Studies on the retention behaviour of some thiazolylazo derivatives in reversed phase liquid chromatography

The retention behaviour of thiazolylazo derivatives, 4-(2-thiazolylazo) resorcinol (TAR), 4-(2-thiazolylazo)-orcinol (TAO), 2-(2-thiazolylazo)-4-methylphenol (TAC) and 1-(2-thiazolylazo)-2-naphtol (TAN) was studied by reversed phase liquid chromatography. The optimum conditions for the separation of four thiazolylazo derivatives were examined with respect to column, flow rate, mobile phase composition and pH of mobile phase. These derivatives were separated simultaneously on Symmetry C₈ column using composition of acetonitrile/water (60/40, v/v) as mobile phase. The capacity factor (k′) has been decreased at higher pH than pK_a of solute which may due to the increasing concentration of the ionized species as increase the pH of mobile phase. The dependence of log k′ on the volume faction of water in the binary mobile phase and k′ on the liquid–liquid extraction distribution ratio (D_c) in acetonitrile–water (60/40, v/v)/n-octane extraction system for thiazolylazo derivatives were obtained good linear relationship. The results showed that the retention behaviour of these derivatives was mainly affected by the hydrophobic interaction between thiazolylazo as solute and mobile phase.     

Rm Values, retention times and π values of a series of potentially mutagenic nitroimidazo[2,1-b]thiazoles

The R_m values and retention times of a series of nitroimidazo[2,1-b]thiazoles were obtained by means of thin-layer and high-performance liquid chromatography, respectively. Extrapolated R_m and log k′ values were correlated in a statistically significant way with π values calculated according to the literature.     

Structural and magnetic properties of “one-dimensional” barium vanadium triselenide

BaVSe₃ has been synthesized and its crystal structure determined at 293(2)°K. The structure was solved in the hexagonal space group P6₃/mmc (D⁴_6h), with a = 6.9990(11) and c = 5.8621(13) Å. Scans (2 Θ) of a polycrystalline sample revealed that BaVSe₃ undergoes a transition to an orthorhombic unit cell (b′ 3^1/2 a, a′ a, c′ c) at 303(5)°K. Magnetic susceptibility measurements between 4 and 300°K indicate that BaVSe₃ is paramagnetic down to 41(1)°K, where magnetic ordering occurs, with a magnetic moment in the ordered phase of 0.2 μ_B per vanadium atom. The orthorhombic lattice distortion may be caused by the “freezing in” of “soft” vibrational modes.     

Potentiostatic preparation of poly-1,3-dimethoxybenzene films. Kinetics and bilayer structure

The anodic oxidation of 1,3-dimethoxybenzene (MDMB) on a platinum electrode in non-aqueous tetrabutylammonium perchlorate (TBAP) + acetonitrile solutions begins at 1100 mV. Under polarization at constant potential a polymer film is formed at potentials above than 1700 mV. The empirical kinetics of the formation and growth of this film were investigated using microgravimetry and coulometry. Under all experimental conditions the polymerization rate R_p changes after 10 s of polarization, and this behavior can be described by the empirical equationsR_p = k[MDMB]^0.3[TBAP]^0.4t_pol <10sR′_p = k′[MDMB]^0.9[TBAP]^0.5t_pol 10 s The apparent activation energy is 25 ± 1 kJ mol⁻¹ in both cases. The electrogenerated polymer film has a bilayer structure: a inner compact adherent golden layer, and an outer powdery brown layer.     

Determination of the lipophilicity of quinolinesulfonamides by reversed-phase HPLC and theoretical calculations

Reversed-phase high-performance liquid chromatography analyses were used for the determination of the retention factor (log k) of a set of quinolinesulfonamides. The analyses utilized a mixture of acetonitrile/water as the mobile phase. The log k values were linearly dependent on the concentration of acetonitrile and extrapolated to 100% water and gave the lipophilicity parameter log k_w. The parameter log P_HPLC was determined from log k_w values using the calibration curve obtained for five standards. The log P_HPLC parameters are discussed in terms of structure–lipophilicity relationships. Furthermore, the theoretical lipophilic parameters (log P_calc) for all compounds were calculated using chemical programs (e.g., Advanced Chemistry Development (ACD/ logP), miLogP, AlogP, ClogP, and Pallas). The determined log P_HPLC and calculated log P_calc values were compared by linear regression analysis.     

Isotachophoretic determination of stability constants of Ho and Y complexes with diethylenetriaminepentaacetic acid and 1,4,7,10-tetraazadodecane-N,N′,N″,N-tetraacetic acid

The method of capillary isotachophoresis with conductivity detection was applied for the determination of the physico-chemical characteristics (conditional stability constants log β′) of holmium and yttrium complexes with DTPA (diethylenetriaminepentaacetic acid) and DOTA (1,4,7,10-tetraazadodecane-N,N′,N″,N-tetraacetic acid). The log β′ determination is based on the linear relation between the stability constants of lanthanide–DTPA (lanthanide–DOTA) complexes and the reduction of the zone of the complex owing to the bleeding phenomena (liberating free metal ion). The stability constants calculated using this relationship are comparable with the literary data obtained by other methods for both holmium (log β′_Ho–DTPA=21.9, log β′_Ho–DOTA=24.5) and yttrium complexes (log β′_Y–DTPA=21.2, log β′_Y–DOTA=24.4). Capillary isotachophoresis was applied for the determination of the optimum composition of the reaction mixture (metal:ligand ratio) as well.     

Investigation of the zinc(II) acetylacetonate/benzotriazole reaction system in the presence of bridging N,N′-ligands: Pentanuclear, enneanuclear and polymeric complexes

The reaction of Zn(acac)₂ with btaH (1,2,3-benzotriazole) in dmf yielded the pentanuclear complex [Zn₅(bta)₆(acac)₄(dmf)]·dmf (1·dmf). In the presence of pyrazine, the pentanuclear [Zn₅(bta)₆(acac)₄(dmf)]·3.7dmf (2·3.7dmf) and enneanuclear [Zn₉(bta)₁₂(acac)₆]·6dmf (3·6dmf) complexes were formed, whereas in the presence of 4,4′-bpy the 1D coordination polymer [Zn(acac)₂(4,4′-bpy)]_n (4) was isolated. The molecular structures of 1·dmf and 2·3.7dmf reveal that the [Zn₅] clusters consist of four Zn^II ions which span the corners of a tetrahedron and the fifth resides at its centre. The molecular structure of 3·6dmf reveals that the [Zn₉] clusters consist of two corner sharing tetrahedra and the structure can be described as the addition of two [Zn₅] clusters of 1·dmf and/or 2·3.7dmf followed by the simultaneous abstraction of [Zn(acac)₂] and dmf molecules; this alternative was accomplished by recrystallization of 1·dmf from dmf which yielded 3·6dmf. Each of the μ₃-κN:κN′:κN′′ benzotriazolate ligands in 1·dmf, 2·3.7dmf and 3·6dmf spans an edge of the tetrahedron. The molecular structure of 4 reveals mononuclear [Zn(acac)₂] units bridged via 4,4′-bpy molecules to 1D coordination polymer. Characteristic IR bands of the four complexes are discussed in terms of the coordination modes of the ligands and known structures.     

Liquid Chromatographic Behavior of Nitrogen Compounds

Abstract

Chromatographic behavior of nitrogen compounds differed from others. The column efficiency was poor for the compounds and sometimes solutes were not eluted out from a column. Therefore, the elution volume of alkylamines, anilines, pyridines, pyrazines, quinolines and aminopolyaromatic hydrocarbons was measured on a methacrylate gel and octadecyl bonded silica gels in pH controlled acetonitrile/water mixtures. The solvent effect on the dissociation constant differs from that obtained for aromatic acids. The values in acetonitrile/water mixtures are smaller than those obtained in 100% water. The linear relation between log P and log k′ values is obtained in eluents of pH 7 where the retention of these compounds is maximized. Some hydrophobic fragmental constants are proposed from this result. Prediction of retention time of these compounds from their log P values can be done in the individual groups on octadecyl bonded silica gels in pH controlled acetonitrile/water mixtures.     

Hydrothermal synthesis and structures of two zero-dimensional zinc phosphate polymorphs

Two polymorphs of zero-dimensional zinc phosphate with the formula, ⁰_∞[Zn(2,2′-bipy)(H₂PO₄)₂], have been synthesized employing hydrothermal technique and their structure determined by single crystal X-ray diffraction. Both the structures consists of ZnO₃N₂ distorted trigonal-bipyramidal and PO₂(OH)₂ tetrahedral units linked through their vertices giving rise to a zero-dimensional molecular zinc phosphate. The structures are stabilized by extensive hydrogen bond interactions between zero-dimensional monomers. The structures display subtle differences in their packing created by hydrogen bond interactions. Crystal data: polymorph I, triclinic, space group (No. 2), , , , α=67.32(3)°, β=81.67(3)°, γ=69.29(3)°, , Z=2; polymorph II, triclinic, space group (No. 2), , , , α=97.37(2)°, β=100.54(2)°, γ=100.98(2)°, , Z=2.     

LC and Principal Component Analysis in the Lipophilicity Study of Seven Angiotensin II-AT1 Receptor Antagonists (Sartans)

Seven sartans have been chromatographed with acetonitrile-buffer and methanol–buffer in different proportions as mobile phases. The retention values, log k or R _M were extrapolated to zero organic modifier content to obtain the log k _w or R _MW values. Calibration equations were obtained for standards of known lipophilicity. A simple method employing a gradient procedure of 10–100% acetonitrile or methanol in 60 min and standards of the extreme lipophilicity was also elaborated. Chromatographic log P values were compared to those calculated by use of different software products. Finally, principal component analysis was performed to explore and visualize similarities and differences among the drugs and among the methods.

     

Chromatographic Evaluation of the Lipophilic Properties of Selected Pesticides

Monolinuron, chlortoluron, diuron, isoproturon, linuron, diflubenzuron, dimefuron, teflubenzuron, and lufenuron have been chromatographed on an RP-HPLC column and on RP-HPTLC plates with methanol–water in different volume proportions as mobile phases. The retention values log k, and R_M were extrapolated to zero methanol content. Chromatographic lipophilicities (log k_w, R_Mw, _o(HPLC), and _{o (TLC)}) were compared with measured (log P_exp) partition coefficients and with values (A log Ps, IA log P, C log P, log P_Kowin, and x log P) calculated by use of five different software products. The most significant correlations were found between the chromatographic lipophilicities and C log P values. Satisfactory linear correlation was also obtained between lipophilicity (log k_w, R_Mw) and the valence Gutman index (M).     

Kinetics of the R + HBr RH + Br (CH3CHBr, CHBr2 or CDBr2) equilibrium. Thermochemistry of the CH3CHBr and CHBr2 radicals

The kinetics of the reaction of the CH₃CHBr, CHBr₂ or CDBr₂ radicals, R, with HBr have been investigated in a temperature-controlled tubular reactor coupled to a photoionization mass spectrometer. The CH₃CHBr (or CHBr₂ or CDBr₂) radical was produced homogeneously in the reactor by a pulsed 248 nm exciplex laser photolysis of CH₃CHBr₂ (or CHBr₃ or CDBr₃). The decay of R was monitored as a function of HBr concentration under pseudo-first-order conditions to determine the rate constants as a function of temperature. The reactions were studied separately from 253 to 344 K (CH₃CHBr + HBr) and from 288 to 477 K (CHBr₂ + HBr) and in these temperature ranges the rate constants determined were fitted to an Arrhenius expression (error limits stated are 1σ + Student’s t values, units in cm³ molecule⁻¹ s⁻¹, no error limits for the third reaction): k(CH₃CHBr + HBr) = (1.7 ± 1.2) × 10⁻¹³ exp[+ (5.1 ± 1.9) kJ mol⁻¹/RT], k(CHBr₂ + HBr) = (2.5 ± 1.2) × 10⁻¹³ exp[−(4.04 ± 1.14) kJ mol⁻¹/RT] and k(CDBr₂ + HBr) = 1.6 × 10⁻¹³ exp(−2.1 kJ mol⁻¹/RT). The energy barriers of the reverse reactions were taken from the literature. The enthalpy of formation values of the CH₃CHBr and CHBr₂ radicals and an experimental entropy value at 298 K for the CH₃CHBr radical were obtained using a second-law method. The result for the entropy value for the CH₃CHBr radical is 305 ± 9 J K⁻¹ mol⁻¹. The results for the enthalpy of formation values at 298 K are (in kJ mol⁻¹): 133.4 ± 3.4 (CH₃CHBr) and 199.1 ± 2.7 (CHBr₂), and for α-C–H bond dissociation energies of analogous compounds are (in kJ mol⁻¹): 415.0 ± 2.7 (CH₃CH₂Br) and 412.6 ± 2.7 (CH₂Br₂), respectively.     

Prediction of LC retention of steroids using solvatochromic parameters

Summary The proportion of organic modifier and pH of the hydroorganic mobile phase were optimized to separate a series of nine important steroids by LC. It has been shown that linear plots of logk′ against Reichardt’sE _T ^N parameter for the mobile phase is observed over the whole range of compositions of practical importance. Data from these plots summarize an approach for optimization of resolution from only two retention measurements for each compound. pH is shown to be irrelevant. This behaviour could be extrapolated to other steroids and drastically reduce the number of retention values needed for mobile phase optimization for screening analysis of steroids in doping investigations.     

Micellar liquid chromatography for lipophilicity determination of new biologically active 1,3‐purinodiones

A series of newly synthesized 1,3‐purinodiones with potential anticonvulsant activity, exhibiting affinity to adenosine A₁ and/or A_2A receptors, were subjected to micellar LC (MLC) with SDS as micelle‐forming agent and n‐propanol as organic modifier. Two C18 silica‐based columns were employed in MLC: a particle one and a monolithic. In parallel, those derivatives were also analyzed in RP‐LC on four silica‐based columns and on an immobilized artificial membrane column. The correlations between the relevant logarithms of the retention factors of analytes obtained in MLC, immobilized artificial membrane and RP‐LC systems on the one hand, and the calculated log P (clog P) and log D values (clog D) on the other, were examined. The level of the correlations of retention data from MLC and RP‐LC systems with clog P and clog D obtained is similar but it could be stressed that MLC allows increasing the speed of analysis and using only one mobile phase. Moreover, there is no need of applying an extrapolation procedure in lipophilicity determination. Therefore, the MLC systems, providing chromatographic data in a fast and efficient manner, were demonstrated as promising alternatives to the classical RP‐LC systems to estimate the lipophilicity of drugs and drug candidates.     

The C–HCl2Cu(II) synthon in the structural direction and assembly of supramolecular complexes with the 3,3′-bis(2-benzimidazolyl)-2,2′-dipyridine ligand and its N-substituted derivatives

Three new Cu(II) supramolecular complexes [Cu(L₁)Cl₂]·2DMF (1), [Cu(L₂)Cl₂] (2) and [Cu(L₃)Cl₂]·DMF (3) (L₁ = 3,3′-bis(2-benzimidazolyl)-2,2′-dipyridine, L₂ = 3,3′- bis(N-ethyl-2-benzimidazolyl)-2,2′-dipyridine and L₃ = 3,3′-bis(N-benzyl-2-benzimidazolyl)-2,2′-dipyridine) have been prepared and characterized by elemental analysis, IR spectra and single crystal X-ray diffraction. X-ray structural analysis of L₁, L₂·3.5H₂O and L₃·H₂O indicates that all three ligands adopt the trans conformation with the two benzimidazole fragments located on opposite sides of the dipyridyl backbone. While in complexes 1–3, all the ligands display the cis conformation and behave as bidentate chelating reagents to coordinate with Cu(II). The inorganic chloride ions always act as a reliable hydrogen bonded acceptor in these structures, and the resulting C–HCl₂Cu supramolecular synthons play a significant role in the formation and stabilization of the structures. Moreover, additional non-covalent interactions, such as C–Hπ, are also identified to extend the discrete (0-D) or low-dimensional (1-D) motifs into high-dimensional architectures.     

Separation of fluorescent 1,N6 ethenoderivatives of diadenosine polyphosphates and their enzymatic degradation products by reversed-phase high-performance liquid chromatography

Summary The retention, selectivity and elution order of fluorescent 1,N⁶-etheno derivatives of diadenosine polyphosphates and their enzymatic degradation products on octadecyl and phenyl-bonded silica columns have been studied as a function of mobile phase pH, ionic strength and organic modifier content. Good separations of the compounds of interest were achieved using mobile phases of around 0.1M potassium phosphate buffers at neutral pH containing approximately 10% methanol or 4% acetonitrile for C₁₈ columns and 5% methanol or 1.5% acetonitrile for phenyl columns. The data obtained were used to establish isocratic assays for diadenosine polyphosphate cleaving activities from chromaffin cells using Di(1,N⁶-ethenoadenosine) polyphosphates as fluorogenic substrate analogues followed by fluorescence detection.     

Determination of lipophilicity for antitumor acridinone derivatives supported by gradient high-performance liquid chromatography method

The lipophilicity values of selected acridinone (imidazoacridinone and triazoloacridinone) derivatives were measured by gradient reversed-phase high-performance liquid chromatography (RP-HPLC) using a C18 stationary phase with a water/acetonitrile mixture as a mobile phase. The retention times obtained served as input data and appropriate log k_w values (i.e., the retention factor log k_w extrapolated to 0% organic modifier) as an alternative to log P were calculated using the DryLab program. The relationships between the lipophilicity (log k_w) and the chemical structure of the studied compounds, as well as correlation between experimentally determined lipophilicities (log k_w) and log P data calculated using some commonly available software, are discussed.     

Correlation between hydrophobicity of amino acids and retention data in reversed-phase liquid chromatography with micellar eluents

Summary Hydrophobic character is usually expressed in terms of the partition coefficient in 1-octanol-water (log P_o/w). However, measurement of this coefficient is often problematic. Retention in micellar liquid chromatography is mainly due to hydrophobic interactions and can also be used as an index of hydrophobicity. A hydrophobicity scale was established with retention data foro-phthalaldehyde (OPA)-N-acetyl-L-cysteine (NAC) amino acid derivatives, using the glycine derivative as reference. Since the OPA-NAC derivatives only differ in the nature of R₁ in the amino acid (R₁CH (COOH)NH₂), in the absence of electrostatic interactions the hydrophobic character of the substituent was responsible for retention. Linear relationships were obtained between log of the ratiok′ of amino acid derivatives:k′ of the glycine derivative for a given mobile phase, and logP _o/w for the R₁ substituent. Good correlations were also found for phenylthiohydantoin amino acid derivatives.