Assessment of shunted piezoelectric devices for simultaneous noise and vibration reduction: comparison of passive,active and hybrid networks

Structural vibration and noise control of a cavity-backed three-layered smart piezo-coupled rectangular panel system under harmonic or transient loads is achieved by using purely active, passive, and hybrid active/passive piezoelectric shunt networks. Problem formulation is based on the classical lamination plate theory, Maxwell’s equation for piezoelectric materials, linear circuit theory, and wave equation for the enclosed acoustic domain. The orthogonal mode expansions along with the modal coupling theory are employed to obtain the coupled differential equations of the electro-mechanical-acoustic system, which are then put into the convenient state-space form, and subsequently solved numerically in both frequency and time domains. A triple-mode hybrid RLC shunt circuit, in series with an external active voltage source and connected to a single electroded piezoelectric segment, is tuned to the dominant resonance frequencies of the composite structure. The linear quadratic optimal control (LQR) theory is adopted for obtaining the active control gains. The frequency and time domain performances of the passive, active and hybrid multi-modal piezoelectric systems are calculated and discussed in terms of sensor output voltage, local sound pressure, and control effort. It is found that the hybrid control methodology with properly tuned circuit parameters can be an excellent candidate for simultaneous vibration and structure-borne noise control of the cavity-coupled smart panel with decreased control effort. Also, the active control strategy integrated in the hybrid control system is demonstrated to enhance the overall system damping characteristics and improve the control authority at frequencies where the passive shunt network performs weakly. Limiting cases are considered and correctness of the mathematical model is verified by using a commercial finite element software as well as by comparisons with the literature.     

Design of an Active Noise Control System Using a Distributed Actuator

A distributed acoustic actuator for active noise control, consisting of a piezoelectric PVDF film, bonded at each side of a carrier structure, is simulated and built. The piezoelements are driven in anti-phase, resulting in a bending motion of the actuator, and thus in the necessary out-of-plane displacement for sound radiation. An analytical model for the acoustic actuator is derived, relating the actuator's displacement to the applied voltage, taking into account the influence of the piezoelectric film on the actuator's stiffness. The model is used to optimise the specifications for the piezoelectric film and the carrier structure, resulting in the highest sound power output in a frequency range from 30–500 Hz. An analytical model for the behaviour of a double panel partition is derived. The analytical model is combined with the model for the acoustic actuator, describing an actively controlled double panel partition with a distributed acoustic actuator integrated in the cavity. A controller is added to the system to control the sound power transmitted through the double panel partition. Simulation results show that a substantial increase of transmission loss can be achieved in the low frequency region (30–500 Hz) with this configuration. This revised version was published online in July 2006 with corrections to the Cover Date.     

Vibration and damping analysis of a composite plate with active and passive damping layer

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｃｏｎｖｅｎｔｉｏｎａｌｐａｓｓｉｖｅｃｏｎｓｔｒａｉｎｅｄｌａｙｅｒｄａｍｐｉｎｇ（ＰＣＬＤ）ｔｒｅａｔｍｅｎｔｓｈａｖｅｂｅｅｎｅｘｔｅｎｓｉｖｅｌｙｕｔｉｌｉｚｅｄａｓａｓｉｍｐｌｅａｎｄｒｅｌｉａｂｌｅｍｅａｎｓｆｏｒｄａｍｐｉｎｇｏｕｔｔｈｅｖｉｂｒａｔｉｏｎｏｆｖａｒｉｏｕｓｓｔｒｕｃｔｕｒｅｓ（ＭｅａｄａｎｄＭａｒｋｕｓ１９６９［１］,Ｙ．Ｋ．Ｃｈｅｕｎｇ１９７２［２］,ＪｏｈｎｓｏｎａｎｄＫｉｅｎｈｏｌｚ１９８２［３］,ＣｕｐｉａｌａｎｄＮｉｚｉｏｌ…     

两层压电换能器之间的电能传输

采用双层压电板近似模拟两个压电换能器，一层模拟发射声波的驱动换能器，另一层模拟接收声波并转换为电能的接收换能器，通过对压电板的分析，求解了两压电换能器之间的电能传输效率及其对系统参数的依赖关系，得到了输出电压、输出功率和传输效率与系统参数之间的明确关系式。最后，通过计算实例，分析了系统参数对结构功能的影响规律。     

COUPLED ANALYSIS FOR THE HARVESTING STRUCTURE AND THE MODULATING CIRCUIT IN A PIEZOELECTRIC BIMORPH ENERGY HARVESTER

The authors analyze a piezoelectric energy harvester as an electro-mechanically coupled system. The energy harvester consists of a piezoelectric bimorph with a concentrated mass attached at one end, called the harvesting structure, an electric circuit for energy storage, and a rectifier that converts the AC output of the harvesting structure into a DC input for the storage circuit. The piezoelectric bimorph is assumed to be driven into flexural vibration by an ambient acoustic source to convert the mechanical energies into electric energies. The analysis indicates that the performance of this harvester, measured by the power density, is characterized by three important non-dimensional parameters, i.e., the non-dimensional inductance of the storage circuit, the non-dimensional aspect ratio （length/thickness） and the non-dimensional end mass of the harvesting structure. The numerical results show that： （1） the power density can be optimized by varying the non-dimensional inductance for each fixed non-dimensional aspect ratio with a fixed non-dimensional end mass; and （2） for a fixed non-dimensional inductance, the power density is maximized if the non-dimensional aspect ratio and the non-dimensional end mass are so chosen that the harvesting structure, consisting of both the piezoelectric bimorph and the end mass attached, resonates at the frequency of the ambient acoustic source.     

Vibration analysis of FG annular sector in moderately thick plates with two piezoelectric layers

Free vibration of functionally graded(FG) annular sector plates embedded with two piezoelectric layers is studied with a generalized differential quadrature(GDQ)method. Based on the first-order shear deformation(FSD) plate theory and Hamilton's principle with parameters satisfying Maxwell's electrostatics equation in the piezoelectric layers, governing equations of motion are developed. Both open and closed circuit(shortly connected) boundary conditions on the piezoelectric surfaces, which are respective conditions for sensors and actuators, are accounted for. It is observed that the open circuit condition gives higher natural frequencies than a shortly connected condition. For the simulation of the potential electric function in piezoelectric layers, a sinusoidal function in the transverse direction is considered. It is assumed that properties of the FG material(FGM) change continuously through the thickness according to a power distribution law.The fast rate convergence and accuracy of the GDQ method with a small number of grid points are demonstrated through some numerical examples. With various combinations of free, clamped, and simply supported boundary conditions, the effects of the thicknesses of piezoelectric layers and host plate, power law index of FGMs, and plate geometrical parameters(e.g., angle and radii of annular sector) on the in-plane and out-of-plane natural frequencies for different FG and piezoelectric materials are also studied. Results can be used to predict the behaviors of FG and piezoelectric materials in mechanical systems.     

Resonant vibrations of a clamped thermoviscoelastic rectangular plate with sensors and actuators

The paper discusses the active damping of the resonant flexural vibrations of a clamped thermoviscoelastic rectangular plate with distributed piezoelectric sensors and actuators. The thermoviscoelastic behavior of the passive and active materials is described using the concept of complex characteristics. The interaction of the mechanical and thermal fields is taken into account. The Bubnov–Galerkin method is used. The effect of self-heating, the dimensions of the piezoelectric inclusions, and the feedback factor on the effectiveness of active damping of the resonance vibrations of the plate is studied     

Damping the flexural vibration of a clamped viscoelastic rectangular plate with piezoelectric actuators

The paper addresses the active damping of the resonant flexural vibration of a clamped viscoelastic rectangular plate with distributed piezoelectric actuators. The thermomechanical behavior of passive and active materials is described using the concept of complex characteristics. The interaction of the mechanical and thermal fields is taken into account. To solve the problem, the variational and Bubnov–Galerkin methods are used. The effect of the temperature of dissipative heating on the effectiveness of the active damping of resonant vibration is studied     

Dynamic characteristics of a cantilever beam with partial self-sensing active constrained layer damping treatment

The equations of motion governing the vibration of a cantilever beam with partially treated self-sensing active constrained layer damping treatment(SACLD) are derived by application of the extended Hamilton principle. The assumed-modes method and closed loop velocity feedback control law are used to analyze and control the flexural vibration of the beam. The influence of the bonding layer and piezoelectric layer thickness, material properties, placements of the piezoelectric patch and feedback control parameters on the actuation ability of the vibration suppression are investigated. Some design considerations for pure passive, pure active control, and self-sensing active constrained layer damping are discussed. The present work is supported by the National Natural Science Foundation of China (No. 59635140).     

Two Kinds Equal Frequency Circuits to Achieve Locally Resonant Band Gap of a Circular Plate Attached Alternately by Piezoelectric Unimorphs

A circular thin plate is proposed for vibration attenuation,which is attached alternately by annular piezoelectric unimorphs with resonant shunt circuits.Two kinds of equal frequency resonant shunt circuits are designed to achieve an integrated locally resonant(LR)band gap(BG) with a much smaller transmission factor:(1) the structure is arrayed periodically while the resonant shunt circuits are aperiodic;(2) the resonant shunt circuits are periodic while the structure is aperiodic.The transmission factor curve is calculated,which is validated by the finite element method.Dependences of the LR BG performance upon the geometric and electric parameters are also analyzed.     

Multimode vibration control using several piezoelectric transducers shunted with a multiterminal network

In this paper a new approach is presented to reduce vibrations for one- and two-dimensional mechanical structures, as beam or thin plates, by means of several piezoelectric transducers shunted with a proper electric network system. The governing equations of the whole system are coupled to each other through the direct and converse piezoelectric effect. More in detail, the mechanical equations are expressed in accordance with the modal theory considering n vibration modes and the electrical equations reduce to the one-dimensional charge equation of electrostatics for each of n considered piezoelectric transducers. In this electromechanical system, a shunting electric device forms an electric subsystem working as multi degrees of freedom (dof’s) damped vibration absorber for the mechanical subsystem. Herein, it is introduced a proper transformation of the electric coordinates in order to approximate the governing equations for the whole shunted system with n uncoupled, single mode piezoelectric shunting systems that can be readily damped by the methods reported in literature. A further numerical optimisation problem on the spatial distribution of the piezoelectric elements allows to achieve a better performance. Numerical case studies of two relevant systems, a double clamped beam and a fully clamped plate, allow to take into account issues relative to the proposed approach. Laboratory experiments carried out in real time on a beam clamped at both ends consent to validate the proposed technique.     

The jump phenomenon effect on the sound absorption of a nonlinear panel absorber and sound transmission loss of a nonlinear panel backed by a cavity

Theoretical analysis of the nonlinear vibration effects on the sound absorption of a panel absorber and sound transmission loss of a panel backed by a rectangular cavity is herein presented. The harmonic balance method is employed to derive a structural acoustic formulation from two-coupled partial differential equations representing the nonlinear structural forced vibration and induced acoustic pressure; one is the well-known von Karman??s plate equation and the other is the homogeneous wave equation. This method has been used in a previous study of nonlinear structural vibration, in which its results agreed well with the elliptic solution. To date, very few classical solutions for this nonlinear structural-acoustic problem have been developed, although there are many for nonlinear plate or linear structural-acoustic problems. Thus, for verification purposes, an approach based on the numerical integration method is also developed to solve the nonlinear structural-acoustic problem. The solutions obtained with the two methods agree well with each other. In the parametric study, the panel displacement amplitude converges with increases in the number of harmonic terms and acoustic and structural modes. The effects of excitation level, cavity depth, boundary condition, and damping factor are also examined. The main findings include the following: (1)?the well-known ??jump phenomenon?? in nonlinear vibration is seen in the sound absorption and transmission loss curves; (2)?the absorption peak and transmission loss dip due to the nonlinear resonance are significantly wider than those in the linear case because of the wider resonant bandwidth; and (3)?nonlinear vibration has the positive effect of widening the absorption bandwidth, but it also degrades the transmission loss at the resonant frequency.     

Active vibration control of thin constrained composite damping plates with double piezoelectric layers

Vibrations and the damping behaviour of thin constrained composite plates with double piezoelectric layers are analytically explored by using Fourier transformation and classical laminated plate theory. Electric potential equations in the double piezoelectric layers are solved with respect to closed and open circuit boundary conditions, an exterior dielectric slab and active control. The natural frequencies and loss factors of the constrained smart composite plates with passive control methods are not notably changed in comparison with those of the constrained composite plates without piezoelectric effects since vibrational energy does not efficiently convert to electrical energy. The loss factors of the composite plates with active constrained damping increase and the natural frequencies have significant variations as the proportional derivative gains increase. Transverse displacement power spectra of the piezoelectric composite plates with active control are compared with those of the piezoelectric composite plates with passive control showing that active control has the best suppression performance of vibrations for the constrained laminated plates with double piezoelectric layers. Radial power spectral density, phase angles and cylindrical-wave power spectral density are calculated. Interesting patterns of wave propagation are explained when plane wave expansion is used to obtain Bessel cylindrical waves.     

Active control of structural acoustic pressure in a rectangular cavity using piezoelectric actuators

Active control of structural acoustic pressure in a rectangular cavity with a flexible beam is simulated numerically. The wave equation of the acoustic pressure and the equation of motion of the beam are approximated via the series expansions, and is then expressed in state space form. The control of structural acoustic pressure and vibration of the beam was implemented by applying the optimal voltage on piezoelectric actuators through an LQR controller. Two cases of different external forces acting on the piezoelectric laminated beam are illustrated. Results demonstrate that such a control system can efficiently reduce the structural acoustic pressure.     

Effects of initial stress on the reflection and transmission waves at the interface between two piezoelectric half spaces

The effects of initial stress on the reflection and transmission waves at the interface between two piezoelectric half spaces are studied in this paper. First, the secular equations in the traverse isotropic piezoelectric half space are derived from the general dynamic equation with initial stress taken into consideration. Then, the interface conditions that displacement, stress, electric potential, and electric displacement are continuous across interface are required to be satisfied by three sets of coupled waves, namely, quasi-longitudinal wave, quasi-transverse wave and the electric–acoustic wave. The algebraic equations resulting from the interface conditions are solved to obtain the amplitude ratio of various waves and furthermore the energy reflection and transmission coefficients of various waves. The numerical results are shown graphically and the effects of initial stress are discussed.     

A new method for measuring damping in flexural vibration of thin fibers

In this paper we describe a new method for measuring damping in flexural vibration of filamentous matter, such as polymeric or metallic fibers. This method enables us to measure the damping characteristics of very thin fibers (down to lateral dimensions of a few micrometers). The fiber sample is clamped at one extremity and excited in the flexural vibration mode of a cantilever beam configuration, using a piezoelectric actuator. While the fiber sample vibrates around a flexural eigenfrequency, structural damping is determined from the measurement of the curve of phase difference between excitation and motion. This technique does not require the amplitude of the fiber motion to be determined. The phase curve is inferred from the periodic disturbance occurring when the fiber acts as a shutter for a light beam. This method can be applied to fibers of arbitrary shape and material. Examples are shown of measurements with polymer and metallic fibers. Flexural damping is evaluated at atmospheric pressure and in vacuum. The technique is validated by a comparison with polypropylene damping measurements from standard dynamic mechanical thermal analysis techniques.     

Application of piezoelectric actuation to regularize the chaotic response of an electrostatically actuated micro-beam

The impetus of this study is to investigate the nonlinear chaotic dynamics of a clamped–clamped micro-beam exposed to simultaneous electrostatic and piezoelectric actuation. The micro-beam is sandwiched with piezoelectric layers throughout its length. The combined DC and AC electrostatic actuation is imposed on the micro-beam through two upper and lower electrodes. The piezoelectric layers are actuated via a DC electric voltage applied in the direction of the height of the piezoelectric layers, which produces an axial force proportional to the applied DC voltage. The governing differential equation of the motion is derived using Hamiltonian principle and discretized to a nonlinear Duffing type ODE using Galerkin method. The governing ODE is numerically integrated to get the response of the system in terms of the governing parameters. The results show that the response of the system is greatly affected by the amounts of DC and AC electrostatic voltages applied to the upper and lower electrodes. The results show that the response of the system can be highly nonlinear and in some regions chaotic. Evaluating the K–S entropy of the system, based on several initial conditions given to the system, the chaotic response is distinguished from the periodic or quasiperiodic ones. The main objective is to passively control the chaotic response by applying an appropriate DC voltage to the piezoelectric layers.     

自感知主被动阻尼悬臂梁动态特性分析

由Ｈａｍｉｌｔｏｎ原理导出了压电层作约束层作约束层的自感知主被动阻尼控制结构的振动控制方程;由自感知电压引入速度负反馈闭环控制,并由假设模态法将位移按模态展开,求解了悬臂梁结构的动态特征;对被动控制、自感知主动控制、自感知主被动控制的控制效果进行了分析比较;分析了粘弹层厚度变化、材料参数变化以及压电层厚度、位置等结构参数变化对控制效果及模态频率的影响;并对自感知主被动阻尼控制结构的特点和设计中应注     

Tuning of a vibration absorber with shunted piezoelectric transducers

In order to reduce structural vibrations in narrow frequency bands, tuned mass absorbers can be an appropriate measure. A quite similar approach which makes use of applied piezoelectric elements, instead of additional oscillating masses, are the well-known resonant shunts, consisting of resistances, inductances, and possibly negative capacitances connected to the piezoelectric element. This paper presents a combined approach, which is based on a conventional tuned mass absorber, but whose characteristics can be strongly influenced by applying shunted piezoceramics. Simulations and experimental analyses are shown to be very effective in predicting the behavior of such electromechanical systems. The vibration level of the absorber can be strongly attenuated by applying different combinations of resistant, resonant, and negative capacitance shunt circuits. The damping characteristics of the absorber can be changed by applying a purely resistive or resonant resistant shunt. Additionally, the tuning frequency of the absorber can be adapted to the excitation frequency, using a negative capacitance shunt circuit, which requires only the energy to supply the electric components.