表面张力法和电导法对比测定表面活性剂临界胶束浓度*

通过比较表面张力法和电导法测定阴离子表面活性剂十二烷基硫酸钠(SDS)和非离子表面活性剂辛基酚聚氧乙烯醚(TX-100)的临界胶束浓度的实验效果,明确了2种方法的优劣。 采用挂环法测试了不同浓度SDS和TX-100水溶液的表面张力,得到了它们的临界胶束浓度以及饱和吸附量、分子截面积;采用电导法研究上述2种表面活性剂溶液的电导率曲线,仅得到SDS的临界胶束浓度。与电导法相比,表面张力法得到的表面活性剂性质信息更多,应用更广泛。该实验使学生加深理解不同电性表面活性剂临界胶束浓度的性质及测定方法,明确不同方法的优缺点,扩大知识面,同时也提高学生处理数据的能力,为学生今后进一步学习应用表面活性剂打下良好基础。     

多元线性回归在混合酸各组分浓度测定中的应用

多元线性回归已广泛用于多组份分光光度分析。本文首次提出在定pH滴定条件下,混合酸各组分浓度与滴定剂体积和溶液pH值之间关系的数学模型,采用多元线性回归求解,可方便地计算出混合酸各组分浓度。该法不需知道被测酸的离解常数,通过对二元、三元及四元混合酸体系分析,证明该法计算方便、分析准确度较好,适用于多组分混合酸的同时分析。     

在线自动配标-离子色谱法同时测定饮用水中7种阴离子的含量

建立了在线自动配标技术同时测定水样中常见阴离子的电导检测-离子色谱分析方法。以较高浓度7种阴离子混合标准母液,通过万通多思(Disino)在线加液单元定量进样4~200μL,7种阴离子进样质量浓度与其峰面积呈良好的线性关系,相关系数均在0.9999以上。水样加标回收率93.6%~106%,测定结果相对标准偏差(RSD)在1.5%~2.8%(n=6)。在线自动配标方法操作简单,准确度好,能够降低在绘制工作曲线中配制梯度浓度的标准样品出现的误差,提高分析效率,能够满足水样中F-、Cl-、NO2、Br、NO3、PO4^3、SO4^27种阴离子的测定要求。     

二甲基甲酰胺-二氧六环混合溶剂中KBr,KSCN及KClO_4的电导研究

本文报告了KBr、KSC N、KClO_4和KI在二甲基甲酰胺(DMF)和1,4-二氧六环混合溶剂中的电导测定值、溶剂的粘度和溶液的密度,按Pitts,Fuoss1978和Lee-Wheaton电导方程拟合实验数据得出溶液的无限稀释摩尔电导A_o,离子缔合常数K_α和正负离子间的距离参数R。对三个方程的适用性和溶液中离子-离子-溶剂分子间的相互作用作了初步讨论。     

双十八烷基二甲基氯化铵水溶液CMC值的测定

采用电导法和荧光法测定了阳离子表面活性剂-双十八烷基二甲基氯化铵(DODAC)的临界胶束浓度(CMC), 在温度为14 ℃时, 电导法测得DODAC溶液的临界胶束浓度为5.24×10-5 mol/L, 荧光法测得DODAC溶液的临界胶束浓度为9.67×10-5 mol/L.     

离子色谱仪流动注射电导法测定过氧化氢

以H2S03与H2O2反应生成H2SO4产生的电导变化与H202的量呈线性关系为理论依据，根据流动注射原理将现有离子色谱仪进行改装成流动注射仪测定过氧化氢。此方法有很好的重现性，8次进样所得相对标准偏差小于2．6％，所得结果稳定，其检测下限为0．5mg/L，标准曲线的相关系数达0．9995。本实验对某些分析条件，诸如H2SO3的浓度和流速、样品用量及反应管长度等因素进行了探讨。由于实际样品中存在不同离子而具有不同背景电导，因而在测定实际样品时采用经过过氧化氢酶处理的样品作空白，以此消除背景电导的干扰。     

转化乳剂的离子电导和光电导研究

本文研究了AgBrCl转化乳剂的离子电导和光电导。随着乳剂中溴含量的增高,其离子电导也随之升高,而光电子寿命则降低。AgBrCl乳剂的离子电导主要取决于其组成;AgBrCl转化乳剂的光电子寿命主要受隙间银子浓度的影响,隙间银离子浓度越大,光电子寿命越短。     

乙二醇对烷基三甲基溴化铵胶团化行为的影响

利用电导法研究了烷基三甲基溴化铵表面活性剂(CnTAB,n=12,14,16),即十二烷基三甲基溴化铵(DTAB),十四烷基三甲基溴化铵(TTAB)和十六烷基三甲基溴化铵(CTAB),在混合极性溶剂乙二醇/水(体积分数0～40%)中的胶团化行为。考察了温度对胶团形成的影响,应用相分离模型估算了三个表面活性剂的胶团热力学参数。结果表明临界胶团浓度(cmc)和反离子解离度(α)都随乙二醇组分的增加而增大。在乙二醇/水混合溶剂中胶团形成的标准吉布斯自由能相差很小,混合焓都是负值,而混合熵都为正值,说明焓-熵补偿效应在胶团形成中起主导作用。     

电导法测定无机盐对十二烷基磺酸钠溶液临界胶束浓度的影响

在40℃时利用电导法测定了无机盐NaCl、KCl、CuCl2、ZnSO4、Fe(NO3)3及AlCl3对十二烷基磺酸钠(SDS)溶液临界胶束浓度(CMC)的影响,并推导了表示无机盐浓度和SDS溶液CMC值之间关系的线性方程.结果表明,随着各种无机盐浓度的增加,SDS溶液的CMC值降低,且不同价态的金属无机盐对SDS溶液...     

比值光谱一阶导数法同时测定苯酚和间苯二酚

以二元混合物的光谱除以其中某一组分的标准光谱而得到的比值光谱，对波长求导，可将重叠光谱分开而消除干扰，从而可方便的完成二组分混合体系中各组分的测定，     

A Study of Heat Conductivity of Methanol-n-Nonanol Binary Mixtures in a Wide Range of Temperatures and Pressures

The heat conductivity of liquid binary mixtures of the system methanol-n-nonanol was measuredat different temperatures, pressures, concentrations. A relationship between the heat conductivity ofthe binary mixtures and the concentration of their components was established.     

Thermal conductivity, thermal effusivity, and specific heat capacity near the lower critical point of the binary liquid mixture n-butoxyethanol-water

Experimental investigations on binary liquid mixtures near the critical mixing point are presently leading to a controversy about the anomaly in the thermal conductivity. A photopyroelectric technique is used to determine the thermal conductivity and the effusivity of the binary liquid mixture n-butoxyethanol-water at its critical concentration near the critical mixing point. It is proven that, contrary to previous reports, there is no critical enhancement in the thermal conductivity. The specific heat capacity is calculated from these results and compared with the results from measurements performed by adiabatic scanning calorimetry.     

Electrical conductivity of systems based on Na3AlF6-SiO2 melt

The electrical conductivity of molten binary and ternary mixtures based on the NaF-AlF₃-SiO₂ system was investigated by means of a tube-cell (composed of pyrolytic boron nitride) with stationary electrodes. An impedance/gain-phase analyser (National Instruments; a high-performance modular chassis controlled by Labview? software) was used for the cell impedance measurement. The conductivity was found to vary linearly with temperature in all the mixtures investigated. The concentration dependence of electrical conductivity (isotherms) thus obtained was divided into two parts. The first represents the concentration region of up to 10 mole % of SiO₂, the second the region with a higher concentration of SiO₂ (from 10 mole % to 40 mole %). While the conductivity decreased considerably with the concentration of SiO₂ in the second part, it increased surprisingly in the low concentration range. From these results, the influence of electrolyte composition and temperature on the electrical conductivity was examined.     

Electrical conductivity of solutions of the LiIO3-HIO3-H2O system

The electrical conductivity of aqueous LiIO₃ solutions and solutions of the LiIO₃-HIO₃-H₂O system is measured over a wide range of compositions at 25, 50, and 75°C. Isothermal surfaces of electrical conductivity are mapped, and the activation energies of conductivity are calculated. The conductivity isotherms in the LiIO₃-H₂O and HIO₃-H₂O boundary binary systems and in mixed solutions along sections with fixed electrolyte ratios each have a maximum as a function of electrolyte concentration. It is assumed that structure reorganization occurs in solutions in the concentration range corresponding to the peak conductivity. Proton migration features in the solutions in question are considered.     

Ternary complexes of palladium(II) and selected amines

Summary The formation and equilibria of the binary and ternary palladium(II) complexes of diethylenetriamine (dien) with other selected amines have been investigated. The results of pH titration measurements allowed the calculation of equilibrium constants, characteristic for the binary and ternary complexes formed. The concentration distribution of various complex species was evaluated and the chelation mode ascertained by conductivity measurements.     

Prediction of pervaporation separation characteristics for the ethanol-water-nylon-4 membrane system

The modified Fels and Huang model has been extended to predict the separation factors and permeabilities more accurately for the system of ethanol-water-nylon-4 membranes. In this system, the binary interaction parameters, g₁₃ and g₂₃, are assumed to be concentration dependent. In order to evaluate these binary interaction parameters, the relationship of the prediction of sorption capability for a given binary mixture into the membrane is developed with and without the consideration of osmotic equilibrium between the polymeric membrane and the binary mixture. The permeabilities of each component for the entire range of the feed mixture at various operating temperatures are then calculated using the predicted sorption capabilities. The experimentally determined diffusion coefficient at zero concentration and the solubility of the pure component are compared with the actual experimental permeabilities. When the osmotic pressure term was taken into consideration, it was found that the calculated individual permeabilities are fairly close to the experimental permeabilities.     

The Electrochemical Grafting of a Mixture of Substituted Phenyl Groups at a Glassy Carbon Electrode Surface

Two‐component substituted aryl groups are simultaneously grafted onto the surface of a glassy carbon electrode by electrochemical reduction of a binary mixture of two aryl diazonium salts in acetonitrile. The electrochemical deposition is achieved potentiostatically and two different mixtures with four different ratios of diazonium salts are used. The binary mixtures comprise: 1) 4‐nitrophenyl diazonium and 4‐bromophenyl diazonium cations and 2) 4‐bromophenyl diazonium and N,N‐diethylaniline diazonium cations. The chemical composition of the two component films is determined by cyclic voltammetry in an electrolyte inert for electroactive groups such as nitrophenyl and bromophenyl. X‐ray photoelectron spectroscopy is also used to evaluate the surface concentration of each grafted substituted phenyl group. The surface concentration of the substituted phenyl group for which the corresponding diazonium cation is the most easily reduced is higher than its concentration in the mixture of the deposition solution. The usefulness of binary films is also discussed.     

Analysis of electric conductivity of binary solid-state catalysts by computer simulation

Experimental and model studies of concentration dependencies of electric conductivity have been performed for a number of binary mechanical mixtures. The physical origins of various peculiarities are discussed with Fe₃O₄+MgO, Fe₃O₄+NiO, and Ni+ZrO₂ systems considered as examples. The degree of friability of the systems and the degree of homogeneity of the component distribution are estimated. A considerable mutual influence of the phases is observed, which is, however, not a chemical interaction.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 1874–1877, November, 1993.     

Stationary concentration establishment in the growing or evaporating droplet of ideal binary solution

The establishment of stationary solution concentration in a growing or evaporating droplet of an ideal binary solution (binary droplet) placed in a vapor mixture of constituting substances and passive gas is described analytically. Relations defining time dependences of solution concentration in a droplet, the number of molecules of each constituting component, and droplet radius are derived at known parameters of the vapor-gas mixture and the initial composition of a binary droplet. The results of calculations of time dependences of aforementioned values are reported for several variants of the initial composition of a droplet and a vapor mixture.     

Dielectric Dispersion and Electric Relaxation Processes Induced by Ionic Conduction in Formamide, 2-Aminoethanol and Their Binary Mixtures

The complex dielectric permittivity, ionic conductivity, electric modulus and impedance spectra of the dipolar molecules formamide (FA), 2-aminoethanol (AE) and their binary mixtures were investigated in the frequency range from 20 Hz to 1 MHz at 303.15 K. Debye-type distributions of the frequency dependent electric modulus and complex impedance were found, corresponding to an ionic conduction relaxation process in the upper frequency regime of the spectra, whereas a spike in the impedance spectra at low frequencies confirms the contribution of an electrode polarization (EP) relaxation process induced by ionic conduction. Due to the high static permittivity of FA, its ionic conductivity was found more than one order of magnitude higher than that of the AE, which is also shown by the comparative values of their EP and ionic conductivity relaxation times. The dependences of dc ionic conductivity values of the binary mixtures on their relaxation times and static permittivity were explored. The concentration dependent static permittivity and the relaxation times led us to infer the formation of a 1:1 H-bonded stable complex between FA and AE molecules with reduction in the number of effective parallel-aligned dipoles.