Calorimetric study of blends of poly(butylene terephthalate) and a liquid crystalline polyester

The thermal properties of solution-prepared blends of poly(butylene terephthalate) (PBT) and liquid crystalline poly(biphenyl-4,4′-ylene sebacate) (PB8) have been studied by differential scanning calorimetry (DSC). The smectic-to-isotropic (s → i) transition of the mesomorphic component is observed at temperatures slightly increasing with the PB8 content, in the 270–280°C range; on cooling, the mesophase formation (i → s transition) takes place at temperatures that decrease markedly with decreasing PB8 content. The temperatures of the crystal-to-smectic and smectic-to-crystal transitions of PB8 are almost invariant with blend composition. The melting and crystallization temperatures of the PBT phase decrease on increasing the content of the liquid crystalline component. These results, together with those of isothermal calorimetry of both the crystallization of the PBT component and the mesophase formation of the PB8 component of the blends, indicate that the two polymers are not immiscible in the isotropic state. In this latter state, however, the two polyesters undergo transesterification, which can be followed through changes in the DSC scans. The effect of the thermal history on the properties of the blends has been studied with particular attention. Both the dynamic and the isothermal calorimetric measurements provide evidence of an increase of the degree of crystallinity of PBT on addition of the liquid crystalline component up to about 35–50% by weight.     

Miscibility and transesterification in blends of liquid crystalline copolyesters and polyarylate

Blends of poly(oxybenzoate-p-ethylene terephthalate) (POB-PET) and polyarylate were confirmed to be a partially miscible system by differential scanning calorimetry. When 60/40 POB-PET/PAr blend was annealed at high temperature (above 270°C) for several minutes, the ester–ester interchange (transesterification) in the blend took place immediately, as evidenced by Fourier Transformed infrared analyses. The analysis of the blend annealed at 290°C by ¹H-¹³C nuclear magnetic resonance disclosed that there were four new diads appearing in 15 min and an additional one produced in 60 min during the heat treatment. The miscibility between POB-PET and polyarylate increased with the mol concentration of these new diads judging from differential scanning calorimetry. The evolution of the concentration of the diad ethylene glycol-isophthalate during the annealing can be described by a second-order reaction. The activation energy of forming the diad ethylene glycol-isophthalate was 26.5 kcal/mol, and the preexponential factor for the transesterification reaction is 3.7 × 10⁸ min⁻¹. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1959–1969, 1998     

Influences of a liquid crystalline polymer,vectra A950, on crystallization kinetics and thermal stability of poly(trimethylene terephthalate)

The non-isothermal crystallization behavior of poly(trimethylene terephthalate) (PTT) and its blends with a liquid crystalline polymer, namely Vectra A950 (VA), was studied by differential scanning calorimetry. The values of the half-time of crystallization, t _0.5 and the parameter F(T) in the combined Avrami and Ozawa equation indicated that VA can enhance the PTT crystallization rate by acting as a nucleating agent. The crystallization activation energy of the PTT phase increased with increasing VA content. The blends were immiscible, as can be inferred from their morphology. Thermogravimetric analysis of the blends revealed improved thermal stability by the incorporation of VA.     

Melt-crystallization behavior and isothermal crystallization kinetics of crystalline/crystalline blends of poly(ethylene terephthalate)/poly(trimethylene terephthalate)

The melt-crystallization and isothermal melt-crystallization kinetics of poly(ethylene terephthalate)/poly(trimethylene terephthalate) blends (PET/PTT) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy. Although PET and PTT in the binary blends are miscible at amorphous state, they will crystallize individually when cooled from the melt. In the DSC measurements, PET component with higher supercooling degree will crystallize first, and then the crystallite of PET will be the nucleating agent for PTT, which induce the crystallization of PTT at higher temperature. On the other hand, in both blends of PET80/PTT20 and PET60/PTT40, the PET component will crystallize at higher temperature with faster crystallization rate due to the dilute effect of PTT. So the commingled minor addition of one component to another helps to improve the crystallization of the blends. For blends of PET20/PTT80 and PET40/PTT60, isothermal crystallization kinetics evaluated in terms of the Avrami equation suggest different crystallization mechanisms occurred. The more PET content in blends, the fast crystallization rate is. The Avrami exponent, n = 3, suggests a three-dimensional growth of the crystals in both blends, which is further demonstrated by the spherulites formed in all blends. The crystalline blends show multiple-melting peaks during heating process.     

Crystallization and melting behavior of liquid crystalline copolyesters based on poly(ethylene terephthalate)

A series of copolyesters were prepared by the incorporation of p‐hydroxybenzoic acid (HBA), hydroquinone (HQ), and terephthalic acid (TA) into poly(ethylene terephthalate) (PET). On the basis of viscosity measurements, high molar mass copolyesters were obtained in the syntheses, and ¹H‐NMR analyses indicated the total insertion of comonomers. They exhibit nematic phase above melting temperature, as observed by polarized light microscope (PLM). Their crystallization and melting behaviors were also studied by differential scanning calorimetry (DSC) and wide angle X‐ray diffraction (WAXD). It was found that these copolyesters are more crystalline than copolyesters prepared from PET and HBA. Introduction of HQ/TA disrupts longer rigid‐rod sequences formed by HBA, and thus enhances molecular motion and increases crystallization rate and crystallinity. Isothermal crystallization at solid phase polymerization conditions (up to 24 h at 200°C) resulted in increased copolymer randomness (by NMR) and higher melting point, the latter attributed to structural annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 369–377, 1999     

Transesterification kinetics in the reactive blends of liquid crystalline copolyesters and poly(ethylene terephthalate)

The transesterification kinetics of poly(ethylene terephthalate) (PET)/copoly(oxybenzoate-p-terephthalate) (liquid crystalline polymer, LCP) (70/30 by weight) in the presence of small amount of bis(2-oxazoline) (BOZ) as chain extender was studied by using 1H nuclear magnetic resonance. The kinetic data was treated as a second-order reversible reaction, and it was found that the rate constants of transesterification at 270, 280 and 290 °C were 1.55×10⁻², 2.20×10⁻² and 3.01×10⁻² min⁻¹, respectively, the value of which was higher than the blend without addition of BOZ, 1.26×10⁻² min⁻¹, and the activation energy of PET/LCP transesterification was 84.4 kJ mol⁻¹.     

Biodegradable liquid crystalline aromatic/aliphatic copolyesters. Part I: Synthesis, characterization, and hydrolytic degradation of poly(butylene succinate-co-butylene terephthaloyldioxy dibenzoates)

To increase the thermal and mechanical properties of the aliphatic polyester poly(butylene succinate) (PBS), a series of potentially biodegradable liquid crystalline aromatic/aliphatic random copolyesters were prepared by melt polycondensation of new mesogenic monomers dimethyl 4,4′-(terephthaloyldioxy) dibenzoate (MTB), dimethyl succinate, and 1,4-butanediol. The synthesized copolyesters were characterized by means of proton nuclear magnetic resonance spectroscopy (¹H NMR), gel permeation chromatography (GPC), viscosity measurements, differential scanning calorimetry (DSC), thermogravimetry (TG), X-ray diffraction (XRD), polarizing light microscopy (PLM) and mechanical property measurements. The MTB content was varied so that the effects of the mesogen content on the thermal and mechanical properties, degradable behaviours and mesophase were examined. It was found that introducing the rigid rod mesogens could increase the thermal stability and the mechanical properties, while it reduced the melting temperature (T_m), the crystallization temperature (T_c), the degree of relative crystallinity (X_c) and the hydrolytic degradation rate. Only the homopolyester poly(butylenes terephthaloyldioxy dibenzoates) was able to show the schlieren texture characteristic of nematics.     

Phase behavior and interactions in blends of poly[(butylene adipate)-co-poly(butylene terephthalate)] copolyester with poly(4-vinyl phenol)

Miscibility with a linear T _g–composition relationship was proven for blend of poly(butylene adipate-co-butylene terephthalate) [P(BA-co-BT)] with poly(4-vinyl phenol) (PVPh). In comparison to the blends of PBA/PVPh and poly(butylene terephthalate) (PBT)/PVPh, the Kwei’s T _g model fitting on data for the P(BA-co-BT)/PVPh blend yields a q value between those for the PBA/PVPh and PBT/PVPh blends. The q values suggest that the interaction strength in the P(BA-co-BT)/PVPh blend is not as strong as that in the PBT/PVPh blend. Upon mixing the PVPh into the immiscible blend of PBA and PBT, the ternary PBA/PBT/PVPh blends only exhibits partial miscibility. Full-scale ternary miscibility in whole compositions is not possible owing to the significant ∆χ effect (χ _ij  – χ _ik ). The wavenumber shifts of the hydroxyl IR absorbance band indicates that the H-bonding strength is in decreasing order—PBT/PVPh > P(BA-co-BT)/PVPh > PBA/PVPh—and shows that the BA segment in the copolymer tends to defray interactions between P(BA-co-BT) and PVPh in blends.     

The annealing and thermal analysis of poly(butylene terephthalate)

When poly(butylene terephthalate) (PBT) is annealed, a second endotherm is often displayed in a subsequent scanning thermal analysis at a temperature below that of the original endotherm, and this new endotherm appears to grow with annealing at the expense of the original. This growth is not due to chemical changes, because the thermogram obtained before annealing is recovered after complete melting. But a physical change would also seem unlikely because the transformation of higher-melting into lower-melting crystals is generally prohibited by thermodynamics. Two hypotheses to explain the result were tested. The first is that higher-melting crystals are not transformed into lower-melting crystals. Instead, because of recrystallization during thermal analysis, the single endotherm that results without annealing overestimates the population of high-melting crystals present before the analysis. This hypothesis was tested by extending to annealing a mathematical analysis previously used to describe the thermal scanning behavior of specimens crystallized at different cooling rates. Though most features of the thermograms obtained after annealing were able to be described, the decrease in the higher-temperature endotherm concomitant with growth of the lower endotherm was not. The second hypothesis is that the transformation of higher-melting to lower-melting crystals during annealing is allowed because it is coupled to the crystallization of formerly amorphous material. The amount of such crystallization observed for PBT was found to be sufficient to satisfy thermodynamic requirements, suggesting that this hypothesis is correct. © 1994 John Wiley & Sons, Inc.     

Blends of a thermotropic liquid‐crystalline polymer and a poly(butylene terephthalate)/organoclay nanocomposite

Blends were synthesized via the melt blending of a thermotropic liquid‐crystalline polymer (TLCP) and a poly(butylene terephthalate) (PBT) hybrid containing 2 wt % organoclay. A TLCP was also synthesized with side groups based on a nematic liquid‐crystalline phase. The blends of TLCPs with PBT hybrids were melt‐spun with different concentrations of the liquid‐crystalline polymer and different draw ratios (DRs) to produce monofilaments. Regardless of the TLCP concentration in the hybrids, transmission electron microscopy photographs proved that the clay layers of the organoclay were intercalated and partially exfoliated in the PBT matrix. At DR = 1, the maximum enhancement in the ultimate tensile strength was observed for blends containing 8% TLCP, and the tensile strength decreased with further increases in the TLCP concentration. The initial modulus monotonically increased with increasing TLCP concentration. When DR increased from 1 to 44, the increased stretching caused the tensile property to decrease significantly, debonding to occur, and voids to form. These trends with increasing DR were observed in all the systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3667–3676, 2004     

Isothermal crystallization kinetics of poly(ethylene terephthalate) in blends with a liquid crystalline polyester (Vectra A)

The isothermal crystallization kinetics of poly(ethylene terephthalate) (PET) in blends with a fully aromatic liquid crystalline copolyester (Vectra A) were studied with differential scanning calorimetry. PET crystallization rates decreases with increasing Vectra fractions in the blends, and the percentage of PET that is crystalline also decreases with increasing Vectra. The equilibrium PET melting temperature for blends containing 40% or more Vectra is unambiguously below that of pure PET. Attenuated total reflectance Fourier-transform infrared spectroscopy measurements indicate that PET/Vectra transesterification does not take place. The results are consistent with a scenario based on prior NMR data in which there is some interphase mixing between the liquid crystalline and flexible polymers and an increase in the fraction of gauche conformers in the PET.     

Stepwise annealing of poly(butylene terephthalate)

Annealing of poly(butylene terephthalate) (PBT) was studied by differential scanning calorimetry (DSC) and small angle X‐ray scattering (SAXS) measurement. A PBT sample was annealed at a recrystallization temperature where recrystallization occurs with a maximum rate in the heating process of the sample. In the subsequent annealing steps, the annealed sample was annealed repeatedly at the recrystallization temperatures, and the stepwise annealing sample was obtained. Peak melting temperature (T_m) and sharpness of DSC peak of the stepwise annealing sample increased with the annealing step. A high melting‐temperature sample was obtained in a short time, and T_m increased up to 238.5°C which is higher than all the T_m values that appear in the literature. The long period calculated from SAXS curves of the stepwise annealing sample increased with the annealing step. The increase of crystallite size and perfection of the crystal in the stepwise annealing process is suggested. Annealing experiment indicated that T^°_m should be higher than about 235°C. T_m increased linearly with the annealing temperature of the final step in the stepwise annealing (T_a). The equilibrium melting temperature (T^°_m) for PBT was estimated to be 247°C by the application of a Hoffman–Weeks plot to the relation between T_m vs. T_a. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2420–2429, 1999     

Thermal transition of a wholly aromatic thermotropic liquid crystalline copolyester

A copolyester was prepared from p-hydroxybenzoic acid (HBA), 2,6-naphthalene dicaboxylic acid (NDA), and hydroquinone (HQ). Thermal transition behavior and the crystal structure of this copolyester were investigated by using polarized light microscopy (PLM), differential scanning calorimetry (DSC), and wide-angle X-ray diffraction (WAXD) after annealing at solid-phase polymerization conditions. A glass transition or newly ordered structure in the 270–290°C range was observed on annealing at 260°C, which increased with annealing time, attributed to mobility and reactive rearrangement in amorphous regions. Broad and unclear WAXD profiles and multimelting behaviors were found on annealing at 280°C, and explained by hexagonal and orthorhombic lattice formation and transformation. A large increase in melting temperature was observed only on annealing at a temperature (320°C) near the crystal–nematic transition, suggesting annealing temperatures near the melting point are required for sufficient mobility to afford crystalline rearrangement via transesterification. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3763–3769, 1999     

Nonisothermal crystallization kinetics of poly (phenylene sulphide) in composites with a liquid crystalline polymer

The article deals with the melting and nonisothermal crystallization behavior of neat poly (phenylene sulphide) (PPS) and its composites with a thermotropic liquid crystalline polymer (TLCP)—Vectra A950, prepared by melt mixing and probed by differential scanning calorimetry. The various macrokinetic models namely, the Ozawa, the modified Avrami, the Tobin, and the Mo models were applied to describe the crystallization kinetics under nonisothermal conditions. The kinetic crystallizabilty of PPS/TLCP composites calculated using the approach of Ziabicki varies depending on these two composite composition‐induced effects. Similarly Mo model predicts that to obtain a higher degree of crystallizabilty for PPS/TLCP composites, a higher cooling rate should be used. The effective energy barrier based on the differential isoconversional method of Friedman is found to be an increasing function of relative degree of melt conversion. The effect is explained in terms of nucleation theory proposed by Wunderlich to crystallization of polymers. The Lauritzen–Hoffman parameters are estimated using G = 1/t_0.5 effective activation energy equation proposed by Vyazovkin and Sbirrazzuoli. The K_g values estimated from latter equations are more comparable with values obtained using isothermal crystallization data than 1/t_0.5 method. Furthermore, the kinetic analysis using this equation shows a regime transition from regime II to regime III for 100/00, 90/10, 80/20 PPS/TLCP composites, basically attributed to reduced mobility of PPS chains in composites. This regime II to III transition is accompanied by a morphological transition from defective spherulitic sheaf‐like structures to ordered sheaf‐like structures. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1070–1100, 2010     

Heat capacity of poly(butylene terephthalate)

The low‐temperature heat capacity of poly(butylene terephthalate) (PBT) was measured from 5 to 330 K. The experimental heat capacity of solid PBT, below the glass transition, was linked to its approximate group and skeletal vibrational spectrum. The 21 skeletal vibrations were estimated with a general Tarasov equation with the parameters Θ₁ = 530 K and Θ₂ = Θ₃ = 55 K. The calculated and experimental heat capacities of solid PBT agreed within better than ±3% between 5 and 200 K. The newly calculated vibrational heat capacity of the solid from this study and the liquid heat capacity from the ATHAS Data Bank were applied as reference values for a quantitative thermal analysis of the apparent heat capacity of semicrystalline PBT between the glass and melting transitions as obtained by differential scanning calorimetry. From these results, the integral thermodynamic functions (enthalpy, entropy, and Gibbs function) of crystalline and amorphous PBT were calculated. Finally, the changes in the crystallinity with the temperature were analyzed. With the crystallinity, a baseline was constructed that separated the thermodynamic heat capacity from cold crystallization, reorganization, annealing, and melting effects contained in the apparent heat capacity. For semicrystalline PBT samples, the mobile‐amorphous and rigid‐amorphous fractions were estimated to complete the thermal analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4401–4411, 2004     

An evoluted bio-based 2,5-furandicarboxylate copolyester fiber from poly(ethylene terephthalate)

A series of bio-based poly(ethylene terephthalate-co-ethylene 2,5-furandicarboxylate) (PEFT) fibers was prepared via the industrially feasible melt-spinning and hot-drawing process. The effect of 2,5-furandicarboxylic acid (FDCA) content on the fibers properties was studied using differential scanning calorimetry, wide-angle X-ray diffraction, sound velocity, tensile, and boiling water shrinkage tests. It was found that the PEFT fibers showed comparable or superior tenacity to the PET fibers under the same conditions, especially the PEFT-4 fibers exhibited the highest tenacity (2.3, 2.9 cN/dtex for the drawn PET and PEFT-4 fibers prepared at the same take-up speed of 2500 m/min and a fixed draw ratio of 1.6). Moreover, the boiling water shrinkage of the PEFT fibers was quite close to that of the PET fibers under the same conditions, showing that the PEFT fibers were comparable to the PET fibers in heat resistance. The results indicated that the bio-based PEFT fibers would be a feasible alternative for the PET fibers, in terms of sustainability, processability, and mechanical properties. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 320–329     

Synthesis and liquid crystalline properties of new amide‐modified poly(1,4‐cyclohexanedimethylene terephthalate)

New series of cycloaliphatic poly(ester‐amide)s, poly(1,4‐cyclohexanedimethyleneterephthalate‐co‐1,3‐cyclohexanedimethylene terephthalamide), were synthesized through solution polymerization route. The compositions of ester/amide units in the copolymers were varied from 0 to 100% by varying the amount of 1,4‐cyclohexanedimethanol and 1,3‐cyclohexanebis(methylamine) in the feed. The structures of the polymers were confirmed by NMR and FTIR, and the molecular weights were determined by inherent viscosity. The composition analysis by NMR reveals that the reactivity of the diamine toward the acid chlorides is lowered than that of diol, which results in the formation of more ester content in the poly (ester‐amides). The thermal analysis indicate that the new poly(ester‐amide)s having less than 10 mol % of amide linkages are thermotropic liquid crystalline from 200 to 250 °C and a thread like nematic phases are observed under the polarizing microscope. WXRD studies suggest that the liquid crystalline domains promote the nucleation process in the polyester chains and increases the percent crystallinity of the poly(ester‐amide)s. The glass transition temperature of the copolymers initially increases with increase in amide units because of the presence of nematic phases and subsequently follows the Flory–Fox behavior. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 42–52, 2006     

NMR study of ester-interchange reactions during melt mixing of poly(ethylene terephthalate)/poly(butylene terephthalate) blends

The occurrence of ester-interchange reactions during PET/PBT blend processing has been confirmed by ¹³C-NMR measurements. The limitations of the method for precise quantification of the extent of reaction between high molecular weight polyester blends have also been pointed out. Titanium alkoxide has been confirmed as an efficient catalyst, and, within experimental precision, the stabilizing effect of triphenyl phosphite addition has been demonstrated. © 1996 John Wiley & Sons, Inc.