Optimization of antibiotic analysis in water by solid-phase extraction and high performance liquid chromatography–mass spectrometry/mass spectrometry

This paper describes the development of an optimized method based on solid-phase extraction (SPE) followed by liquid chromatography–electrospray ionization tandem mass spectrometry (LC–MS/MS) for the simultaneous analysis of ten antibiotic compounds including tetracyclines, sulfonamides, macrolides and quinolones. LC–MS/MS sensitivity has been optimized by alterations to both LC and MS operations. Of the two high resolution columns tested, Waters Symmetry C₁₈ endcapped and Agilent Zorbax Bonus-RP, the latter was found to show better performance in producing sharp peaks and clear separation for most of the target compounds. Optimization of the MS fragmentation collision and cone energy enhanced the peak areas of the target analytes. The recovery of the target compounds from water samples was most efficient on Waters Oasis HLB SPE cartridge, while methanol was shown to be the most suitable solvent for desorbing the compounds from SPE. In addition, acidification of samples prior to SPE was shown to enhance the recovery of the compounds. To ensure a satisfactory recovery, the flow rate through SPE should be maintained at ≤10 mL min⁻¹. The method was successfully applied to the analysis of antibiotics from environmental water samples, with concentrations being <LOD in tap water, between <LOD to 28 ng L⁻¹ in river water and between <LOD to 230 ng L⁻¹ in sewage effluent.     

Trace analysis of benzophenone-derived compounds in surface waters and sediments using solid-phase extraction and microwave-assisted extraction followed by gas chromatography–mass spectrometry

This study describes a procedure for determining eight benzophenone-derived compounds in surface waters and sediments. These include the pharmaceutical ketoprofen, its phototransformation products 3-ethylbenzophenone and 3-acetylbenzophenone, and five benzophenone-type ultraviolet (UV) filters. The proposed analytical method involves the pre-concentration of water samples by solid-phase extraction (SPE) and microwave-assisted extraction (MAE) of sediment samples followed by derivatization and analysis by gas chromatography–mass spectrometry. Different parameters were investigated to achieve optimal method performance. Recoveries of 91 to 96 % from water samples were obtained using HLB Oasis SPE cartridges, whereas MAE of sediments (30 min at 150 °C) gave recoveries of 80 to 99 %. Limits of detection were between 0.1 and 1.9 ng L^?1 for water samples and from 0.1 to 1.4 ng g^?1 for sediment samples. The developed method was applied to environmental samples and revealed the presence of UV filters in the majority of the surface waters with up to 690 ng L^?1 of 2-hydroxy-4-methoxybenzophenone. By contrast, ketoprofen (≤2,900 ng L^?1) and its degradation products (≤320 ng L^?1) were found in only two rivers, both receiving wastewater treatment plant effluents. Sediment analysis revealed benzophenone to be present in concentrations up to 650 ng g^?1, whereas concentrations of other compounds were considerably lower (≤32 ng L^?1). For the first time, quantifiable amounts of two ketoprofen transformation products in the aqueous environment are reported.     

Pharmaceutical trace analysis in aqueous environmental matrices by liquid chromatography–ion trap tandem mass spectrometry

An analytical method based on solid-phase extraction followed by liquid chromatography tandem mass spectrometry with an ion trap analyser was developed and validated for the quantification of a series of pharmaceutical compounds with distinct physical–chemical characteristics in estuarine water samples. Method detection limits were between 0.03 and 16.4 ng/L. The sensitivity and the accuracy obtained associated with the inherent confirmatory potential of ion trap tandem mass spectrometry (IT-MS/MS) validates its success as an environmental analysis tool. Two MS/MS transitions were used to confirm compound identity. Almost all pharmaceuticals were detected at ng/L level in at least one sampling site of the Douro River estuary, Portugal.     

Analysis of pharmaceuticals in indirect potable reuse systems using solid-phase extraction and liquid chromatography–tandem mass spectrometry

A solid-phase extraction (SPE) LC–MS/MS method for 18 commercial drugs in secondary wastewater and product water from water recycling plants using microfiltration (MF) and reverse osmosis (RO) has been developed, optimised and validated. The method incorporates a range of multi-class pharmaceuticals including lipid lowering agents, analgesics, antipyretics, non-steroidal anti-inflammatory drugs, antidepressants, anticoagulants, tranquilizers, cytostatic agents, and antiepileptics. Method limits of quantitation (MLQs) in secondary wastewater ranged from 15 to 250 ng/L, while MLQs in post-RO water ranged from 1 to 25 ng/L. Results from analysis of secondary wastewater from Western Australia are presented, and represent the largest survey of non-antibiotic pharmaceuticals within Australia to date. Analysis of post-RO water from two MF/RO water recycling facilities also demonstrate that MF/RO treatment removes most pharmaceuticals to below the analytical limits of detection, and more importantly, up to seven orders of magnitude below health-based guideline values.     

Screening of drugs in equine plasma using automated on-line solid-phase extraction coupled with liquid chromatography–tandem mass spectrometry

A rapid liquid chromatography–tandem mass spectrometry (LC–MS–MS) method was developed for the simultaneous screening of 19 drugs of different classes in equine plasma using automated on-line solid-phase extraction (SPE) coupled with a triple quadrupole mass spectrometer. Plasma samples were first protein precipitated using acetonitrile. After centrifugation, the supernatant was directly injected into the on-line SPE system and analysed by a triple quadrupole LC–MS–MS in positive electrospray ionisation (+ESI) mode with selected reaction monitoring (SRM) scan function. On-line extraction and chromatographic separation of the targeted drugs were performed using respectively a polymeric extraction column (2 cm L × 2.1 mm ID, 25 μm particle size) and a reversed-phase C18 LC column (3 cm L × 2.1 mm ID, 3 μm particle size) with gradient elution to provide fast analysis time. The overall instrument turnaround time was 9.5 min, inclusive of post-run and equilibration time. Plasma samples fortified with 19 targeted drugs including narcotic analgesics, local anaesthetics, antipsychotics, bronchodilators, mucolytics, corticosteroids, sedative and tranquillisers at sub-parts per billion (ppb) to low parts per trillion (ppt) levels could be consistently detected. No significant matrix interference was observed at the expected retention times of the targeted ion transitions. Over 70% of the drugs studied gave detection limits at or below 100 pg/mL, with some detection limits reaching down to 19 pg/mL. The method had been validated for extraction recovery, precision and sensitivity, and a blockage study had also been carried out. This method is used regularly in the authors’ laboratory to screen for the presence of targeted drugs in pre-race plasma samples from racehorses.     

Rapid determination of five antibiotic residues in swine wastewater by online solid-phase extraction–high performance liquid chromatography–tandem mass spectrometry

A simple and quick online solid-phase extraction (SPE) coupled to liquid chromatography (LC)/tandem mass spectrometry (MS/MS) for the determination of the five antibiotics (florfenicol, FF; lincomycin, LCM; oxytetracyclin, OTC; tylosin, TS; valnemulin, VLM) in swine wastewater has been developed. After filtration, aliquots (100 μl) of wastewater samples were directly injected to a column-switching LC system. Some matrix interference was removed by washing up SPE column with 0.2% formic acid solution and acetonitrile. Antibiotics eluted from SPE column were separated on analytical column by converting switching valve and were detected by MS/MS. Calibration curves using the method of standard addition had very good correlation coefficients (r > 0.99) in the range of 0.1 to 2 ng/ml. The intra-day precision of the method was less than 12% and the inter-day precision was between 6 to 17%. The detection limits were 0.01–0.1 ng/ml. When this method was applied to wastewater samples in swine facilities, four compounds (LCM, OTC, TS, and VLM) were detected.     

Sampling of benzene in environmental and exhaled air by solid-phase microextraction and analysis by gas chromatography–mass spectrometry

Benzene is classified as a Group I carcinogen by the International Agency for Research on Cancer (IARC). The risk assessment for benzene can be performed by monitoring environmental and occupational air, as well as biological monitoring through biomarkers. The present work developed and validated methods for benzene analysis by GC/MS using SPME as the sampling technique for ambient air and breath. The results of the analysis of air in parks and avenues demonstrated a significant difference, with average values of 4.05 and 18.26 μg m⁻³, respectively, for benzene. Sampling of air in the occupational environment furnished an average of 3.41 and 39.81 μg m⁻³. Moreover, the correlations between ambient air and expired air showed a significant tendency to linearity (R ² = 0.850 and R ² = 0.879). The results obtained for two groups of employees (31.91 and 72.62 μg m⁻³) presented the same trend as that from the analysis of environmental air.     

Determination of fecal sterols by gas chromatography–mass spectrometry with solid-phase extraction and injection-port derivatization

Injection-port derivatization combined with solid-phase extraction (SPE) was developed and applied for the first time to determine five types of fecal sterols (coprostanol, cholestanol, epicholestanol, epicoprostanol and cholesterol) with gas chromatography–mass spectrometry (GC–MS). In this method, silylation of fecal sterols was performed with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) at GC injection-port. The factors influential to this technique such as injection-port temperature, purge-off time, derivatization reagent (BSTFA) volume, and the type of organic solvent were investigated. In addition, the conditions of SPE (including the type of SPE cartridge, the type of elution organic solvent) were also studied. After SPE followed by injection-port silylation by GC–MS, good linearity of analytes was achieved in the range of 0.02–10 ng/mL with coefficients of determination, R² > 0.995. Good reproducibility was obtained with relative standard deviation less than 19.6%. The limits of detection ranged from 1.3 ng/mL to 15 ng/mL (S/N = 3) in environmental water samples. Compared with traditional off-line silylation of fecal sterols performed with water bath (60 °C, 30 min), this injection-port silylation method is much simpler and convenient. The developed method has been successfully applied for the analysis of fecal sterols from real environmental water samples.     

Online solid-phase extraction–liquid chromatography–electrospray–tandem mass spectrometry determination of multiple classes of antibiotics in environmental and treated waters

An online solid-phase extraction and liquid chromatography in combination with tandem mass spectrometry method was developed for the simultaneous determination of 31 antibiotics in drinking water, surface water and reclaimed waters. The developed methodology requires small sample volume (10 mL), very little sample preparation and total sample run time was 20 min. An Ion Max API heated electrospray ionization source operated in the positive mode with two selected reaction monitoring transitions was used per antibiotic for positive identity and quantification performed by the internal standard approach, to correct for matrix effects and any losses in the online extraction step. Method detection limits were in the range of 1.2–9.7, 2.2–15, 5.5–63 ng/L in drinking water, surface water and reclaimed waters, respectively. The method accuracy in matrix spiked samples ranged from 50–150 % for the studied antibiotics. The applicability of the method was demonstrated using various environmental and reclaimed water matrices. Erythromycin was detected in more than 85 % of the samples in all matrices (28–414, n.d.–199, n.d.–66 ng/L in reclaimed, river and drinking waters respectively). The other frequently detected antibiotics in reclaimed waters were nalidixic acid, clarithromycin, azithromycin, trimethoprim, and sulfamethoxazole.     

Determination of five nitrobenzoic acids in groundwater by solid-phase extraction and liquid chromatography–mass spectrometry

A method involving solid-phase extraction (SPE) and reversed-phase liquid chromatography–mass spectrometry (LC–MS) has been developed for determination, in groundwater, of nitrobenzoic acids associated with 2,4,6-trinitrotoluene production. Pre-concentration on a co-polymer-based SPE cartridge enabled quantitative extraction of the analytes from water. Investigation of negative ion electrospray and atmospheric-pressure chemical ionization mass spectrometry indicated the sensitivity of APCI was more than twice that of ESI. An ¹⁵N-labeled internal standard was used to achieve more accurate quantitation and mass assignment. Recovery was better than 80% when 10 mL water was extracted with the SPE cartridge. Combination of SPE with LC–MS analysis resulted in method detection limits of less than 5 μg L⁻¹. The method has been used for analysis of groundwater samples collected from a site of a former ammunition plant. Contamination with nitrobenzoic acids was determined at μg L⁻¹ levels.     

Trace analysis of environmental matrices by large-volume injection and liquid chromatography–mass spectrometry

The time-honored convention of concentrating aqueous samples by solid-phase extraction (SPE) is being challenged by the increasingly widespread use of large-volume injection (LVI) liquid chromatography–mass spectrometry (LC–MS) for the determination of traces of polar organic contaminants in environmental samples. Although different LVI approaches have been proposed over the last 40 years, the simplest and most popular way of performing LVI is known as single-column LVI (SC-LVI), in which a large-volume of an aqueous sample is directly injected into an analytical column. For the purposes of this critical review, LVI is defined as an injected sample volume that is ≥10% of the void volume of the analytical column. Compared with other techniques, SC-LVI is easier to set up, because it requires only small hardware modifications to existing autosamplers and, thus, it will be the main focus of this review. Although not new, SC-LVI is gaining acceptance and the approach is emerging as a technique that will render SPE nearly obsolete for many environmental applications. In this review, we discuss: the history and development of various forms of LVI; the critical factors that must be considered when creating and optimizing SC-LVI methods; and typical applications that demonstrate the range of environmental matrices to which LVI is applicable, for example drinking water, groundwater, and surface water including seawater and wastewater. Furthermore, we indicate direction and areas that must be addressed to fully delineate the limits of SC-LVI.     

Determination of 16 polycyclic aromatic hydrocarbons in environmental water samples by solid-phase extraction using multi-walled carbon nanotubes as adsorbent coupled with gas chromatography–mass spectrometry

A solid-phase extraction (SPE) using multi-walled carbon nanotubes (MWCNTs) as adsorbent coupled with gas chromatography–mass spectrometry (GC–MS) method was developed for the determination of 16 polycyclic aromatic hydrocarbons (PAHs) in environmental water samples. Several condition parameters, such as extraction adsorbents, elution solvents and volumes, and sample loading flow rate and volume were optimized to obtain high SPE recoveries and extraction efficiency. 150 mg MWCNTs as sorbent presented high extraction efficiency of 16 PAHs due to the large specific surface area and high adsorption capacity of MWCNTs compared with the commercial C18 column (250 mg/2 mL). The calibration curves of 16 PAHs extracted were linear in the range of 20–5000 ng L⁻¹, with the correlation coefficients (r²) between 0.9848 and 0.9991. The method attained good precisions (relative standard deviation, RSD) from 1.2% to 12.1% for standard PAHs aqueous solutions; method recoveries ranged in 76.0–125.5%, 74.5–127.0%, and 70.0–122.0% for real spiked samples from river water, tap water and seawater, respectively. Limits of detection (LODs, S/N = 3) of the method were determined from 2.0 to 8.5 ng L⁻¹. The optimized method was successfully applied to the determination of 16 PAHs in real environmental water samples.     

Dispersive solid-phase extraction followed by liquid chromatography–tandem mass spectrometry for the multi-residue analysis of pesticides in raw bovine milk

A fast multi-residue method based on dispersive solid-phase extraction (DSPE) followed by liquid chromatography–tandem mass spectrometry was developed for the simultaneous determination of 44 pesticides in raw bovine milk. Raw bovine milk samples did not percolate through SPE cartridges usually applied for pesticide extraction from homogenized pasteurized milk samples. Therefore, a DSPE technique was implemented and validated for the first time in this work. Graphitized non-porous carbon and C18 modified silica materials were tested both in combination with magnesium sulfate and bonded silica with ethylenediamine-N-propyl phase. The efficiency of the DSPE process was studied at several concentration levels obtaining the higher recoveries with C18 material. The method performance was also assessed and the limits of quantification reached the ng g⁻¹ level, complying with the most recent maximum residue levels. The DSPE method was also shown to be suited to both the fatty and skimmed fractions issued from raw milk. Finally, the extraction method was successfully applied to the analysis of raw milk samples collected in 23 farms of dairy cattle from NW Spain (Galicia).     

Continuous solid-phase extraction and gas chromatography–mass spectrometry determination of pharmaceuticals and hormones in water samples

A semi-automatic flow-based method for the simultaneous determination of 9 pharmaceuticals and 3 hormones in water samples in a single analytical run is proposed. The analytes were retained on a solid-phase extraction sorbent column and 1 μL of the eluate analysed by gas chromatography in combination with electron impact ionization mass spectrometry in the SIM mode. The sorbent used, Oasis-HLB, provided near-quantitative recovery of all analytes. The proposed method was validated with quite good analytical results including low limits of detection (0.01–0.06 ng L⁻¹ for 100 mL of water) and good linearity (r² > 0.993) throughout the studied concentration ranges. The method provided good accuracy (recoveries of 85–103%) and precision (between- and within-day RSD values less than 7%) in the determination of the pharmaceuticals and hormones in tap, river, pond, well, swimming pool and wastewater.     

Quantitative determination of 22 primary aromatic amines by cation-exchange solid-phase extraction and liquid chromatography–mass spectrometry

Primary aromatic amines (PAAs) have been broadly studied due to their high toxicity. In this work a method for the analysis of 22 PAAs in aqueous simulants has been developed. The method is based on a solid-phase extraction step using cation-exchange cartridges and the subsequent analysis of the extracts by ultra-high-performance liquid chromatography with mass spectrometric detection. The recoveries obtained for all the amines analyzed ranged between 81 and 109%, linear range was between 0.03 and 75 μg L⁻¹, with the RSD values between 4.5 and 13.4% and an average value of 7.5% and limits of detection at μg L⁻¹ level. The method has been applied to two real samples obtained from migration experiments of polyurethane based laminates to simulant B (water with 3% (w/v) acetic acid) which represents the worst case for the migration of aromatic amines. The main amines found in both samples were methylenedianiline isomers, obtained from the corresponding residual diisocyanates used during polyurethane adhesive polymerization. The total amine concentration found was 26 and 6.3 μg of aniline equivalents per kg of food simulant.     

Analysis of dinitro- and amino-nitro-toluenesulfonic acids in groundwater by solid-phase extraction and liquid chromatography–mass spectrometry

A reversed-phase LC–MS method with quadrupole-time of flight (QTOF) detection has been developed for the determination of four dinitro-toluenesulfonic acids and two amino-nitro-toluenesulfonic acids in groundwater. The analytes were separated by HPLC with 0.1% (v/v) formic acid as mobile phase modifier compatible with mass spectrometric detection. QTOF-MS analysis with negative ion electrospray ionization afforded good selectivity and sensitivity for analysis of the dinitro- and amino-nitro-toluenesulfonic acids. Structure elucidation and confirmation were accomplished by tandem mass spectrometry. Characteristic ions resulting from the loss of NO, NO₂, and SO₂ from the [M–H]^– ions were detected. An intense fragment ion at m/z 80 representing the [SO₃]^– ion was detected for all dinitro- and amino-nitro-toluenesulfonic acids. Solid-phase extraction using a co-polymer cartridge was developed for preconcentration of the analytes from water. Good recovery (>85%) was achieved when 0.1% formic acid was added into the water samples before extraction. Method detection limits ranged from 10 to 76 ng L^–1 for the targeted compounds when 10 mL water was analyzed. Groundwater samples collected from wells close to a former ammunition plant in Stadtallendorf, Germany, were analyzed for the dinitro- and amino-nitro-toluenesulfonic acids.