Nanosegregated polymeric domains on the surface of Fe3O4@SiO2 particles

Multifunctional, biocompatible, and brush‐grafted poly(ethylene glycol)/poly(ε‐caprolactone) (PEG/PCL) nanoparticles have been synthesized, characterized, and used as vehicles for transporting hydrophobic substances in water. For anchoring the polymer mixed brushes, we used magnetic‐silica particles of 40 nm diameter produced by the reverse microemulsion method. The surface of the silica particle was functionalized with biocompatible polymer brushes, which were synthesized by the combination of “grafting to” and “grafting from” techniques. PEG was immobilized on the particles surface, by “grafting to,” whereas PCL was growth by ROP using the “grafting from” approach. By varying the synthetic conditions, it was possible to control the amount of PCL anchored on the surface of the nanoparticles and consequently the PEG/PCL ratio, which is a vital parameter connected with the arrangement of the polymer brushes as well as the hydrophobic/hydrophilic balance of the particles. Thus, adjusting the PEG/PCL ratio, it was possible to obtain a system formed by PEG and PCL chains grafted on the particle's surface that collapsed in segregated domains depending on the solvent used. For instance, the nanoparticles are colloidally stable in water due to the PEG domains and at the same time are able to transport, entrapped within the PCL portion, highly water‐insoluble drugs. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2966–2975     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Comparison of flow and batch polymerization processes for production of vinyl ether terpolymers for use in the delivery of siRNA

Synthetic polymers represent a modifiable class of materials that can serve as adjuvants to address challenges in numerous biomedical and medicinal chemistry applications including the delivery of siRNA. Polymer‐based therapeutics offer unique challenges in both synthesis and characterization as compared to small molecule therapeutics. The ability to control the structure of the polymer is critical in creating a therapeutic. Reported herein, are batch and flow polymerization processes to produce amphiphilic terpolymers through a Lewis acid BF₃OEt₂‐catalyzed polymerization. These processes focus on controlling reaction variables, which affect polymer structure in this rapid, exothermic, nonliving cationic polymerization. In addition to analytical characterization of the polymers, the in vivo activity of the polymer‐siRNA conjugates is also highlighted—demonstrating that the method of synthesis does affect the in vivo activity of the resulting polymer conjugate. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1119–1129     

Efficient synthesis of well‐defined amphiphilic cylindrical brushes polymer with high grafting density: Interfacial “Click” chemistry approach

Reported here is a novel approach toward efficient preparation of well‐defined cylindrical brushes polymer (CBPs) with both hydrophobic and hydrophilic side chains connected to the linear backbone by interfacial “click” chemistry in two immiscible solvents. The CBPs with high grafting density of more than 95% and molecular polydispersity (M_w/M_n) less than 1.12 can be readily synthesized using present approach. On contrary, the CBPs synthesized from the “click” reaction in a single solvent in homogenous state have low grafting density of less than 55% and molecular polydispersity (M_w/M_n) more than 1.78. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Efficient Cu(I) acetate‐catalyzed cycloaddition of multifunctional alkynes and azides: From solution to bulk polymerization

“Click” chemistry is an effective and commonly used technique in polymer chemistry for the synthesis and modification of polymers. In this study, the bulk polymerization of multifunctional alkynes and azides was achieved by the copper(I)‐catalyzed alkyne–azide 1,3‐dipolar cycloaddition. The influence of different catalyst systems on the polymerization kinetics of the “click”reaction were evaluated by differential scanning calorimetry. Surprisingly, Cu(I) acetate showed the most efficient catalytic behavior among the applied Cu(I) salts. The polymerization kinetics in solution were investigated by 1H NMR spectroscopy and size exclusion chromatography. According to the 1H NMR investigation the copper(I)‐catalyzed cycloaddition follows a second‐order kinetics with external catalysis. Additionally, the mechanical properties of the resulting polymers were investigated by depth sensing indentation. Thereby the polymerizations of the alkyne tripropargylamine with the azides 1,3‐bis(azidomethyl)benzene and 1,4‐bis(azidomethyl)benzene resulted in mechanical hard materials. Furthermore, the combination of the alkynes tripropargylamine and di(prop‐2‐yn‐1‐yl) isophorone dicarbamate and polymerization with 1,2‐bis(2‐azidoethoxy)ethane resulted in high indentation moduli. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 239–247     

Facile preparation of superhydrophobic and oleophobic surfaces via the combination of Cu(0)‐mediated reversible‐deactivation radical polymerization and click chemistry

The fabrication of novel hydrophobic, superhydrophobic, and oleophobic surfaces on glass using nanosilica particles modified with polymer brushes prepared via surface initiated Cu(0)‐mediated reversible‐deactivation radical polymerization was demonstrated. Monomers including n‐butyl acrylate, 2,2,2‐trifluoroethyl methacrylate, and 1,1,1,3,3,3‐hexafluoroisopropyl acrylate were used to synthesize a series of nanosilica–polymer organic/inorganic hybrid materials. Products were analyzed using infrared spectroscopy, thermogravimetric analysis, scanning and transmission electron microscopy. The coated nanosilica showed core–shell structures that contains polymer brushes up to 67 wt %. The application of these particles for modifying surface wettability was examined by covalently attaching them to glass via a recently developed one‐pot “grafting to” methodology using “thio‐bromo click” chemistry. Atomic force microscopy topographic images show up to 25 times increase in roughness of the coated glass compared to blank glass sample. Contact angle measurements showed that nanosilica coated with PBA and PTFEM produced hydrophobic glass surfaces, while a superhydrophobic and oleophobic surface was generated using nanosilica functionalized with PHFIPA. This novel methodology can produce superhydrophobic and oleophobic surfaces in an easy and fast way without the need for tedious and time‐consuming processes, such as layer‐by‐layer deposition, high temperature calcination, and fluorinated oil infusion. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018     

Crystallization and orientation of isotactic poly(propylene) in cylindrical nanopores

The crystallization of polymers in cylindrical geometries is important as interest in polymer nanowires and nanostructures grows. Here, semicrystalline isotactic poly(propylene) (iPP) is shown to crystallize in a homogeneous, low‐dimensional fashion when confined in cylindrical pores as small as 15 nm. A strong dependence on pore diameter is demonstrated. Isothermal crystallization studies suggest a reduced Avrami exponent as pore diameter decreases and as crystallization time increases. Complementary X‐ray diffraction with tilt (texture analysis) reveals one‐dimensional ordering of iPP crystals within pores of 40 nm diameter or less in which crystals preferentially orient, perpendicular to the pore wall. These findings demonstrate that the origin of this orientation is related to the impingement of crystals against the pore wall, thus “freezing out” polymer crystallizing in nonpreferred directions. These results show that curvature‐directed crystallization is one potential means to control a polymer's crystallization rate and orientation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1412–1419     

Stiffness quantification of conductive polymers for bioelectrodes

Conductive polymer (CP) coatings can improve the performance of metallic bioelectrodes in implantable devices, a benefit which is partially attributed to the “softer” material interface. However, due to the nature of CP fabrication on metallic substrates, accurate quantification of mechanical properties has been difficult to achieve. This study demonstrates that peak‐force quantitative nanomechanical mapping (PF‐QNM) is a robust technique for determining the modulus of CP coatings. The effect of dopant size, chemistry, and film hydration on the mechanical properties of poly(3,4‐ethylene dioxythiophene) (PEDOT) is also examined. Analysis of PEDOT doped with poly(styrene sulfonate) produced across five different thicknesses confirms the utility of PF‐QNM in yielding quantitative, repeatable moduli in both the dry and hydrated state. By doping PEDOT with paratoluene sulfonate and perchlorate (ClO₄) it is shown that the hydrophilicity and the size of the dopant are both critical factors influencing CP mechanical properties in the hydrated environment. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 666–675     

Synthesis and solution properties of well‐defined comb‐on‐comb graft polymers

Well‐defined comb‐on‐comb copolymers of styrene, isoprene, and α‐methyl‐styrene are prepared through cascade “grafting‐onto” methods. The polymer main chain is prepared by nitroxide‐mediated radical polymerization while the branches are prepared by anionic polymerization. The “grafting‐onto” approach employs the coupling chemistry of macromolecular anions, such as polystyryllithium, polyisoprenyllithium, or poly(α‐methylstyryl)lithium, toward either benzyl chloride or epoxy ring on precursor backbones. Thus a series of ABA‐, ABB‐, and ABC‐type comb‐on‐comb copolymers are prepared and characterized by gel permeation chromatography equipped with a multi‐angle laser light scattering detector and a viscometer. Unusual “U‐shaped” dependences of radius of gyration, R_g, on molecular weight are observed for comb‐on‐comb products, which are attributable to delayed elution of the densely grafted copolymers from GPC columns. The result also shows that the comb‐on‐comb copolymers exhibit morphologies from hard sphere to cylindrical rod, depending on the length ratio of the main chain to the branches. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5518–5527, 2008     

Solution behavior of polyimide‐graft‐polystyrene copolymers in selective solvents

A polyimide‐graft‐polystyrene (PI‐g‐PS) copolymer with a polyimide backbone and polystyrene side chains was synthesized by the “grafting from” method using styrene polymerization on a polyimide multicenter macroinitiator via ATRP mechanism. The side chain grafting density z = 0.86 of PI‐g‐PS is rather high for graft‐copolymers synthesized by the ATRP method. Molecular characteristics and solution behavior of PI‐g‐PS were studied in selective solvents using light scattering and viscometry methods. In all solvents, the backbone tends to avoid contact with a poor solvent. To describe the conformation and hydrodynamic properties of PI‐g‐PS macromolecules in thermodynamically good solvents for side chains and PI‐g‐PS, the wormlike spherocylinder model is used. Macromolecules of the studied graft‐copolymer are characterized by high equilibrium rigidities (Kuhn segment length >20 nm). In Θ‐conditions, PI‐g‐PS macromolecules may be modeled by a rigid prolate ellipsoid of revolution with a low asymmetry form and a collapsed backbone as the ellipsoid core. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1539–1546     

Light‐driven atom transfer radical polymerization on supramolecular complexes of conjugated polymers and single‐walled carbon nanotubes

Previous approaches used to decorate latently reactive conjugated polymer‐coated carbon nanotube complexes have utilized “grafting‐to” strategies. Here, we coat the carbon nanotube surface with a conjugated polymer whose side chains contain the radical initiator, α‐bromoisobutyrate, which enables atom transfer radical polymerization (ATRP) from the polymer–nanotube surface. Using light to generate Cu(I) in situ, ATRP is used to grow narrow dispersity polymer chains from the polymer–nanotube surface. We confirm the successful polymerization of (meth)acrylates from the polymer–nanotube surface using a combination of gel permeation chromatography and infrared spectroscopy. Strikingly, we demonstrate that nanotube optoelectronic properties are preserved after radical‐mediated polymer grafting using Raman spectroscopy and photoluminescence mapping. Overall, this work elucidates a method to grow narrow dispersity polymer chains from the polymer–nanotube surface using light‐driven radical chemistry, with concurrent preservation of nanotube optoelectronic properties. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2015–2020     

Synthesis and characterization of synthetic polymer colloids colloidally stabilized by cationized starch oligomers

A method is developed for anchoring enzymatically degraded cationized starch as electrosteric stabilizers onto synthetic latices, using cerium(IV) to create free‐radical grafting sites on the starch. Direct anchoring of debranched starch onto a poly(methyl methacrylate) seed latex yields a latex stabilized by well‐defined oligosaccharides. Using α‐amylase to randomly cleave starch to form (1→4)‐α‐glucans, and a comonomer, N‐isopropyl acrylamide (NIPAM), whose corresponding polymer exhibits a lower critical solution temperature (LCST), creates a means to synthesize block (or graft) oligomers of oligosaccharide and synthetic polymer, which are water soluble at room temperature. Above 30 °C, they become amphiphilic and form self‐emulsifying nanoparticles (sometimes termed “frozen micelles”) from which a synthetic latex is grown after addition of methyl methacrylate, the collapsed NIPAM‐containing entities functioning as a type of in situ seed. This synthesis of stable synthetic latex particles is shown to have a high grafting efficiency. The starch fragments were characterized by ¹H solution‐state NMR before grafting, and ¹³C solid‐state cross‐polarization magic‐angle spinning (CP‐MAS) NMR was used to characterize the starch oligomers actually grafted on the final latex. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1836–1852, 2009     

Atom transfer radical polymerization of n‐butyl acrylate from silica nanoparticles

This article reports the synthesis of atom transfer radical polymerization (ATRP) of active initiators from well‐defined silica nanoparticles and the use of these ATRP initiators in the grafting of poly(n‐butyl acrylate) from the silica particle surface. ATRP does not require difficult synthetic conditions, and the process can be carried out in standard solvents in which the nanoparticles are suspended. This “grafting from” method ensures the covalent binding of all polymer chains to the nanoparticles because polymerization is initiated from moieties previously bound to the surface. Model reactions were first carried out to account for possible polymerization in diluted conditions as it was required to ensure the suspension stability. The use of n‐butyl acrylate as the monomer permits one to obtain nanocomposites with a hard core and a soft shell where film formation is facilitated. Characterization of the polymer‐grafted silica was done from NMR and Fourier transform infrared spectroscopies, dynamic light scattering, and DSC. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4294–4301, 2001     

Macromolecular brushes synthesized by “grafting from” approach based on “click chemistry” and RAFT polymerization

Well‐defined macromolecular brushes with poly(N‐isopropyl acrylamide) (PNIPAM) side chains on random copolymer backbones were synthesized by “grafting from” approach based on click chemistry and reversible addition‐fragmentation chain transfer (RAFT) polymerization. To prepare macromolecular brushes, two linear random copolymers of 2‐(trimethylsilyloxy)ethyl methacrylate (HEMA‐TMS) and methyl methacrylate (MMA) (poly(MMA‐co‐HEMA‐TMS)) were synthesized by atom transfer radical polymerization and were subsequently derivated to azide‐containing polymers. Novel alkyne‐terminated RAFT chain transfer agent (CTA) was grafted to polymer backbones by copper‐catalyzed 1,3‐dipolar cycloaddition (azide‐alkyne click chemistry), and macro‐RAFT CTAs were obtained. PNIPAM side chains were prepared by RAFT polymerization. The macromolecular brushes have well‐defined structures, controlled molecular weights, and molecular weight distributions (M_w/M_n ≦ 1.23). The RAFT polymerization of NIPAM exhibited pseudo‐first‐order kinetics and a linear molecular weight dependence on monomer conversion, and no detectable termination was observed in the polymerization. The macromolecular brushes can self‐assemble into micelles in aqueous solution. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 443–453, 2010     

Combining renewable gum rosin and lignin: Towards hydrophobic polymer composites by controlled polymerization

Rosin polymer–grafted lignin composites were prepared via “grafting from” atom transfer radical polymerization (ATRP) with the aid of 2‐bromoisobutyryl ester‐modified lignin as macroinitiators. Three different monomers derived from dehydroabietic acid (DA) were used for execution of grafting from ATRP, while DA was separately attached onto lignin by a simple esterification reaction. Kinetic studies indicated controlled and “living” characteristics of all monomer polymerizations. Thermal studies indicated that rosin polymer–grafted lignin composites exhibited glass transition temperatures in a broad temperature range from ～20 to 100°C. The grafting of both DA and rosin polymers significantly enhanced hydrophobicity of lignin. Static contact angle measurement of water droplets showed ～90° for all these rosin modified lignin composites. X‐ray photoelectron spectroscopy demonstrated that the surface of rosin–lignin composites was dominated with chemical compositions originating from the hydrocarbon rich rosin moiety. The impartation of hydrophobicity of rosin into lignin provided excellent water resistance of this class of renewable polymers, as all rosin‐modified lignin composites showed water uptake below 1.0 wt %. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Simultaneous reversible addition fragmentation chain transfer and ring‐opening polymerization

The simultaneous ring‐opening polymerization (ROP) of ε‐caprolactone (ε‐CL) and 2‐hydroxyethyl methacrylate (HEMA) polymerization via reversible addition fragmentation chain transfer (RAFT) chemistry and the possible access to graft copolymers with degradable and nondegradable segments is investigated. HEMA and ε‐CL are reacted in the presence of cyanoisopropyl dithiobenzoate (CPDB) and tin(II) 2‐ethylhexanoate (Sn(Oct)₂) under typical ROP conditions (T > 100 °C) using toluene as the solvent in order to lead to the graft copolymer PHEMA‐g‐PCL. Graft copolymer formation is evidenced by a combination of size‐exclusion chromatography (SEC) and NMR analyses as well as confirmed by the hydrolysis of the PCL segments of the copolymer. With targeted copolymers containing at least 10% weight of PHEMA and relatively small PHEMA backbones (ca. 5,000–10,000 g mol^?1) the copolymer grafting density is higher than 90%. The ratio of free HEMA‐PCL homopolymer produced during the “one‐step” process was found to depend on the HEMA concentration, as well as the half‐life time of the radical initiator used. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3058–3067, 2008     

Preparation of remarkably tough polyHIPE materials via polymerization of oil‐in‐water HIPEs involving 1‐vinyl‐5‐aminotetrazole

Interconnected microcellular polymeric monoliths having unexpected high mechanical strength have been prepared using the high internal phase emulsion (HIPE) methodology. Oil‐in water concentrated emulsions of aqueous 1‐vinyl‐5‐amino [1,2,3,4]tetrazole (1‐VAT) mixed with a low molar ratio (7%) of N,N′‐methylenebisacrylamide as crosslinking agent were prepared using dodecane as dispersed phase and a mixture of hydrophilic surfactants. “Reverse” polyHIPE materials were obtained after radical copolymerization, solvent extraction, and drying. Their morphology, chemical composition, and physicochemical behavior are discussed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2942–2947, 2010     

Pyrene functional poly(vinyl alcohol) by “click” chemistry

Side‐chain pyrene functional poly(vinyl alcohol) (PVA) was synthesized by using “click chemistry” strategy. First, partial tosylation of PVA with p‐toluene sulfonyl chloride were performed. The resulting PVA‐Ts polymer was then quantitatively converted into poly(vinyl alcohol)‐azide (PVA‐N₃) in the presence of NaN₃/DMF at 60 °C. Propargyl pyrene was prepared independently as a photoactive click component. Finally, azido functionalized PVA was coupled to propargyl pyrene with high efficiency by click chemistry. Incorporation of pyrene functionality in the resulting polymer was confirmed by spectral analysis. It is also shown that pyrene functionalized PVA (PVA‐Py) exhibited characteristic fluorescence properties and improved solubility in highly polar solvents such as water, DMSO, and DMF as well as less polar solvent such as THF compared with pristine PVA. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1317–1326, 2009     

Polyimide polydimethylsiloxane triblock copolymers for thin film composite gas separation membranes

This article demonstrates the successful fabrication of thin‐film‐composite (TFC) membranes containing well‐defined soft‐hard‐soft triblock copolymers. Based on “hard” polyimide (PI) and “soft” polydimethylsiloxane (PDMS), these triblock copolymers (PDMS‐b‐PI‐b‐PDMS), were prepared via condensation polymerization, and end‐group allylic functionalization to prepare the polyimide component and subsequent “click” coupling with the soft azido functionalized PDMS component. The selective layer consisted of pure PDMS‐b‐PI‐b‐PDMS copolymers which were cast onto a precast crosslinked‐PDMS gutter layer which in turn was cast onto a porous polyacrylonitrile coated substrate. The TFC membranes' gas transport properties, primarily for the separation of carbon dioxide (CO₂) from nitrogen (N₂), were determined at 35 °C and at a feed pressure of 2 atm. The TFC membranes showed improvements in gas permselectivity with increasing PDMS weight fraction. These results demonstrate the ability for glassy, hard polymer components to be coated onto otherwise incompatible surfaces of highly permeable soft TFC substrates through covalent coupling. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3372–3382     

Coupled atom transfer radical coupling and atom transfer radical polymerization approach for controlled grafting from poly(vinylidene fluoride) backbone

A new “grafting from” strategy for grafting of different monomers (methacrylates, acrylates, and acrylamide) on poly(vinylidene fluoride) (PVDF) backbone is designed using atom transfer radical coupling (ATRC) and atom transfer radical polymerization (ATRP). 4‐Hydroxy TEMPO moieties are anchored on PVDF backbone by ATRC followed by attachment of ATRP initiating sites chosen according to the reactivity of different monomers. High graft conversion is achieved and grafting of poly(methyl methacrylate) (PMMA) exhibits high degree of polymerization (DPn = 770) with a very low graft density (0.18 per hundred VDF units) which has been increased to 0.44 by regenerating the active catalyst with the addition of Cu(0). A significant impact on thermal and stress–strain property of graft copolymers on the graft density and graft length is noted. Higher tensile strain and toughness are observed for PVDF‐g‐PMMA produced from model initiator but graft copolymer from pure PVDF exhibits higher tensile strength and Young's modulus. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 995–1008