Comparative investigation of long-wave infrared generation based on ZnGeP2 and CdSe optical parametric oscillators

Long-wave infrared (IR) generation based on type-II (o→e+o) phase matching ZnGeP₂ (ZGP) and CdSe optical parametric oscillators (OPOs) pumped by a 2.05 μm Tm,Ho:GdVO₄ laser is reported. The comparisons of the birefringent walk-off effect and the oscillation threshold between ZGP and CdSe OPOs are performed theoretically and experimentally. For the ZGP OPO, up to 419 mW output at 8.04 μm is obtained at the 8 kHz pump pulse repetition frequency (PRF) with a slope efficiency of 7.6%. This ZGP OPO can be continuously tuned from 7.8 to 8.5 μm. For the CdSe OPO, we demonstrate a 64 mW output at 8.9 μm with a single crystal 28 mm in length.     

Comparative investigation of long-wave infrared generation based on ZnGeP2 and CdSe optical parametric oscillators

Long-wave infrared(IR) generation based on type-II(o→e+o) phase matching ZnGeP 2(ZGP) and CdSe optical parametric oscillators(OPOs) pumped by a 2.05 μm Tm,Ho:GdVO 4 laser is reported.The comparisons of the birefringent walk-off effect and the oscillation threshold between ZGP and CdSe OPOs are performed theoretically and experimentally.For the ZGP OPO,up to 419 mW output at 8.04 μm is obtained at the 8 kHz pump pulse repetition frequency(PRF) with a slope efficiency of 7.6%.This ZGP OPO can be continuously tuned from 7.8 to 8.5 μm.For the CdSe OPO,we demonstrate a 64 mW output at 8.9 μm with a single crystal 28 mm in length.     

Broadly tunable noncritically phase-matched ZnGeP2 optical parametric oscillator with a 2-microJ pump threshold

We report a high-repetition-rate (1-10-kHz) optical parametric oscillator (OPO) based on noncritically phase-matched ZnGeP2 (ZGP). The pump source was an OPO based on periodically pole lithium niobate that was pumped in turn by a Q-switched diode-pumped 1-microm Nd:YAG laser. The ZGP OPO yielded continuously tunable output from 3.7 to 10.2 microm by tuning of the pump wavelength from 2.3 to 3.7 microm. At the optimal pump focusing, the minimum ZGP OPO threshold achieved was 2 microJ, which is to our knowledge the lowest ever reported for a singly resonant OPO. The output energy in the 6-8-microm range was > 20 microJ, and the quantum efficiency of converting 1-microm radiation to the mid IR exceeded 10%.     

Performance evaluation of ZnGeP2 optical parametric oscillator pumped by a Q-switched Tm,Ho:GdVO4 laser

A doubly resonant ZnGeP2 （ZGP） optical parametric oscillator （OPO） pumped by a novel Tm,Ho：GdVO4 laser was demonstrated. Cryogenic Tin（5 at.-%）, Ho（0.5 at.-%）：GdVO4 laser with high pulse repetition frequency （PRF） of 10 kHz at 2.05 μm was employed as pumping source of ZGP OPO. The 15-mm-long ZGP crystal, 55° cut for I-type phase-matching with low absorption coefficient less than 0.05 cm^-1 at 2 μm, was placed in a piano-piano cavity with resonator length of 30 mm. The ZGP OPO generated a total combined output power of 1.2 W at 3.75 and 4.52 μm under pumping power of 5.3 W, corresponding to slope efficiency of 40% from incident 2μm laser power to midinfrared （Mid-IR） output. A widely tunable range from 3.0 to 6.5 μm was achieved by changing the crystal angle only 3.5°.     

Mid-infrared optical parametric oscillator based on ZnGeP2 pumped by 2-μm laser

We present a 3 5 μ m optical parametric oscillator (OPO) based on ZGP pumped by KTP OPO 2.1-μ m laser. The tuning curves of ZGP OPO are calculated. The 8 ×6 ×18 (mm) ZGP crystal, whose end faces are antireflection coated at 2.1 and 3.7 4.6 μ m, is cut as θ =53.5°, φ =0°. When the pump power of 2.1-μ m polarized laser is 15 W at 8 kHz, 5.7-W output power and 46.6% slope efficiency are obtained with a ZGP type I phase match. Central wavelengths of the signal and idler lasers are 4.10 and 4.32 μ m, respectively. Pulse duration is about 27 ns. Beam quality factor M 2 is better than 1.8. The tunability of 3 5 μ m can be achieved by changing the angle of the ZGP crystal.     

磷锗锌光学参量振荡器技术研究

 报道了一台高重复频率2 mm光学参量振荡器泵浦的磷锗锌光学参量振荡器。磷锗锌晶体(ZnGeP₂,简称ZGP)采用Ⅰ类相位匹配方式,切割角度q为55°,f为0°,尺寸5.5 mm×6 mm×18 mm,在4.0 kHz重复频率下,当注入5.2 W的2 mm圆偏振光时,获得310 mW中红外输出,p偏振态2 mm到3～5 mm光-光转换效率12%。通过调节晶体的角度,实验获得ZGP光学参量振荡器的波长调谐曲线,在误差范围内与理论变化规律相符。     

Pump tuned wide tunable noncritically phase-matched ZnGeP2 narrow line width optical parametric oscillator

A line tunable singly resonant noncritically phase matched narrow band width ZnGeP₂ (ZGP) optical parametric oscillator pumped by the output idler radiation from a KTA OPO based on a 20 mm long KTA crystal pumped from a Q-switched Gaussian shaped Nd:YAG laser beam with a grating having grooves density 85 lines/mm has been demonstrated in the spectral ranges of 3–7 μm. The measured threshold of oscillation energy was 10 μJ. The conversion efficiency was 20.5% and slope efficiency of the ZGP OPO was 20% using a 23 mm long ZGP crystal at 26 mm cavity length. Line width of the generated infrared radiation from ZGP OPO was 37–60 nm.     

A ring ZnGeP2 optical parametric oscillator pumped by a Ho:LuAG laser

We have demonstrated that we believe to be the first ring ZnGeP₂ (ZGP) optical parametric oscillator (OPO) pumped by a pulsed Ho:LuAG laser. The maximum output power of the ring ZGP OPO laser was 5.51 W at 13.1 W incident Ho pump power, corresponding to a slope efficiency of 59.0 %. The ZGP OPO laser produced 14 ns mid-infrared pulses in the 3.72–4.01 and 4.37–4.75 μm spectral regions simultaneously. In addition, the continuous wave Ho:LuAG laser generated 26.5 W of linearly output at 2,094.4 nm at the absorbed Tm pump power of 49.9 W.     

High-power,high-quality ZGP OPO pumped by a Tm,Ho:GdVO<Subscript>4</Subscript> laser

We report a ZGP OPO system capable of producing >6 W at a signal wavelength of 3.80 μm and an idler wavelength of 4.45 μm. The pumping source is the Tm,Ho:GdVO₄ laser operated at 2.049 μm with an M ² of 1.07. The ZGP OPO generated a total combined output power of 6.1 W at signal wavelength and idler wavelength under pumping power of 18.3 W, and an M ² of 1.7 for OPO output was obtained.     

1.2 W中红外ZnGeP2光参量振荡器

报导了利用Tm,HoGdVO4激光器抽运双谐振ZnGeP2光参量振荡器实验研究.Tm(5%),Ho(0.5%)GdVO4晶体采用液氮制冷方式,工作在77 K温度条件下.以25 W波长为800 nm的光纤耦合激光二极管抽运,2 μm激光最大平均功率7 W,脉冲宽度小于30 ns, 脉冲重复频率5 kHz到20 kHz可调.非线性频率转换晶体ZnGeP2长15 mm,55?切割,OPO谐振腔为平平腔,腔长约25 mm.在5W的2 μm激光抽运下,脉冲重复频率10 kHz,实现了信号光3.7 μm及闲频光4.5 μm中红外激光输出,参量光脉冲宽度为15～17 ns,最大平均功率大于1.2 W,光-光转换效率为20%.测量参量光输出光束全宽度远场发散角4 mrad,光束质量M2因子小于3.     

Mid-infrared ZGP OPO pumped by near-degenerate narrowband type-I PPKTP parametric oscillator

The total pulse energy of the signal and idler in a near-degenerate type-I periodically poled KTiOPO₄ (PPKTP) optical parametrical oscillator (OPO) was spectrally confined within a 2 nm spectral bandwidth at 2.13 μm. This was achieved by using a volume Bragg grating as the output coupler. Both the signal and the idler from the PPKTP OPO were then simultaneously used to pump a mid-infrared ZnGeP₂ (ZGP) OPO. The 2 nm bandwidth was narrower than the ZGP crystal acceptance bandwidth and, thus, made efficient conversion in the second OPO possible. A total slope efficiency of 10% from 1.06 μm to the 3.5–5 μm region was demonstrated, generating 250 μJ in the mid-IR with only 3.6 mJ of 1.06 μm pump energy. This corresponds to a Nd:YAG pump to mid-IR conversion efficiency of 7%. PACS 42.65.Yj; 42.72.Ai; 42.40.Eq     

Tunable 7 12-microm optical parametric oscillator using a Cr,Er:YSGG laser to pump CdSe and ZnGeP(2) crystals

A CdSe optical parametric oscillator (OPO) pumped by a 2.79-mum , Cr, Er:YSGG laser yielded a 59% signal-plus-idler slope efficiency (eta), a total idler output of 1.2-2.4mJ between 8.5 and 12.3 mum , and an idler beam that was 2.2-2.5 times the diffraction limit. A ZnGeP(2) OPO operated with a lower threshold, eta = 29% , and a forward idler output of 0.7-2.4 mJ from 6.9 to 9.9 microm . The signal and idler bandwidths were typically 4 cm(-1) for each OPO.     

Wavelength-agile mid-infrared (5-10 microm) generation using a galvano-controlled KTiOPO4 optical parametric oscillator

A wavelength-agile mid-infrared (IR) ZnGeP2 (ZGP) optical parametric oscillator (OPO) using a galvano-controlled double-crystal KTiOPO4 (KTP) OPO was demonstrated. The mid-IR wavelength was tuned by varying the KTP OPO pump wavelength while the ZGP crystal angle remained fixed. Rapid tuning of the KTP OPO was achieved by changing the crystal angle by using the galvano scanner. Our mid-IR source can jump to a different wavelength without scanning through the intermediate wavelengths while also permitting continuous-wavelength scanning. The mid-IR source can be tuned from approximately 5to10 microm at a phase-matching angle of 51 degrees , while the pump wavelength is controlled in the 1.95-2.2 microm range.     

A High-Power,Long-Wavelength Infrared ZnGeP<Subscript>2</Subscript> Opo Pumped by a <Emphasis Type="Italic">Q</Emphasis>-Switched Tm,Ho:GdVO<Subscript>4</Subscript> Laser

We report a high-power, long-wavelength infrared ZnGeP₂ (ZGP) optical parametric oscillator (OPO) pumped by a Q-switched Tm,Ho:GdVO₄ laser. The wavelength tuning range of 7.8–9.9 μm is realized by rotating the external angle of the ZGP crystal. We obtain an output power over 30 mW across the whole wavelength range and achieve a 1.71 W output power at 8.08 μm by transmitting the OPO parameters, corresponding to an idler laser slope efficiency of 12.1%.     

Mid-infrared ZnGeP2 parametric oscillator directly pumped by a pulsed 2 microm Tm-doped fiber laser

We have demonstrated what we believe to be the first mid-infrared optical parametric oscillator (OPO) pumped directly by a pulsed Tm-doped fiber laser. The Tm-fiber pump laser produces 30 ns pulses with a repetition rate of 30 kHz at a wavelength of 2 microm. The ZnGeP2 (ZGP) OPO produces 20 ns mid-IR pulses in the 3.4-3.9 microm and 4.1-4.7 microm spectral regions simultaneously. More than 658 mW of mid-IR output power has been generated with a total OPO slope efficiency greater than 35%.     

Continuous-wave singly resonant optical parametric oscillator based on periodically poled RbTiOAsO(4)

We report a continuous-wave optical parametric oscillator (OPO) based on periodically poled RbTiOAsO(4) (PPRTA). The singly resonant OPO, which is located within a Ti:sapphire laser, has a high-finesse signal cavity and delivers a maximum output power of 270 mW to the nonresonant idler wave at 2.92mum , through a 4.5-mm PPRTA crystal. For room-temperature operation and a crystal with a 30-mu;m grating period, pump tuning over 838-848 nm results in OPO tuning over 1.13-1.27mum (signal) and 2.53-3.26mum (idler), limited by the bandwidth of optical coatings. PPRTA exhibits thermal properties superior to those of periodically poled LiNbO(3) .     

Bismuth triborate (BiB3O6) optical parametric oscillators

We report the phase matching of parametric frequency conversion in the nonlinear material BiB₃O₆ (BiBO) and on an investigation of optical parametric oscillators (OPOs) of this new crystal. Based on the calculation of collinear type I and type II phase matching within the refractive-index planes, the most favorable directions for phase matching are identified for OPOs pumped by the fundamental or the harmonics of 1064-nm Nd-doped lasers. Based on these results, pulsed 532-nm-pumped ns OPOs are realized. The pump source is either a Q-switched high repetition rate (10 kHz) Nd:YVO₄ laser (with a pulse energy of 24 J) or a low repetition rate (10 Hz), high pulse energy (120 mJ) Nd:YAG laser system. The BiBO OPO pumped by the Nd:YVO₄ laser showed a very low threshold of 0.047 J/cm². At an average pump power of 2.4 W the total OPO output power was 630 mW. By changing the phase-matching angle within the yz plane from 0 to 11.6° the signal wavelength was tuned from 735 nm to 970 nm, while the spectral width changed from 0.2 nm to 1.4 nm. By pumping the OPO with the Nd:YAG laser, the OPO had a threshold of 0.12 J/cm², a steep slope (59%) and a high total efficiency (of up to 48%). Due to divergence broadening the spectral width changes from 8.5 nm at 800 nm to 70 nm near degeneracy. The properties of BiBO determined from the experimental results are compared with those of well-known nonlinear materials such as BBO, LBO and KTP. PACS 42.65.-k; 42.65.Yj; 42.70.-a; 42.70.Mp     

Efficient Nd:YAG pumped mid-IR laser based on cascaded KTP and ZGP optical parametric oscillators and a ZGP parametric amplifier

Efficient conversion into the mid-IR of a low pulse-energy (2.5 mJ) Nd:YAG laser is achieved by cascaded KTiOPO₄ (KTP) and ZnGeP₂ (ZGP) optical parametric oscillators followed by a ZGP optical parametric amplifier. The first stage 2.13 μm degenerate KTP OPO uses four KTP crystals in a walk-off compensated geometry and an elliptical pump beam focal geometry to produce up to 2.2 W from 6.3 W incident. The 2.13 μm e-ray pumps a Type-I ZGP OPO, which produces 0.5 W of light in the 3.8-4.8 μm spectral region that in turn is amplified by a 2.13 μm o-ray pumped optical parametric amplifier generating 0.84 W with an M² of <2.     

Zig-Zag板条泵浦的2.12μm激光器

 为了实现窄脉宽、高峰值功率2.12 μm激光的稳定输出,设计了基于侧面泵浦Zig-Zag 板条产生1.06 μm基频光,进而泵浦KTP晶体通过II类相位匹配产生2.12 μm激光的光参量振荡实验。对外腔及内腔进行了实验研究,分别获得了1.53%和2.86%的电光转换效率。在20 Hz频率下内腔2.12 μm输出能量达到70 mJ以上,脉宽7 ns~9 ns。其中内腔实验中能量输出稳定度接近8%。     

高亮度人眼安全KTP OPO激光器

采用多模NdYAG激光器泵浦非临界相位匹配的KTP-OPO,获得了光束角2.3 mrad、输出能量400 mJ、平均功率12 W、光-光转换效率40%的1 572 nm激光.泵浦源的参数为能量1 J、重复频率30 Hz.分析认为采用KTP OPO将NdYAG激光器的1 μm激光转换到人眼安全波段的方法是获得1.5 μm激光的最有效的手段之一;非临界相位匹配的KTP OPO的主要优点是大的接受角和无走离,因此即使多纵模激光泵浦情况下也可以获得很高的转换效率.