Effects of drying and pressing on the pore structure in the cellulose fibre wall studied by 1H and 2H NMR relaxation

A 1H and 2H NMR relaxation method was used to investigate the influence of drying and pressing on the pore size and pore size distribution in the cellulose fibre wall. The investigation was made in the moisture interval in which cellulose fibres normally shrink, i.e. from a moisture ratio of about 1.5 g water/g fibre to dry fibres. When the moisture content of a fibre sample was decreased by drying or pressing, the pores decreased in size and the pore size distribution became narrower. It was found that there were only small differences at a given moisture content between the pore size distributions of samples prepared by drying and by pressing. The results also indicate that the pore shrinkage in cellulose fibres during pressing or drying is a process in which the cell wall pores of a wet cellulose fibre successively shrink as the moisture content decreases. It was observed that, at low moisture contents, pressing and drying resulted in different 1H NMR spin-lattice relaxation profiles. This is discussed in terms of morphology differences in the fibre matrix. The mobility of the protons in the solid phase influences the liquid 1H NMR spin-lattice relaxation in heterogeneous systems through magnetization transfer. We have also studied the effects of hornification in recycled pulps     

Effects of oxygen plasma treatment on the surface of bisphenol A polycarbonate: a study using SIMS,principal component analysis,ellipsometry, XPS and AFM nanoindentation

The effects of oxygen plasma treatment and the subsequent air exposure on the surface composition and properties of bisphenol A polycarbonate (BPA‐PC) were analysed by X‐ray photoelectron spectroscopy (XPS), ellipsometry, static time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) with principal component analysis (PCA) and nanoindentation using an atomic force microscope (AFM). PCA showed systematic changes in the film chemistry after short treatment times (0.1 s), with the main sites of attack being the carbonate and aromatic ring structure. On the basis of this multitechnique analysis, it was unambiguously determined that extended oxygen plasma treatment times resulted in the formation of low‐molecular‐weight material (LMWM) within the first 50 nm on the surface, and not in a cross‐linked skin as has been proposed by other researchers. The study shows that controlled surface modification of BPA‐PC polymers is possible, allowing surface oxygen incorporation without degradation of the polymer structure. This result is relevant for improved adhesion of coatings applied to BPA‐PC polymers. Copyright © 2006 John Wiley & Sons, Ltd.     

Structure and microporous formation of cellulose/silk fibroin blend membranes: Part II. Effect of post-treatment by alkali

Blend membranes (RCF1) were prepared from mixture solution of cellulose and silk fibroin (SF) in cuoxam by coagulating with acetone–acetic acid (4:1 by volume). The blend membranes were subjected to post-treatment with 10% NaOH aqueous solution, and their structure and properties were characterized by FT-IR, X-ray diffraction, DSC, SEM and DMTA. In previous work, cellulose/SF blend membranes (RCF2) prepared by coagulating with 10% NaOH aqueous solution formed a microporous structure, in which the SF as a pore former was almost completely removed from the membrane. However, when the blend membranes RCF1 were immersed in 10% NaOH aqueous solution for post-treatment, a strong hydrogen bonding between cellulose and SF inhibited the removal of SF. Although alkali is a good solvent for SF, the blend membranes RCF1 such obtained from cellulose and SF were alkali resistant. The crystallinity and the mean pore size of the blend membranes slightly decreased with increasing post-treatment time. This work provided a cellulose/silk blend membrane, which can be used under alkaline medium.     

Characteristics of CuAl<Subscript>2</Subscript>-Cu<Subscript>9</Subscript>Al<Subscript>4</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposites synthesized by mechanical treatment

Summary Reactive milling of Cu-hydroxycarbonate - powder aluminium mixture brings many complex chemical reactions such as decomposition, aluminothermic reduction and mechanical alloying resulting in the formation of nanometer size composites that contain intermetallic phases, -Cu₉Al₄ and -CuAl₂, with aluminium oxide.