含氨基聚芳醚酮/磺化聚芳醚酮砜中高温质子交换复合膜的制备与性能研究

以自制的高磺化度磺化聚芳醚酮砜(SPAEKS)和含有氨基的聚芳醚酮(Am-PAEK)为原料,通过共溶剂涂膜法制备了不同重量比例的Am-PAEK/SPAEKS复合膜.通过高温(160℃)处理使氨基和磺酸基团在复合膜内形成交联,制得交联型复合膜.复合膜的热性能、尺寸稳定性、阻醇性能有所提高,而且交联型复合膜中的Am-PAEK/SPAEKS-C-3质子传导率在120℃时达到了0.0892 S/cm,高于在相同测试条件下SPAEKS膜的0.0654 S/cm和Nafion膜的0.062 S/cm,而其甲醇渗透系数在25℃时达到0.14×10-6cm2/s,低于SPAEKS膜的0.85×10-6cm2/s和Nafion膜的2×10-6cm2/s.实验结果表明,Am-PAEK/SPAEKS交联型复合膜有望在中高温质子交换膜燃料电池中得到应用.     

A new macrocyclic polystyrene-based sensor for chromium (III) ions

A new tetradentate dihydrogen perchlorate macrocyclic ligand (2,4,9,11-tetraphenyl-1,5,8,12-tetraazacyclotetradeca-1,4,8,11-tetraene dihydrogen perchlorate) was prepared and characterised. The macrocycle behaves as a selective chelating ion-exchanger for some metal ions. The polystyrene-based membrane electrode is found to exhibit quite promising selectivity for Cr3+ ions. It can be used to estimate chromium concentrations in the range 3.16x 10(-6)-1.00x10(-1) M with a near-Nernstian slope of 17.5 mV per decade of concentration between pH 3.0 to 6.5. The electrode is found to possess a fast response time of 15 s and was used over a period of three months with good reproducibility (s = +/- 0.3 mV). The selectivity coefficient values for mono-, di- and trivalent cations indicate excellent selectivity for Cr3+ ions over a large number of other cations. Anions such as Cl- and SO4(2-) do not interfere and the electrode also works satisfactorily in a mixed organic-water solution. The sensor has been used as an indicator electrode for the potentiometric titration of Cr3+ with EDTA. The practical utility of the membrane sensor has also been demonstrated in solutions contaminated with detergents (CTAB and SDS). Above all, the membrane sensor has been very successfully used to determine Cr3+ in some foods.     

Diffusion Kinetics Study of Lithium Ion in the Graphdiyne Based Electrode

Herein,we report a comparative investigation of the electrochemical lithium diffusion within graphidyne(GDY)based electrodes.The transfer kinetic behaviors of lithium ions during the insertion/extraction process are analyzed through different methods including the galvanostatic intermittent titration technique(GITT)and the electrochemical impedance spectroscopy(EIS).GDY with the morphology of nanosheets(GDY NS)shows lithium diffusion coefficients in the orders range of 10-12-10-13 cm2/s through the GITT method.Meanwhile,EIS indicates quite a lower value of lithium diffusion coefficients between 10-13 and 10-15 cm2/s,which indicates that the analysis technique has an influence on the evaluation of GDY-based electrodes.In addition,under the same measurement condition of GITT,GDY nanoparticles(GDY NP)exhibit a lower value of Li+diffusion coefficient(10-14-10-16 cm2/s)during the charge-discharge process compared to those of GDY NS,which can be ascribed to the wide distributing range of particle size in GDY NP based electrodes.The analysis results in this work reveal that the aggregating forms of GDY electrode material have an important effect on the diffusion process of lithium ions,which provides a pathway to optimize the performance of GDY-based energy storage devices.     

Immobilizing single lipid and channel molecules in artificial lipid bilayers with annexin A5

The effects of annexin A5 on the lateral diffusion of single-molecule lipids and single-molecule proteins were studied in an artificial lipid bilayer membrane. Annexin A5 is a member of the annexin superfamily, which binds preferentially to anionic phospholipids in a Ca2+-dependent manner. In this report, we were able to directly monitor single BODIPY 1,2-dihexadecanoyl-sn-glycero-3-phosphoethanolamine (DHPE) and ryanodine receptor type 2 (RyR2) labeled with Cy5 molecules in lipid bilayers containing phosphatidylserine (PS) by using fluorescence microscopy. The diffusion coefficients were calculated at various annexin A5 concentrations. The diffusion coefficients of BODIPY-DHPE and Cy5-RyR2 in the absence of annexin A5 were 4.81 x 10(-8) cm(2)/s and 2.13 x 10(-8) cm(2)/s, respectively. In the presence of 1 microM annexin A5, the diffusion coefficients of BODIPY-DHPE and Cy5-RyR2 were 2.2 x 10(-10) cm(2)/s and 9.5 x 10(-11) cm(2)/s, respectively. Overall, 1 microM of annexin A5 was sufficient to induce a 200-fold decrease in the lateral diffusion coefficient. Additionally, we performed electrophysiological examinations and determined that annexin A5 has little effect on the function of RyR2. This means that annexin A5 can be used to immobilize RyR2 in a lipid bilayer when imaging and analyzing RyR2.     

Rhodamine B diffusion in hair as a probe for structural integrity

The aim of this work was to investigate the diffusion of Rhodamine B into bleached, photo bleached and abraded hair, treated or not with an emulsion of ceramide using two different techniques: spectrophotometry and fluorescence optical microscopy with image analysis. This comparison, combined with the Einstein-Smoluchowski equation, allowed validating a methodology that uses the apparent diffusion coefficient of a dye as an index for hair damage. Distinct behaviors of the dye were observed in the cuticle and in the cortex. For a bleached hair sample the apparent diffusion coefficient in the cuticle ranges from 8.2 x 10(-11) cm2 s(-1) to 10 x 10(-11)cm2 s(-1), while for the cortex this value drops to 4.0 x 10(-11) cm2 s(-1) to 4.2 x 10(-11) cm2 s(-1). The diffusion is always faster in the cuticle than in the cortex and the apparent diffusion coefficient shows up to a seven-fold decrease when the dye penetrates the cortex. The chemical, photochemical and physical treatments applied to hair significantly change the values of the apparent diffusion coefficients in the cuticle. The data also proved that the penetration of Rhodamine B into hair occurs via an intercellular path.     

NMR diffusion spectroscopy as a measure of host-guest complex association constants and as a probe of complex size

The complexes of cyclohexylacetic acid and cholic acid with beta-cyclodextrin were studied by NMR diffusion coefficient measurements. The diffusion coefficient of the 1:1 cyclohexylacetic acid/beta-cyclodextrin complex, K(a) = 1800 +/- 100 M(-1), is slightly slower (3.23 +/- 0.07 x 10(-6) cm(2) s(-1)) than that of beta-cyclodextrin (3.29 +/- 0.07 x 10(-6) cm(2) s(-1)). The diffusion coefficient of the 1:1 cholic acid/beta-cyclodextrin complex, K(a) = 5900 +/- 800 M(-1), is significantly slower (2.93 +/- 0.07 x 10(-6) cm(2) s(-1)) than that of beta-cyclodextrin. The results indicate that caution should be exercised when studying host-guest complexation by the so-called 'single point' technique. A novel data treatment is introduced which takes into account the diffusion behavior of all of the species when determining K(a). Experimentally determined diffusion coefficients of complexes are also a useful probe of the size of host-guest complexes.     

Size-selective voltammetry: modification of the interface between two immiscible electrolyte solutions by zeolite Y

Size- and charge-selective ion transfer across the zeolite-Y-modified interface between two immiscible electrolyte solutions (ZM-ITIES) is described. The zeolite-Y membrane is prepared from pressed disks by healing with tetraethyl orthosilicate (TEOS). Size- and charge-selective transfer of the tetraethylammonium cation, size-selective exclusion of tetrabutylammonium cation, and charge-selective exclusion of the tetrafluoroborate and perchlorate anions are demonstrated at the ZM-ITIES. The exclusion studies suggest that the membrane is coherent and contains a low density of pinholes, after healing with TEOS. Various factors affecting the ion transfer such as analyte concentration, supporting electrolyte concentration, and scan rate are investigated. The diffusion coefficient of tetraethylammonium ions within the zeolite-Y pores is found to be on the order of 10(-8) cm2 s(-1).     

Ion-exchange voltammetry of dopamine at Nafion-coated glassy carbon electrodes: quantitative features of ion-exchange partition and reassessment on the oxidation mechanism of dopamine in the presence of excess ascorbic acid

The incorporation/exclusion features of dopamine (DA), ascorbic acid (AA) and uric acid (UA) are evaluated for Nafion (NA)-coated glassy carbon electrodes (GCE) of different thicknesses. The ion-exchange partition of DA(+) between the NA film and the sodium phosphate electrolyte is evaluated by determining the partition coefficient (k(D)) and the apparent diffusion coefficient (D(app)) in thick NA films which were 401 and 1.5 x 10(-9) cm(2) s(-1), respectively. The solution diffusion coefficient was found to be 6.0 x 10(-6) cm(2) s(-1). Also, the effect of NA loading and of the voltammetric timescale on DA voltammetry in the presence of excess AA is assessed, at physiologic like conditions. It is demonstrated that, although AA is excluded at the NA coating, a catalytic regeneration of DA, induced by AA, occurs at the interface NA film/electrolyte resulting from the diffusion of the o-quinone product of DA oxidation from the electrode surface to that interface. The interference of AA in the voltammetric signal of DA is eliminated using 18 microg mm(-2) NA films and v> or =0.5 V s(-1). Therefore, fast, selective and sensitive voltammetric analysis of DA at concentrations<100 microM in the presence of excess AA, e.g., 1 mM is achieved.     

Ion diffusion and electrochemical capacitance in aligned and packed single-walled carbon nanotubes

Direct measurement of ion diffusion in aligned, densified single-walled carbon nanotube electrodes showed that the diffusion coefficient for transport of ions (KSCN in acetonitrile) parallel to the alignment direction of the nanotubes was close to the theoretical limit of perfectly straight pores, achieving a value 20 times larger than that of activated carbon electrodes (1 × 10(-5) vs 5 × 10(-7) cm(2)/s). In contrast, the diffusion coefficient for ion transport perpendicular to the alignment direction was an order of magnitude smaller (8 × 10(-7) cm(2)/s). As an example of the ramifications of this anisotropic diffusion phenomenon, the difference in performance of the aligned carbon nanotubes as electrochemical-capacitor electrodes was evaluated. At low discharge rates, the performances of the two orientations were identical, but as the discharge rate was increased, a more rapid decline in capacitance was observed for the perpendicular orientation (66 vs 14% decline in capacitance when the discharge current was increased from 0.01 to 1 A/g). Furthermore, the maximum power rating of the perpendicular electrode was lower than that of the parallel electrode (1.85 vs 3 kW/kg during operation at 1 V).     

Radiotracer studies on calcium ion-selective electrode membranes based on poly(vinyl chloride) matrices

Radiotracer studies with ⁴⁵Ca and ³⁶Cl demonstrate that PVC matrix membranes containing Orion 92-20-02 liquid calcium ion-exchanger are permselective to counter-cations. Diffusion coefficients are quoted for the migration of ⁴⁵Ca between pairs of calcium solutions and are discussed in terms of solution concentration, membrane thickness and concentration level of sensor in the membrane. Migration of calcium ions from calcium chloride solution to a Group (II) metal chloride solution through a PVC membrane containing calcium liquid ion-exchanger is discussed in terms of solvent extraction and electrode selectivity coefficient parameters. Thus, magnesium, strontium and barium ions appear to inhibit migration through the membrane by their low affinity for the membrane liquid ion-exchanger sites, while the inhibition by beryllium ions is attributed to site blockage by the strong affinity of dialkylphosphate sites for beryllium.     

Film-Pore Diffusion Control for the Batch Sorption of Cadmium Ions from Effluent onto Bone Char

The sorption equilibrium and kinetics of cadmium ions from aqueous solution onto bone char have been studied. Equilibrium isotherms for the sorption system were correlated by Langmuir and bi-Langmuir equations. The application of the bi-Langmuir equation was developed because the mechanistic analysis in this research indicated that cadmium removal occurs ion exchange and physical adsorption onto different surface sites. The bi-Langmuir equation provides a better fit to the experimental data. In addition, the removal rates of cadmium ions based on the Langmuir models have been investigated. The effective diffusivity was calculated using the effects of initial metal ion concentration and bone char mass. Two mass-transport models based on film-pore diffusion control have been applied to analyze the concentration decay curves. The film and pore diffusion coefficients using an analytical equation are equal to 1.26x10(-3) cm/s and 5.06x10(-7) cm(2)/s, respectively. The pore diffusion coefficient obtained from the numerical method is 4.89x10(-7) cm(2)/s. A sensitivity analysis showed that the film-pore diffusion model and constant effective diffusivity could be used to describe the mass-transport mechanism of the sorption system with a high degree of correlation. Copyright 2001 Academic Press.     

A chlorate ion-selective electrode based on a poly(vinyl chloride)-matrix membrane

An electrode has been prepared, consisting of a PVC membrane containing Corning 477316 nitrate liquid ion-exchanger in the chlorate form, which responds to chlorate ions. It has a faster response (1-2 sec) and lower limit of detection (3 x 10(-5)M) than the nitrate electrode for chlorate determination. Selectivity coefficients for the electrode towards several other ions have been measured.     

Self-assembly of solid-supported membranes using a triggered fusion of phospholipid-enriched proteoliposomes prepared from the inner mitochondrial membrane

A general procedure for the formation ofsolid-supported artificial membranes containing transmembrane proteins is reported. The main objective was to directly use the pool of proteins of the native biomembrane (here the inner membrane from mitochondria of human carcinogenic hepatic cells) and to avoid purification steps with detergent. Proteoliposomes of phospholipid-enriched inner membranes from mitochondria were tethered and fused onto a tailored surface via a streptavidin link. The failure of some preliminary experiments on membrane formation was attributed to strong nonspecific interactions between the solid surface and the protuberant hydrophilic parts of the transmembrane complexes. The correct loading of uniform membranes was performed after optimization of a tailored surface, covered with a grafted short-chain poly(ethylene glycol), so that nonspecific interactions are reduced. Step-by-step assembly of the structure and triggered fusion of the immobilized proteoliposomes were monitored by surface plasmon resonance and fluorescence photobleaching recovery, respectively. The long-range lateral diffusion coefficient (at 22 degrees C) for a fluorescent lipid varies from 2.5 x 10(-8) cm2 s(-1) for a tethered lipid bilayer without protein to 10(-9) cm2 s(-1) for a tethered membrane containing the transmembrane proteins of the respiratory chain at a protein area fraction of about 15%. The decrease in the diffusion coefficient in the tethered membrane with increase in protein area fraction was too pronounced to be fully explained by the theoretical models of obstructed lateral diffusion. Covalent tethering links with the solid are certainly involved in the decrease of the overall lateral mobility of the components in the supported membrane at the highest protein-to-lipid ratios.     

Proton diffusion across membranes of vesicles of poly(styrene-b-acrylic acid) diblock copolymers

A study of proton diffusion across membranes of block copolymer vesicles in dilute solution is described. The vesicles were formed by the self-assembly of a diblock copolymer of poly(styrene-b-acrylic acid) (PS(310)-b-PAA(36), where the numbers represent the degree of polymerization for individual blocks). A pH gradient was created across the vesicle membrane with the interior pH (pH(in)) of ca. 2.9 and the exterior pH (pH(out)) of ca. 8.5. The permeability of the polystyrene (PS) membrane was tuned by the addition of different amounts of dioxane (0-40 wt %) to the external aqueous solution. Proton concentrations in the solution outside of the vesicles were followed by monitoring the spectrum of a pH-sensitive fluorescent dye, namely 8-hydroxypyrene-1,3,6-trisulfonate. After the start of the experiment, the proton concentrations increase linearly with the square root of time, while the slopes of the lines increase with dioxane content. To calculate the diffusion coefficients of the protons across the vesicular membrane, the concentration data were fitted using a model, which describes the diffusion of species across the membrane of a reservoir. The apparent diffusion coefficient (D*, which equals the true diffusion coefficient multiplied by the partition coefficient of protons between PS and water) increases from 1.1 x 10(-18) cm(2)/s at 7 wt % dioxane in the external solution to 1.2 x 10(-14) cm(2)/s at 40 wt %. The increase of D* with dioxane content is related to its plasticization of the PS membrane, which can be used as a gating mechanism.     

Impact of membrane immobilization on particle formation and trichloroethylene dechlorination for bimetallic Fe/Ni nanoparticles in cellulose acetate membranes

The use of membrane immobilization to carry out the batch dechlorination of trichloroethylene (TCE) using bimetallic Fe/Ni (4:1, Fe to Ni) nanoparticles in cellulose acetate membranes is examined using modeling of transport phenomenon based on experimental results. Membranes are synthesized using both gelation and solvent evaporation techniques for phase inversion. The reduction of metal ions within cellulose acetate phase-inversion membranes was accomplished using sodium borohydride reduction to obtain up to 2 wt % total metals. Characterization of the mixed-matrix structure reveals a bimodal particle distribution ranging between 18 and 80 nm within the membrane cross section. The distribution is the result of changes in the morphology of the cellulose acetate support. The diffusivity and linear partitioning coefficient for the chlorinated organic were measured and are 2.0 x 10(-8) cm2.s-1 and 3.5 x 10(-2) L.g-1, respectively. An unsteady-state model for diffusion through a membrane with reaction was developed to predict experimental results with an error of only 7.2%. The error can be attributed to the lack of the model to account for loss of reactivity through pH effects, alloy effects (bimetallic ratio), and oxidation of nanoparticles. Simulations were run to vary the major transport variables, partitioning and diffusivity, and determine their impact on reaction kinetics. Of the two, diffusivity was less significant because it really only influences the time required for maximum TCE partitioning to the membrane to be achieved and has no effect on the limiting capacity of the membrane for TCE. Therefore, selection of an appropriate support material is crucial for development of highly reactive mixed-matrix membrane systems.     

Use of ethylene-vinyl-acetate as a new membrane matrix for calcium ion-selective electrode preparation

A new polymer matrix based membrane electrode with an ion-exchanger responding to calcium was constructed by dissolving the copolymer ethylene-vinyl-acetate together with the ion-exchanger in chloroform in the presence of a mixture of dioctylphthalate-nitrobenzene as plasticizer. The ion-exchanger used as the electroactive component was calcium didecyl phosphate in di-(n-octylphenyl) phosphonate (Orion). This electrode exhibited near-Nernstian response over the concentration range 10(-1)-4 x 10(-6)M calcium. The pH did not affect the electrode performance within the range 8-11. Response time varied from 15 to 120 sec and the lifetime exceeded six months. The membrane is subject to static charge buildup, but this is avoided by controlling the level of dryness of the membrane. Selectivity coefficients determined for both monovalent and divalent cations showed negligible interference by most of these ions. The electrode was applied successfully to the determination of calcium in commercial mineral waters.     

EuCl_3在氯化1-丁基-3-甲基咪唑中的电化学性质

应用循环伏安法研究了Eu3+在亲水性离子液体—氯化1-丁基-3-甲基咪唑([BMIM]Cl)中的电极过程.实验表明,工作电极为玻碳电极时,[BMIM]Cl的电化学窗口为-1.7～0.80V(vs.Ag/AgCl).Eu3+在[BMIM]Cl中被还原为Eu2+,此电极反应受电荷迁移和物质扩散共同控制.当体系温度从55℃升高到75℃时,Eu3+在[BMIM]Cl中的扩散系数D从3.75×10-9cm2/s变化到1.32×10-8cm2/s,该反应活化能Ea为62.6kJ/mol.     

氧在甲基丙烯酸辛酯-乙烯基咪唑共聚物/钴卟啉复合膜中的溶解和扩散过程

讨论了氧在甲基丙烯酸辛酯 乙烯基咪唑共聚物 钴卟啉复合膜中的溶解和扩散过程,用二元输送模型分析了间α,α,α,α-四(邻三甲基乙酰胺苯基)钴卟啉(CoP)作为氧载体的复合膜氧输送性能.研究发现,固定在聚合物中的CoP与氧可逆地络合和解络合,其络合平衡常数K为14mol- 1 L ,根据吸附实验结果计算出氧在基体聚合物中的物理溶解度系数kD 为4 4×10 - 5cm3(STP)cm- 3Pa- 1 .聚合物 载体复合膜除了物理渗透外,氧还可通过与载体的络合和解络合而扩散,从而促进氧的输送.氧通过载体的扩散系数(DC)和通过基体聚合物的物理扩散系数(DD)的比值为0 0 8.     

Molecular basis of carbon dioxide transport in polycarbonate membranes

Gas transport of carbon dioxide in poly[bisphenol A carbonate-co-4,4'-(3,3,5-trimethylcyclohexylidene)diphenol carbonate] films over a wide range of pressure is described. The interpretation of the experimental results in terms of the dual mode model allowed the evaluation of the parameters of the model that govern the gas permeation process. The value of the diffusion coefficient obtained for carbon dioxide at zero concentration was 2.4 x 10(-8) cm(2) s(-1), at 303 K. This parameter was also measured by using pulsed field gradient NMR finding that its value reaches a nearly constant value of (2.7 +/- 0.9) x 10(-8) cm(2) s(-1), at 298 K, for diffusion times greater than 20 ms. Both the diffusion and solubility coefficients were also computed by using simulation methods based on the transition states theory and the Widom method, respectively. The value obtained for the diffusion coefficient was 1.8 x 10(-8) cm(2) s(-1), at 303 K, which compares very favorably with the experimental measurements. The drop of the simulated solubility coefficient with increasing pressure is sharper than that of the experimental one, at low pressures, and similar, at high pressures.     

Dynamic behavior of water within a polymer electrolyte fuel cell membrane at low hydration levels

Protonic conduction across the membrane of a polymer electrolyte fuel cell is intimately related to the dynamic behavior of water present within the membrane. To further the understanding of water dynamics in these materials, quasielastic neutron scattering (QENS) has been used to investigate the picosecond dynamic behavior of water within a perfluorosulfonated ionomer (PFSI) membrane under increasing hydration levels from dry to saturation. Evaluation of the elastic incoherent structure factor (EISF) reveals an increase in the characteristic length-scale of confinement as the number of water molecules in the membrane increases, tending to an asymptotic value at saturation. The fraction of elastic incoherent scattering observed at high Q over all hydration levels is well fit by a simple model that assumes a single, nondiffusing hydronium ion per membrane sulfonic acid site. The quasielastic component of the fitted data indicates confined dynamic behavior for scattering vectors less than 0.7 A(-1). As such, the dynamic behavior was interpreted using continuous diffusion confined within a sphere at Q < 0.7 A(-1) and random unconstrained jump diffusion at Q > 0.7 A(-1). As the number of water molecules in the membrane increases, the characteristic residence times obtained from both models is reduced. The increased dynamical frequency is further reflected in the diffusion coefficients predicted by both models. Between low hydration (2 H2O/SO3H) and saturation (16 H2O/SO3H), the continuous spherical diffusion coefficient changes from 0.46 +/- 0.12 to 1.04 +/- 0.12 (10(-5) cm2/s) and jump diffusion indicates an increase from 1.21 +/- 0.03 to 2.14 +/- 0.08 (10(-5) cm2/s). Overall, the dynamic behavior of water has been quantified over different length scale regimes, the results of which may be rationalized on the basis of the formation of water clusters in the hydrophilic domain that expand toward an asymptotic upper limit with increased hydration.