High‐throughput kinetic analysis of acrylate and thiol‐ene photopolymerization using temperature and exposure time gradients

In this work, a high‐throughput technique for evaluating photopolymers is developed to enable simultaneous measurement of the effects of temperature in combination with exposure time. Temperature and exposure time gradients were produced in orthogonal directions on a single sample, and subsequently sampled using Fourier transform infrared (FTIR) spectroscopy. The technique developed here allows for photopolymerization kinetics to be analyzed rapidly over a large range of industrially relevant temperatures, giving insight into the role temperature and the polymer's glass transition temperature have in dictating the photopolymerization kinetics. In the 70/30 wt % hexyl acrylate and hexanediol diacrylate system, conversion in samples below the glass transition temperature (T_G) was 66 ± 2% after 12 s, significantly lower than the 93 ± 4% conversion at 12 s for samples polymerized at temperatures above the T_G. In addition, a thiol‐ene system was analyzed to study the effect of temperature on the ene homopolymerization in allyl ether monomers, which leads to incomplete thiol conversion in stoichiometrically balanced systems. At a 60% thiol conversion, the allyl ether‐ene conversion at all temperatures is 65 ± 3% irrespective of initial formulation temperature, indicative of the homopolymerization behavior being nearly independent of temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1502–1509, 2008     

Orthogonal multifunctionalization of aliphatic polycarbonate via sequential Michael addition and radical‐thiol‐ene click reactions

Aliphatic polycarbonate (PC) copolymer is synthesized by ring opening copolymerization of acrylate‐ and allyl‐functional cyclic carbonate monomers. The post‐polymerization functionalization of the resulting copolymer is performed quantitatively using a variety of thiol compounds via sequential Michael addition and photo‐induced radical thiol‐ene click reactions within relatively short reaction time at ambient temperature. This metal‐free click chemistry methodology affords the synthesis of biocompatible PC copolymer with multifunctional groups. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1581–1587     

Modular material system for the microfabrication of biocompatible hydrogels based on thiol–ene‐modified poly(vinyl alcohol)

Novel modifications of the synthetic polymer poly(vinyl alcohol) (PVA) were developed for application in the field of biomedical engineering. PVA was modified with allyl succinic anhydride, norbornene anhydride as well as with γ‐thiobutyrolactone to produce macromers with reactive ene and thiol groups, respectively. Cytotoxicity studies have shown that the material exhibits almost no cell‐toxicity, when used in concentrations of 1 and 0.1 wt % for 24 h. The obtained macromers were photocrosslinked via thiol–ene chemistry. Storage stability of the macromer mixtures with different concentrations of pyrogallol as stabilizer were investigated. Photorheometry was employed to optimize mixtures concerning reactivity based on their thiol‐to‐ene ratio, photoinitiator concentration, and macromer content. The crosslinked hydrogels were studied concerning their swellability. To form hydrogels with cellular structure two‐photon‐polymerization (2PP) was employed. Processing windows for 2PP of selected mixtures were determined. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2060–2070     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Facile synthesis of dopa‐functional polycarbonates via thiol‐Ene‐coupling chemistry towards self‐healing gels

Since extraction of the naturally occurring mussel‐foot proteins is expensive and time‐consuming, routes towards synthetic analogues are continuously being explored. Often, these methods involve several protection and deprotection steps, making the synthesis of synthetic analogues time‐consuming and expensive as well. Herein, we show that UV‐initiated thiol‐ene coupling between a thiol‐functional dopamine derivative and an allyl‐functional aliphatic polycarbonate can be used as a fast and facile route to dopa‐functional materials. Different thiol‐to‐allyl ratios and irradiation protocols were used and it was found that nearly 50% of the allyl groups could be functionalized with dopa within short reaction times, without the need of protecting the catechol. It is also demonstrated herein that the dopa‐functional polymers can be used to form self‐healing gels through complexation with Fe³⁺ ions at increased pH. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2370–2378     

Triallyl monomer bearing adamantane‐like core derived from naturally occurring myo‐inositol: Synthesis and polyaddition with dithiols

This paper deals with a triallyl monomer bearing a rigid adamantane‐like core derived from myo‐inositol, a naturally occurring cyclic hexaol. The core structure of the monomer can be readily constructed by orthoesterification of myo‐inositol. The polyaddition of the triallyl monomer with dithiols based on the thermally induced radical thiol‐ene reaction gives the corresponding networked polymers. These networked polymers exhibit much higher thermal stability than the comparative networked polymers obtained from a triallyl monomer bearing less rigid cyclohexyl core. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1193–1199     

Synthesis and characterization of crystalline graft polymer poly(ethylene oxide)‐g‐poly(ɛ‐caprolactone)2 with modulated grafting sites

The graft polymer poly(ethylene oxide)‐g‐poly(?‐caprolactone)₂ (PEO‐g‐PCL₂) with modulated grafting sites was synthesized by the combination of ring‐opening polymerization (ROP) mechanism, efficient Williamson reaction, with thiol–ene addition reaction. First, the precursor of PEO‐Allyl‐PEO with two terminal hydroxyl groups and one middle allyl group was prepared by ROP of EO monomers. Then, the macroinitiator [PEO‐(OH)₂‐PEO]_s was synthesized by sequential Williamson reaction between terminal hydroxyl groups and thiol–ene addition reaction on pendant allyl groups. Finally, the graft polymer PEO‐g‐PCL₂ was obtained by ROP of ?‐CL monomers using [PEO‐(OH)₂‐PEO]_s as macroinitiator. The target graft polymer and all intermediates were well characterized by the measurements of gel permeation chromatography, ¹H NMR, and thermal gravimetric analysis. The crystallization behavior was investigated by the measurements of differential scanning calorimetry, wide‐angle X‐ray diffraction and polarized optical microscope. The results showed that when the PCL content of side chains reached 59.2%, the crystalline structure had been dominated by PCL part and the crystalline structure formed by PEO part can be almost neglected. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2239–2247     

Thiol‐ene photopolymerization of polymer‐derived ceramic precursors

The liquid, ceramic precursor monomer VL20 was copolymerized with a thiol monomer in a traditional radical thiol‐ene photopolymerization. Polymerization occurred via addition of the thiol functional group to the vinyl silazane functional group in a 1:1 ratio consistent with a step‐growth polymerization. Gelation occurred at a high conversion of functional groups (70%) consistent with an average molecular weight and functionality of 560 and 1.7, respectively, for VL20 monomers. Initiatorless photopolymerization of the thiol‐VL20 system also occurred upon irradiation at either 365 or 254 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1752–1757, 2004     

A convenient synthesis of α,α′‐ homo‐ and α,α′‐hetero‐bifunctionalized poly(ε‐caprolactone)s by ring opening polymerization: The potentially valuable precursors for miktoarm star copolymers

Two new ring opening polymerization (ROP) initiators, namely, (3‐allyl‐2‐(allyloxy)phenyl)methanol and (3‐allyl‐2‐(prop‐2‐yn‐1‐yloxy)phenyl)methanol each containing two reactive functionalities viz. allyl, allyloxy and allyl, propargyloxy, respectively, were synthesized from 3‐allylsalicyaldehyde as a starting material. Well defined α‐allyl, α′‐allyloxy and α‐allyl, α′‐propargyloxy bifunctionalized poly(ε‐caprolactone)s with molecular weights in the range 4200–9500 and 3600–10,900 g/mol and molecular weight distributions in the range 1.16–1.18 and 1.15–1.16, respectively, were synthesized by ROP of ε‐caprolactone employing these initiators. The presence of α‐allyl, α′‐allyloxy and α‐allyl, α′‐propargyloxy functionalities on poly(ε‐caprolactone)s was confirmed by FT‐IR, ¹H, ¹³C NMR spectroscopy, and MALDI‐TOF analysis. The kinetic study of ROP of ε‐caprolactone with both the initiators revealed the pseudo first order kinetics with respect to ε‐caprolactone consumption and controlled behavior of polymerization reactions. The usefulness of α‐allyl, α′‐allyloxy functionalities on poly(ε‐caprolactone) was demonstrated by performing the thiol‐ene reaction with poly(ethylene glycol) thiol to obtain (mPEG)₂‐PCL miktoarm star copolymer. α‐Allyl, α′‐propargyloxy functionalities on poly(ε‐caprolactone) were utilized in orthogonal reactions i.e copper catalyzed alkyne‐azide click (CuAAC) with azido functionalized poly(N‐isopropylacrylamide) followed by thiol‐ene reaction with poly(ethylene glycol) thiol to synthesize PCL‐PNIPAAm‐mPEG miktoarm star terpolymer. The preliminary characterization of A₂B and ABC miktoarm star copolymers was carried out by ¹H NMR spectroscopy and gel permeation chromatography (GPC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 844–860     

Synthesis of polyphosphodiesters by ring‐opening polymerization of cyclic phosphates bearing allyl phosphoester protecting groups

The allyl phosphoester group is shown to be a protecting group for the synthesis of anionic polyphosphodiesters. Our strategy relies on the synthesis of a cyclic phosphate monomer bearing a pendant allyl phosphoester group, its easy purification by fractional distillation, its organocatalyzed ring‐opening polymerization by 1,8‐diazobicyclo[5.4.0]undec‐7‐ene (DBU) and 1‐[3,5‐bis(trifluoromethyl)phenyl]‐3‐cyclohexyl‐thiourea (TU). Finally, the deprotection of the allyl phosphoester group is carried out by reaction with sodium benzenethiolate in the absence of any detectable degradation. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2642–2648     

Synthesis of new fluorinated allyl ethers for the surface modification of thiol–ene ultraviolet‐curable formulations

Thiol–ene photocurable systems based on a trifunctional thiol [trimethylolpropane tris‐(3‐mercaptopropanoate)] and two different multifunctional allyl ethers (trimethylolpropane triallyl ether and Boltorn U2, an allyl functional dendritic polyester) were examined. To these systems, small amounts (<1 wt %) of fluorinated allyl ethers were added for the modification of their surface properties. Two new fluorinated allyl ethers, 1H,1H‐perfluoro‐1‐heptylallyl ether and 1H,1H‐perfluoro‐1‐decylallyl ether, were synthesized for this purpose by allylation of the corresponding 1H,1H‐perfluoro alcohols. The fluorinated monomers, despite their very low concentrations, caused sharp changes in the surface properties of the films and in the solvent resistance without any changes in the curing conditions and bulk properties. Completely hydrophobic surfaces were obtained (as a result of the selective enrichment of the fluorinated monomers on the film surfaces) that depended on the monomer structure and its concentration. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2583–2590, 2002     

L‐arabinitol‐based functional polyurethanes

Three new polymerizable diols, based on mono‐, di‐, and tri‐O‐allyl‐L ‐arabinitol derivatives, were prepared from L ‐arabinitol as versatile materials for the preparation of tailor‐made polyurethanes with varied degrees of functionalization. Their allyl functional groups can take part in thiol‐ene reactions, to obtain greatly diverse materials. This “click” reaction with 2‐mercaptoethanol was firstly studied on the highly hindered sugar precursor 2,3,4‐tri‐O‐allyl‐1,5‐di‐O‐trityl‐L ‐arabinitol, to apply it later to macromolecules. A polyurethane with multiple pendant allyl groups was synthesized by polyaddition reaction of 2,3,4‐tri‐O‐allyl‐L ‐arabinitol with 1,6‐hexamethylene diisocyanate, and then functionalized by thiol‐ene reaction. The coupling reaction took place in every allyl group, as confirmed by standard techniques. The thermal stability of the novel polyurethanes was investigated by thermogravimetric analysis and differential scanning calorimetry (DSC). This strategy provides a simple and versatile platform for the design of new materials whose functionality can be easily modified. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Blue LED light‐sensitive benzo pyrazolo (or imidazo) isoquinolinone derivatives in high‐performance photoinitiating systems for polymerization reactions

Isoquinolinone derivatives (IQ) have been synthesized and combined with different additives (an amine, 2,4,6‐tris(trichloromethyl)‐1,3,5‐triazine, an iodonium salt, or N‐vinylcarbazole) to produce reactive species (i.e. radicals and cations) being able to initiate the radical polymerization of acrylates, the cationic polymerization of epoxides, the thiol‐ene polymerization of trifunctional thiol/divinylether, and the synthesis of epoxide/acrylate interpenetrated polymer network IPN upon exposure to very soft polychromatic visible lights, blue laser diode or blue LED lights. Compared with the use of camphorquinone based systems, the novel combinations employed here ensures higher monomer conversions (～50–60% vs. ～15–35%) and better polymerization rates in radical polymerization. The chemical mechanisms are studied by steady‐state photolysis, fluorescence, cyclic voltammetry, laser flash photolysis, and electron spin resonance spin trapping techniques. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 567–575     

Photopolymerization behavior in nanocomposites formed with thiol–acrylate and polymerizable organoclays

Because of the inherent characteristics of the thiol–ene step growth mechanism in preparation of thiol–ene photopolymer clay nanocomposites, the ratio between thiol and ene functional groups at and near the organoclay surfaces may have a significant effect on the polymerization behavior. This study investigates the influence of monomer composition and the type of polymerizable organoclay on thiol–acrylate photopolymerization behavior in preparation of photocurable clay nanocomposite systems. To this end, two types of polymerizable organoclays with acrylate or thiol functional group on the clay surfaces were compared in monomer compositions with different polarity and functionality. Real‐time infrared spectroscopy was used to characterize polymerization behavior in conjunction with photo‐DSC. The degree of clay exfoliation was evaluated using small angle X‐ray scattering and correlated with photopolymerization behavior. Higher chemical compatibility of components induced enhanced clay exfoliation resulting in increase in photopolymerization rate. By affecting the stoichiometric ratio of functional groups in the clay gallery, thiolated organoclays enhance thiol–ene reaction, whereas acrylated organoclays encourage acrylate homopolymerization. In addition, inducing more propagating thiyl radicals on the organoclay surfaces by increasing functionality of thiol monomer also facilitates thiol–ene copolymerization, whereas the increase of acrylate functionality reduces final thiol conversion. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Photoinduced thiol–ene crosslinking of globalide/ε‐caprolactone copolymers: Curing performance and resulting thermoset properties

The increasing demand for bioderived polymers led us to investigate the potential use of the macrolactone globalide in thermoset synthesis via the photoinduced thiol–ene reaction. A series of six lipase‐catalyzed poly(globalide‐caprolactone) copolyesters bearing internal main‐chain unsaturations ranging from 10 to 50 and 100 mol % were successfully crosslinked in the melt with equal amounts of thiol groups from trimethylolpropane‐trimercapto propionate affording fully transparent amorphous elastomeric materials with different thermal and viscoelastic properties. Three major conclusions can be drawn from this study: (i) high thiol–ene conversions (>80%) were easily attained for all cases, while maintaining the cure behavior, and irrespective of functionality at reasonable reaction rates; (ii) parallel chain‐growth homopropagation of the ene monomer is insignificant when compared with the main thiol–ene coupling route; and (iii) high ene‐density copolymers result in much lower extracted sol fractions and high T_g values as a result of a more dense and homogeneous crosslinked network. The thiol–ene system evaluated in this contribution serve as model example for the sustainable use of naturally occurring 1,2‐disubstituted alkenes in making semisynthetic polymeric materials in high conversions with a range of properties. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012.     

Synthesis of water‐soluble allyl‐functionalized oligochitosan and its modification by thiol–ene addition in water

A novel, straightforward and versatile chemical pathway has been studied to functionalize water‐soluble chitosan oligomers. This metal‐free methodology is based on the epoxy‐amine reaction of the allyl glycidyl ether with chitosan, followed by thiol‐ene radical coupling reaction of ω‐functional mercaptans, using 4,4′‐Azobis(4‐cyanovaleric acid) as a free radical initiator. Both reactions were entirely carried out in water. In a preliminary step, chitosan depolymerization was carried out using H₂O₂ in an acetic medium under 100 W microwave irradiation, optimizing the yield of water‐soluble oligomers. Functionalization by six different thiols bearing alcohol, carboxylic acid, ester, and amino groups was then performed, leading to a range of functional oligochitosans with different grafting efficiencies. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 39–48     

Photopolymerization of ternary thiol–ene/acrylate systems: Film and network properties

Photocurable, ternary‐component mixtures of a 1:1 molar multifunctional thiol–ene (trithiol and triallyl ether) blend and a 16‐functional acrylate based monomer have been photopolymerized, and the final film properties of the ternary crosslinked networks have been measured. The photopolymerization kinetics, morphology, and mechanical and physical properties of the films have been investigated with real‐time infrared, atomic force microscopy, and dynamic mechanical analysis. The photopolymerization process is a combination of acrylate homopolymerization and copolymerizations of thiol with allyl ether and acrylate functionalities. The tan δ peaks of the photopolymerized ternary systems are relatively narrow and tunable over a large temperature range. The morphology is characterized by a distinct phase‐separated nanostructure. The photocured thiol–ene/acrylate ternary systems can be made to exhibit good mechanical properties with enhanced energy absorption at room temperature by the appropriate selection of each component concentration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 822–829, 2007.     

Photo‐induced thiol‐ene polysulfide‐crosslinked materials with tunable thermal and mechanical properties

Photo‐induced thiol‐ene crosslinked polymeric networks have been extensively explored in constructing a variety of new materials with enhanced mechanical properties for optical, biomedical, and sensing applications. Toward the broad applications, however, tunable mechanical properties are greatly desired. Here, an effective approach utilizing high‐molecular‐weight methacrylate copolymers having pendant thiol and vinyl groups (MCPsh and MCPenes) to modulate thermal and mechanical properties of photo‐induced thiol‐ene crosslinked materials is reported. The MCP copolymers are synthesized by an industrially friendly polymerization method, followed by post‐modification including either a facile coupling reaction or reductive cleavage. Upon UV irradiation, thiol‐ene reactive blends of MCPsh and MCPenes yield highly crosslinked materials through the formation of flexible sulfide linkages. These polysulfide‐crosslinked materials based on rigid MCP backbones exhibit enhanced mechanical properties. Further, their thermal and mechanical properties are tuned by modulating monomer compositions of MCPs as well as varying numbers of pendant SH or vinyl groups (i.e., extent of crosslinking densities). This approach is versatile and effective for development of high performance polymeric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3060–3068     

UV‐curable thio‐ether‐urethane network with tunable properties

A photoinitiating system composed of a sensitizer (isopropylthioxanthone, ITX) and a photobase generator (triazabicyclodecene tetraphenylborate TBD.HBPh4) was successfully applied to the photopolymerization of a thiol‐isocyanate‐epoxy mixture. The final polymer network was considered in term of the compositional ratio between the thiol‐isocyanate and thiol‐epoxy coupling reactions. In parallel with structural investigation by spectroscopic technics, the relationships between the compositional ratio and kinetics of photopolymerization, thermomechanical properties and hardness were investigated. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3119–3126     

Three‐dimensional microfabrication of protein hydrogels via two‐photon‐excited thiol‐vinyl ester photopolymerization

Engineering three‐dimensional (3D) hydrogels with well‐defined architectures has become increasingly important for tissue engineering and basic research in biomaterials science. To fabricate 3D hydrogels with (sub)cellular‐scale features, two‐photon polymerization (2PP) shows great promise although the technique is limited by the selection of appropriate hydrogel precursors. In this study, we report the synthesis of gelatin hydrolysate vinyl esters (GH‐VE) and its copolymerization with reduced derivatives of bovine serum albumin (acting as macrothiols). Photorheology of the thiol‐ene copolymerization shows a much more rapid onset of polymerization and a higher end modulus in reference to neat GH‐VE. This allowed 2PP to provide well‐defined and stable hydrogel microstructures. Efficiency of the radical‐mediated thiol‐vinyl ester photopolymerization allows high 2PP writing speed (as high as 50 mm s^?1) with low laser power (as low as 20 mW). MTT assays indicate negligible cytotoxicities of the GH‐VE macromers and of the thiol‐ene hydrogel pellets. Osteosarcoma cells seeded onto GH‐VE/BSA hydrogels with different macromer relative ratios showed a preference for hydrogels with higher percentage of GH‐VE. This can be attributed both to a favorable modulus and preferable protein environment since gelatin favors cell adhesion and albumin incurs nonspecific binding. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4799–4810