甲醇/TiO2(110)界面激发态的表征

用光电子能谱的方法研究了甲醇/TiO₂(110)界面的电子结构．在激发波长为400 nm的双光子光电子能谱(2PPE)中,探测到了一个末态能量在费米能级以上5.5 eV的共振信号．之前的研究[Chem. Sci. 1, 575 (2010)]表明,这个共振信号与甲醇在5配位的钛离子(Ti_5c)上的光催化解离相关．双光子光电子能谱同时携带初态和中间态的信息．为此设计了一个调谐激发光波长的2PPE实验以及一个单光子光电子能谱(1PPE)和2PPE对比的实验,结果一致表明这个共振信号来自于未占据的中间态,也就是激发态．能带色散关系测量表明这个激发态是局域的．时间分辨2PPE测得这个激发态的寿命是24 fs．     

反应物转动激发对F+H2→HF+H体系反应动力学的影响

利用高分辨的交叉分子束装置研究了F+H₂(v=0,j=0, 1)反应在碰撞能1.27 kcal/mol下的动力学行为, 获得了产物HF(v′=1,2,3)转动态分辨的微分散射截面．当反应物H₂ 处于不同转动量子态j=0和1时,产物HF(v′=2)的散射角分布都主要表现为后向散射,但HF(v′=2)的转动态布居与反应物的转动量子态密切相关,转动激发的H₂分子将产生转动“更热”的HF(v′=2) 产物．另外,对于HF(v′=3)产物通道,由于slow-down机理的影响,当H₂布居于j=0时前向散射表现更显著．     

锐钛矿型二氧化钛纳米粉体的IR光谱与光催化性能研究

采用溶胶-凝胶法制备了TiO2光催化剂,研究了不同温度下焙烧TiO2粉体的XRD和FT-IR光谱。400℃焙烧后,相应有机物的红外吸收峰消失,随着焙烧温度的升高,粉体粒径变大,800-420cm-1之间的吸收峰逐渐锐化,700℃焙烧的FT-IR谱的423cm-1为金红石型TiO2的特征Ti-O键振动。500℃焙烧的锐钛矿型TiO2粉体对水杨酸具有较好的光催化活性。     

甲醇在纳米TiO2作用下进行光催化氧化反应的机理研究

以纳米TiO2 为催化剂 ,以主波长为 36 4nm的汞灯为光源 ,用气相色谱法分别考察了 0 .1mol/L的甲醇、甲醛和甲酸水溶液进行光催化氧化反应的动力学规律 .Langmuir Hinshelwood方程进行核算结果证明 ,该组反应均为零级反应 .用TEM、XRD、SSA和XPS对催化剂进行表征 .根据XPS的检测结果提出了甲醇光催化氧化的反应机理 .TiO2 光激发活化时间约为 30～ 6 0min ,生成物及剩余反应物浓度随时间变化的曲线表明 ,该反应速率为HCH2 OH 相似文献   

二氧化钛多孔膜的UV-Vis光谱与光催化性能研究

以钛酸四丁酯(Ti(OBu)4)、乙醇胺(MEA)、聚乙二醇(PEG)和无水乙醇为反应体系,采用溶胶-凝胶法制备了TiO2溶胶并通过浸渍提拉法制得了TiO2多孔膜,用UV-Vis,XRD和AFM对制得的多孔膜进行了表征,讨论了薄膜的紫外-可见透过光谱随着薄膜层数的变化规律以及其与膜厚的关系,结果表明在本实验条件下薄膜转移得很均匀,每层膜厚度约为60nm。多孔膜的光催化测试结果表明,随着薄膜层数的增加,光催化活性也逐渐增强,10层多孔膜的光催化活性最高。     

光电子能谱研究Ce表面的氧化

利用光电子能谱技术研究了室温Ｃｅ膜表面的氧化，分析了在不同氧气暴露量下，稀土金属Ｃｅ氧化状态和样品功函数的变化，结果表明，在Ｏ２吸会的过程中，生成两种Ｃｅ的氧化物，在低的暴露量时，氧在Ｃｅ表面的吸队十分迅速，生成Ｃｅ２Ｏ３，同时，Ｃｅ２Ｏ３中的Ｃｅ３ｄ和Ｏｌｓ谱峰随着氧气暴露量的增加向低结合能方向漂移，在高的暴露量下，氧在表面的吸附趋子缓慢，表面的Ｃｅ２Ｏ３被氧化成ＣｅＯ２，通过对样品加热，能使得     

XPS研究Nd表面氧化物的生长过程

用X射线光电子能谱(XPS)研究新鲜Nd表面在不同氧气和空气进气量的情况下,表面氧化物的生长过程.发现氧化层由氧化物、氢氧化物及表面化学吸附水三种成分,这三种成分的增加与进气量都存在正比对数关系,氧化物和吸附水在一定进气量后趋于饱和,而氢氧化物持续不断增加,最终氢氧化物占据主要地位. 关键词： X射线光电子能谱(XPS) Nd 氧化     

Ag在CeO2-x(111)薄膜上的生长与电子结构

利用XPS和RPES技术研究了CeO_2-x(111)薄膜表面上的氧空位对Ag纳米颗粒的生长和电子结构的影响. XPS结果表明,室温下,Ag纳米颗粒在部分还原的CeO_2-x(111)薄膜上呈三维岛状生长, 并且岛密度比完全氧化的CeO₂(111)薄膜表面上的大, 说明氧空位可以作为Ag纳米粒子生长的中心. Ag3d_5/2芯能级的结合能随着Ag颗粒尺寸的减小而增大, 主要来源于终态效应的贡献. Ag和CeO_2-x     

用CVD法在活性炭上镀二氧化钛薄膜光催化降解酸性品红

用常压化学气相沉积法在活性炭上镀二氧化钛薄膜,通过紫外光照射对酸性品红进行降解研究.其结果表明:活性炭的用量、溶液中加入不同物质、镀薄膜时水的温度均对酸性品红的转化率有影响.经过实验找到了较好的光催化条件.实验得出可以利用太阳光催化降解染料.     

二氧化钛薄膜表面甲醇吸附的和频振动光谱

自行搭建了用于研究表面光催化的宽带红外和频振动光谱并可以原位紫外光激发的装置. 利用自制的结构紧凑小巧的高真空样品池,可以在10 kPa氧气氛围下经原位紫外光照除掉 射频磁控溅射制备的二氧化钛薄膜表面的有机污染物. 通过在室温下改变甲醇气压和指认吸附在薄膜表面的甲醇的和频振动光谱,发现薄膜表面有两种吸附的甲醇,分子形式吸附的甲醇(CH₃OH)和解离吸附的甲醇(CH₃O). 当甲醇的覆盖度由低变高时,分子形式吸附的甲醇的CH₃的对称伸缩振动和费米共振峰红移了6～8 cm^-1. 真空下,薄膜表面的甲氧基和表面的氢原子可以重新结合并以甲醇分子的形式脱附. 研究表明二氧化钛薄膜体系存在两个平衡：气相甲醇和表面吸附的甲醇分子之间,以及表面吸附的甲醇分子和甲氧基之间.     

CH3OH/TiO2(110)界面的光电子能谱研究

Methanol/TiO₂(110) is a model system in the surface science study of photocatalysis where methanol is taken as a hole capture. However, the highest occupied molecular orbital of adsorbed methanol lies below the valence band maximum of TiO₂, preventing the hole transfer. To study the level alignment of this system, electronic structure of methanol covered TiO₂(110) surface has been measured by ultraviolet photoelectron spectroscopy and the molecular orbitals of adsorbed methanol have been clearly identified. The results indicate the weak interaction between methanol and TiO₂ substrate. The static electronic structure also suggests the mismatch of the energy levels. These static experiments have been performed without band gap excitation which is the prerequisite of a photocatalytic process. Future study of the transient electronic structure using time-resolved UPS has also been discussed.     

乙醇在TiO2(110)表面光催化解离的动力学和超快电子动态学 (cited: 2)

采用实时双光子光电子能谱和时间分辨双光子光电子能谱技术分别研究了乙醇在该表面光催化解离的动力学和超快电子动态学过程. 通过测量与乙醇光催化解离相关的电子激发态随时间的演化,发现这个反应满足分型动力学. 乙醇在还原性TiO₂(110)上的光催化解离比在氧化性表面快,这归结于缺陷的存在降低了反应能垒. 这样一个反应的加速过程很可能是与缺陷电子相关的. 通过干涉双脉冲相关的测量,得到了乙醇-TiO₂界面电子激发态的超快动态学. 与甲醇的情况类似,这个电子激发态的寿命为24 fs. 激发态的出现为TiO₂和它周围环境的电子转移提供了一个通道.     

表面桥氧空位对甲醛在二氧化钛表面吸附的影响

Oxygen vacancy (O_v) has significant influence on physical and chemical properties of TiO₂ systems,especially on surface catalytic processes.In this work,we investigate the effects of O v on the adsorption of formaldehyde (HCHO) on TiO₂(110) surfaces through firstprinciples calculations.With the existence of O_v,we find the spatial distribution of surface excess charge can change the relative stability of various adsorption configurations.In this case,the bidentate adsorption at five-coordinated Ti (Ti_5c) can be less stable than the monodentate adsorption.And HCHO adsorbed in O_v becomes the most stable structure.These results are in good agreement with experimental observations,which reconcile the long-standing deviation between the theoretical prediction and experimental results.This work brings insights into how the excess charge affects the molecule adsorption on metal oxide surface.     

Development of rf plasma sputtered Al2O3-TiO2 multilayer broad band antireflecting coatings and its correlation with plasma parameters

TiO₂/Al₂O₃/TiO₂/Al₂O₃ multilayer structures were obtained at different oxygen:argon gas ratios of 20:80, 30:70, 50:50 and 60:40 sccm and constant rf power of 200 W using reactive magnetron sputtering. Grain size and elemental distribution in the films were studied from AFM image and XPS spectra respectively. The deposited grain size increased with increasing oxygen:argon gas ratio. The optical band gap, refractive index, extinction coefficient were calculated from UV-vis transmittance and reflectance spectra. It was observed that the value of refractive index, extinction coefficient and band gap increased with increasing oxygen. These variations are due to the defects levels generated by the heterostructure and explained by the PL spectrum. The antireflecting (AR) efficiency of the films was estimated from the reflectance spectra of the films. Broad band antireflecting coating for the visible range was achieved by varying oxygen content in the film. The plasma chemistry controlled the antireflecting property by the interface interdiffusion of atoms during layer transition in multilayer deposition. The in situ investigation of the plasma chemistry was performed using optical emission spectroscopy. The plasma parameters were estimated and correlated with the characteristics of the films.     

Titania deposited on soft magnetic activated carbon as a magnetically separable photocatalyst with enhanced activity

Magnetically separable composite photocatalysts, TiO₂ deposited on soft magnetic ferrite activated carbon (TFAC), were prepared by sol-gel and dip-coating technique. The prepared composites were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectra (FTIR), optical absorption spectroscopy, vibrating sample magnetometer (VSM) and nitrogen adsorption. These photocatalysts exhibited enhanced photocatalytic activity compared to Degussa P25 for the degradation of methyl orange (MO) in aqueous solution. The kinetics of MO degradation was well fitted to the Langmuir-Hinshelwood model. The samples showed good magnetic response and could be completely recovered by an external magnet. Furthermore, the photocatalysts could maintain high photocatalytic activity after five cycles, and the degradation rate of MO was still close to 90%.     

Investigation of chemical decomposition of CCl4 on TiO2 near room temperature

Dissociative adsorption of CCl₄ on TiO₂ at 35 °C has been studied by Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and electron spin resonance. CCl₄ decompose to form CO, CO₂, and CO₃ on the surface, at such a low temperature, in which CO₂ formation is not from CO oxidation on TiO₂, but CO₃ can be produced by CO and CO₂ adsorption. The Cl generated from CCl₄ decomposition is left on the surface and bonded to titanium ions. Mineralization of CCl₄ on TiO₂ involves the lattice oxygens. Thermodynamical driving force and possible reaction routes for CO and CO₂ formation in the CCl₄ decomposition on TiO₂ are discussed.     

The structure of ordered Au films on TiOx

The growth of Au on an ultra-thin, ordered Mo(1 1 2)-(8 × 2)-TiO_x, was investigated using scanning tunneling microscopy (STM), low energy ion scattering spectroscopy (LEISS), X-ray photoelectron spectroscopy (XPS), and temperature programmed desorption (TPD). Wetting of the TiO_x surface by Au was observed with STM and LEISS, and the ordering of the Au films was atomically resolved with STM. TPD showed that Au binds more strongly to the reduced TiO_x film than to bulk TiO₂, but more weakly than to the Mo substrate. The Au-TiO_x binding energy is greater than Au-Au in bulk Au. The oxidation state of Ti in the TiO_x film was deduced by XPS and from the Ti-O phonon shifts relative to bulk TiO₂. The TiO_x/Mo(1 1 2) film structure and those for the (1 × 1)- and (1 × 3)-Au/TiO_x/Mo(1 1 2) surfaces are discussed.     

The application of Raman and anti-stokes Raman spectroscopy for in situ monitoring of structural changes in laser irradiated titanium dioxide materials

The use of Raman and anti-stokes Raman spectroscopy to investigate the effect of exposure to high power laser radiation on the crystalline phases of TiO₂ has been investigated. Measurement of the changes, over several time integrals, in the Raman and anti-stokes Raman of TiO₂ spectra with exposure to laser radiation is reported. Raman and anti-stokes Raman provide detail on both the structure and the kinetic process of changes in crystalline phases in the titania material. The effect of laser exposure resulted in the generation of increasing amounts of the rutile crystalline phase from the anatase crystalline phase during exposure. The Raman spectra displayed bands at 144 cm⁻¹ (A1g), 197 cm⁻¹ (Eg), 398 cm⁻¹ (B1g), 515 cm⁻¹ (A1g), and 640 cm⁻¹ (Eg) assigned to anatase which were replaced by bands at 143 cm⁻¹ (B1g), 235 cm⁻¹ (2 phonon process), 448 cm⁻¹ (Eg) and 612 cm⁻¹ (A1g) which were assigned to rutile. This indicated that laser irradiation of TiO₂ changes the crystalline phase from anatase to rutile. Raman and anti-stokes Raman are highly sensitive to the crystalline forms of TiO₂ and allow characterisation of the effect of laser irradiation upon TiO₂. This technique would also be applicable as an in situ method for monitoring changes during the laser irradiation process.