Certification of trace and major elements and methylmercury concentrations in a macroalgae (Fucus sp.) reference material, IAEA-140

A marine reference material, IAEA-140, prepared with a macroalgae (Fucus sp.) was recently produced by the International Atomic Energy Agency and certified for trace and major elements and for methylmercury (MeHg). Certification of this material was achieved as an outcome of an international analytical intercomparison study which resulted in 116 independent sets of results reported by participants from 54 countries. The statistical evaluation of the collected data and the criteria used for assignment of the mean and uncertainty values are described. The analysis of data allowed to certify concentration values for 24 elements and MeHg, and to provide information values for another 10 elements. Regarding the elements which could be given certified values, between two and eight different instrumental methods were used to measure metal concentrations, and four independent analytical procedures were used to measure MeHg concentrations. In order to assess the results of the certification procedure, a comparison was made between the certified values obtained from the world-wide intercomparison results and the values obtained from a small subgroup of well-qualified laboratories. The means and 95% confidence intervals for reference values obtained by the two methods are similar for most elements showing that the usual method of certification used by the IAEA, based on large groups of participants, is indeed pertinent.     

Certification of trace and major elements and methylmercury concentrations in a macroalgae (Fucus sp.) reference material, IAEA-140

A marine reference material, IAEA-140, prepared with a macroalgae (Fucus sp.) was recently produced by the International Atomic Energy Agency and certified for trace and major elements and for methylmercury (MeHg). Certification of this material was achieved as an outcome of an international analytical intercomparison study which resulted in 116 independent sets of results reported by participants from 54 countries. The statistical evaluation of the collected data and the criteria used for assignment of the mean and uncertainty values are described. The analysis of data allowed to certify concentration values for 24 elements and MeHg, and to provide information values for another 10 elements. Regarding the elements which could be given certified values, between two and eight different instrumental methods were used to measure metal concentrations, and four independent analytical procedures were used to measure MeHg concentrations. In order to assess the results of the certification procedure, a comparison was made between the certified values obtained from the world-wide intercomparison results and the values obtained from a small subgroup of well-qualified laboratories. The means and 95% confidence intervals for reference values obtained by the two methods are similar for most elements showing that the usual method of certification used by the IAEA, based on large groups of participants, is indeed pertinent.     

Characterization of NIES CRM No. 23 Tea Leaves II for the determination of multielements

A candidate environmental certified reference material (CRM) for the determination of multielements in tea leaves and materials of similar matrix, NIES CRM No. 23 Tea Leaves II, has been developed and characterized by the National Institute for Environmental Studies (NIES), Japan. The origin of the material was tea leaves, which were ground, sieved through a 106-μm mesh, homogenized, and then subdivided into amber glass bottles. The results of homogeneity and stability tests indicated that the material was sufficiently homogeneous and stable for use as a reference material. The property values of the material were statistically determined based on chemical analyses by a network of laboratories using a wide range of methods. Sixteen laboratories participated in the characterization, and nine certified values and five reference values were obtained. These property values of the candidate CRM, which are expressed as mass fractions, were close to the median and/or mean values of the mass fractions of elements in various tea products. The candidate CRM is appropriate for use in analytical quality control and in the evaluation of methods used in the analysis of tea and materials of similar matrix.     

Laser Ablation Inductively Coupled Plasma Mass Spectrometry for Determination of Trace Elements in Geological Glasses

 Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was used as a powerful multielement analytical method for trace analysis of geological glasses which are useful as reference materials for geochemical in-situ microanalytical work. The quantification of the analytical results was carried out using the BCR-2G and NIST 612 glass standard reference material (SRM). The experimentally determined relative sensitivity coefficients (RSC) for both SRMs vary between 0.2 and 3 for most of the elements, with increasing mass an increasing of relative sensitivity coefficients was observed. The relative standard deviation (RSD) for determination of trace element concentration of most elements (N=3) are between 2 and 10%. The determination of trace elements in various geological glasses by LA-ICP-MS yielded a good agreement with the reference values and those results of other trace analytical methods. Received October 15, 1999. Revision April 14, 2000.     

Development and certification of the new SRM 695 trace elements in multi-nutrient fertilizer

During the past seven years, several states within the US have enacted regulations that limit the amounts of selected non-nutritive elements in fertilizers. Internationally, several countries, including Japan, China, and Australia, and the European Union also limit the amount of selected elements in fertilizers. The elements of interest include As, Cd, Co, Cr, Cu, Hg, Mo, Ni, Pb, Se, and Zn. Fertilizer manufacturers and state regulatory authorities, faced with meeting and verifying these limits, need to develop analytical methods for determination of the elements of concern and to validate results obtained using these methods. Until now, there were no certified reference materials available with certified mass fraction values for all elements of interest in a blended, multi-nutrient fertilizer matrix. A new standard reference material (SRM) 695 trace elements in multi-nutrient fertilizer, has been developed to help meet these needs. SRM 695 has recently been issued with certified mass fraction values for seventeen elements, reference values for an additional five elements, and information values for two elements. The certificate of analysis includes an addendum listing percentage recovery for eight of these elements, determined using an acid-extraction inductively-coupled plasma optical-emission spectrometry (ICP–OES) method recently developed and tested by members of the Association of American Plant Food Control Officials.     

电感耦合等离子体光谱/质谱联机同时测定多金属结核中常量、微量、痕量元素

采用电感耦合等离子体质谱(ICP-MS)与等离子体光谱(ICP-OES)联机同时测定多金属结核样品中常量、微量、痕量元素。样品经高压密封溶样弹消解后,一次气动雾化进样,ICP-OES测定常量和微量元素,ICP-MS测定微量和痕量元素。详细探讨了不同浓度范围元素的测定方式、元素分析信号的采集模式、多原子离子干扰的校正因子。采用ICP-MS与ICP-OES二种方式同时测定Co、Cu、Ni、Zn、V、Ba、Sr,分析结果表明具有较好的一致性。所建立的ICP-MS与ICP-OES联机检测技术用于多金属结核标准样品的分析(Nod-A-1,GSPN-1,GSPN-2,GSPN-3),分析结果与推荐值符合,相对标准偏差小于10％。     

Examination of steel samples, provided as reference materials, by instrumental analyses

Summary Seven steel samples considered as reference materials have been analysed by atomic emission spectrometry with inductively coupled plasma (ICP-AES), atomic absorption spectrometry with flame and graphite furnace atomization (FAAS, GFAAS), differential pulse anodic stripping voltammetry (DPASV), X-ray fluorescence analysis with total reflection sample carrier (TXRF), and instrumental neutron activation analysis (INAA). Totally, 18 elements were determined. Over 90% of all results were in good agreement with the values determined by wet analytical methods. The deviations can be explained by systematical errors for special elements in distinct methods and by statistical errors, mainly at very low concentrations because some elements, in the low ng/g region, are not homogeneously distributed in the given material.formerly: Amt für Standardisierung, Meßwesen und Warenprüfung, Große Steinernetischstrasse 4, DDR-3010 Magdeburg     

Comparison of NAA and ICP-MS for the determination of major and trace elements in environmental sample

Summary Major and trace elements in soil and plant samples, including standard reference materials were determined by means of neutron activation analysis (NAA) and inductively coupled plasma-mass spectrometry (ICP-MS). The analytical procedure for NAA utilized dried powder samples. The concentration of iodine in soil samples was determined by radiochemical NAA. The irradiated samples were cooled and then counted with a Ge gamma-ray detector connected to a multi-channel analyzer. For ICP-MS analysis, the samples were decomposed by microwave digestion with an acid mixture. The concentration of I in the soil samples was measured by ICP-MS after separation by ignition. The analytical values for most elements in the environmental samples by both methods were in good agreement, whereas sample treatments were different. Measured value of Zr in the soil samples by ICP-MS was about 50% lower than that by NAA. It should be assumed that some minerals of Zr in soil particles were not entirely dissolved by the acid mixture. Analytical results of Cd for three different Cd levels in unpolished rice flour samples (NIES 10-a, b and c) determined by ICP-MS were in agreement with certified values. The concentration of Cd in the sample with the lowest Cd level, as determined by NAA with 57% counting error, was 3 times higher than the certified value.     

Characterization of a suite of ginkgo-containing standard reference materials

A suite of three ginkgo-containing dietary supplement Standard Reference Materials (SRMs) has been issued by the National Institute of Standards and Technology (NIST) with certified values for flavonoid aglycones, ginkgolides, bilobalide, and selected toxic trace elements. The materials represent a range of matrices (i.e., plant, extract, and finished product) that provide different analytical challenges. The constituents have been determined by at least two independent analytical methods with measurements performed by NIST and at least one collaborating laboratory. The methods utilized different extractions, chromatographic separations, modes of detection, and approaches to quantitation. The SRMs are primarily intended for method validation and for use as control materials to support the analysis of dietary supplements and related botanical materials. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Comparison of three analytical methods for the determination of trace elements in whole blood

Three different analytical techniques were compared in a study of the role of trace elements in multiple sclerosis. Data for eight elements (Cd, Co, Cr, Cu, Mg, Mn, Pb, Zn) from neutron activation, flame atomic absorption and electrothermal atomic absorption methods were compared and evaluated statistically. No difference (probability less than 0.001) was observed in the elemental values obtained. Comparison of data between suitably different analytical methods gives increased confidence in the results obtained and is of particular value when standard reference materials are not available.     

Determination of trace elements in zeolites by laser ablation ICP-MS

Laser ablation inductively coupled plasma mass spectrometry using a quadrupole-based mass spectrometer (LA-ICP-QMS) was applied for the analysis of powdered zeolites (microporous aluminosilicates) used for clean-up procedures. For the quantitative determination of trace element concentrations three geological reference materials, granite NIM-G, lujavrite NIM-L and syenite NIM-S, from the National Institute for Metallurgy (South Africa) with a matrix composition corresponding to the zeolites were employed. Both the zeolites and reference materials were fused with a lithium borate mixture to increase the homogeneity and to eliminate mineralogical effects. In order to compare two different approaches for the quantification of analytical results in LA-ICP-MS relative sensitivity coefficients (RSCs) of chemical elements and calibration curves were measured using the geostandards. The experimentally obtained RSCs are in the range of 0.2-6 for all elements of interest. Calibration curves for trace elements were measured without and with Li or Ti as internal standard element. With a few exceptions the regression coefficients of the calibration curves are better than 0.993 with internal standardization. NIM-G granite reference material was employed to evaluate the accuracy of the technique. Therefore, the measured concentrations were corrected with RSCs which were determined using lujavrite reference material NIM-L. This quantification method provided analytical results with deviations of 1-11% from the recommended and proposed values in granite reference material NIM-G, except for Co, Cs, La and Tb. The relative standard deviation (RSD) of the determination of the trace element concentration (n = 5) is about 1% to 6% using Ti as internal standard element. Detection limits of LA-ICP-QMS in the lower microg/g range (from 0.03 microg/g for Lu, Ta and Th to 7.3 microg/g for Cu, with the exception of La) have been achieved for all elements of interest. Under the laser ablation conditions employed (lambda: 266 nm, repetition frequency: 10 Hz, pulse energy: 10 mJ, laser power density: 6 x 10(9) W/cm2) fractionation effects of the determined elements relative to the internal standard element Ti were not observed.     

Interlaboratory study to improve the quality of trace element determinations in rainwater

This is the first publication which describes the development of a reference material (RM) for the determination of 11 trace elements (Cu, Pb, Mn, Ni, Zn, Fe, Cd, Co, V, As and Al) in rainwater at microgram per liter concentrations. An interlaboratory comparison study for the determination of trace elements in rainwater was carried out for material performance studies to establish analyte concentrations with a stated uncertainty. Fifteen reputed laboratories from Asia, Europe and North America participated in the study. These laboratories used their regular in-house methods to analyze the rainwater samples. The aim of this study is to establish concentration levels of trace elements in rainwater based on interlaboratory study results. Details of the production, homogeneity and stability of the reference sample are given in this article. The organization of the study and the quality assurance measures undertaken at the organizer's laboratory are described. The analytical results obtained from individual laboratories and the analytical methods used for the determination of trace elements in rainwater are discussed. Based on the results obtained from the intercomparison study, certified values as well as informative values are assigned to the 11 trace elements in rainwater.     

The comparison of the results of two independent intercomparison studies (BAK-1 and SLB-1) from the same bulk material of a lateritic soil

Summary A comparison of the results for major, minor and trace elements from the BAK-1 intercomparison study [1] and that of SLB-1 [2] are presented. These two independent studies were based on the same bulk material of a lateritic bauxite (soil) from Suriname but different preparation and homgeneity testing schemes were employed. The values for Al₂O₃, Fe₂O₃, TiO₂ and LOI were not significantly different while the SiO₂ value determined by the SLB-1 intercomparison run was 1.88%±0.34% in respect to 3.93%±2.65% from the BAK-1 study. An attempt to explain this difference in the SiO₂ values was made on the basis of the sample preparation and the participating analytical laboratories. Finally, provisional values and uncercainty limits for major elements and LOI are presented for SLB-1 reference material.     

Characterization of a wheat flour reference material (ARC/CL) for twelve elements

Summary An ARC/CL coded wheat flour reference material (ARC/CL RM) with established recommended concentration values for 12 elements [1,2] was further characterized for P, K and Cr contents by means of an intercomparison study. Minor corrections were made to earlier recommended values in accordance with new results obtained. Fifteen laboratories using a total of 11 methods based on six entirely different analytical principles participated in the intercomparison study. The medians and standard deviations were calculated for the results of the intercomparison study. After rejecting as outliers values falling outside the median ± sd, the present recommended values were obtained by recalculating the median and 95% confidence limits. Recommended values were established for the major elements Ca, K, Mg, P, the minor elements Cu, Fe, Mn, Zn, and the trace elements Mo, Cr, Ni and Se. The relative standard deviations for the 95% confidence limits of the medians were lower than 10% for major and minor elements, 11% for Mo and 18% for Cr. All of the recommended concentration values fell into category A, having a high degree of confidence. The present RM, with its 16 recommended concentrations, is of value for use in nutritional, food composition and contaminant monitoring studies.     

Quantification of heavy metals for the recycling of waste plastics from electrotechnical applications

Analytical data on element concentrations in plastics is an important prerequisite for the recycling of technical waste plastics. The chemical resistance and high additive contents of such materials place a high demand on analytical methods for quantifying elements in thermoplastics from electrotechnical applications. The applicability of three common independent analytical methods (EDXRF, AAS, ICP-AES) for the quantification of heavy metals in such technical waste plastics of varying composition was studied. Following specific sample pre-treatments, such as closed vessel microwave assisted digestion and wet ashing with H(2)SO(4), three hazardous metals (Pb, Cd, Sb) were determined. Conditions were investigated to minimize matrix effects for all analytical techniques employed. The trueness for the quantification of Cd was checked by using the certified reference material VDA 001-004 (40-400 mug g(-1) Cd in polyethylene), and no significant differences to certified values were found. The best detection limits were found to be 2, 1.3 and 7.9 mug g(-1) for Cd, Pb and Sb, respectively. In technical waste polymers, Sb was detected to be in the range 1-7%, Cd in the range 80-12 000 mug g(-1) and Pb in the range 90-700 mug g(-1). The precision reached for the analysis of this complex material, is comparable for all methods, and can be expressed by a relative standard deviation smaller than 8%. Application of multivariate analysis of variances (MANOVA) showed no differences between the mean results, except for the ICP-AES analysis following wet ashing with H(2)SO(4).     

同位素稀释-液相色谱-串联质谱法在小麦粉细交链孢菌酮酸和腾毒素标准物质制备和定值中的应用

建立了小麦粉中细交链孢菌酮酸（TeA）和腾毒素（TEN）标准物质的研制和定值方法,为开展粮食中交链孢霉毒素基体标准物质的研制提供重要方法学借鉴。该标准物质样品为天然污染交链孢霉毒素的小麦籽粒,定值目标物为TeA和TEN,采用同位素稀释-液相色谱-串联质谱法（ID-LC-MS/MS）进行定值测量,多个实验室合作定值。所研制的标准物质具有常温避光保存、定值不确定度小等特点。该标准物质是目前国际上唯一一种天然污染TeA和TEN的小麦粉标准物质,可用于食品安全风险监测、产品质量检测等领域相关分析方法的评价和测量质量控制等。     

Analytical strategy for the chemical characterization of biological reference materials

The analytical strategy for the elemental chemical characterization of biological reference materials followed during a recently completed Reference Material development endeavour is discussed. Characterization, the assignment of reliable values to total elemental concentrations of a wide range of elements, poses the most difficult challenge in the scheme of reference material (RM) production. A review is presented of the many factors considered that significantly impinged on the conduct and outcome of the complex analytical characterization exercise. Major considerations were: (1) analytical elemental characterization philosophy, (2) analyte selection, (3) selection of analytical methodologies, (4) statistical protocols, (5) in-house characterization, (6) assessment of material homogeneity (7) cooperative interlaboratory characterization campaign, (8) data evaluation and (9) calculation of concentration values and associated uncertainties.Contribution no. 94-47 from Centre for Land and Biological Resources Research     

Prompt gamma-ray analysis (PGA) of meteorite samples, with emphasis on the determination of Si

Neutron-induced prompt gamma-ray analysis (PGA) was applied to seven meteorite samples (Allende, Zagami, Acfer 209, ALH77005, ALH84001, EET79001 and Neagari). Samples were irradiated in both the thermal neutron and the cold neutron guided beams of JRR-3M at JAERI. Multiple samples of an Allende standard powder were analyzed for Si using two different methods: (1) the comparison method, using a Si standard, and (2) the mono-standard method, using Fe as an internal reference element. The Si concentrations determined by these two methods are in good agreement with literature values. The analytical sensitivity for Si using the cold neutron guided beam is∼14.3× higher than that for the thermal neutron guided beam. Other elements determined (B, Ca, Ti and S) also showed higher sensitivities using the cold neutron beam. The other meteorites studied showed some anomalous B and S values likely due to the effects of terrestrial weathering/contamination.     

Certification for trace elements and methyl mercury mass fractions in IAEA-452 scallop (Pecten Maximus) sample

A marine certified reference material (CRM), IAEA-452, prepared with scallop (Pecten maximus) sample was recently produced by the International Atomic Energy Agency (IAEA) and certified for trace elements and methyl mercury (MeHg). The Scallop (Pecten maximus) sample is commonly found and consumed seafood and is also used as bio-indicators for trace metal contamination in marine pollution studies. This paper presents the sample preparation methodology, material homogeneity and stability studies, evaluation of certification campaign results, the assignment of property values and their associated uncertainty. The reference values and associated expanded uncertainty for 9 trace elements (As, Cd, Cr, Cu, Fe, Hg, Mn, Pb and Zn) and MeHg in scallop sample are established. The informative value for one more element (Ni) is also given. The new CRM can be used for the development and validation of analytical methods for determination of trace elements and methyl mercury in seafood and also for quality assurance/quality control purposes.     

Development of a certified reference material (NMIJ CRM 7505-a) for the determination of trace elements in tea leaves

A certified reference material (CRM) for trace elements in tea leaves has been developed in National Metrology Institute of Japan (NMIJ). The CRM was provided as a dry powder (<90 μm) after frozen pulverization of washed and dried fresh tea leaves from a tea plant farm in Shizuoka Prefecture, Japan. Characterization of the property value for each element was carried out exclusively by NMIJ with at least two independent analytical methods, including inductively coupled plasma mass spectrometry (ICP-MS), high-resolution (HR-) ICP-MS, isotope-dilution (ID-) ICP-MS, inductively coupled plasma optical emission spectrometry (ICP-OES), graphite-furnace atomic-absorption spectrometry (GF-AAS) and flame atomic-absorption spectrometry (FAAS). Property values were provided for 19 elements (Ca, K, Mg, P, Al, B, Ba, Cd, Cu, Fe, Li, Mn, Na, Ni, Pb, Rb, Sr, Zn and Co) and informative values for 18 elements (Ti, V, Cr, Y, and all of the lanthanides, except for Pm whose isotopes are exclusively radioactive). The concentration ranges of property values and informative values were from 1.59% (mass) of K to 0.0139 mg kg(-1) of Cd and from 0.6 mg kg(-1) of Ti to 0.0014 mg kg(-1) of Lu, respectively. Combined relatively standard uncertainties of the property values were estimated by considering the uncertainties of the homogeneity, analytical methods, characterization, calibration standard, and dry-mass correction factor. The range of the relative combined standard uncertainties was from 1.5% of Mg and K to 4.1% of Cd.