Zur Kenntnis der Salpetersäure. X Methoden zur Gasanalyse im System N2−NO−NO2−N2O4−N2O3−HNO2−HNO3

Zusammenfassung Es werden vier Methoden zur Analyse einer Gasmischung N₂–NO–NO₂–N₂O₄–N₂O₃–HNO₂ besprochen und ihre Bedeutung für die Bestimmung der einzelnen Molekelarten kritisch auseinandergesetzt. Nach keiner der Methoden kann man den Gehalt an Salpetriger Säure und Salpetersäure neben den Oxyden des Stickstoffes auffinden. Aus diesem Grunde ist die Analyse der genannten Gasmischung nach den vier Methoden allgemein nicht genau durchführbar.Mit 1 Abbildung.Herrn Prof. Dr.A. Skrabal zum 75. Geburtstag gewidmet.     

Sintering, microstructures and dielectric properties of Ba1−xPbx(Ti1−xLix)O3−3xF3x ferroelectric ceramics

Various compositions (1−x)BaTiO₃ + xPbF2 + xLiF were prepared, shaped to pellets then sintered at 900°C for 2 h in gold sealed tubes. The purity and the symmetry of the obtained samples were checked by X-ray diffraction. A new solid solution with Ba_1−x Pb _x (Ti_1−x Li _x ) O_3−3x F_3x formula occurs in the composition range 0 ≤ x ≤ 0.20. SEM observations were performed on polished and fractured ceramics. The complex permittivity was measured as a function of temperature (−120°C ≤ T ≤ 250°C) and frequency (50 Hz ≤ f ≤ 4 × 10⁷ Hz). The dielectric performances are the best for ceramic Ba_0.97Pb_0.03(Ti_0.97Li_0.03)O_2.91F_0.09. The real component ε′, exhibits a maximum of approximately 7500 at the ferroelectric Curie temperature T _C ≈ -18°C, the dielectric losses tan δ value being 0.012. At room temperature, the relaxation frequency f _r is around 40 MHz for this ceramic. This novel ferroelectric oxifluoride is a promising material for applications, in particular in the field of Z5U multilayer capacitors.      

The Cl−NH3, Cl−H2O,F−NH3 and F−H2O clusters and their photoelectron spectra

The geometries of the Cl^–NH₃, Cl^–H₂O, F^–NH₃ and F^–H₂O clusters are optimized using the coupled cluster method. The four lowest ionization potentials are then calculated, leading to the ground and low excited states of the neutral species. The first three IPs describe ionization from the externalp state of the halogen atom, whereas the fourth corresponds to ionization from the NH₃ or H₂O moiety, leading to charge transfer complexes. These complexes were recently observed in the photoelectron spectrum of Cl^–NH₃, in full accord with our calculations.Supported in part by the U.S.-Israel Binational Science Foundation     

Chromatography of Anions on Alumina Thin Layers: Effect of Transition Metals on CI−-Br−-I− and No− 2-NO− 3 Separations

Abstract

Chromatographic behaviour of eighteen anions on thin layers of alumina and alumina mixed with silica gel (1:1, 1:2 and 2:1) has been studied using mixed acidic organic solvent systems containing formic acid. Though the addition of silica gel to alumina enhances the mobility and clarity of detection of anions, but it causes the increased tailing for Fe(CN)^3- ₆, Cr0₄ ^2- and Cr₂O₄ ^2-. Formic acid is responsible for the differential migration of anions. All the anions remained at the starting line (R_F = 0) in pure organic solvents. Formic acid-Ketone systems gave better results compared to formic acid-alcohol systems. Development time increases with the increase of viscosity/mol. wt. of organic solvents. The mutual separation of C1, Br^?, Br^?, I^? and NO^? ₂ and NO^? ₃ were achieved on pure alumina using formic acid-acetone solvent systems. The effect of transition metals (Ti, V, Cr, Mn, Fe, Co, Ni, Cu and Zn) on C1^?-Br^?-I^? and NO^? ₂-NO^? ₃ separations has been studied.     

Behavior of Mn3+ ions in four-layered hexagonal (Sr1−x−yLaxBay)MnO3

Stoichiometric four-layered hexagonal (4H) (Sr_1?x?yBa_xLa_y)MnO₃ was synthesized using a standard ceramic technique. Rietveld analysis at room temperature indicated that the Mn–O(1) distance increased and the Mn–O(2) distance decreased with the increase in x. The samples were n-type semiconductors and exhibited hopping conductivity in a small-polaron model below 533 K. The Mn³⁺ ion acted as a donor and the electron transfer became active through the Mn³⁺–O–Mn⁴⁺ path. The samples were antiferromagnetic and the Néel temperature (T_N) was constant regardless of y when x was fixed to 0.3, whereas T_N shifted to a high temperature when y was fixed to 0.02. The face-sharing Mn³⁺–O(2)–Mn⁴⁺ interaction strengthened as the Mn–O(2) distance decreased, and T_N shifted to a high temperature as a result.     

Mössbauer spectroscopic analysis of Bi1−xSrxFeO3−δ perovskites

Bi_1?xSr_xFeO_3?δ perovskites synthesised by solid-state reaction in ambient atmosphere or in a closed vessel were analysed by X-ray diffraction and Mössbauer spectroscopy. The evolution of the valence state of iron with both Bi/Sr ratio and oxygen content has been more particularly discussed. The samples are single phase and homogeneous for x ≤ 0.5 (Bi-rich) and x > 0.8 (Sr-rich). For intermediate Sr contents, the samples are less homogeneous and tend to contain both Bi-rich and Sr-rich phases. The appearance of Sr-rich phases for x > 0.5 corresponds to the appearance of Fe⁴⁺, to compensate for the lack of positive charges due to the replacement of Bi³⁺ by Sr²⁺.     

Gas-sensing properties of Ta-doped MoO3−x

During a search for alternative materials to replace tin(IV) oxide in semiconducting oxide gas sensors it has been found that sensors comprising sub-stoichiometric molybdenum trioxide exhibit promising characteristics.     

Facile synthesis of an optical sensor for CO32− and HCO3− detection

A novel fluorogenic signalling probe (E)-3-(4-methoxyphenyl)-4-[(4-nitrobenzylidene)amino]-1H-1,2,4-triazole-5(4H)-thione (6) for the carbonate and bicarbonate ions has been developed through microwave assisted Schiff base formation reaction. The anion recognition occurs through hydrogen bonding assessed by ¹H NMR titration experiments. The photophysical results of probe 6 corroborates its applicability as an optical sensing platform for carbonate as well as bicarbonate ions in mixed aqueous organic media depending on pH of reaction solution. The fluorescence emission signal enhancement at 424 nm and considerable shift in the signal position as well as molar absorptivity to the probe absorption bands upon CO₃^2? and HCO₃^? addition suggest the affinity of probe 6 towards these ions in comparison to a variety of competitive ions in aqueous/ethanol (7:3, v/v) at neutral pH and ambient temperature. From the fluorescence titration experiment, the limit of detection was calculated to be 1.91 μM.     

A Mössbauer spectroscopy investigation of SrFe1−xScxO3−δ perovskites

Polycrystalline samples of oxygen deficient perovskites SrFe_1?xSc_xO_3?δ (0 ≤ x ≤ 0.5) have been synthesized by direct solid state reactions. Each compound has been stabilized with two different oxygen stoichiometries. The structural study shows, firstly, the good cationic homogeneity of the samples and, secondly, that the Sc and Fe atoms are randomly distributed over the same crystallographic site, whatever the scandium content. This implies that no anionic order is possible. A detailed Mossbauer spectroscopy study clearly shows that the substitution of scandium for iron involves an oxygen content decrease which decreases the tetravalent iron content until its total disappearance for x = 0.5. The evolutions of the isomer shift, the quadrupolar splitting and the relative intensity versus the Sc³⁺ content are depicted in the present paper.     

Ab initio study of the HCO 3 − /H2O exchange in the (NH3)3 ZnII(HCO 3 − ) complex

Summary The displacement of bicarbonate anion in the (NH₃)₃Zn^II(HCO ₃ ^– ) complex with water has been studied throughab initio calculations. It has been found that H₂O binds to the (NH₃)₃Zn^II(HCO ₃ ^– ) species yielding a stable pentacoordinate (NH₃)₃Zn^II(HCO ₃ ^– )(H₂O) complex. The results also indicate that deprotonation of water in the pentacoordinate species facilitates the release of HCO ₃ ^– , although, the presence of HCO ₃ ^– in the coordination sphere of Zn^II makes such deprotonation more difficult. Environmental effects have been considered in the study of HCO ₃ ^– /H₂O exchange.A contribution from the Grup de Química Quàntica de l'Institut d'Estudis Catalans     

Separation and preconcentration of131I− and131IO 3 − in a liquid-liquid system

The application of isotope exchange in a liquid-liquid system for the separation and preconcentration of¹³¹I^– and¹³¹IO^3/– from water is described. For this purpose a solution of elemental iodine in tri-n-butyl phosphate diluted with toluene was used. The influence of various factors on the separation efficiency of¹³¹I was investigated. These are: time of the exchange, concentration of a carrier in the aqueous phase, concentration of I₂ in the organic phase, volume ratio of the phases, pH, foreign ions, storage of the organic phase, etc. The method is quite rapid and the selective preconcentration of these chemical forms of radioiodine from water can be accomplished even in the presence of the most important fission products. This method makes also possible to separate these chemical forms from each other under controlled pH conditions. The activity of the separated radioiodine can be measured advantageously, e.g., by homogeneous liquid scintillation counting after decolourization of the organic phase.     

Structure,nonstoichiometry and magnetic properties of the perovskites Sr1−xCaxMnO3−δ

The structural, thermal and magnetic properties of the perovskite-type alkaline-earth manganites of the series Sr_1−xCa_xMnO_3−δ (0⩽x⩽1) were investigated. SrMnO_3−δ forms a hexagonal perovskite lattice and shows a first-order transformation to a highly defective cubic high-temperature modification. By substituting Ca for Sr (x>0.25) the hexagonal perovskite is suppressed and a cubic (or orthorhombic) lattice becomes stabilized for all temperatures. For x=0.5 and 0.75 cubic perovskites with a large nonstoichiometry (e.g., δ=0.25 for x=0.5) are obtained at 1400 °C. The defective perovskites are prepared by either quenching from high temperature or by cooling in an inert atmosphere. The oxygen vacancies are easily filled by subsequent reoxidation at low temperature (400–600 °C) and stoichiometric samples are obtained. Orthorhombic perovskites are formed at T⩽1200 °C with the nonstoichiometry δ increasing with increasing temperature (e.g., δ=0.06 at 1000 °C and δ=0.14 at 1200 °C for x=0.5). Slow cooling in air results in almost complete reoxidation (δ=0). CaMnO_3−δ is an orthorhombic perovskite with a large range of nonstoichiometry (0⩽δ⩽0.30). The cubic to hexagonal phase transformation of the Sr-rich samples is accompanied by a large expansion of the lattice that is reduced by Ca substitution. The Ca/Sr-manganites are antiferromagnets with T_N of 170 K for x=0.5 and δ=0.02 and 120 K for x=1 and δ=0.05.     

Conduction mechanism in Y3−2xCa2xFe5−xVxO12 garnet ferrites

A series of polycrystalline garnet ferrites with composition Y_3−2xCa_2xFe_5−xV_xO₁₂ (x=0.0, 0.2, 0.4, 0.6, 0.8 and 1.0), were prepared by the standard ceramic technique to study the effect of Ca²⁺ and V⁵⁺ ions substitution on their DC electrical conductivity, thermoelectric power, charge carrier concentration and charge carrier mobility at different temperatures. It was found that the DC electrical conductivity increases linearly with increasing temperature ensuring the semiconducting nature of samples. The lines representing the temperature dependence of σ_dc are broken at two-phase transition temperature (T_σ1, T_σ2=T_C) giving three distinct regions (I, II and III). The activation energy for electrical conduction increases going from ferrimagnetic state (regions I and II) to paramagnetic state (region III) through the transition temperature T_σ2 (Curie temperature). It also increases going from region I to region II thorough the temperature T_σ1. The dc electrical conductivity does not vary uniformly with Ca²⁺ and V⁵⁺ ion substitution. The values of the thermoelectric power were positive for samples of 0.0⩽x⩽0.6 indicating that the majority of the carrier are holes in these samples while it were negative for samples of x⩾0.8 indicating that the majority of charge carriers are electrons in this samples. Using the values of the DC electrical conductivity and thermoelectric power, the values of the charge carrier concentration and the charge carrier mobility were calculated.     

Synthesis and properties of BaCe1−xYxO3−δ–BaWO4 composite protonic conductors

Barium cerate doped by trivalent rare earth metal ions is a potentially huge component of materials for electrochemical industry due to its high protonic conductivity. However, the poor chemical stability especially in the presence of CO₂, SO₂ or H₂O, resulting in decreasing the mechanical durability of obtained materials, limits their possible applications. The new approach towards stable ceramic protonic conductors with high electrical conductivity is presented. Thermal stability of yttrium doped (10 mol%) of BaCeO₃ was enhanced by forming the composite material BaCe_0.9Y_0.1O₃–BaWO₄ (10 mol% of BaWO₄). The synthesis was performed by solid-state reaction method. The detailed study of thermal decomposition of starting powders mixture was performed using thermogravimetry and differential thermal analysis (TG/DTA) techniques combined with Evolved Gas Analysis (EGA—mass spectrometry). Structure, phase composition and microstructure together with thermal stability of sintered materials were determined. The exposition tests were performed to characterise the stability of composites in carbon dioxide and water vapour-rich atmospheres. The samples were exposed to atmosphere containing CO₂/H₂O (7 % of CO₂ in air, 100 % RH) at temperature of 25 °C for 300 h. Thermal analysis supplied with mass spectrometry was applied to analyse the materials after the test. The results of this experiment showed better chemical resistance of composite material—BaCe_0.9Y_0.1O₃ with 10 mol% of BaWO₄ compared to single phase material.     

Carbon-free D3d [E3ME3]2− (E=P, As; M=Ni, Pd, Pt): The smallest inorganic sandwich complexes with aromatic η3-P 3 − and η3-As 3 − ligands

A density functional theory and wave function theory investigation on the possibility of carbon-free phosphametallocenes [P₃MP₃]^2? and arsenametallocenes [As₃MAs₃]^2? (M=Ni, Pd, Pt) is presented in this work. Staggered singlet D_3d [E₃ME₃]^2? (E=P, As)-the smallest inorganic metallocenes possible to construct-proved to be the global minima of the heptaatomic systems and may be targeted in future experiments. Cyclo-P ₃ ^? and cyclo-As ₃ ^? turned out to possess similar aromaticity to cyclo-P ₅ ^? and cyclo-As ₅ ^? and may serve as effective ligands to sandwich a wide range of transition metals. The first vertical electron detachment energies of C_s [E₃ME₃]Li^? monoanions with a staggered [E₃ME₃]^2? sandwich core were predicted to be between 2.7 and 2.9 eV; the extent of stabilization by Li⁺ suggests that such materials be viable targets for experimental characterization.     

Thermochemical investigations of the systems KCl−KBr−H2O,K2SO4−(NH4)2SO4−H2O and KNO3−NH4NO3−H2O at 298.15 K

For the equilibrium solid phases occurring in the systems: KCl?KBr?H₂O, K₂SO₄?(NH₄)₂SO₄?H₂O and KNO₃?NH₄NO₃?H₂O, the concentration dependencies of differential solution enthalpies, Δ_sol H ₂ for several crystallization paths, were measured. The limiting differential solution enthalpies, Δ_sol H ₂ ⁰ , were determined by extrapolation of the above dependencies to the ionic strength,I _m ⁰ , corresponding to the appropriate binary solutions. For KCl?KBr?H₂O system only, the clear dependence between Δ_sol H ₂ ⁰ andI _m ⁰ values was found and discussed.     

Untersuchungen in den Systemen: V−B,Nb−B,V−B−Si und Ta−B−Si

Zusammenfassung Mit Hilfe röntgenographischer Messungen werden die Boride von Vanadin und Niob untersucht, wobei eine neue Phase der ungefähren Zusammensetzung V₂B identifiziert wird, welche mit der entsprechenden Nb-Borid-Phase isotyp ist. Dieselbe Kristallart tritt auch im System: Ta–B auf. Die in der Literatur angegebene -Phase im Zweistoff: Nb–B erweist sich als NbO.Im System: V–B–Si wird wie im analogen Mo-System die Existenz einer ternärenT 2-Phase Me₅(Si_1/3, B_2/3)₃ nach-gewiesen¹; ihre Gitterkonstanten werden ermittelt.Im Schnitt Ta₂Si–Ta₂B besteht ein geringes Lösungs-vermögen der beiden Phasen ineinander. Durch Zusatz von 20 Mol-% Ta₂Si zu Ta₂B erhält man die oben erwähnte neue Kristallart.Bei den Borid-Siliziden der Metalle aus der 4a-, 5a- und 6a-Gruppe werden die Stabilitätsbereiche derT 1-,T 2- undD 8₈-Phasen miteinander verglichen.