Preparation and Characterization of Porous Titania by Modified Sol-Gel Method

Mesoporous titania, especially anatase, is attractive due to its potential applications. A novel method to control pore structure of titania, surfactant- or polymer modification, is proposed. The wet gels and gel films, prepared from Ti(O-nC₄H₉)₄ were dried at 90°C and annealed at 500°C after immersion in surfactant or polymer solutions, and mesoporous anatase was obtained. The pore size, pore volume and specific surface area of the surfactant-modified bulk gels, estimated from N₂ absorption-desorption curves, are more than twice larger than those of the gels without modification. The pore size of the surfactant-modified gel films, observed by SEM, are similar to that of the bulk gels. The pore size obviously depended on the size of micelles. The pore size of the gels modified with hydrophilic polymers hardly increased, but the pore volume and the specific surface area increased.     

Growth mechanism of Nb-doped TiO<Subscript>2</Subscript> sol–gel multilayer films characterized by SEM and focus/defocus TEM

TiO₂ and Nb-doped TiO₂ films were prepared by sol–gel processing, their microstructure was adjusted by varying the number of subsequent coating-firing cycles that resulted in final total film thickness of ~100 nm. When only few subsequent coatings are stacked (large single layer thickness) granular polycrystalline microstructures are observed. Doping with Nb reduces the crystallite size compared to the respective pure anatase films. When the single layer thickness is reduced, the film growth is successively dominated by the nucleation of subsequent films on the underlying crystalline material resulting in a columnar dense film structure. The multilayer architecture of such films can be demonstrated by defocus TEM imaging even if crystalline columns exceed single film boundaries. Results indicate that Nb is homogeneously incorporated into the anatase lattice by substitution of Ti, nevertheless the electric conductivity after H₂ post annealing is significantly lower than reported for analogous films prepared by magneton sputtering or pulsed laser deposition.     

Study on the Superhydrophilicity of the SiO2-TiO2 Thin Films Prepared by Sol-Gel Method at Room Temperature

Nanoscale SiO₂-TiO₂ composite thin films with the thickness of about 100 nm were prepared by sol-gel method at room temperature in air. The chemical states of the elements on the surface and near the surface were measured by XPS. The results showed that the Ti on/near the surface of the thin films existed not only as TiO₂ but also as Ti₂O₃. Part of the TiO₂ was changed to Ti₂O₃ after UV irradiation. The crystalline structure of the TiO₂ in the SiO₂-TiO₂ thin films was anatase with the crystallite size of 14–20 nm. It was found that the thin film prepared at room temperature in air has good superhydrophilic property and has strong adherence to the substrate.     

Superhydrophobic polymer‐particle composite films produced using various particle sizes

Hydrophilic alumina (Al₂O₃) nanoparticles (25, 35, and 150 nm) are dispersed in different concentrations in solutions of a commercial hydrophobic poly(alkyl siloxane) (Silres BS‐290), and the suspensions are sprayed on glass surfaces. Static contact angles (θ_S), measured on surfaces of siloxane‐nanoparticle composite films that were prepared from dilute dispersions, increase rapidly with particle concentration. Composite films prepared from concentrated dispersions exhibit a maximum, constant θ_S (at saturation θ_S is 160°), which is not affected by the size of the particles. These films exhibit also very small contact angle hysteresis (5°), which is also independent of the particle size. Consequently, the same superhydrophobic character can be induced in siloxane films using nanoparticles, which can range from a few up to several tenths of nanometers. However, the particle size and more precisely the particle specific surface area affects dramatically the minimum critical particle concentration, which must be used in the dispersions to induce superhydrophobicity on the surface of the composite films, that is, to achieve θ_S = 150°. It is shown that critical particle concentration decreases exponentially with specific surface area. This result can be important for manufacturers of superhydrophobic surfaces who are interested in having a good control on the wettability of the composite films. Copyright © 2012 John Wiley & Sons, Ltd.     

Sensor Performance of Nanostructured TiO<Subscript>2</Subscript>–SnO<Subscript>2</Subscript> Films Prepared by an Aqueous Sol–Gel Process

Nanostructured TiO₂–SnO₂ thin films and powders were prepared by a facile aqueous particulate sol–gel route. The prepared sols showed a narrow particle size distribution with hydrodynamic diameter in the range 17.2–19.3 nm. Moreover, the sols were stable over 5 months, since the constant zeta potential was measured during this period. The effect of Sn:Ti molar ratio was studied on the crystallisation behaviour of the products. X-ray diffraction analysis revealed that the powders were crystallised at the low temperature of 400 °C containing anatase-TiO₂, rutile-TiO₂ and cassiterite-SnO₂ phases, depending on annealing temperature and Sn:Ti molar ratio. Furthermore, it was found that SnO₂ retarded the anatase to rutile transformation up to 800 °C. The activation energy of crystallite growth was calculated in the range 0.96–6.87 kJ/mol. Transmission electron microscope image showed that one of the smallest crystallite sizes was obtained for TiO₂–SnO₂ binary mixed oxide, being 3 nm at 600 °C. Field emission scanning electron microscope analysis revealed that the deposited thin films had nanostructured morphology with the average grain size in the range 20–40 nm at 600 °C. Thin films produced under optimized conditions showed excellent microstructural properties for gas sensing applications. They exhibited a remarkable response towards low concentrations of CO gas at low operating temperature of 200 °C, resulting in increased thermal stability of sensing films as well as a decrease in their power consumption.     

总气压与Ar/O2流量比对直流对向靶磁控溅射TiO2薄膜光催化性能的影响

采用对向靶磁控溅射法在不同气压和Ar/O₂流量比条件下, 以氟化SnO₂ (FTO)导电玻璃为基底制备了多晶TiO₂薄膜. 台阶仪测量结果显示所制备TiO₂薄膜的平均厚度约为200 nm. 随着溅射气压的升高, TiO₂薄膜由锐钛矿与金红石混晶结构转变为纯锐钛矿结构. 分别采用场发射扫描电镜(FESEM)和原子力显微镜(AFM)分析了不同气压和Ar/O₂流量比对TiO₂薄膜表面形貌的影响, 结果显示TiO₂薄膜的表面粗糙度随溅射总气压和Ar/O₂流量比的增加而增大. 以初始浓度为100×10^-6 (体积分数)的异丙醇(IPA)气体为目标物检测所制备TiO₂薄膜的光催化性能, 并分析该气相光催化反应的机理, 在紫外照射条件下异丙醇先氧化为丙酮再被氧化为CO₂.当总溅射气压为2.0 Pa、Ar/O₂流量比为1:1时, 溅射所得TiO₂薄膜具备最优光催化活性并可在IPA降解反应中保持较高的催化活性和稳定性.     

A study on the effect of starting material phase on the production of trititanate nanotubes

Mixed phase TiO₂ powders of different composition and particle size were subjected to the hydrothermal reaction with 10 M NaOH. It was found that the anatase phase component of the starting material is easily converted to trititanate nanotubes at 140 °C. At this temperature the rutile phase remains unreacted, however at 170 °C it reacts to form trititanate plates and belts. When the reaction time is increased to 7 days, all the TiO₂ is converted to trititanate and the morphology is exclusively nanoplates and belts, with the tube phase destroyed. Many researchers have observed some heterogeneity in their reaction products, but have mainly focussed on the nanotubes. We observed that the tubes are only prepared from the anatase phase component of a TiO₂ precursor, whereas the rutile component produces trititanate plates and sheets, irrespective of the reaction length. The particle size affects the rate of reaction, resulting in the phase transition being more easily visible in the reactions starting with the larger TiO₂ particle size.     

Effect of synthesis conditions on the preparation of titanium dioxides from peroxotitanate solution and their photocatalytic activity

Nanosized TiO₂ particles were prepared by the hydrothermal method from the amorphous powders which were precipitated in an aqueous peroxotitanate solution. The physical properties of the nanosized TiO₂ particles prepared were investigated. We also examined the activity of TiO₂ particles as a photocatalyst on the decomposition of orange II. The titania sol can be successfully crystallized to the anatase phase through hydrothermal aging at temperatures higher than 160°C. The particle size increases from 18 to 26 nm as the synthesis temperature increases from 140 to 200°C. Titania particles prepared at 180°C show the highest activity, and titania particles calcined at 400°C show also the highest activity on the photocatalytic decomposition of orange II.     

Synthesis of TiO<Subscript>2</Subscript> nano powder by the sol-gel method and its use as a photocatalyst

In this work the titanium dioxide powder was prepared by the optimized and simple Sol-Gel method and then characterized. The gelling pH was set to values of 3 (TiO₂-A), 7 (TiO₂-N) and 9 (TiO₂-B) to observe the effect on the properties of the material. In these three cases nanoparticulated materials were obtained with particle sizes between 10nm and 20nm. The larger surface areas were obtained at pH 3, which is several times larger than the others. Furthermore, with the gelling condition pH 3, it was possible to synthesize pure anatase phase titania. Some preliminary results on the test of the photocatalytic activity of the synthesized materials in the reduction of nitric oxide are presented. Based on these results the nanoparticle TiO2, which was prepared in acidic pH 3 with the pure anatase phase and the lowest particle size has the highest reactivity for the photocatalytic reduction of nitric oxide.     

Formation of Anatase Nanocrystals in Sol-Gel Derived TiO2-SiO2 Thin Films with Hot Water Treatment

We have successfully prepared transparent and porous anatase nanocrystals-dispersed films by treating the sol-gel derived TiO₂-SiO₂ films containing poly(ethylene glycol), PEG, with hot water. This process was done at temperatures lower than 100°C under atmospheric pressure, and thus anatase nanocrystals-dispersed films can be formed on various kinds of substrates including organic polymers with poor heat resistance. The changes in structure and composition of the TiO₂-SiO₂ gel films with hot water treatment were related to the formation process of anatase nanocrystals in the TiO₂-SiO₂ gel films with hot water treatment. The formation of anatase nanocrystals was found to proceed to hydrolysis of Si–O–Ti bonds and dissolution of SiO₂ component. In addition, porous film structure formed by leaching of PEG with hot water treatment led to homogenous dispersion of anatase nonocrystals in the films.     

The influence of titanium dioxide phase composition on dyes photocatalysis

A comparative study of TiO₂ powders prepared by sol–gel methods is presented. Titanium tetraisopropoxide was used as the precursor for the sol–gel processes. The effects of the annealing treatment on phase, crystallite size, porosity and photodegradation of dyes (methyl orange and methylene blue) were studied. The phase structure, microstructure and surface properties of the films were characterized by using X-ray diffraction (XRD) and Atomic Force Microscopy (AFM). The X-ray diffraction was used for crystal phase identification, for the accurate estimation of the anatase–rutile ratio and for the crystallite size evaluation of each polymorph in the samples. It was found that the only TiO₂ anatase phase of the synthesized TiO₂ develops below 500 °C, between 600 and 800 °C the anatase coexist with rutile and above 800 °C only the rutile phase was found in the samples. Attention has been paid not only to crystal structures, but also to the porosity, the particle size and the photocatalytic properties. However, the annealing temperature was found to have significant influence on the photocatalytic properties. Different TiO₂ doctor blade thin films were obtained mixing the sol gel powder (100% anatase) and TiO₂ Aldrich with TiO₂ Degussa P25. The surfactant (Triton X100 or sodium dodecyl sulfate) affects the packing density of the particles during deposition and the photocatalytic degradation efficiency of the dyes. The photocatalytic degradation kinetics of methyl orange and methylene blue using TiO₂ thin film were investigated.     

Effect of annealing temperatures and of high content of the iron ion (Fe<Superscript>3+</Superscript>)-doping on transition anatase–rutile phase of nanocrystalline TiO<Subscript>2</Subscript> thin films prepared by sol–gel spin coating

Titanium dioxide doped with iron (III) was prepared by sol–gel Spin Coating method. The phase structures, morphologies, particle size of the doped TiO₂ have been characterized by X-ray diffraction (XRD), Raman spectroscopy, atomic force microscopy (AFM) and ultraviolet–visible (UV–Vis) spectrophotometer. The XRD and Raman results show that the 10% Fe³⁺-doped TiO₂ thin films crystallize in anatase phase between 600 and 800 °C, and into the anatase–rutile phase at 1,000 °C, and further into the rutile phase when the content of Fe³⁺ increases (20%). The grain size calculated from XRD patterns shows that the crystallinity of the obtained anatase particles increased from 39.4 to 43.4 nm as the temperature of annealing increase, whereas the size of rutile crystallites increases, with increasing Fe³⁺ concentrations from 36.9 to 38.1 nm. The AFM surface morphology results confirmed that the particle size increases by increasing the annealing temperature and also with an increasing of Fe³⁺ content. The optical band gap (E _g) of the films was determined by the UV–Vis spectrophotometer. We have found that the optical band gap decreased with an increasing of annealing temperatures and also with an increasing of Fe³⁺ content.     

The effect of heat treatment in the reducing atmosphere on the physical properties of TiO2 thin films prepared by sol–gel method

Multilayered nanostructured TiO₂ thin films were prepared by sol–gel and dipping deposition on quartz substrate followed by thermal treatment under reducing atmosphere (20 %H₂–80 %Ar). Heat treatment at progressively higher temperatures caused structural, morphological, and optical changes, which were investigated by X-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy, and UV–Vis spectroscopy. The conductivities of the thin films were also measured by 4-point probe method. The XRD results showed that the calcined TiO₂ thin films consist of single anatase phase which was completely transformed into rutile phase after heat treatment at 1,000 °C. The grains of films grew by intra-agglomerate densification after heat treatment at higher temperatures. The root mean square roughness of the samples was found to be in the range of 0.58–3.36 nm. The partially reduced TiO₂ samples have red-shifted transmittance bands due to new energy band formed by oxygen vacancies. The electrical conductivity of the films was also enhanced after heat treatment in reducing atmosphere.     

ZnO纳米薄膜的制备及其气敏性质研究

纳米氧化锌薄膜具有光电、压电、压敏和气敏等多种性质,使其在透明导体、发光元件、太阳能电池窗口、光波导器、单色场发射显示器、高频压电转换器、微传感器等方面具有广泛的用途.     

Preparation of Porous Titania Film by Modified Sol-Gel Method and its Application to Photocatalyst

Sol-Gel derived mesoporous titania films with controlled pore sizes were prepared by surfactant templating. The coating sol was obtained by hydrolysis of Ti(OC₄H₉)₄ in ethanol/HCl solution. The gel films, prepared by spin coating on glass substrate, were dried after immersion in surfactant solutions under an atmospheric pressure. The porous films of anatase with columnar and rectangular structure were obtained after annealing at 500°C. The annealed films are transparent and 80–140 nm in thickness. Refractive indices of the films with surfactant immersion were 10–20% lower than those of the films without immersion. The spacing between the columns or rectangular grains and the grain shape were found to depend on the surfactant species. The pohoto-catalytic activity of the films for the oxidation of NO _x was improved by the surfactant modification.     

Preparation and characterization of transparent TiO2 thin films coated on fused-silica substrates

The transparent TiO₂ thin films coated on fused-SiO₂ substrates were prepared by the sol–gel method and spin-coating technique. Effects of calcination temperature on crystal structure, grain size, surface texture, and light transmittance of the films were investigated. After calcining at 600–1,200 °C, the thicknesses of the TiO₂ films were all around 80 nm and the molecular structures of the films were anatase, even at 1,200 °C. The calcined TiO₂ films had the ultraviolet light (wavelength 200–400 nm) transmittances of ≤29% and the visible light (wavelength 400–800 nm) transmittance of ≥72%. By photocatalytically decomposing the methylene blue (MB) in water, the photocatalytic activities of the TiO₂ thin films were measured and represented using the characteristic time constant (τ) for the MB degradation. While the films prepared at 1,000 and 1,200 °C photodecomposed about 54 mol% of the MB in water (the corresponding τ ≈ 14.8 h) after exposing to 365-nm UV light for 12 h, the films prepared at 600 and 800 °C had smaller τ (≈9.0 h) and photodecomposed about 74 mol% of the MB in water at the same testing conditions.     

溶胶法制备的二氧化硅与二氧化钛复合薄膜的性能

在室温下, 采用溶胶法在玻璃基板上制备了厚度约为100 nm的均匀、透明的纳米SiO2-TiO2复合薄膜.研究了不同温度处理后薄膜的超亲水性、光催化能力等光致活性.通过XPS对薄膜表面及近表面元素的化学态的研究发现, Ti在表面及近表面不仅以Ti4＋形式存在, 也存在少量Ti3＋.紫外光照射后, 部分Ti4＋ 转变成了Ti3＋. XRD研究表明, 该薄膜中的TiO2主要以锐钛矿形式存在, 而且其晶粒大小为14～20 nm.用AFM研究了SiO2-TiO2薄膜的表面形貌及不同的温度处理对TiO2颗粒大小的影响.     

Antibacteria and Detoxification Function of Polystyrene/TiO2 Nanocomposites

The composites of TiO₂ nanoparticles (anatase structure, average particle size 20–30 nm) as inorganic particle additive in the polystyrene (PS) were prepared by co‐rotating twin screw extruder. The structure and morphology of the composites were determined by scanning electron microscope (SEM), transmission electron microscopy (TEM) and x‐ray diffraction (XRD). Titanium (Ti) element distribution on the surface of PS/TiO₂ master batch was measured by energydispersive x‐ray microanalysis system. The mechanical properties such as tensile strength and Charpy impact strength were tested and revealed that reached the maximum value when the content of TiO₂ nanoparticles is at 1.0 wt%. The composites possess excellent antibacterial and detoxification effect on the familiar bacillus. The antibacteria efficiency of the composites is more than 99% and its detoxification efficiency on the bacterial endotoxin is more than 90%.     

Preparation and Characterization of Peroxo Titanic Acid Solution Using TiCl3

The peroxo titanic acid solution was successfully prepared using titanium trichloride as a precursor. The basic properties of the TiO₂ film prepared by the solution were investigated in view of phase change, bandgap energy, crystalline size etc. The film displayed amorphous TiO₂ at room temperature, anatase above 281°C and a mixture of anatase and rutile at 990°C. The crystalline size increases with annealing temperatures, while the bandgap energies decrease due to the quantum size effect and the formation of rutile phase which has low bandgap energy. As a result of TG-DTA, it was found that annealing treatment at 990°C for 2 h formed a mixture of anatase and rutile through three steps: (1) the removal of physically adsorbed water (2) the decomposition of peroxo group (3) amorphous-anatase or anatase-rutile phase transformation.     

Study of the slow electrolyte-induced changes in the TiO<Subscript>2</Subscript> hydrosol structure

Slow changes in the TiO₂ hydrosol structure induced by a small KCl additive were studied using the small-angle X-ray scattering. The initial sol of anisometric anatase nanocrystals stabilized by HCl was prepared. After addition of KCl scattering curves were measured regularly for 2 years. It was established the formation and the accumulation of small dense aggregates. A model of the slow structural changes in the TiO₂ sols with electrolyte additives comprising the two steps of aggregation was proposed. At first the larger anatase nanocrystals combine slowly forming the small dense aggregates through the oriented attachment mechanism. Then, at the critical size of such aggregates, they coagulate quickly forming the looser particles.