Plasma-induced graft-polymerisation of ethylene glycol methacrylate phosphate on polyethylene films

A detailed study of argon plasma-induced graft-polymerisation of ethylene glycol methacrylate phosphate (EGMP) on polyethylene (PE) substrates is presented. The process consists of four steps: (a) plasma pre-activation of the PE substrates; (b) immersion in an EGMP solution; (c) argon plasma-induced graft-polymerisation; (d) washing and drying of the samples. Influence of the solution and plasma parameters on the process efficiency, evaluated in terms of amount of grafted polymer and coverage uniformity, is investigated. The plasma-induced graft-polymerisation of EGMP is then followed by sample weighting, contact angle measurements, attenuated total reflection infrared (ATR-IR) spectroscopy and X-ray photoelectron spectroscopic (XPS) analysis. Finally, flame-retardant properties of modified PE substrates are evaluated by limiting oxygen index (LOI) measurements.     

Preparation of quaternized dimethylaminoethylmethacrylate grafted nonwoven fabric for the removal of phosphate

Dimethylaminoethylmethacrylate (DMAEMA) grafted polyethylene/polypropylene (PE/PP) nonwoven fabric was prepared by radiation-induced graft polymerization. Grafting conditions were optimized and about 150% DMAEMA grafted samples were used for further experiments. DMAEMA graft chains were later quaternized with dimethyl sulphate for the removal of phosphate ions. Adsorption experiments were conducted with quaternized DMAEMA grafted fabric for phosphate removal at low (0.5–25 ppm) and high phosphate concentrations (50–1000 ppm). Adsorbed phosphate amounts at pH 7 were found to be 63 mg phosphate/g polymer and 512 mg phosphate/g polymer for low (25 ppm) and high phosphate concentrations (1000 ppm) respectively showing the efficiency of the adsorbent material in removing phosphate. The pH effect on phosphate adsorption showed that the quaternized DMAEMA grafted nonwoven fabric can adsorb phosphate over a wide pH range (5.00–9.00) indicating that adsorbent material can effectively remove different forms of phosphate ions, namely H₂PO₄^?, HPO₄^2? and PO₄^3? in aqueous solution at this pH range where the species exist. Competitive adsorption experiments were also carried out with two concentration levels at pH 7 to investigate the effect of competing ions. Phosphate adsorption on quaternized DMAEMA grafted nonwoven fabric was found to be higher than the other competing ions at two concentration levels. At high concentration level, the adsorption order was phosphate>nitrite>bromide>sulphate>nitrate whereas at low concentration level, the order was phosphate?sulphate>bromide>nitrite>nitrate.     

Temperature- and pH-sensitive interpenetrating polymer networks grafted on PP: Cross-linking irradiation dose as a critical variable for the performance as vancomycin-eluting systems

This work focuses on the effect of gamma-ray radiation conditions on the stimuli-responsiveness and drug-eluting performance of polypropylene (PP) substrates grafted with interpenetrating networks of N-isopropylacrylamide (NIPAAm) and acrylic acid (AAc). PNIPAAm was cross-linked applying 10–100 kGy doses in the presence and absence of the chemical cross-linker N,N′-methylenebisacrylamide (MBAAm). Then, the net-PP-g-PNIPAAm was interpenetrated with PAAc synthesized under a 2.5 kGy dose to obtain net-PP-g-PNIPAAm-inter-net-PAAc films. The amount of grafted PNIPAAm (80%, 125% and 145% levels) and the cross-linking radiation dose (10, 40 and 70 kGy levels) strongly determine the interpenetration of PAAc, the swelling degree, the amount of vancomycin loaded and its release rate. The chemical cross-linker only caused a minor decrease in the degree of swelling. The higher the PNIPAAm grafted on PP and the lower the cross-linking radiation dose, the more the PAAc in the IPN and, consequently, the higher the vancomycin loaded through specific interactions and the more sustained the release (>8 h). The films possessing these features exhibited vancomycin release rate per surface unit suitable to prevent bacterial growth. Thus, adequate tuning of the radiation doses during grafting and cross-linking of the PNIPAAm networks may enable to achieve surface-modified materials for medical devices with an antibiofilm performance.     

Antifouling properties of poly(methyl methacrylate) films grafted with poly(ethylene glycol) monoacrylate immersed in seawater

Biofouling of all structures immersed in seawater constitutes an important problem, and many strategies are currently being developed to tackle it. In this context, our previous work shows that poly(ethylene glycol) monoacrylate (PEGA) macromonomer grafted on preoxidized poly(methyl methacrylate) (PMMAox) films exhibits an excellent repellency against the bovine serum albumin used as a model protein. This study aims to evaluate the following: (1) the prevention of a marine extract material adsorption by the modified surfaces and (2) the antifouling property of the PEGA-g-PMMAox substrates when immersed in natural seawater during two seasons (season 1: end of April-beginning of May 2007, and season 2: end of October-beginning of November 2007). The antifouling performances of the PEGA-g-PMMAox films are investigated for different PEG chain lengths and macromonomer concentrations into the PEGA-based coatings. These two parameters are followed as a function of the immersion time, which evolves up to 14 days. The influence of the PEGA layer on marine compounds (proteins and phospholipids) adsorption is evidenced by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS). It was found that the antifouling efficiency of the PEGA-grafted surfaces increases with both PEGA concentration and PEG chain length.     

Preparation of poly(ether ether ketone)-based polymer electrolytes for fuel cell membranes using grafting technique

Poly(ether ether ketone) (PEEK)-based polymer electrolyte membranes (PEMs) was successfully prepared by radiation grafting of a styrene monomer into PEEK films and the consequent selective sulfonation of the grafting chains in the film state. Using milder sulfonation, the sulfonation reactions proceeded at the grafted chains in preference to the phenylene rings of PEEK main chains; as a result, the grafted films could successfully transform to a PEM with conductivity of more than 0.1 S/cm. The ion exchange capacity (IEC) and conductivity of the grafted PEEK electrolyte membranes were controlled to the ranges of 1.2–2.9 mmol/g and 0.03–0.18 S/cm by changing the grafting degree. It should be noted that this is the first example of directly transforming super-engineering plastic films into a PEM using radiation grafting.     

Enthalpies of adsorption of metal atoms on single-crystalline surfaces by microcalorimetry

The heats of adsorption of metal gas atoms onto single crystalline surfaces can be measured directly as a detailed function of coverage using a unique microcalorimeter. The development of this experimental apparatus and the results obtained from these experiments will be reviewed. The heat detection is performed with a highly sensitive pyroelectric polymer ribbon pressed into contact with the thin (1 μ m thick) single crystal sample, onto which pulses of a metal atom beam impinge. Heats of adsorption have been measured for pulses of gas containing a few per cent of a monolayer with a pulse-to-pulse standard deviation as low as 1.5 kJ · mol ^− 1. The adhesion energy of multilayer metal films can be estimated from the integral enthalpy of adsorption.     

Influence of maleic anhydride grafted polypropylene on the miscibility of polypropylene/polyamide-6 blends using ATR-FTIR mapping

In this work we describe an approach to study the influence of the compatibilizer, maleic anhydride grafted polypropylene (PP-g-MAH), on the miscibility of polypropylene/polyamide-6 blends (PP/PA6) using attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopic mapping. In measurement, the image area for each blend was 100 μm × 100 μm. Different amounts of PP-g-MAH were introduced into the polymer blends, and the miscibility was characterized by the spatial distribution of PA6 in the image based on the corrected absorbance at 1640 cm^?1. It was found that small quantities of the compatibilizer could significantly improve the miscibility of the two immiscible polymers. Furthermore, our results proved that blend with 6 parts of PP-g-MAH by weight exhibited an optimal miscibility behavior. This paper demonstrates that ATR-FTIR mapping is a direct method to visualize the miscibility of polymer blends.     

Adsorption behaviour and surfactant elution of cationic salivary proteins at solid/liquid interfaces,studied by in situ ellipsometry

Adsorption of the cationic salivary proteins lactoferrin, lactoperoxidase, lysozyme and histatin 5 to pure (hydrophilic) and methylated (hydrophobized) silica surfaces was investigated by in situ ellipsometry. Effects of concentration (≤10 μg ml⁻¹, for lysozyme ≤200 μg ml⁻¹) and dependence of surface wettability, as well as adsorption kinetics and elutability of adsorbed films by buffer and sodium dodecyl sulphate (SDS) solutions were investigated. Results showed that the amounts adsorbed decreased in the order lactoferrin ≥ lactoperoxidase > lysozyme ≥ histatin 5. On hydrophilic silica, the adsorption was most likely driven by electrostatic interactions, which resulted in adsorbed amounts of lactoferrin that indicated the formation of a monolayer with both side-on and end-on adsorbed molecules. For lactoperoxidase the adsorbed amounts were somewhat higher than an end-on monolayer, lysozyme adsorption showed amounts corresponding to a side-on monolayer, and histatin 5 displayed adsorbed amounts in the range of a side-on monolayer. On hydrophobized substrata, the adsorption was also mediated by hydrophobic interactions, which resulted in lower adsorbed amounts of lactoferrin and lactoperoxidase; closer to side-on monolayer coverage. For both lysozyme and histatin 5 the adsorbed amounts were the same as on the hydrophilic silica. The investigated proteins exhibited fast adsorption kinetics, and the initial kinetics indicated mass transport controlled behaviour at low concentrations on both types of substrates. Buffer rinsing and SDS elution indicated that the proteins in general were more tightly bound to the hydrophobized surface compared to hydrophilic silica. Overall, the surface activity of the investigated proteins implicates their importance in the salivary film formation.     

Grafting copolymerization of polyethylene glycol methacrylate (PEGMA) onto preirradiated PP films

Polyethylene glycol methacrylate (PEGMA) with different polyethylene oxide units were grafted onto polypropylene (PP) films by a preirradiation grafting method. The effect of co-solvent system on the degree of grafting and water contact angle were determined, respectively. The grafted sample films were verified by Fourier Transform Infrared (FTIR) spectroscopy in the attenuated total reflectance mode (ATR). The biocompatibility and blood compatibility of the grafted PP films were evaluated by the determination of protein adsorption, platelet adsorption and thrombus.     

Nanomechanical properties of polymer brushes by colloidal AFM probes

Nanomechanical properties of end grafted polymer layers were studied by AFM based, colloidal probe compression measurements. Zwitterionic poly(sulfobetaine methacrylate) (PSBMA) brush was grafted from planar Si surface and poly(methyl methacrylate) (PMAA) brush was grown on colloidal probe by surface initiated atom transfer radical polymerization. PMAA brush was further modified with adhesion promoting arginyl-glycyl-aspartic acid (RGD) peptide sequences. Force–distance curves were obtained for systems where the polymer brushes were probed on unmodified surfaces or face to each other. For each systems the grafting density of the polymer brush was determined applying a ‘box’ like polymer brush model based on the theory by de Gennes. ‘Average’ grafting density was calculated in cases when two polymer brushes face each other: RGD functionalized PMAA or PMAA against PSBMA. For our systems the values for the grafting density was between 0.04 and 0.11 nm^?2. Furthermore the measured approach force–distance curves were fitted according to the Hertz model and the apparent Young’s modulus was determined for all measurements being in a range of around 250 kPa at physiological conditions.     

Efficiency of blocking of non-specific interaction of different proteins by BSA adsorbed on hydrophobic and hydrophilic surfaces

The efficiency of a pre-absorbed bovine serum albumin (BSA) layer in blocking the non-specific adsorption of different proteins on hydrophobic and hydrophilic surfaces was evaluated qualitatively and quantitatively using infrared reflection spectroscopy supported by spectral simulations. A BSA layer with a surface coverage of 35% of a close-packed monolayer exhibited a blocking efficiency of 90–100% on a hydrophobic and 68–100% on a hydrophilic surface, with respect to the non-specific adsorption of concanavalin A (Con A), immunoglobulin G (IgG), and staphylococcal protein A (SpA). This BSA layer was produced using a solution concentration of 1 mg/mL and 30 min incubation time. BSA layers that were adsorbed at conditions commonly employed for blocking (a 12 h incubation time and a solution concentration of 10 mg/mL) exhibited a blocking activity that involved competitive adsorption–desorption. This activity resulted from the formation of BSA–phosphate surface complexes, which correlated with the conformation of adsorbed BSA molecules that was favourable for blocking. The importance of optimisation of the adsorbed BSA layer for different surfaces and proteins to achieve efficient blocking was addressed in this study.     

Study of the morphology,thermal and mechanical properties of irradiated isotactic polypropylene films

Thin films of isotactic polypropylene (iPP) are of great economical importance and their production is quite challenging due to the need of very fast uniaxial or biaxial expansion. During the expansion, critical problems usually arise, like structure disruption, shear thinning, causing material, energy and time losses. This work aims to study the surface morphology and compare the thermal, mechanical properties of PP films irradiated by gamma ray in an acetylene atmosphere after uniaxial expansion. PP films were made by compression molding at 190 °C with cooling in water at room temperature and irradiated by gamma ray, at (5, 12.5 and 20 kGy) under acetylene atmosphere. After irradiation the samples were submitted to thermal treatment at 90 °C for 1 h and then stretched out at 170 °C using an Instron machine. The surface of PP films, pristine and modified, (i.e., irradiated), was studied using optical microscopy (OM) and scanning electron microscopy (SEM). The changes in morphology, crystallinity and tensile parameters, like yield stress, rupture stress and elongation strain of the PP with irradiation dose were investigated. The results showed some evidences of gel formation due to crosslinking and/or long chain branching induced by radiation.     

Polymeric nanocapsules ultra stable in complex biological media

Non-specific protein adsorption from complex biological media, especially from blood plasma, is an urgent challenge for the application of nanoparticles as delivery systems, diagnostics, and other biomedical application. Nanocapsules (NC) prepared from FDA-approved degradable poly(ɛ-caprolactone) shell and Mygliol 812^® oil in the core were coated with mono-methoxy terminated oligo(ethylene glycol) methacrylate (poly(MeOEGMA)) polymer brush layers with a well-controlled thickness at the nanometer scale up to 350 nm using surface initiated atom transfer radical polymerization in water or phosphate buffered saline. Incubation of uncoated NC with human serum albumin solution, fetal bovine serum, or human blood plasma resulted in fast aggregation observed by dynamic light scattering as an increase in diameter of particles present in the solutions. Conversely, these biological fluids affected only marginally the size distribution of the NC coated with a 60 nm thick poly(MeOEGMA) layer. The high suspension stability of the coated NC in complex biological fluids was related to the suppressed deposition of proteins from these fluids observed by surface plasmon resonance (SPR) on analogous poly(MeOEGMA) layer prepared on flat surfaces of SPR chips.     

TEMPO addition into pre-irradiated fluoropolymers and living-radical graft polymerization of styrene for preparation of polymer electrolyte membranes

We prepared proton exchange membranes (PEMs) by 2,2,6,6-tetramethylpiperidinyl-1-oxy (TEMPO)-mediated living-radical graft polymerization (LRGP) of styrene into fluoropolymer films and subsequent sulfonation. Poly(vinylidene fluoride) (PVDF) and poly(ethylene-co-tetrafluoroethylene) (ETFE) films were first irradiated and then treated with TEMPO solutions in various solvents. TEMPO addition was confirmed by the test of styrene grafting into TEMPO-treated films at 60 °C, at which the LRGP never proceeds. This test enabled us to differentiate the LRGP from the conventional graft polymerization. In order to gain a deep insight about TEMPO-addition reaction, the TEMPO-penetration behavior into the base polymer films was examined by a permeation experiment and computer simulation. Xylene and dioxane were appropriate solvents for the complete introduction of TEMPO into PVDF and ETFE films, respectively. Then, the LRGP of styrene was performed based on the fully TEMPO-capped films at 125 °C with various solvents. By using an alcoholic solvent, the degree of grafting was enhanced and it reached a maximum of 38%. This grafted film was sulfonated to prepare a PEM showing an ion exchange capacity of 2.2 meq/g and proton conductivity of 1.6×10^?1 S/cm.     

Fabrication of crystallized boron films by laser ablation

Polycrystalline β-rhombohedral boron films mixed with amorphous boron phase have been successfully fabricated on quartz substrates using pulsed laser ablation in a quartz glass tube chamber placed in an electric furnace. The crystallinity of the films strongly depended on the temperature of the furnace and the pressure of background argon gas. High temperature and high pressure in the chamber were suitable for crystallized boron film preparation. The best crystalline films (without B₂O₃ phase formation) were obtained at 1000°C, 100 Pa. XPS measurements demonstrated that the major contaminants were carbon and oxygen, and the atomic ratio of oxygen to boron was 0.05 under the preparation conditions of well-crystallized films. The surface roughness of the films decreased by lowering laser energy to 150 mJ/pulse under the same pressure and temperature conditions.     

Poly (vinyl alcohol – aniline) water soluble composite as corrosion inhibitor for mild steel in 1 M HCl

Poly (vinyl alcohol – aniline) PVAA composite was tested for its performance in protecting mild steel MS against corrosion in 1 M HCl. The inhibitive parameters were evaluated by means of weight loss, electrochemical polarization and impedance methods. Results indicated that the addition of PVAA to the acid reduces the corrosion of the metal. Inhibition efficiency increases with increase in inhibitor concentration. The results further revealed that PVAA at a concentration of 2000 ppm furnishes a maximum of 92% inhibition efficiency. Thermodynamic parameters such as free energy of adsorption, heat of adsorption, etc., had been evaluated from temperature studies. The adsorption of PVAA followed Langmuir and Temkin adsorption isotherms. Polarization curves revealed that PVAA is a mixed inhibitor.     

Adsorption of Cr(VI) using cellulose microsphere-based adsorbent prepared by radiation-induced grafting

Cellulose microsphere (CMS) adsorbent was prepared by radiation-induced grafting of dimethylaminoethyl methacrylate (DMAEMA) onto CMS followed by a protonation process. The FTIR spectra analysis proved that PDMAEMA was grafted successfully onto CMS. The adsorption of Cr(VI) onto the resulting adsorbent was very fast, the equilibrium adsorption could be achieved within 15 min. The adsorption capacity strongly depended on the pH of the solution, which was attributed to the change of both the existed forms of Cr(VI) and the tertiary-ammonium group of PDMAEMA grafted CMS with the pH. A maximum Cr(VI) uptake (ca. 78 mg g^?1) was obtained as the pH was in the range of 3.0–6.0. However, even in strong acid media (pH 1.3), the adsorbents still showed a Cr(VI) uptake of 30 mg g^?1. The adsorption behavior of the resultant absorbent could be described with the Langmuir mode. This adsorbent has potential application for removing heavy metal ion pollutants (e.g. Cr(VI)) from wastewater.     

Adsorption of hydrogen on Pt(1 1 1) and Pt(1 0 0) surfaces and its role in the HOR

Hydrogen adsorption isotherms, evaluated by combination of cyclic voltammetry and chronoamperometry, are reported on Pt(1 1 1) and Pt(1 0 0) surfaces in 0.1 M HClO₄. We found that at E > 0.05 V Pt(1 1 1) and Pt(1 0 0) are only partially covered by the adsorbed hydrogen (H_ad). On both surfaces, a full monolayer of the adsorbed hydrogen is completed at −0.1 V, i.e. the adsorption of atomic hydrogen is observed in the hydrogen evolution potential region. We also found, that the activity of the hydrogen oxidation reaction is mirrored by the shape of the hydrogen adsorption isotherms, implying that H_ad is in fact a spectator in the HOR.     

Effect of compressed CO2 on crystallization and melting behavior of isotactic polypropylene

Compressed gases such as CO₂ above their critical temperatures provide a highly tunable technique that has been shown to induce changes in phase behavior, crystallization kinetics and morphology of the polymers. Gas induced plasticization of the polymer matrix has been studied in a large number of polymers such as polystyrene, and poly(ethylene terephathalate). The knowledge of polymer–gas interactions is fundamental to the study of phenomena such as solubility and diffusivity of gases in polymers, dilation of polymers and in the development of applications such as foams and barrier materials.In this paper, we describe the interactions of compressed CO₂ with isotactic polypropylene (PP). Crystallization of various PPs in presence of compressed CO₂ was evaluated using a high pressure differential scanning calorimeter (HPDSC). CO₂ plasticized the polymer matrix and decreased the crystallization temperature, T_c by ∼8 °C for PP at a pressure of 650 psi CO₂. The decrease as a function of pressure was −0.173 °C/bar and did not change with the molecular architecture of PP. Both crystallization kinetics and melting behavior are evaluated.Since solubility and diffusivity are important thermodynamic parameters that establish the intrinsic gas transport characteristics in a polymer, solubility of CO₂ in PP was measured using a high-pressure electrobalance and compared with cross-linked polyethylene. At 50 °C, solubility followed Henry’s law and at a pressure of 200 psi about 1% CO₂ dissolved in PP. Similar solubility was achieved in PE at a pressure of 160 psi. Higher solubility of CO₂ in PE is attributed to its lower crystallinity and lower T_g, than PP. Diffusion coefficients were calculated from the sorption kinetics using a Fickian transport model. Diffusivity was independent of pressure and PE showed higher diffusivity than PP. Preliminary foaming studies carried out using a batch process indicate that both PP and PE can be foamed from the solid state to form microcellular foams. Cell size and cell density were ∼10 μm and 10⁸ cells/cm³, respectively in PE. Differences in morphology between the foams for these polymers are attributed to the differences in diffusivity.     

Excited states in the alkali/noble metal surface systems: A model system for the study of charge transfer dynamics at surfaces

The low coverage adsorption of alkalis on metal surfaces induces excited states localised on the adsorbate. In the case of noble metal substrates, these excited states can exhibit a very long lifetime, up to tens of fs in the Cs/Cu(1 1 1) system. We review recent experimental and theoretical investigations of alkalis adsorbed on noble metal surfaces, with emphasis on the characteristics of the alkali-induced excited states, the origin of their long lifetimes, and the consequences for the adsorbate dynamics. The possibility of long-lived resonances in other adsorbate/substrate systems is also discussed.