Charakterisierung anodischer Deckschichten an Platin-Elektroden mittels R?ntgen-Photoelektronenspektroskopie

Zusammenfassung Eine Platinelektrode wurde bei 3 V vs. SHE in 0,5 M H₂SO₄ und bei 3 V vs. Ag/AgCl-Bezugselektrode in 1 M NaOH anodisch polarisiert und die entstandenen oxidischen Deckschichten spektroskopisch analysiert. Mittels Röntgen-Photoelektronen- und Elektronenenergieverlust-Spektroskopie konnten die Passivschichten nach Transfer der Elektrode aus der elektrochemischen Zelle in ein Ultrahochvakuumsystem als Pt(OH)₄ (saurer Elektrolyt) und PtO(OH)₂ (alkalischer Elektrolyt) charakterisiert werden. Auch bei niedrigeren Potentialen scheint in H₂SO₄ Hydroxid als Oberflächenspezies vorzuliegen. Diese Untersuchungen stehen in Einklang mit voltammetrischen In-situ-Messungen.

---

Characterization of anodic coatings on platinum electrodes by X-ray photoelectron spectroscopy

Summary A platinum electrode was anodically polarized at 3 V vs. SHE in 0.5 M H₂SO₄ and in 1 M NaOH at 3 V vs. Ag/AgCl reference electrode and the oxidic coatings formed were spectroscopically analyzed. The passive layers could be characterized by X-ray photoelectron and electron energy loss spectroscopy after transferring the electrode from the electrochemical cell into a UHV system. The coatings were found to consist of Pt(OH)₄ (acid electrolyte) and PtO(OH)₂ (alkaline electrolyte). Hydroxide seems also to be the predominant surface species at lower potentials in H₂SO₄. These investigations are in agreement with voltammetric in situ measurements.

     

Comparison of electrocatalytic characterization of Ti/Sb-SnO<Subscript>2</Subscript> and Ti/F-PbO<Subscript>2</Subscript> electrodes

Electrocatalytic oxidation is a promising process for degrading toxic and biorefractory organic pollutants in wastewater treatment. Selection of electrode materials is crucial for electrochemical oxidation process. In this study, Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes were chosen to compare their electrocatalytic characterization, which were prepared by electrodeposition and thermal decomposition method, respectively. The surface morphology and crystal structure of two electrodes were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The linear polarization curves show that Ti/Sb-SnO₂ electrodes possess higher oxygen evolution overpotential than Ti/F-PbO₂ electrodes. But the stability and corrosion resistance ability of Ti/F-PbO₂ electrode was higher than that of Ti/Sb-SnO₂ electrode. The electrocatalytic activity of Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes was examined for the electrochemical oxidation of malachite green (MG). The bulk electrolysis shows that the Ti/Sb-SnO₂ electrodes exhibit the higher electrocatalytic activity for the degradation of MG than Ti/F-PbO₂ electrodes, and the degradation process is good fitting for the pseudo-first order reaction. The higher electrocatalytic activity of Ti/Sb-SnO₂ electrodes can be attributed to the higher oxygen evolution overpotential.     

Synthesis of Poly(<Emphasis Type="Italic">o</Emphasis>-anisidine)/H<Subscript>2</Subscript>SO<Subscript>4</Subscript> Film for the Development of Glucose Biosensor

The poly(o-anisidine)–sulfuric acid–glucose oxidase (POA–H₂SO₄–GOx) electrode has been investigated in the present work. Platinum electrode was used for the synthesis of poly (o-anisidine)–sulfuric acid (POA–H₂SO₄) film using galvanostatic method with 0.2 M o-anisidine, 1.0 M H₂SO₄ solution, 1.0 pH and 2 mA/cm² applied current density. The synthesized film was characterized using electrochemical technique, conductivity measurement, UV–visible spectroscopy, Fourier transform infrared spectroscopy, and scanning electron microscopy. GO_X was immobilized on synthesized POA–H₂SO₄ film by cross-linking via glutaraldehyde in phosphate and acetate buffer. The Michaelis–Menten constant ( K_\textm￠K_{\text{m}}^\prime ) was determined for the immobilized enzyme. The glucose oxidase electrode shows the maximum current response at pH 5.5 and potential 0.6 V. The sensitivity of POA–H₂SO₄–GO_X electrode in phosphate and acetate buffer has been recorded. The results of this study reveal that the phosphate buffer gives fast response as compared to acetate buffer in amperometric measurements.     

TiO<Subscript>2</Subscript> nanotube arrays based DSA electrode and application in treating dye wastewater

Dimensionally stable anode (DSA) of antimony-doped tin dioxide electrode based on TiO₂-nanotube arrays (NTs) has been successfully fabricated through thermal decomposition. The surface morphology and composition of the electrodes were characterized by using scanning electron microscopy and X-ray diffraction. Methyl orange (MO) was used as a model pollutant to investigate the electrochemical properties of these two electrodes. The optimized anodic oxidation voltage and time for TiO₂-nanotubes array based DSA electrode is 60 V and 10 min, respectively. The results show that Ti/TiO₂–NTs/Sb–SnO2 electrode has an increase of 100 mV in oxygen evolution overpotential and the service life is 56% longer than that of the traditional DSA electrode. Under the optimum conditions, MO solution decolorization rate and TOC removal rate reached approximately 100 and 80%, respectively. Study suggested that the as-prepared Ti/TiO₂–NTs/Sb–SnO2 DSA electrode exhibits high activity for degradation of organic pollutant with high concentration.     

High-performance supercapacitor electrode based on a nanocomposite of polyaniline and chemically exfoliated MoS<Subscript>2</Subscript> nanosheets

In this study, MoS₂ nanosheets were first prepared by exfoliating its bulk material in HCl/LiNO₃ solution with a yield of 45%, and then a facile strategy was developed to synthesize polyaniline/MoS₂ (PANI/MoS₂) nanocomposite via in situ polymerization. Structural and morphological characterizations of MoS₂ nanosheets and the nanocomposite were investigated by scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray powder diffraction. The results of SEM illustrated that orderly sawtooth polyaniline (PANI) nanoarrays were formed on the surface of MoS₂ nanosheets. The nanocomposite displayed good electrochemical performance as a supercapacitor electrode material. The specific capacitance reached 560 F/g at a current density of 1.0 A g^?1 in 1.0 M H₂SO₄ solution. Such good performance is because that the MoS₂ nanosheets provided a highly electrolytic accessible surface area for redox-active PANI and a direct path for electrons.     

Effect of H<Subscript>2</Subscript>SeO<Subscript>3</Subscript> on the early stages of nucleation and growth during Cu electrocrystallization in acidic medium on glassy carbon electrode

The early stages of Cu electrodeposition onto a GC electrode were investigated in 0.5 M H₂SO₄ + 0.01 M CuSO₄ solution without or with H₂SeO₃ when a molar concentration ratio [Cu(II)]/[Se(IV)] was 1.10⁴ to 2.10². The H₂SeO₃ solution in 0.5 M H₂SO₄ was also used. The electrochemical techniques such as cyclic voltammetry and chronoamperometry and structural investigation using ex situ AFM were applied to study the nucleation and growth of Cu onto a GC electrode. Chronoamperometric results were shown to follow an instantaneous 3D nucleation and diffusion-controlled growth model by Scharifker and Hills. The values of number of Cu nuclei N and average nuclei radius r _av were calculated. It was shown that, in the presence of H₂SeO₃ in amounts of 0.001 to 0.005 mM, N increases and r _av decreases. At higher concentrations of the additive, the changes of these parameters with the deposition potential E _dep were shown to be somewhat more complex. The dependences of N and r _av on the concentration of H₂SeO₃ in different regions of Cu overpotentials were also revealed.     

EQCM Study of Ru and RuO2 Surface Electrochemistry

The present study represents comparative analysis of voltammetric and microgravimetric behavior of active ruthenium (Ru), electrochemically passivated ruthenium (Ru/RuO₂) and thermally formed RuO₂ electrodes in the solutions of 0.5 M H₂SO₄ and 0.1 M KOH. It has been found that cycling the potential of active Ru electrode within E ranges 0 V–0.8 V and 0 V–1.2 V in 0.5 M H₂SO₄ and 0.1 M KOH solutions, respectively, leads to continuous electrode mass increase, while mass changes observed in alkaline medium are considerably smaller than those in acidic one. Microgravimetric response of active Ru electrode in 0.5 M H₂SO₄ within 0.2 V–0.8 V has revealed reversible character of anodic and cathodic processes. The experimentally found anodic mass gain and cathodic mass loss within 0.2–0.8 V make 2.2–2.7 g F^?1, instead of 17 g F^?1, which is the theoretically predicted value for Ru(OH)₃ formation according to equation: Ru+3H₂O?Ru(OH)₃+3H⁺+3e^?. In the case of Ru/RuO₂ electrode relatively small changes in mass have been found to accompany the anodic and cathodic processes within E range between 0.4 V and 1.2 V in the solution of 0.5 M H₂SO₄. Meanwhile cycling the potential of thermally formed RuO₂ electrode under the same conditions has lead to continuous decrease in electrode mass, which has been attributed to irreversible dehydration of RuO₂ layer. On the basis of microgravimetric and voltammetric study as well as the coulometric analysis of the results conclusions are presented regarding the nature of surface processes taking place on Ru and RuO₂ electrodes.     

Catalytic Effect on Silver Electrodeposition of Gold Deposited on Carbon Electrodes

A new methodology, based on silver electrocatalytic deposition and designed to quantify gold deposited onto carbon paste electrode (CPE) and glassy carbon electrode (GCE), has been developed in this work. Silver (prepared in 1.0 M NH₃) electrodeposition at ?0.13 V occurs only when gold is previously deposited at an adequate potential on the electrode surface for a fixed period of time. When a CPE is used as working electrode, an adequate oxidation of gold is necessary. This oxidation is carried out in both 0.1 M NaOH and 0.1 M H₂SO₄ at oxidation potentials. When a GCE is used as working electrode, the oxidation steps are not necessary. Moreover, a cleaning step in KCN, which removes gold from electrode surface, is included. To obtain reproducibility in the analytical signal, the surface of the electrodes must be suitably pretreated; this electrodic pretreatment depends on the kind of electrode used as working electrode. Low detection limits (5.0×10^?10 M) for short gold deposition times (10 min for CPE and 5 min for GCE) were achieved with this novel methodology. Finally, sodium aurothiomalate can be quantified using silver electrocatalytic deposition and GCE as working electrode. Good linear relationship between silver anodic stripping peak and aurothiomalate concentration was found from 5.0×10^?10 M to 1.0×10^?8 M.     

The electrochemistry of gold–platinum alloys

The electrochemical properties of gold, platinum and gold–platinum alloy electrodes under different heat treatment conditions have been studied in 0.5 M H₂SO₄ and 0.5 M NaOH. The electro-oxidation of 0.1 M ethylene glycol in 0.5 M NaOH at these electrodes has also been studied. It was found that all the gold–platinum electrodes are more active for ethylene glycol electro-oxidation than both pure gold and platinum, and that the gold–platinum electrodes in the solid solution condition are more active than the two-phase electrodes. Poisoning of all the electrodes occurs during electrolysis of ethylene glycol at a fixed potential. Potential pulsing is successful in removing the poisoning species formed at the pure gold and pure platinum electrodes. High apparent current densities are found during the first few cycles at the Au–Pt alloy electrodes. These high current densities are also associated with more severe poisoning – than at both pure gold and platinum – and longer cleaning cycles are needed to remove the poisons at these electrodes.     

Ni2+掺杂Ti/SnO2-Sb2O5电极的制备及性能

采用溶胶凝胶法制备了Ni2+掺杂的Ti/SnO2-Sb2O5电极,并通过XRD、SEM、EDS、苯酚降解、加速寿命实验等技术手段,研究了Ni2+的掺杂对电极的结构、形貌、电催化性能及稳定性的影响。结果表明:Ni2+的掺入细化了SnO2晶粒,增大了电极的比表面积,改善了电极表面的龟裂程度,提高了电极的导电性能;相对于Ti/SnO2-Sb2O5电极Ni2+的掺入将苯酚完全降解的时间缩短为原来的40%,将电极的使用寿命提高为原来的4.8倍。     

Anodic Stripping Voltammetric Detection of Arsenic(III) at Gold Nanoparticle‐Modified Glassy Carbon Electrodes Prepared by Electrodeposition in the Presence of Various Additives

The simple, fast and highly sensitive anodic stripping voltammetric detection of As(III) at a gold (Au) nanoparticle‐modified glassy carbon (GC) (nano‐Au/GC) electrode in HCl solution was extensively studied. The Au nanoparticles were electrodeposited onto GC electrode using chronocoulometric technique via a potential step from 1.1 to 0 V vs. Ag|AgCl|NaCl (sat.) in 0.5 M H₂SO₄ containing Na[AuCl₄] in the presence of KI, KBr, Na₂S and cysteine additives. Surfaces of the resulting nano‐Au/GC electrodes were characterized with cyclic voltammetry. The performances of the nano‐Au/GC electrodes, which were prepared using different concentrations of Na[AuCl₄] (0.05–0.5 mM) and KI additive (0.01–1.0 mM) at various deposition times (10–30 s), for the voltammetric detection of As(III) were examined. After the optimization, a high sensitivity of 0.32 mA cm^?2 μM^?1 and detection limit of 0.024 μM (1.8 ppb) were obtained using linear sweep voltammetry.     

Metal Oxide Film Anodes in the Electrolysis of Water or Brine

Metal (M) oxide (M: Ir, Os, Pd, Pt, Rh, Ru) together with MaO₂ and MnO₂ alone, were coated on SnO₂ films and the anode behavior was examined in 1.0 N H₂SO₄, 1.0 N NaOH and 1.0, N NaCl aqueous solutions at 25°. The results are compared with those of DSA and of metallic Pt.     

Studies on the calcium poisoning and regeneration of commercial De-NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> SCR catalyst

The poisoning effect of calcium on a commercial De-NO _x SCR catalyst (V₂O₅–WO₃/TiO₂) and the regeneration process of deactivated catalysts via water or H₂SO₄ washing were investigated under simulated condition in laboratory. The physicochemical properties of the catalysts were characterized by SEM–EDX, XRD, BET, TPD and FT-IR measurements, and the deactivation mechanism was discussed. The poisoning of calcium was attributed to the coverage of active sites and the reduction of acid sites on the surface of catalyst. The change of V=O bonds on catalyst surface was an important reason, which plays a significant role in the catalytic cycle of SCR. Due to the suction deliquescence of CaO to Ca(OH)₂, the catalytic activity of deactivated catalyst can be finitely recovered by water washing. Besides, as the result of the re-exposure of active sites by washing CaO off and the promotional effect of surface sulfation, the process of regeneration via sulfuric acid washing has a favorable effect in the experiment.     

原位化学沉积法制备碳/聚苯胺复合材料作为超级电容器材料的研究

Polyaniline （PA） film was chemically deposited onto the surface of activated carbon （AC） uniformly. Chemical deposition was carried out in 0.1 mol/L aniline plus 0.5 mol/L H2SO4 solution adopting V2O5·nH2O coated on the surface of activated carbon as oxidant. The surface morphologies and structures of the composite materials were characterized by scanning electron microscopy and FT-IR spectra. The electrochemical properties of the composite material electrodes were studied by cyclic voltammetry and constant current charge/discharge tests in 1 molFL H2SO4 solutions. The specific capacitance of composite materials was exhibited as high as 237.5 F/g at a current density of 1.0 A/g compared with a value of 120 F/g for pure carbon electrode. Good power characteristic and good stability of composite electrodes were also demonstrated.     

PbO<Subscript>2</Subscript>-SnO<Subscript>2</Subscript> composite anode with interconnected structure for the electrochemical incineration of phenol

A PbO₂-SnO₂ composite anode with interconnected structure is prepared for organics electro-incineration through a two-step method, thermal-decomposition process and subsequent low-current density electrodeposition process. The element mapping, together with the impedance spectra of the composite electrode, confirms that an interconnected architecture of SnO₂ and PbO₂ grains, instead of a lamellar structure, was obtained on the Ti substrate. A lower electrodeposition current density (≤10 mA cm⁻²) is very crucial for the formation of a porous surface and an interconnected architecture of two oxides inside. The asprepared electrode exhibits an enhanced electrocatalytic activity on the mineralization of phenol and a long service life due to the interconnected architecture, which helps to utilize the merits of these two metal oxides simultaneously. This two-step method also provides us a novel and facile way to fabricate a series of composite material such as oxide-oxide, oxide-metal composite electrodes.     

Electropolymerization of N,N-dimethylaniline in presence of sodium dodecyl sulfate and its electrochemical properties

Poly(N,N-dimethylaniline) (PDMA) was formed by successive cyclic voltammetry in monomer solution in the presence of sodium dodecyl sulfate (SDS) on the surface of a carbon paste electrode. The polymerization behavior of N,N-dimethylaniline in the presence of SDS is quite different from that of N,N-dimethylaniline in the absence of SDS. The effect of varying amount of SDS on the rate of polymerization of N,N-dimethylaniline was investigated. The electrochemical behavior of the SDS-PDMA carbon paste electrode has been investigated by cyclic voltammetry in 0.5 M H₂SO₄ and 5 mM K₄[Fe(CN)₆]/0.1 M KCl solutions as the supporting electrolyte and model system, respectively. The synthesized PDMA was characterized by FT-IR and scanning electron microscopy (SEM). Ni(II) ions were incorporated into the electrode by immersion of the polymeric modified electrode having amine groups in 0.1 M Ni(II) ion solution. The electro catalytic oxidations of methanol at the surface of the Ni/SDS-PDMA electrode were studied in a 0.1 M NaOH solution. Compared to bare carbon paste and PDMA-modified carbon paste electrodes; the SDS-PDMA electrode significantly enhanced the catalytic efficiency of Ni ions for methanol oxidation.     

The effect of platinum on the SnO<Subscript>2</Subscript> sorption properties

Chemisorption of SO₂ and O₂ at Pt-modified SnO₂ is studied by using the vacuum static method, with simultaneous recording of electrical conductivity, over the 22 to 300°C temperature range. The SnO₂ surface modification results in the increasing of SO₂ adsorption and weakening of the gas-surface bonding. The chemisorption enhances the samples’ electrical conductivity. The surface pretreatment with oxygen leads to the decreasing of the successive SO₂ chemisorption.     

Anodic oxidation of pentachlorophenol at Ti/SnO<Subscript>2</Subscript> electrodes

The electrochemical oxidation of dilute aqueous solutions of pentachlorophenol (PCP) using Ti/SnO₂ as an electrocatalytic material has been investigated. The studies were carried out in a two-compartment electrochemical cell at three different current density values (10, 30 and 50 mA cm^–2) at 25 °C and using 20 mg L^–1 of PCP in 0.1 M NaOH (pH 10) as supporting electrolyte. The PCP concentration and the by-products of the oxidized solution were monitored during the oxidation process using UV and HPLC techniques. For the three current densities investigated it was found that the rate of PCP elimination depends only on the specific electrical charge. Likewise, the oxidation mechanism was proved to occur through the participation of adsorbed hydroxyl radicals (·OH) formed on the SnO₂ surface, whatever the current density used. However, as the applied current density was increased, a current efficiency lower than 2% was obtained, which is due to mass transfer limitations. In addition, it was observed that the PCP was mineralized to CO₂ with conversion percentages as high as 92% and at current density values as low as 10 mA cm^–2. The PCP degradation produces two other by-products of oxidation (<10%), namely carboxylic acids, which are non-toxic compounds. Electronic Publication     

Nanoporous Pt Catalyst Modified by Sn Electrodeposition for Electrochemical Oxidation of Formaldehyde

A nanoporous Pt particles‐modified Ti (nanoPt/Ti) electrode was prepared through a simple hydrothermal method using aqueous H₂PtCl₆ as a precursor and formaldehyde as a reduction agent. The nanoPt/Ti electrode was then modified with limited amounts of tin particles generated by cyclic potential scans in the range of ?0.20 to 0.50 V in a 0.01 mol·L^?1 SnCl₂ solution, to synthesize a Sn‐modified nanoporous Pt catalyst (Sn/nanoPt/Ti). Electroactivity of the nanoPt/Ti and Sn/nanoPt/Ti electrodes towards formaldehyde oxidation in a 0.5 mol·L^?1 H₂SO₄ solution was evaluated by cyclic voltammetry and chronoamperometry. Electrooxidation of formaldehyde on the nanoPt/Ti electrode takes place at a potential of 0.45 V and then presents high anodic current densities due to the large real surface area of the nanoPt/Ti electrode. The formaldehyde oxidation rate is dramatically increased on the Sn/nanoPt/Ti electrode at the most negative potentials, where anodic formaldehyde oxidation is completely suppressed on the nanoPt/Ti electrode. Chronoamperogramms (CA) of the Sn/nanoPt/Ti electrode display stable and large quasi‐steady state current densities at more negative potential steps. Amperometric data obtained at a potential step of 100 mV show a linear dependence of the current density for formaldehyde oxidation upon formaldehyde concentration in the range of 0.003 to 0.1 mol·L^?1 with a sensitivity of 59.29 mA·cm^?2 (mol·L^?1)^?1. A detection limit of 0.506 mmol·L^?1 formaldehyde was found. The superior electroactivity of the Sn/nanoPt/Ti electrode for formaldehyde oxidation can be illustrated by a so‐called bifunctional mechanism which is involved in the oxidation of poisoning adsorbed CO species via the surface reaction with OH adsorbed on neighboring Sn sites.     

Solid‐State Electrochemical Method for Determining Core and Shell Size in Pd@PdO Nanoparticles

Electrochemical characterization of palladium nanoparticles surrounded by a palladium oxide shell (Pd@PdO) is described from a combination of voltammetry plus electrochemical quartz crystal microbalance experiments at nanoparticle deposits on graphite electrodes in contact with aqueous H₂SO₄ and NaOH solutions. A method for determining the metal core size and oxide shell thickness of the Pd@PdO nanoparticles, based on a combination of conventional voltammetry of nanoparticles in DMSO solution and voltammetry of nanoparticle deposits in contact with 0.10 M aqueous NaOH solution, is described.