扫描过程. EIS研究结果表明, 在电化学循环扫描4~10周范围内, SEI膜(固体电解质相界面膜)电阻随循环扫描周数增加近似线性增长, 但石墨负极/电解液界面总阻抗由于电荷传递电阻的降低而减小. Raman光谱研究结果表明, 在经历电化学循环扫描后, 活性材料表层发生粉化和无定形化, 石墨化程度降低; 但XRD研究结果显示, 石墨材料的本体结构没有发生变化, 仍然保持着完整的石墨层状结构.     

白藜芦醇对长期贮存锂离子电池电解液性能的影响

锂离子电池电解液从制造完成到使用,一般都会经历灌装、运输和贮存的过程,了解长期贮存过程对锂离子电池电解液性能的影响,对锂离子电池的生产具有一定的理论指导意义.本文运用电化学阻抗谱(EIS)测试并结合循环伏安法(CV)测试、充放电测试、扫描电子显微镜(SEM)等研究了1 mol.L-1 LiPF6-EC:EMC 基础电解...     

V_2O_5/C电化学电容器有机电解液的性能研究

以偏钒酸铵为反应原料,采用液相沉淀法制备出不定型V2O5电极材料.以V2O5为正极,石墨为负极,分别选用1.0 mol/L LiClO4/EC+DMC、1.0 mol/L LiPF6/EC+DEC+DMC、1.6 mol/L Et4NBF4/AN 3种有机电解液组成不对称电化学电容器,恒流充放电、循环伏安和交流阻抗等测试该模拟电容器,如以1.0 mol/LLiClO4/EC+DMC作电解液则具有良好的循环性能和较小的阻抗,且在500 mA/g电流密度下比能量达到8.4Wh/kg,充放电效率达98%.     

锂离子电池LiMn2O4正极材料的高温改性

锂离子电池LiMn2O4正极材料的高温改性;锂离子电池;正极材料;尖晶石;LiMn2O4;包覆     

尖晶石LiMn2O4中锂离子嵌入脱出过程的电化学阻抗谱研究

运用电化学阻抗谱(EIS)研究了尖晶石LiMn2O4电极的首次充放电过程. 发现EIS谱高频区域拉长压扁的半圆是由两个半圆相互重叠而成的, 分别归属于与锂离子通过固体电解质相界面膜(SEI膜)的迁移和与尖晶石LiMn2O4材料的电子电导率相关的特征. 通过选取适当的等效电路, 对实验所得的电化学阻抗谱数据进行拟合, 获得尖晶石LiMn2O4电极首次充放电过程中SEI膜电阻、电子电阻和电荷传递电阻等随电极极化电位变化的规律. 根据研究结果提出了嵌锂物理机制模型.     

Impedance Studies of Spinel LiMn2O4 Electrode/electrolyte Interfaces

The formation process of solid electrolyte interphase（SEI） film on spinel LiMn2O4 electrode surface was studied by electrochemical impedance spectroscopy（EIS） during the initial storage in 1 mol/L LiPF6-EC：DMC：DEC electrolyte and in the subsequent first charge-discharge cycle. It has been demonstrated that the SEI film thickness increased with the increase of storage time and spontaneous reactions occurring between spinel LiMn2O4 electrode and electrolyte can be prevented by the SEI film. In the first charge-discharge cycle succeeding the storage, the electrolyte oxidation coupled with Li-ion insertion is evidenced as the main origin to increase the resistance of SEI film. The results also confirm that the variations of the charge transfer resistance（Rot） with the electrode potential（E） can be well described using a classical equation.     

锂离子电池电解液中甲醇杂质对石墨电极性能影响机制的电化学阻抗谱研究

运用电化学阻抗谱和循环伏安法研究了在1mol/LLiPF6-EC/DEC/DMC电解液中,不同甲醇杂质含量对石墨电极性能的影响及其机制.结果表明,甲醇对石墨电极性能的影响与电解液中甲醇的含量有关;其对石墨电极性能的影响机制为甲醇在2.0V左右还原生成的甲氧基锂沉积在石墨电极表面上,形成一层初始SEI膜,影响了EC的还原分解成膜过程.     

添加剂氟代碳酸乙烯酯对锂离子电池性能的影响

在1 mol·L-1 LiPF6/碳酸乙烯酯(EC)+碳酸二甲酯(DMC)+碳酸甲乙酯(EMC)(EC、DMC、EMC体积比为1:1:1)电解液中加入体积比为2%的添加剂氟代碳酸乙烯酯(FEC), 用循环伏安法(CV)、扫描电镜(SEM)、能量散射光谱(EDS)、电化学阻抗谱(EIS)等方法, 研究了FEC 对锂离子电池性能及石墨化中间相碳微球(MCMB)电极/电解液界面性质的影响. 结果表明, 体积比2%FEC的添加可以抑制部分电解液溶剂的分解, 在MCMB电极表面形成一层性能优良的固体电解液相界面(SEI)膜, 降低了电池的阻抗, 明显提高了电池的比容量和循环稳定性.     

LiCoO_2 electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO2 electrode in 1 mol/L LiPF6-EC:DMC:DEC elec- trolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO2 electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO2 electrode in Li/LiCoO2 cells is attributed to the formation of a Li1-xCoO2/LiCoO2 concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO2 hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5.     

尖晶石锂锰氧化物电极首次脱锂过程的EIS研究

研究了尖晶石锂锰氧化物电极首次脱锂过程中的电化学阻抗特征. 通过选取适当的等效电路拟合实验所得的电化学阻抗谱数据, 获得了首次脱锂过程中固体电解质相界面膜(SEI膜)的电阻、电容以及电荷传递电阻、双电层电容等随电极极化电位的变化规律.     

LiCoO<Subscript>2</Subscript> electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO₂ electrode in 1 mol/L LiPF₆-EC:DMC:DEC electrolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO₂ electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO₂ electrode in Li/LiCoO₂ cells is attributed to the formation of a Li_1−x CoO₂/LiCoO₂ concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO₂ hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5. Supported by the Special Funds for Major State Basic Research Project of China (Grant No. 2002CB211804)     

新型锂盐LiBC2O4F2在EC+DMC溶剂中的电化学行为

采用差热-热重(TG-DTA)、恒电流充放电和交流阻抗(EIS)分析了二氟草酸硼酸锂(LiODFB)的热稳定性, 研究了LiODFB/碳酸乙烯酯(EC)+碳酸二甲酯(DMC)电解液的电化学性能及界面特征. 实验结果表明, LiODFB不仅具有更高的热稳定性, 而且在EC+DMC溶剂中具有较好的电化学性能. 与使用LiPF6/EC+DMC的电解液相比, 锂离子电池应用LiODFB基电解液在55 ℃的高温具有更好的容量保持能力; 以0.5C、1C(1C=250 mA·g-1)倍率循环放电, 两种电池间的倍率性能差别较小; LiODFB能够在1.5 V(vs Li/Li+)左右在石墨电极表面还原形成一个优异稳定的保护性固体电解质相界面膜(SEI膜); 交流阻抗表明, 使用LiODFB基电解液的锂离子电池仅具有稍微增加的界面阻抗. 因此LiODFB是一种非常有希望替代LiPF6用作锂离子电池的新盐.