On-line detection of emulsion polymerization by solid-state NMR spectroscopy

 The on-line detection of emulsion polymerization processes by means of solid-state NMR spectroscopy is demonstrated for the first time using poly(butyl acrylate) as a model system. Relatively short time intervals are accessible via ¹H detection while the use of ¹³C NMR spectroscopy results in an increased spectral resolution. Details of sample preparation and experimental techniques are given, while remaining artifacts of the preliminary results will be addressed in further investigations. Received: 7 November 1997 Accepted: 5 January 1998     

Behavior of bound water in polyethylene oxide studied by DSC and high-frequency spectroscopy.

Measurements of DSC, NMR and high-frequency spectroscopy have been done on PEO-H2O and PEO-H2O-HQ mixed systems. DSC measurements show that water molecules contained in PEO are divided roughly into two species: freezable water and non-freezable water. By 1H-NMR measurements, PEO and H2O protons show an absorption peak around 3.6 ppm and 4.5 ppm, respectively. All the PEO-H2O samples containing H2O show NMR absorption signals, suggesting the existence of movable H2O. Samples with H2O molar ratio over 0.5, show one absorption peak of H2O protons, and more than two peaks of PEO. The results from DSC and NMR measurements show that the bound state of H2O in PEO, as well as the mobility of PEO itself, varies according to the water content in PEO-H2O samples. On the other hand, DSC measurements give the result that PEO-H2O-HQ systems can be considered as homogeneous so long as the content of H2O and/or HQ is not so high. Furthermore, the water molecules in the system exist as bound water. Results of high-frequency spectroscopic measurements for the PEO-H2O and PEO-H2O-HQ systems show good agreement with those of DSC and NMR measurements.     

On-line monitoring of all-acrylic emulsion polymerization reactors by Raman spectroscopy

Fourier Transform Raman spectroscopy was used as an on-line sensor in order to monitor high solids content (50 wt%) n-BA/MMA emulsion copolymerization reactions. Due to the similarity of the chemical structure of the monomers, no separate bands could be detected for each monomer, and therefore a multivariate calibration technique was required (Partial Least Squares Regression, PLSR). Using experimental data from several semi-batch reactions independent PLSR models were built for the solids content, cumulative copolymer composition and unreacted amounts of n-BA and MMA. Those models were experimentally validated by monitoring reactions not used for calibration. It is demonstrated that FT-Raman spectroscopy can be successfully applied to on-line monitor emulsion polymerization reactors. This technique also shows a high potential for process control purposes because independent information about several molecular properties can be obtained from a single apparatus.     

Dielectric properties of a single nanochannel investigated by high-frequency impedance spectroscopy

High-frequency electric impedance spectroscopy is used to characterize the dielectric properties of a single nanochannel in a micro/nanofluidic device. The simulated electric impedance results lead to the determination of two conductance regimes, a non-ideal capacitance and its surface charge.     

Monitoring powder blending by NIR spectroscopy

A strategy is proposed for the monitoring of powder blending. Samples are taken throughout the blender vessel and scanned by diffuse reflectance spectroscopy in the NIR range. The NIR spectra are first subjected to the Standard Normal Variate transformation (SNV). The first approach consists of overlaying the transformed spectra taken from different locations at each time. To quantify the differences between the spectra, the standard deviation spectrum at each time is calculated and the mean standard deviation value is plotted as a function of time. This plot indicates the time at which the blend is most homogeneous. Each individual spectrum can be compared with the mixture spectrum, which is an approximation of the spectrum of a true homogeneous sample. For that purpose several approaches, i.e. determination of the dissimilarity, Principal Component Analysis, are proposed. As an alternative approach to monitoring the blending the use of SIMPLISMA is recommended.Dedicated to Professor Dr. h.c. mult. J.F.K. Huber on the occasion of his 70th birthday     

Evaluation of emulsion stability by thermogravimetric analysis (tg)

A rapid and simplified method for the determination of phase inversion temperature (PIT) and the stability of oil in water emulsions, stabilized by nonionic emulsifiers, is described. The method is based on the use of any thermogravimetric apparatus from which the rate of loss of water can be measured as a function of linear increase in the emulsion temperature. A DTG peak is obtained at the PIT: the emulsion in which the lowest PIT is observed is also the less stable one.     

Maximum stability of a single spherical particle attached to an emulsion drop

The stability of a single, solid, spherical particle attached to a liquid drop in an emulsion is discussed. Ignoring effects due to gravity and line tension, we calculate the energies required to either detach the particle from the drop or to engulf the particle within the drop. The stability of the attached particle is here defined as the smaller of these two energies. A simple formula is derived for the value of Young's angle which gives maximum stability for a given radius ratio of particle to detached drop. For maximum stability the particle should be preferentially wetted by the liquid forming the drop.     

Monitoring of phenol photodegradation by ultraviolet spectroscopy

Advanced oxidation processes (AOPs) have been developed as an emerging technology for hazardous organic treatment in industrial wastewater. In this paper, the contribution of ultraviolet (UV) spectroscopy to follow phenol photodegradation was studied in a laboratory photochemical reactor equipped with a low pressure mercury lamp. It has been observed that a multicomponent approach is efficient for the evolution estimation of the initial product or intermediate compounds formed during the photodegradation.     

Ostwald ripening and the stability of emulsion systems: an explanation for the effect of an added third component

The destabilizing effect of Ostwald ripening has been considered in relation to O/W hexane emulsions stabilized by sodium dodecyl sulfate. The addition of a third component to the oil phase gives rise to stability provided it has a lower vapor pressure than the oil itself. The stabilizing effects of small quantities of hexadecane and perfluorochemical oils are discussed with reference to the Kelvin effect and Raoult's law.     

Emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. V. Effect of reaction conditions on the stability of polytetrafluoroethylene latex

The stability of PTFE latex prepared in the absence of emulsifier by radiation-induced polymerization was investigated by electrophoresis and conductometric titration. The storage stability depends on total dose rather than dose rate, and the stable latex can be obtained in the region log D > 0.026 V₁ ? 0.6, where D is the total dose (10⁴ rad) and V₁ is a polymer concentration in latex (g/liter). The stability increases only during polymerization in the presence of enough TFE monomer. The ζ potential of the latex particles lies in the region from ?25 to ?50 mV in an as-polymerized state (near pH 3) and from ?50 to ?65 mV at pH 10. The number of carboxyl end groups and surface charge density were examined by conductometric titration with NaOH and calculation from the G values of radiolysis of water. All the surface charge densities measured by conductometric titration are larger than those calculated from the G values. These results suggest that some acids have been formed on the surface of the particles. The acids may be the carboxyl end groups of polymer chains or hydrofluoric acid (HF) adsorbed on the surface. PTFE particles prepared in this polymerization system are stabilized mainly due to the carboxyl end groups and adsorptions of OH? and HF on the particles.     

Dehydration efficiency of high-frequency pulsed DC electrical fields on water-in-oil emulsion

The influence of several operational variables on the electrostatic separation of water-in-oil emulsions is investigated in a Perspex cell equipped with a high-frequency pulsed DC generator using conductivity technique. The ascending and the descending periods of the observed conductivity vs. time curves were fit to the sigmoid and power function, respectively, which revealed the model parameters that were used to quantify dehydration efficiency (DE). Experiment results show that DE increases with decreasing inter-electrode distance, and at a given inter-electrode distance, DE increases with decreasing frequency. Furthermore, at a given pulse interval, DE increases with increasing pulse duration.     

Water pH and surfactant addition effects on the stability of an Algerian crude oil emulsion

In many oil production sites water injection is used as a piston to push the crude out of the well. As the age of the field progresses, the ratio of water to oil produced increases. Agitation of a water and crude oil mixture may give stable water-in-oil emulsion in which the water remains dispersed for a long period of time. These emulsions can cause severe problems in production and transport processes since they normally possess high stability and viscosity. The most important water properties which may contribute to the emulsion stability include pH and additive content. In this study, we report on the effect of both, water pH and the presence of surfactant molecules (anionic, cationic or non-ionic) on the stability of an Algerian crude oil (Haoudh el Hamra well) aqueous emulsion prepared by a mechanical agitation procedure. The stability was followed by the test-bottle method to measure the resolved water separated from the emulsion, and optical microscopy to visualize the dispersed water droplets in the oil phase. The results of the effects of varying the aqueous-phase pH suggest that the neutral medium is more efficient than acidic or basic environment for stabilizing the emulsions. The addition of non-ionic surfactants has a better potential to improve crude oil emulsion stability with respect to both cationic and anionic surfactants which do not show any improvement in the oil/water phase compatibility.     

Monitoring the electrochemistry of single molecules by surface-enhanced Raman spectroscopy

Coherent control of chemical species in complex systems is always subject to intrinsic inhomogeneities from the environment. For example, slight chemical modifications can decisively affect transport properties of molecules on surfaces. Hence, single-molecule (SM) studies are the best solution to avoid these problems and to study diverse phenomena in biology, physics, and chemistry. Along these lines, monitoring SM redox processes has always been a "holy grail" in electrochemistry. To date, claims of SM electrochemistry by spectroscopy have come only from fluorescence quenching of polymers and redox-fluorescent molecules. In unconnected developments, the potential of the bianalyte surface-enhanced Raman scattering (SERS) method as a technique with SM sensitivity has been demonstrated. Raman spectroscopy has the potential to explore SM detection of any molecule, independent of its chemical nature. We provide definitive proof of SM events following redox cycles using SERS. The superior sensitivity and spectral richness of SERS makes it general enough to study, in principle, SM electron transfer of any (label-free) molecule.     

Monitoring PDT by means of superficial reflectance spectroscopy

Monitoring of relevant parameters during photodynamic therapy (PDT) and correlating these with treatment response is necessary to guarantee optimal and reproducible treatment outcome. In this paper we study the correlation between changes in the local tissue optical properties (absorption and scattering coefficients) during ALA-PDT and changes in PpIX fluorescence. The optical properties are measured extremely superficially by employing a single fiber for the delivery and collection of white light to and from the tissue. The measured reflectance spectrum is modeled in terms of four relevant parameters: blood saturation, relative blood volume fraction, scattering intensity and wavelength dependence of the scattering. All these parameters, except the relative blood volume fraction, are shown to correlate with the rate of photobleaching of PpIX, which in turn has previously been shown to correlate with the response of tissues to PDT. These results yield valuable insight in the behavior of these parameters during PDT and their suitability to predict PDT-response for other photosensitizers for which monitoring through photobleaching is not possible.     

Monitoring of liquid-phase organic reactions by photoelectron spectroscopy

There are strings attached: after linking the reacting groups to head groups of ionic liquids to drastically lower the vapour pressures of the reactants, ordinary liquid-phase organic reactions can be monitored by in situ X-ray photoelectron spectroscopy. This approach is demonstrated for the nucleophilic substitution of an alkyl amine and an alkyl chloride moiety, which are attached to the cation and anion of ionic liquids, respectively.     

Formation and stability of paraffin oil-in-water nano-emulsions prepared by the emulsion inversion point method

Paraffin oil-in-water nano-emulsions stabilized by Tween 80/Span 80 were prepared using the emulsion inversion point method at different emulsification temperatures. Nano-emulsions with droplet size below 200 nm were formed above a critical surfactant-to-oil ratio of 0.20 at 50 degrees C. The main destabilization mechanism of the systems was found to be Ostwald ripening. An interesting phenomenon was that the Ostwald ripening rate declined as the surfactant concentration rose. Furthermore, flocculation was also found to contribute to the instability of the nano-emulsions, especially for those with low surfactant concentrations. Study on the electrophoretic properties of emulsion droplets revealed a negative value of the zeta potential, which was strongly dependent on the pH of the systems.     

Monitoring sealed automotive lead-acid batteries by sparse-impedance spectroscopy

A reliable diagnostics of lead-acid batteries would become mandatory with the induction of an improved power net and the increase of electrically assisted features in future automobiles. Sparse-impedance spectroscopic technique described in this paper estimates the internal resistance of sealed automotive lead-acid batteries in the frequency range 10 Hz-10 kHz, usually produced by the alternators fitted in the automobiles. The state-of-health of the battery could be monitored from its internal resistance. Dedicated to Professor C N R Rao on his 70th birthday     

Monitoring of the smoking process by multicommutation Fourier transform infrared spectroscopy

Nicotine was selected as the target molecule for monitoring of the smoking process by multicommutation Fourier Transform Infrared spectroscopy (FTIR). The method involved the use of CHCl₃ for on-line extraction of nicotine from tobacco, cigarette filters and tobacco ash from NH₄OH alkalinized samples, and absorbance measurement of the characteristic band at 1316 cm⁻¹ in the stopped-flow mode, by obtaining the peak area in the range between 1334 and 1300 cm⁻¹. Under the best operational conditions, the procedure developed provided a detection limit of 0.05 mg mL⁻¹ nicotine, corresponding to 0.5 mg g⁻¹ in the solid sample, a relative standard deviation less than 2.5%, and a sampling frequency of 12 determinations h⁻¹. It can be concluded that nicotine migrates in the smoke mainstream towards the filter during the smoking process. The smoking of cigarettes and cigars is different. Nicotine is retained weakly by both tobacco and filter in the case of cigarettes, and strongly by the unburned tobacco in cigars. The incomplete smoking of cigars and cigarettes reduces nicotine intake and thus reduces the additive effect.