Synthesis and characterization of multiblock copolymers based on hydrophilic disulfonated poly(arylene ether sulfone) and hydrophobic partially fluorinated poly(arylene ether ketone) for fuel cell applications

Sulfonated fluorinated multiblock copolymers based on high performance polymers were synthesized and evaluated for use as proton exchange membranes (PEMs). The multiblock copolymers consist of fully disulfonated poly(arylene ether sulfone) and partially fluorinated poly(arylene ether ketone) as hydrophilic and hydrophobic segments, respectively. Synthesis of the multiblock copolymers was achieved by a condensation coupling reaction between controlled molecular weight hydrophilic and hydrophobic oligomers. The coupling reaction could be conducted at relatively low temperatures (e.g., 105 °C) by utilizing highly reactive hexafluorobenzene (HFB) as a linkage group. The low coupling reaction temperature could prevent a possible trans‐etherification, which can randomize the hydrophilic‐hydrophobic sequences. Tough ductile membranes were prepared by solution casting and their membrane properties were evaluated. With similar ion exchange capacities (IECs), proton conductivity and water uptake were strongly influenced by the hydrophilic and hydrophobic block sequence lengths. Conductivity and water uptake increased with increasing block length by developing nanophase separated morphologies. Atomic force microscopy (AFM) and transmission electron microscopy (TEM) experiments revealed that the connectivity of the hydrophilic segments was enhanced by increasing the block length. The systematic synthesis and characterization of the copolymers are reported. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 214–222, 2010     

Highly sulfonated multiblock copoly(ether sulfone)s for fuel cell membranes

Highly sulfonated multiblock copoly(ether sulfone)s applicable to proton electrolyte fuel cells (PEFCs) were synthesized by the coupling reaction of corresponding hydroxyl‐ terminated oligomers in the presence of highly reactive decafluorobiphenyl (DFB) as a chain extender, followed by postsulfonation with concentrated sulfuric acid. Their molecular weights were reasonably high as determined by viscosity measurement (η_inh = 0.72–1.58 dL/g). It was also confirmed that postsulfonation selectively took place in hydrophilic segments to yield highly sulfonated multiblock copolymers (IEC = 1.90–2.75 mequiv/g). The resulting polymers gave transparent, flexible, and tough membranes by solution casting. The 4b membrane, as a representative sample, demonstrated good mechanical strength in the dry state regardless of high IEC value (2.75 mequiv/g). The 4a–c membranes with higher IEC values (IEC = 2.75–2.79 mequiv/g) maintained high water uptake (13.7–17.7 wt %) at 50% RH and it was still high (7.4–8.5 wt %) at 30% RH. Proton conductivity of all membranes at 80 °C and 95% RH was higher than that of Nafion 117. Furthermore, the 4a membrane showed high proton conductivity, comparable with Nafion 117 in the range of 50–95% RH, and maintained high proton conductivity (2.3 × 10^?3 S/cm) even at 30% RH. Finally, the surface morphology of the membrane was investigated by tapping mode atomic force microscopy, which showed well‐connected hydrophilic domains that could work as proton transportation channel. This phase separation and the high water uptake behavior probably contributed to high and effective proton conduction in a wide range of relative humidity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2757–2764, 2010     

Synthesis and properties of multiblock copoly(arylene ether)s containing superacid groups for fuel cell membranes

A series of block copoly(arylene ether)s containing pendant superacid groups were synthesized, and their properties were investigated for fuel cell applications. Two series of telechelic oligomers, iodo‐substituted oligo(arylene ether ketone)s and oligo(arylene ether sulfone)s, were synthesized. The degree of oligomerization and the end groups were controlled by changing the feed ratio of the monomers. The nucleophilic substitution polymerization of the two oligomers provided iodo‐substituted precursor block copolymers. The iodo groups were converted to perfluorosulfonic acid groups via the Ullmann coupling reaction. The high degree of perfluorosulfonation (up to 83%) was achieved by optimizing the reaction conditions. Tough and bendable membranes were prepared by solution casting. The ionomer membranes exhibited characteristic hydrophilic/hydrophobic phase separation with large hydrophilic clusters (ca. 10 nm), which were different from that of our previous random copolymers with similar molecular structure. The block copolymer structure was found to be effective in improving the proton‐conducting behavior of the superacid‐modified poly(arylene ether) ionomer membranes without increasing the ion exchange capacity (IEC). The highest proton conductivity was 0.13 S/cm at 80 °C, 90% relative humidity, for the block copolymer ionomer membrane with IEC = 1.29 mequiv/g. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of multiblock partially fluorinated hydrophobic poly(arylene ether sulfone)‐hydrophilic disulfonated poly(arylene ether sulfone) copolymers for proton exchange membranes

Hydrophobic‐hydrophilic sequence multiblock copolymers, based on alternating segments of phenoxide terminated fully disulfonated poly(arylene ether sulfone) (BPS100) and fluorine‐terminated poly(arylene ether sulfone) (6FBPS0) were synthesized and evaluated for application as proton exchange membranes. By utilizing mild reaction conditions the ether–ether interchange reactions were minimized, preventing the randomization of the multiblock copolymers. Tough, ductile, transparent membranes were solution cast from the block copolymers and were characterized with regard to intrinsic viscosity, morphology, water uptake, and proton conductivity. The conductivity values of the 6FBPS0‐BPSH100 membranes were compared to Nafion 212 and a partially fluorinated sulfonated poly(arylene ether sulfone) random copolymer (6F40BP60). The nanophase separated morphology was confirmed by transmission electron microscopy and small angle X‐ray scattering, and enhanced proton conductivity at reduced relative humidity was observed with longer block lengths. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of partially fluorinated poly(arylene ether sulfone) multiblock copolymers bearing perfluorosulfonic functions

Partially fluorinated poly(arylene ether sulfone) multiblock copolymers bearing perfluorosulfonic functions (ps‐PES‐FPES), with ionic exchange capacity (IEC) ranging between 0.9 and 1.5 meq H⁺/g, are synthesized by regioselective bromination of partially fluorinated poly(arylene ether sulfone) multiblock copolymers (PES‐FPES), followed by Ullman coupling reaction with lithium 1,1,2,2‐tetrafluoro‐2‐(1,1,2,2‐tetrafluoro‐2‐iodoethoxy)ethanesulfonate. The PES‐FPES are prepared by aromatic nucleophilic substitution reaction by an original approach, that is, “one pot two reactions synthesis.” The chemical structures of polymers are analyzed by ¹H and ¹⁹F NMR spectroscopy. The resulted ionomers present two distinct glass transitions and α relaxations revealing phase separation between the hydrophilic and the hydrophobic domains. The phase separation is observed at much lower block lengths of ps‐PES‐FPES as compared with the literature. AFM and SANS observations supported the phase separation, the hydrophilic domains are well dispersed but the connectivity to each other depends on the ps‐PES block lengths. The thermomechanical behavior, the water up‐take, and the conductivity of the ps‐PES‐FPES membranes are compared with those of Nafion 117^® and randomly functionalized polysulfone (ps‐PES). Conductivities close or higher to those of Nafion 117^® are obtained. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1941–1956     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Synthesis and characterization of postsulfonated poly(arylene ether sulfone) diblock copolymers for proton exchange membranes

Sulfonated poly(arylene ether sulfone) diblock copolymers were studied through the postsulfonation process. Two kinds of hydrophobic oligomers with a molecular weight of 20 kDa were prepared in advance as block sequences and then coupled together to obtain diblock copolymers. One oligomer was synthesized from bis(4‐hydroxyphenyl) sulfone (BHPS) and 4,4′‐difluorodiphenyl sulfone (DFDPS), which was thought to be incapable of postsulfonation. The other oligomer was synthesized from hydroquinone (HQ) and 4,4′‐dichlorodiphenyl sulfone (DCDPS), which successfully proceeded to a hydrophilic sequence as a result of sulfonation onto the HQ moiety after the coupling reaction. Consequently, a diblock copolymer with high molecular weight was obtained; although its intrinsic viscosity was too low to form a tough membrane because of its high rigidity and high crystallinity. Therefore, the use of decafluorobiphenyl (10F) as a termination reagent was investigated with the aim of achieving higher coupling reactivity and a kinky property. As a result, a sulfonated diblock copolymer was successfully obtained with sufficient molecular weight and intrinsic viscosity to form the membrane, as well as with adequate thermal properties. It was observed that proton conductivity, water uptake, and the water diffusion coefficient increased with higher ion exchange capacity. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 700–712, 2009     

Copoly(arylene ether nitrile) and copoly(arylene ether sulfone) ionomers with pendant sulfobenzoyl groups for proton conducting fuel cell membranes

Three series of fully aromatic ionomers with naphthalene moieties and pendant sulfobenzoyl side chains were prepared via K₂CO₃ mediated nucleophilic aromatic substitution reactions. The first series consisted of poly(arylene ether)s prepared by polycondensations of 2,6‐difluoro‐2′‐sulfobenzophenone (DFSBP) and 2,6‐dihydroxynaphthalene or 2,7‐dihydroxynaphthalene (2,7‐DHN). In the second series, copoly(arylene ether nitrile)s with different ion‐exchange capacities (IECs) were prepared by polycondensations of DFSBP, 2,6‐difluorobenzonitrile (DFBN), and 2,7‐DHN. In the third series, bis(4‐fluorophenyl)sulfone was used instead of DFBN to prepare copoly(arylene ether sulfone)s. Thus, all the ionomers had sulfonic acid units placed in stable positions close to the electron withdrawing ketone link of the side chains. Mechanically strong proton‐exchange membranes with IECs between 1.1 and 2.3 meq g⁻¹ were cast from dimethylsulfoxide solutions. High thermal stability was indicted by high degradation temperatures between 266 and 287 °C (1 °C min⁻¹ under air) and high glass transition temperatures between 245 and 306 °C, depending on the IEC. The copolymer membranes reached proton conductivities of 0.3 S cm⁻¹ under fully humidified conditions. At IECs above ∼1.6 meq g⁻¹, the copolymer membranes reached higher proton conductivities than Nafion^® in the range between −20 and 120 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and properties of sulfonated poly(arylene ether)s containing azole groups

Random and multiblock sulfonated poly(arylene ether sulfone)s (SPEs) containing various azole groups such as oxadiazole and triazole were synthesized and characterized for fuel cell application. Successful preparation of SPE membranes depended on the structure of azole groups, which affected solubility of precursors and the resulting SPEs. Although oxadiazole groups were incorporated into hydrophobic component, they were found to be hydrophilic to give higher proton conductivity. Introduction of oxadiazole groups into random SPE gave comparable proton conductivity to that of Nafion NRE at >60% relative humidity at 80 °C. Block copolymer structure further increased the proton diffusion coefficient without increasing ion exchange capacity. Hydrolytic and oxidative stability of the SPE membranes was affected by both hydrophilic and hydrophobic components. Oxadiazole groups gave negative impact on hydrolytic and mechanical stability to the SPE membranes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Isomeric effect of sulfonated poly(arylene ether)s comprising dihydroxynaphthalene on properties for polymer electrolyte membranes

Polymer electrolyte membranes (PEMs) made of sulfonated poly(arylene ether)s consisted of 3,3′‐disulfo‐4,4′‐dichlorodiphenylsulfone disodium salt, 2,6‐dichlorobenzonitrile, and one of three dihydroxynaphthalene isomers (2,6‐, 2,7‐, and 1,5‐dihydroxynaphthalene, abbreviated as 2,6‐N, 2,7‐N, and 1,5‐N, respectively) were prepared with similar level of inherent viscosity and ion exchange capacity, and structural effect of the catenation in dihydroxynaphthalene isomers on membrane properties was compared. In the case of membranes for PEM fuel cell application with relatively high ion exchange capacity around 2.1 mequiv/g, three copolymers showed almost the same proton conductivity; however, swelling in water increased with the following order: 1,5‐N < 2,6‐N < 2,7N. In the case of direct methanol fuel cell membranes with lower ion exchange capacity around 1.5 mequiv/g, no remarkable difference in proton conductivity was also observed in three isomeric copolymers and swelling property and methanol permeability were lower in 1,5‐N and 2,6‐N copolymers than 2,7‐N copolymer. These tendencies show that higher rigidity or energy barrier for conformational change of polymer chain gives better performance of PEM for fuel cells with superior dimensional stability. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Segmented sulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers for proton exchange membrane fuel cells. I. Copolymer synthesis and fundamental properties

Segmented disulfonated poly(arylene ether sulfone)‐b‐polyimide copolymers based on hydrophilic and hydrophobic oligomers were synthesized and evaluated for use as proton exchange membranes (PEMs). Amine terminated sulfonated poly (arylene ether sulfone) hydrophilic oligomers and anhydride terminated naphthalene based polyimide hydrophobic oligomers were synthesized via step growth polymerization including high temperature one‐pot imidization. Synthesis of the multiblock copolymers was achieved by an imidization coupling reaction of hydrophilic and hydrophobic oligomers oligomers in a m‐cresol/NMP mixed solvent system, producing high molecular weight tough and ductile membranes. Proton conductivities and water uptake increased with increasing ion exchange capacities (IECs) of the copolymers as expected. The morphologies of the multiblock copolymers were investigated by tapping mode atomic force microscopy (TM‐AFM) and their measurements revealed that the multiblock copolymers had well‐defined nano‐phase separated morphologies which were clearly a function of block lengths. Hydrolytic stability test at 80 °C water for 1000 h showed that multiblock copolymer membranes retained intrinsic viscosities of about 80% of the original values and maintained flexibility which was much improved over polyimide random copolymers. The synthesis and fundamental properties of the multiblock copolymers are reported here and the systematic fuel cell properties will be provided in a separate article. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4879–4890, 2007     

Synthesis and characterization of alt‐copoly(carbosiloxane)s containing oligodiphenylsiloxane segments

Novel α,ω‐divinyloligodiphenylsiloxanes (1,9‐divinyldecaphenylpentasiloxane, 1,7‐divinyloctaphenyltetrasiloxane, 1,5‐divinylhexaphenyltrisiloxane, and 1,3‐divinyltetraphenyldisiloxane) were prepared and copolymerized by Pt‐catalyzed hydrosilylation with α,ω‐dihydridopentasiloxanes. The molecular weights of the copolymers were measured with gel permeation chromatography, and their thermal properties were characterized with differential scanning calorimetry and thermogravimetric analysis. The polymers had high thermal stability in air and nitrogen. The oligomer and polymer structures were determined with ¹H, ¹³C, ¹⁹F, and ²⁹Si NMR and IR spectrometry. The molecular weights of the oligomers were measured with high‐resolution mass spectrometry. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2155–2163, 2005     

Ionomers for proton exchange membrane fuel cells by sulfonation of novel dendritic multiblock copoly(ether‐sulfone)s

The synthesis and properties of the first examples of dendritic multiblock co PES s, bearing sulfonated dendritic clusters, that form strong membranes are described. End‐capped dendritic multiblock co PES s with various average block lengths (n = 50–80) were synthesized by two‐step reactions. The synthesis of dendritic blocks consisting of difunctional dendritic block and monofunctional dendritic end‐group was accomplished by an aromatic nucleophilic substitution reaction of hexakis(4‐(4‐fluorophenylsulfonyl)phenyl)benzene with varying amounts of 1‐(4‐hydroxyphenyl)‐2,3,4,5,6‐pentaphenylbenzene, which provides a number of pendant phenyl rings as postsulfonation sites. Polycondensation of a controlled molar ratio between 4,4′‐dihydroxybenzophenone and bis(4‐fluorophenyl)sulfone monomers was carried out in the presence of the difunctional and monofunctional dendritic blocks in sulfolane at 215 °C for 3.5 h. Essentially six sulfonic acid groups were introduced into each hexaphenylbenzene moiety on the dendritic blocks by reaction with a large excess of chlorosulfonic acid, followed by hydrolysis with KOH aqueous solution. The introduction of longer average blocks (n = 60–80) into the dendritic PES s improved the mechanical properties of the resulting sulfonated dendritic PES membranes. At a level of IEC (0.92–1.26 meq/g) similar to Nafion (0.91 meq/g), PES membranes showed proton conductivities (58–67 mS/cm) comparable with that of Nafion (99 mS/cm). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5461–5473, 2009     

Sulfonated multiblock copoly(ether sulfone)s as membrane materials for fuel cell applications

Arylene ether multiblock copolymers of the (AB)_n-type with various degrees of sulfonation have been prepared by a two-step polycondensation procedure. Multiblock copolymers in high yields and of high molecular weights were obtained. For comparison random copolymers with the same overall composition were synthesized. The theoretical ion-exchange capacities (IEC) of the materials were ranging from 0.50 mmol/g to 1.25 mmol/g. The water-uptake of the multiblock copolymers showed a linear dependency from the IEC and was increasing with increasing IEC. No differences were observed between random and block copolymers. Furthermore, the hydrolytic stability of aromatic sulfonic acid groups was investigated in this study. Aromatic sulfonic acids, having additional electron donating groups, especially in ortho- or para-position to the sulfonic acid group are sensitive to hydrolytic desulfonation. On the other hand electron-withdrawing groups in meta-position showed a stabilizing effect.     

Morphological investigations of block sulfonated poly(arylene ether ketone) copolymers as potential proton exchange membranes

A series of block sulfonated poly(arylene ether ketone) (SPAEK) copolymers with different block lengths and ionic contents were synthesized by a two‐stage process. The morphology of these block SPAEK copolymers was investigated by various methods, such as differential scanning calorimetry (DSC), transmission electron microscope (TEM), and small angle X‐ray scattering (SAXS). Dark colored ionic domains of hundreds of nanometers spreading as a cloud‐like belt were observed in TEM images. The sizes of the ionic domains as a function of block copolymer composition were determined from SAXS curves. The results for the evolution of ionic domains revealed that the block copolymers exhibited more clearly phase‐separated microstructure with increasing ionic contents and hydrophobic sequence lengths. Proton conductivity is closely related to the microstructure, especially the presence of large interconnected ionic domains or ionic channels. Block SPAEK membranes have interconnected ionic clusters to provide continuous hydrophilic channels, resulting in higher proton conductivity. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and characterization of partially disulfonated hydroquinone‐based poly(arylene ether sulfone)s random copolymers for application as proton exchange membranes

Partially disulfonated hydroquinone (HQ)‐based poly(arylene ether sulfone) random copolymers were synthesized and characterized for application as proton exchange membranes. The copolymer composition was varied in the degree of disulfonation. The copolymers were characterized by ¹H NMR, Differential Scanning Calorimetry (DSC), and other analytical techniques. The copolymer with a 25% degree of disulfonation showed the best balance between water uptake and proton conductivity. The copolymers showed substantially reduced methanol permeability compared with Nafion® and satisfactory direct methanol fuel cell performance. The methanol selectivity improved significantly in comparison to Nafion® 117. At a given ionic composition, the HQ‐based system showed higher water uptake and proton conductivity than the biphenol‐based (BPSH‐xx) poly(arylene ether sulfone)s copolymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 384–391, 2009     

Mechanical and morphological studies of sulfonated poly(arylene ether sulfone)s for potential application in fuel cell membrane

Two groups of synthesized sulfonated poly(ether sulfone)s with similar structures but different size of repeat units were selected. Investigation of the properties of these copolymers with different sulfonation contents for application as fuel cell membrane was the main aim of this study. These groups of copolymers showed different thermal behavior, mechanical properties, dimensional and oxidative stability, ion exchange capacity, water uptake, and proton conductivity. Structure–property relation was surveyed, and the copolymers showed acceptable results for use as fuel cell membrane. The swelling ratio of the copolymers was in the range of 3.3–6.6%, and the proton conductivity of them was about 0.020–0.077 S/cm at 25°C. These data were comparable with Nafion 115 with 8.15% of swelling ratio and 0.085 S/cm of proton conductivity. Copyright © 2017 John Wiley & Sons, Ltd.     

Controlled sulfonation of poly(arylene ether sulfone)s and poly(arylene ether ketone)s with different molecular structures for polymer electrolyte membranes

Poly(arylene ether sulfone) copolymers derived from 9,9-bis(4-hydroxyphenyl)fluorene, bisphenol S and 4,4′-difluorodiphenylsulfone and poly(arylene ether ketone) copolymers derived from 4-phenoxybiphenyl, diphenyl ether and isophthaloyl chloride were prepared as precursor polymers for sulfonation reaction in which sulfonic groups are introduced quantitatively into specified positions. Sulfonation reaction for these two series of copolymers by concentrated sulfuric acid was successfully carried out to give sulfonated polymers with controlled positions and degree of sulfonation. Thermal stability, moisture absorption and proton conductivity for these two series of copolymers were measured and the results were compared to those of perfluorosulfonic acid polymers.     

Synthesis of highly sulfonated poly(arylene ether sulfone) random (statistical) copolymers via direct polymerization

Novel biphenol‐based wholly aromatic poly (arylene ether sulfones) containing pendant sulfonate groups were prepared by direct aromatic nucleophilic substitution polycondensation of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenyl sulfone (SDCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS) and biphenol. Copolymerization proceeded quantitatively to high molecular weight in N‐methyl‐2‐pyrrolidinone at 190°C in the presence of anhydrous potassium carbonate. Tough membranes were successfully cast from the control and the copolymers, which had a SDCDPS/DCDPS mole ratio of either 40:60 or 60:40 using N,N‐dimethylactamide; the 100% SDCDPS homopolymer was water soluble. Short‐term aging (30 min) indicates that the desired acid form membranes are stable to 220°C in air and conductivity values at 25°C of 0.110 (40%) and 0.170 S/cm (60%) were measured, which are comparable to or higher than the state‐of‐the art fluorinated copolymer Nafion 1135 control. The new copolymers, which contain ion conductivity sites on deactivated rings, are candidates as new polymeric electrolyte materials for proton exchange membrane (PEM) fuel cells. Further research comparing their membrane behavior to post‐sulfonated systems is in progress.     

Influence of adjusted hydrophilic–hydrophobic lengths in sulfonated multiblock copoly(ether sulfone) membranes for fuel cell application

Sulfonated multiblock copoly(ether sulfone)s applicable to proton exchange membrane fuel cells (PEMFCs) were synthesized by the coupling reaction of the hydroxyl‐terminated hydrophilic and hydrophobic oligomers with different lengths in the presence of highly reactive decafluorobiphenyl (DFB) as a chain extender to investigate the influence of each length on the membranes' properties, such as water uptake, proton conductivity, and morphology. Multiblock copolymers with high molecular weights (M_n > 50,000, M_w > 150,000) were obtained under mild reaction conditions. The resulting membranes demonstrated good oxidative stability for hot Fenton's reagent and maintained high water uptake (7.3–18.7 wt %) under a low relative humidity (50% RH). Proton conductivity of all membranes at 80 °C and 95% RH was higher than that of Nafion 117 membrane, and good proton conductivity of 7.0 × 10^?3 S/cm was obtained at 80 °C and 50% RH by optimizing the oligomer lengths. The surface morphology of the membranes was investigated by tapping mode atomic force microscopy (AFM), which showed that the multiblock copolymer membranes had a clearer surface hydrophilic/hydrophobic‐separated structure than that of the random copolymer, and contributed to good and effective proton conduction. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7332–7341, 2008